Search Documents

By K. Saberyan

In this study, solvent extraction of zirconium by using triphenylphosphine oxide as extractant has been investigated. The results showed that extraction of zirconium by triphenylphosphine oxides in nitric acid and hydrochloric acid media were negligible. Extraction of zirconium in acetic acid media with concentration of 0.01~0.2 M has been studied and the results showed that the maximum percent of zirconium extraction was 40% in acid acetic with concentration of 0.01 M. By addition complexing agents such as potassium thiocyanate with the concentration of 0.01~0.2 M zirconium extraction increased up to 86% in 0.2 M potassium thiocyanate. By addition of sodium salicylate with concentration of 0.01 M and in pH=2.5, the maximum extraction of 96% was achieved. The striping of zirconium from organic phase can be carried out by 0.5 M solution of sulfuric acid.

Jan 1, 2014

By Chi Zhang, Junyi Wu

"With the increasing popularity of lithium cobalt oxide in lithium ion battery industry, which is driven by new energy vehicle and mobile device applications, the demand of cobalt is also growing rapidly in recent years. There is a significant trend of increasing investment on cobalt capacity in China, and the automation renovation is considered as an option of improving production efficiency. This study aimed at evaluating the practicability of stainless permanent cathode blank and automatic stripping process in cobalt electrowinning process. The purpose is to replace the old starter sheet process in cobalt electrowinning, which so far was used by most of cobalt refineries in China, but very labor intensive and exposed operators to serious aerosols that contained both cobalt and acid. In the old starter sheet process, the initial cobalt starter sheet is produced onto a plate made of titanium, while the titanium cathode blank and hanger bar fit the critical corrosive environment but is lack of mechanical strength for automatic production which has been mature in copper electrowinning process. To evaluate the proper materials instead of titanium, the coupon corrosion tests with different raw materials including 316L and other stainless steel grades were held for several months in production environment at a cobalt tank house in China. Following the comparison between titanium and other tested materials, a pilot production test in a cobalt tank house is also on-going.INTRODUCTION Cobalt has been known in early China and used in pottery glazes, and the ancient Greeks and Romans used its compounds to make colored glass since long time ago. The blue on the colored porcelain from the Tang Dynasty in China was also due to the presence of cobalt compounds. The word cobalt is known being derived from the German kobalt, from kobold meaning ""goblin"", because the cobalt-bearing blue ore, CoAsS, was called kobaltin in Europe in the Middle Ages, it may have been thought to be harmful to the health of the miners because of arsenic in the ores."

Jan 1, 2018

By D. Govender

Theoretical flotation models suggest that there is a positive relationship between bubble-particle collision rates and turbulent kinetic energy dissipation. Fine particle flotation performance is generally enhanced by increased collision frequency and hence higher energy dissipation. Contrarily, increased turbulence in the rotor-stator region is related to higher detachment frequency of the coarser size range. Therefore, the optimal modes of recovery for the ?fine? and ?coarse? size classes are diametrically opposed. Industrial applications have previously confirmed that applying greater power to flotation slurries yields significant improvements in fine particle recovery. However, recovery of the coarser size class favors a different flotation environment. An improvement in the kinetics of the fine and coarse size classes, provided there is no adverse metallurgical influence on the intermediate size ranges, is obviously beneficial to the overall recovery response. Managing the local turbulent kinetic energy dissipation, and hence the power imparted to the slurry, offers the benefit of targeting the particle size ranges exhibiting slower kinetics. FLSmidth recently introduced the practical implementation of this concept. In principle, it decouples flotation regimes where fine and coarse particles exhibit preferential recovery. In the case of naturally aspirated machines (Wemco®), it is referred to as Hybrid Energy Flotation? and incorporates at least three phases: ? Standard flotation machines (standard energy input, rpm, rotor size/type) at the beginning of the row, where flotation is typically froth phase limited and operational, and set-up parameters have a limited influence on the recovery. ? Higher-powered flotation machines (high rpm, high power rotor size/type) at the end of the row to improve fine particle recovery. ? Lower-powered flotation machines (low rpm, low power rotor size/type) to enhance coarse particle recovery. In evaluating the effect of turbulent kinetic energy on flotation performance, the spatial distribution and its effect on size denominated recovery needs to be evaluated. The mean energy dissipation rate is a measure of the bulk energy input, but CFD-based models offer a more introspective view of flotation sub-processes. A CFD-based flotation model is used to highlight the effect of turbulent dissipation energy on attachment and detachment rates. Preferential collection zones for ?fine? and ?coarse? particles are predicted for both forced air and naturally aspirated machines. Keywords: CFD-based model, attachment, detachment, energy dissipation, hybrid energy flotation?, forced air, naturally aspirated

Sep 1, 2012

By S. J. Ma

With the very effective depressant and collector developed by China Bluestar Lehigh Engineering Corp (hereinafter referred to as LEHIGH), satisfied results are obtained from laboratorial beneficiation tests on phosphate samples from Karatau, Republic of Kazakhstan by the direct flotation process. In this paper the effect of single factors on performance of flotation is studied and their applicable ranges are proposed. The final test results are described as follows: As the feed contains 23.20 % P2O5, and 3.96% MgO, a phosphate concentrate assaying 29.77%P2O5 and 1.54% MgO is produced, and the P2O5 recovery in concentrate is 88.28%. The beneficiation tests make it possible to simplify existing technology with fine grinding-desliming, followed by reverse & direct flotation system and consequently improve the concentrate grade and recovery for the future beneficiation plant

Jan 1, 2014

By T. C. Alex

Mechanical activation of gibbsite [?-Al(OH)3] is the theme of this paper. Industrially prepared gibbsite used in the study has a mono modal size distribution with a median size, d50=110 µm. Mechanical activation of this gibbsite has been carried out in a planetary mill at ambient conditions. Mechanical activated gibbsite samples are characterised in terms of particulate characteristics, structural characteristics and reactivity. As a result, of milling, mono modal size distribution of the unmilled gibbsite changes to a broad multimodal distribution. Size reduction has been sharp in the initial stages of milling; median size reduces to ~7 µm during 15 min of milling. Thereafter no decrease in median size is observed; rather it is found to increase gradually with further increase in milling time, indicating particle aggregation. Morphological studies of milled gibbsite have shown that the platelets forming the agglomerate are separated first; the separated platelets then undergo breakage. Aggregation of particles sets in the later stages of milling as a result of increased surface area and surface energy. X-ray diffraction (XRD) and transmission electron microscopy (TEM) studies have clearly revealed the changes in gibbsite structure during milling. Analyses of XRD data show that the crystallite size of gibbsite decreases as the milling time progresses whereas its microstrain is found to increase. Accumulation of energy in the structure is the result in both cases. TEM micrographs with signs of defects leading to disordering of gibbsite structure complement the XRD results. Reactivity of milled gibbsite, decrease in its deydroxylation temperature and increase in alkali dissolution, is found to increase with mechanical activation. Increased reactivity of milled gibbsite is found to have a strong correlation with the BET specific surface area. Keywords: mechanical activation, gibbsite, alkali dissolution, thermal dehydroxylation, reactivity

Sep 1, 2012

By V. K. Kuppusamy, M. Holuszko

"Lamps and lighting products are the most commonly used electrical products around the globe. With the improvement in lamp technologies, lighting products have grown complex and hence require an improved recycling process. The LED lamps consist of various valuable metals such as iron, copper, aluminum, chromium, silver, and gold, as well as non-metals such as glass, plastics, and fibers. In addition, there are also traces of hazardous substances such as lead, arsenic, and mercury. A major step in the recovery process is size reduction, and researchers have suggested that up to 40% of the total valuable material is lost during the shredding and grinding processes. SELFRAG is a high voltage selective fragmentation comminution technology that uses high voltage pulses in a water medium to efficiently separate the metals at a coarser size without generating many fine particles. It has been proposed that during the fragmentation process of electronic waste (e-waste), the metals can be separated without fine grinding. This research considers the applicability of high voltage pulse fragmentation for LED lamps. Eight different types of LED lamps were processed through the SELFRAG unit at varying pulses to study metal liberation. The product obtained was characterized for metal liberation, metal grades, and liberation analysis. The specific energy consumption for this size reduction process was also monitored. INTRODUCTION Lamps and bulbs are the most commonly used electrical products in homes, offices, industrial operations, and streets. According to Energy Star research (2006), an average US household has more than 40 sockets for light bulbs and consumes approximately 2100kWh every year for lighting. The development in lamp technology has pushed the boundary for newer products. The LED lamps have been taking over the market from the incandescent bulbs and compact fluorescent lamps (CFL). According to the US Department of Energy (2012) and myLEDlight.com (2007), LED lamps have several benefits over other lamps. LEDs produce light hemi-spherically, which increases their efficiency in directional light emission. It has higher breakage resistance from vibration or transportation. LED lamps use up to 90% less power than incandescent bulbs thus making them highly energy efficient; They have a longer lifespan, lasting 10 times longer than a CFL and 133 times longer than the traditional incandescent bulb. Because of all the benefits, Smallwood (2014) suggested that the market of LED lamps will grow to $12.2 billion by 2018."

Jan 1, 2018

Anglo American Platinum practices fine grinding in its processing plants to enhance the liberation of valuable minerals. If the fine particles of valuable minerals generated during fine grinding are not recovered during the flotation process, this could significantly contribute to the overall losses. This study examines the flotability of fine moncheite (PGE mineral) particles in a controlled environment (moncheite size distribution, concentration and liberation). A barren Norite ore ground to 40% and 80% passing 53µm was spiked, with four different size fractions of moncheite (-5, -10+5, -25+10 and -53+25µm) in order to evaluate the effect of particle size on flotation. The investigation also included the effect of energy input and collector dosage on the flotation of two moncheite size fractions, namely -5µm and -10+5µm. The results showed that the moncheite particle size has a significant impact on flotation. Coarse particles (-53+25µm) showed the highest Pt flotation kinetics and overall recoveries. The -5µm size fraction of moncheite could also be recovered by flotation, however, at a lower rate compared to the other size classes investigated. The increased collector dosage of 300g/t at the finer Norite grind of 80% passing 53µm enhanced the flotation rate of the -5µm size fraction of moncheite when compared to the lower collector dosage of 150g/t. The higher energy input during laboratory flotation, at an impeller speed of 1000rpm also increased the flotation rate of the -5µm size range, however, at a lower concentrate grade, when compared to the lower impeller speed of 700rpm. More favourable Pt flotation kinetics data was obtained for the -53 +25µm size fraction of moncheite at the fine Norite grind when compared to the coarse Norite grind. Keywords: flotation, moncheite, particle size, energy input and SIBX

Sep 1, 2012

By A. Shibayama

Soil contamination by organic compounds is one of the most concerned issues on polluted soil. It is well known that there are limited methods to remediate the contaminated soil on site. Especially, the in-situ method for contaminated soil is too difficult to de-contaminate the organic pollutant. In this study, the fundamental ability of soil remediation, which aimed to decrease oil concentration in, in-situ process, have been researched by using a high pressure gas generated from ?crush composition? on artificially oil contaminated soil. The n-hexadecane (n-C16H34) and other organic compounds were selected as soil oil contaminators, gravimetric analysis by soxhlet extraction and GC-MS were used as qualitative and quantitative analysing methods. For the experimental examination, the influences on the difference in the concentration of n-hexadecane (and other organics), the tamping amount, position and repetition of crush composition in soil, and scale (size) of experimental model were investigated. The n-hexadecane concentration reduced by the explosive effect of crush composition showed a reasonable decrease of about 30 wt%~60 wt% compared to the initial n-hexadecane. The removed amount of n-hexadecane and distance from explosion point of the crush composition was related in scale and model of contaminated soil.

Jan 1, 2014

By Zehong Wang

Selecting sodium polyacrylate (PAAS) as grinding aid, the effect of grinding aid on the grinding efficiency of bauxite taken from Shanxi province was studied and its mechanisms were analyzed by measuring the variation of adsorption characteristic, pulp viscosity, surface electric potential of the bauxite and the surface appearance of particles. The results showed that, compared with no grinding aids added the content of -0.074mm in the ground product was increased by 5.45 percentage points under the optimal grinding conditions adding PAAS as grinding aid when the amount of PAAS was 0.7%wt of bauxite. Because the physical adsorption and chemical adsorption were occurred on the bauxite surface, which could reduce the pulp viscosity, change the surface electric potential of the bauxite, enhance the surface appearance of particles and lower the surface hardness of the bauxite, the grinding efficiency of bauxite was increased by PAAS. Keywords: bauxite, grinding aids, grinding efficiency, mechanism

Sep 1, 2012

Coal preparation plants usually operate with water in a closed circuit mode. In this practice, large quantities of water is continuously being recycled. To compensate the natural losses, only small quantity of fresh make up water is added into the circuit. As a result, a gradual build up of residual concentrations of flotation reagents (frothers, collectors, coagulates etc.) take place in the water and the concentration levels of the contaminants increase. Besides, the recycled water accumulates higher amounts of total dissolved components (1600 ppm) and hardness (740 ppm) than the fresh water. Nearly 80 ? 85% of the process water used in a coal preparation plant is utilized in treating the coal fines in flotation circuit. The presence of certain alkali earth metal ions (e.g., Ca++, Mg++) may adversely affect the flotation performance as they precipitate sparingly soluble hydroxyl complexes on the coal surface and change its surface charge. These studies showed that the use of recycled water in flotation has a significant effect on the selectivity and kinetics of the flotation process because, the dissolved compounds, both inorganic and organic, alter the chemistry radically. By treating the recycled water through a softening process, the concentrations of alkali earth metals and hardness were reduced significantly. The concentration of alkali earth metals and hardness were reduced to 10 ppm and 35 ppm respectively in the softened recycle water. From the selectivity studies, it has been observed that the flotation yield and recoveries increased by four to seven units by softening the recycled water. The kinetic studies indicated that the clean coal particles followed first-order kinetics. The kinetic parameters namely, flotation rate constant (k) and maximum recoveries (R8) of flotation, were found higher with softened recycle water than the recycled water. This reduces the residence time in the flotation cell and thereby, increases its productivity. Keywords: coal flotation, hardness of water, water chemistry, softening process, selectivity, kinetics, flotation rate constant and maximum recovery

Sep 1, 2012

Much has been published in recent years on the challenges facing the engineer of the 21st century and the consequent challenges facing the education providers and industry. The world is changing rapidly on the social, economic, political, technical and environmental fronts and our metallurgists/mineral processing engineers of the future will arguably need to have a different set of skills than those which were traditionally regarded as adequate during the latter half of the 20th century. This paper attempts to explore some of these issues and their ramifications.

Jan 1, 2014

By Ana C. C. Pacheco, Maurício L. Torem

"The aim of this work was the study of the effect of the type (Fe3+, Al3+ and Fe3+ and Al3+ mixture) and of the coprecipitant concentration on As5+ removal by ACF. Removal of As5+ using Sodium Dodecylsulfate (SDS) as a collector was studied by Adsorbing Colloid Flotation (ACF) at laboratory scale. The morphology of the precipitate retained in the foam was analyzed by Scanning Electron Microscopy (SEM/EDS).By comparing the coprecipitant type and concentration studies it could be concluded that As5+ removal in the presence of Fe3+ (160 mg.L-1) alone, or a Fe3+ (80 mg.L-1) and Al3+ (40 mg.L-1) mixture, is equivalently effective (99,9%) and greater than in the presence of Al3+ (80 mg.L-1) alone (97,7%).Through SEM/EDS analyses, it was possible to observe that both morphology and composition of the precipitate produced in the solution and retained in the foam depend on the physico-chemical conditions of the system, that is, on the species present in the solution."

Jan 1, 2003

By H. Deng

Oxidized zinc ores are the main source of zinc metal except sulfides. To have a better understanding about the performance of smithsonite and the main gangue, quartz, in flotation, the aggregation behaviors of smithsonite and quartz in water were confirmed by different techniques (sedimentation tests and optical microscopy). The experimental results show that smithsonite and quartz particles aggregate in the pH range 7.5-11. The results of zeta potential suggest that the aggregation does not correlate with the DLVO theory, when the iso-electric point of smithsonite and quartz is 8.0 and 2 respectively. When the solution pH is less than 8.0, smithsonite has an opposite charge to the quartz particles. Electrostatic adsorption makes effort on these two kinds of particles according to DLVO theory. Whereas, solution chemistry calculation shows the pH range 8-11 corresponds to hydroxide formation, suggesting that this is the species responsible for aggregation. And their concentrations are much higher in sodium hydroxide system than that in sodium carbonate system. Aggregation of smithsonite and quartz due to the flocculation action of zinc hydroxide is proposed.

Sep 1, 2012

By Ghislain Bournival, Cagri Emer, Seher Ata

"It is well known among flotation practitioners that the contact angle can be correlated with the amount of material recovered from feed by flotation. The contact angle of solids can easily be modified by the addition of a collector. However, some collectors also have frothing properties thus altering the solid and bubble surface properties simultaneously. To avoid this problem, a technique has previously been used in which silanol groups are attached to the surfaces of the particles, but this method has its own problems. In this work, silica particles with various surface hydrophobicities were prepared using an esterification process. By using alcohols with different hydrocarbon chain lengths, from 4 to 12 carbon atoms, surfaces with a wide range of contact angles could be prepared. The technique was used in the modification of silica particles that were tested in a fluidized bed flotation column, and a laboratory mechanical flotation cell. In parallel experiments, dodecylamine (DDA) was used as a collector. It was found that irrespective of the type of flotation machine and surface preparation method, there was a close correspondence between flotation recovery and the contact angle of the particles. The silanation process has known drawbacks relating to the presence of moisture during the reaction, and the stability of the silane coating after it is been prepared. Esterification does not suffer from these disadvantages. This work has shown that the esterification technique is a robust alternative method for preparing hydrophobic quartz surfaces."

Jan 1, 2014

By Xiaoming Wang

This paper describes a new magnetic separator integrating dynamic permanent magnetic force, gravity and flow dynamics to enhance the quality of the iron concentration. This equipment can increase the grade of concentrate by controlling the formation of magnetic agglomerations to reject most gangue. Test results indicates that the compound force field separator can be applied in improving the quality of iron concentrate and has a wide range of potential market applications. Keywords: magnetic separator, compound force field, rotating magnetic system, magnetite concentration

Sep 1, 2012

By I. Dymov

"The extractive metallurgy of precious metal ores involves gravity concentration, flotation and cyanide leaching. Pre-oxidation, such as roasting, autoclaving, bacterial oxidation and other techniques, is required for processing refractory ores. Selection of the process is mainly driven by the grade, reserve and mineralogy of the target elements. The concentrations of precious metals in the crust are extremely low and highly variable, resulting in ore variability in many gold, silver and PGE deposits. More importantly, precious metals in an ore may occur in two or three forms (i.e. microscopic, submicroscopic and surface-bound), making ore processing of precious metals extremely challenging. The objective of geometallurgy and process mineralogy is to reduce and minimize the technical risk in project evaluation, process selection, mine planning and production forecasting through geometallurgical modelling, representative sampling and subsequent systematic mineralogical characterization and metallurgical testwork. Geometallurgy is a technique to document variability within an orebody and quantify and evaluate the impact of many factors including geology and mineralogy on grinding, flotation, leaching and metal recovery processes, while mineralogy is one of the major predictive and trouble-shooting tools for many new mineral projects and operating mines. This paper presents an overview of fundamentals, methodologies and techniques applied in geometallurgy and process mineralogy and highlights the importance of both disciplines in process selection and plant optimization with applicable case studies. INTRODUCTION Precious metals, including gold, silver and platinum group elements (PGE) occur in various geological settings and ore types. The concentrations of these metals in the crust are extremely low and highly variable, resulting in ore variability in many gold, silver and PGE deposits. More importantly, precious metals in an ore may occur in two or three forms (i.e. microscopic, submicroscopic and surface-bound), making ore processing of precious metals extremely challenging. Process selection is most important in any precious metals project and is mainly driven by the grade, reserve and mineralogy of the target elements. Free-milling ores, such as Kupol in Russia, Hemlo in Canada, Grasburg in Indonesia, UG-2 in South Africa, Lac des Iles in Canada, and Noril’sk in Russia, can be processed using flotation or cyanidation with or without gravity. B2Gold Corp, a Canadian gold company, just started a number of new and under construction free-milling gold operations such as Fekola mill in Mali, Mastbati mine in Philippins and Otjikoto mine in Nambia. However, refractory ores (particularly gold ores), such as the Carlin and Goldstrike mines in the USA, Giant in Canada, Pueblo Viejo in Dominican Republic, Porgera and Lihire in PNG, Kittilla in Finland, Fairview in South Africa and Shuiyindong in China, must be processed using pre-oxidation prior to cyanide leaching. In some mildly refractory gold ores, such as Kumtor mine in Kyrgyzstan and KCGM in Australia, ultrafine grinding is required to liberate fine-grained gold particles. For some gold ores containing both free-milling and refractory components (such as Cripple Creek mine in Colorado, USA), two or more recovery processes may be required. The variability of grade, metal deportment, ore hardness and other parameters is one of the risks that encountered in development and operation of many precious metals projects. To minimize and reduce the technical risk caused by ore variability, geometallurgy and process mineralogy have been used by mining companies in the last two decades to measure and quantify the spatial variability of the deposits that are being developed. This paper presents an overview of fundamentals, methodologies and techniques applied in geometallurgy and process mineralogy, it highlights the importance of both disciplines in process selection and plant optimizat"

Jan 1, 2018

By Liang Dianyin

In this paper, the molybdenite flotation tailing of cleaner-scavenger bank which has a mass of very fine particles has been taken as raw ore to be processed by flotation with/without ultrasonic. The effect of ultrasonic frequency, intensity, processing time and uploading location on molybdenite flotation efficiency is investigated by four-factor three-level orthogonal experiment, and the effect significances of these ultrasonic variables to molybdenite flotation efficiency have also been evaluated. Single-factor analysis of variance is conducted to investigate whether the effect of ultrasonic on molybdenum ore flotation efficiency is significant or not. The samples extracted from different ore species in different time have been mixed to analyze the particle size. The results show that the particle size of +38µm in concentrate obviously increases while the particle size of -25µmobviouslydecreaseswith ultrasonic, which means that ultrasonic is good for flotation due to sludge removing effect. Keywords: ultrasonic, flotation efficiency, sulfide ore, tailing, grade, sludge removing

Sep 1, 2012

Vanadium-titanium magnetite from Panzhihua was crushed with open and closed circuit process by high pressure grinding roller (HPGR). The particle size characteristics of the crushed product were analyzed and the micro-cracks generated by HPGR during the crushing process were studied. The results showed that, in crushed products, the reduction ratio increases and the size distribution becomes more uniform with increasing of the pressure on roller?s surfaces. The fine fraction content of crushing products from -3.2 mm classification closed-circuit by HPGR increases obviously compared with that by Jaw Crusher and particle size distribution is more uniform. Large amount of intra-crystalline cracks and cleavage cracks are generated in vanadium-titanium magnetite crushed by HPGR, which makes the specific surface area larger and Bond grinding work index (objective particle size is 0.074 mm) decreased by 14.05% than that by Jaw Crusher. And the liberation degree of monomer of the product crushed by HPGR increased compared with that by Jaw Crusher with the similar fineness of grinding. Keywords: iron ore, high pressure grinding roller, micro-crack

Sep 1, 2012

By G. C. He

Effects of irregularity, rough surface and aggregation of fine particles on ultrasonic attenuation are significant. The effects should be considered while predicting particle size by ultrasonic attenuation technology. The scanning electron microscope micrographs analysis also shows that particles surface is rough and irregularity. Any slurries has its fractal structure and its special fractal scale and dimension, so, effects of irregularity, rough surface and aggregation of fine particles can be de-scribed by fractal model. The discrepancies between predictions of ultrasonic attenuation based on the assumption of smooth spherical particles and data obtained from slurries of irregular particles indicated that there were different fractal structures. The ultrasonic attenuation model was modified by fractal dimensions. The result of experimental data and analogue calculation indicated that pre-dictions of the fractal modification of ultrasonic attenuation model show good agreement with experimental data. On the other hand, from the values of fractal obtained by inversely calculation, the degree of effects of irregularity, rough surface and aggregation of particles can be estimated. The positive value of fractal dimension indicates that the aggregation has the dominant effect on ultra-sonic attenuation, otherwise, the irregularity and rough surface has the dominant effect.

Jan 1, 2014

By L. Rintala

The design of a hydrometallurgical process starts with the analysis of the raw materials to be treated, for example mineralogy, chemistry, deposit size are analysed. Based on this information suitable unit processes for pre-treatment, leaching, solution purification and product recovery are selected. Typically, process design for the new ore deposit relies on laboratory tests such as pre-treatment and leaching experiments. The experimental work is the most time consuming and expensive part of the process design. Reducing the number of experiments would shorten the time of designing a new flowsheet or development of new process technology. A large amount of information is available about the hydrometallurgical experiments and the amount is increasing continuously. For example, word search using ?hydrometallurgy? from Scopus database results in over 4 000 publications with the word in title, abstract or keywords. This number consists of 2 500 articles, 900 conference papers, and 90 reviews since 1972. The number of hydrometallurgical publications per year has increased from 13 in 1972 to 150-200 in the last few years. The objective of this study was to analyze how detailed data of experiments about the gold extraction is published and how that data could be exploited more effectively when designing hydrometallurgical processing for new ore. The leading idea is that similar ores should have the similar response in leaching. If the published information was used more efficiently, the amount of experiments would be reduced. More than 200 cases of experimental data of gold leaching have been analyzed for this study. There are over 30 factors that could be used in comparison when selecting process alternatives, but challenging fact is that not all these factors are documented in all publications. Results show that the usefulness of the published data in the development of hydrometallurgical flow sheet for gold using decision-support tools is not that straightforward. The quality of the published information about gold extraction varied between the publications and the descriptions of the raw materials, experimental arrangements and results were often missing details. Methods to normalize the data for description of the cases and a system to describe different features unambiguously are needed. Keywords: refractory gold, host mineral, leaching, data analysis, case-based reasoning

Sep 1, 2012