Search Documents

By Andreea Catalina Gluhoi

Oxidation and reduction reactions of N-containing molecules have been studied over different types of gold-based catalysts, Au/MOx/Al2O3 and Au/MIOx/MIIOx/Al2O3 (M, MI, MII=Li, Rb, Mg, Ce, Zr, Mn, Cu) prepared by deposition precipitation with urea. In general, all the catalysts were already active at low temperatures. NH3 oxidation was effectively catalyzed by Au/CuO/Al2O3, a catalyst which also gives the highest yield in N2. NO reduction by H2 performed over gold-based catalysts produced N2O, N2 and NH3 and N2O reduction resulted in the formation of dinitrogen. For all the reactions, large synergistic effects have been obtained by addition of different kind of additives.

Oct 1, 2003

By G. Plascencia, A. Warczok, M. Zamalloa, T. Utigard, N. Behnood

The objective of this investigation was to investigate interactions between high-grade copper mattes and Rexal 60DB direct bonded basic bricks. The infiltration and attack of Rexal 60DB bricks by copper matte and continuous converter matte was investigated in laboratory tests at temperatures up to 1300 °C. The brick dissolution and infiltration tests did not show any significant difference between the 70% Cu and the 81% Cu mattes. More metallic copper was visible in the pores in the case of 81% Cu matte. An important mechanism for direct-bonded magnesia-chrome brick destruction is that oxysulphides start to infiltrate the brick, followed by slow oxidation of the matte producing metallic copper and cuprous oxide, which then react with MgO and Cr2O3, primarily attacking the direct bonds of the brick.

Jan 1, 2004

By Eva Surová, Molák. Bohumil, Márta Polgári

The Úrkút rhodochrosite deposit and Branisko Mn showings (rancieite, manganiferous calcite), located in Lower Jurassic marine sedimentary rocks with black shale, were studied by organicgeochemical methods. Both depositional localities were affected by the Lower Jurassic Toarcian anoxic event. UrkUt shales are rich in organic matter (av. 2.94 wtOJo total organic carbon), the composition of which indicates derivation mainly from marine sources, with some terrigenous component. The shales matured in a bacterially active environment under reducing conditions of diagenesis-catagenesis. Branisko shales (~0.2 wt % TOC) with lenses of Mn oxide ore were weakly metamorphosed and their organic matter thermally degraded. The model for Mn carbonate ore formation envisages reaction of Mn derived from sediments, with carbonate generated by a bacterially mediated process of decomposition of organic matter that also involved Mn reduction.

Jan 1, 1992

By A. Rahimi

The smelting plant at Sarcheshmeh Copper complex commenced working with two reverbatory furnaces, four pierce smith converters, two anode furnace and one holding furnace having a known capacity of 420 metric tons of anodic copper according to the initial design in 1982 (1361 Iranian calendar). During the period from the commencement date up until now, the smelting plant has undergone changes for improvement and enhanced production by substituting holding furnace with another anode furnace, installing the fifth converter and utilizing oxyfuel burners on the ceiling of the reverberatory furnaces. According to the different operational processes in reverberatory, converter and anode furnaces different types of corrosion mechanisms and degradation can be observed in the refractories of copper smelting furnaces. In the case of reverberatory furnaces, the corrosion and degradation of refractories may be factors such as hot corrosion by melt, corrosion attack by the constituents of burning fuel, degradation of sidewalk exposed to mechanical stresses of the feed charge and the hydrostatic pressure exerted by the melt inside the furnace, all of which are due to the unique operational condition governing the reverberatory furnaces environment, i.e. burning fuel atmosphere, charge concentration and combination, furnace temperature, calm melt condition, etc. In the case of converter furnaces, the most likely corrosion and degradation of refractories may be due to the chemical reaction between the melt and degradation of tuyere zones due to sever movement of the melt and mechanical strikes of the punch rod. Also the most essential corrosion reaction occurs around the mouth of the converter because of the mechanical strikes by the cleaning device and thermal heat shock. Other parts inside the furnace are corroded due to the reactions between the fayalite slag and the furnace refractory. In anode furnaces the degradation mechanism is mostly related to the gaseous corrosion (penetration of natural gas or liquid gas inside the refractory structure due to the long period of reduction processes and refining stages. Finally another important factor responsible for destruction of refractories in these furnaces is the copper oxide slag together with the fume constituents of burning fuels.

Jan 1, 2004

By Benoît Plante

La mine Tio (QIT Fer et Titane Inc.) exploite à ciel ouvert un gisement d?ilménite massive depuis 1950, générant jusqu?à maintenant plus de 70 Mt de roches stériles potentiellement génératrices de drainage neutre contaminé (DNC), dont une partie est submergée dans le lac Petitpas, au nord de la mine. Si généralement l?ennoiement des rejets miniers a un effet bénéfique pour limiter la contamination des eaux, cela reste à prouver pour ce qui est des stériles générateurs de DNC. Des essais en réservoirs ont été réalisés afin d?évaluer la réactivité de trois différents types de stériles submergés, qui ont été choisis en fonction de leur teneur en ilménite. Afin d?évaluer l?impact de la matière organique sur la réactivité des stériles submergés, chaque type de stérile est étudié en immersion simple ainsi que combinée à des sédiments prélevés au lac Allard, à proximité de la mine, d?où l?eau utilisée dans les essais a aussi été prélevée. L?évolution des teneurs en Ca, Mg, Si et Ni durant les 8 premiers mois d?étude démontrent que les stériles immergés sont réactifs, mais l?impact de la matière organique demeure pour l?instant difficile à préciser. Tank tests on Tio mine waste rock The Tio mine (QIT Iron and Titanium Inc.) exploits a massive ilmenite ore as an open pit since 1950, producing over 70Mt of potentially contaminated neutral drainage (CND)-generating waste rocks. While the underwater disposal of mine wastes generally show a beneficial effect on water contamination, this method still needs to be approved for CND-generating waste rocks. Tank tests were realized in order to evaluate the reactivity in underwater conditions of 3 different waste rock types, chosen with regards to their ilmenite content. In order to evaluate the impact of organic matter on the reactivity of underwater waste rock, each waste rock type was studied in simple immersion and in combination with sediments sampled at Allard lake, located near the mine, where the water for the tests was also sampled. The evolution of Ca, Mg, Si and Ni during the 8 first months of testing show that the waste rocks are reactive underwater, but the impact of the organic matter is till hard to define.

Nov 1, 2008

By M. X. Yao, C. D. Opris, P. C. Patnaik, R. Liu, X. J. Wu

Two cobalt-based superalloys, Stellite 694 and Stellite 712, were functionally graded with reinforcement of titanium-carbide particle for high-temperature wear/corrosion applications. The designed composite specimens were fabricated using powder metallurgy (P/M) technique, combined with hot isostatic pressing (HIP). Calorimetric effects of the alloy powders were investigated using the differential scanning calorimetry (DSC) technique, which provided the basis of the sintering cycles designed. The phases present in the microstructures of the materials were analyzed using SEM and X-ray diffraction. The wear resistance of the materials was evaluated on a pin-on-disc tribometer. It was demonstrated that adding titanium-carbide particles to the alloys has increased significantly their wear resistance. It was also found that the HIP process had improved the density of the sintered specimens and thus enhanced their wear resistance.

Jan 1, 2004

By J. L. Rodrigues Bravo

The aim of this paper is to show the results of the study that relate the variations of the bismuth content in the Caraíba Metais' electrolytic copper with the main electrolysis' process variables as electrolyte flow rate and temperature, anode's impurities content, electrolyte composition, current density, etc and their combinations and factors like cathode washing, blend of materials entering rod plant's furnace, analytical methods, shot-circuit inspection, etc. Also, the methodology considered arsenic, bismuth and antimony mass balance in the electrolysis and their electrolyte's molar ratio relations as well as bibliographic references of refineries that operate in similar conditions. The results showed the circumstances with the major probability of causing bismuth content increasing in the electrolytic copper and the main operating conditions that have to be fixed for having less bismuth variation and lower content in the electrolytic copper.

Jan 1, 2007

By F. Golestani-Fard, A. A. Nourbakhsh

In this paper microstructural development of nitride-Bonded SIC refractories is reported in presence of Al203, Mg() and Urea additives .The samples were prepared by mixing, shaping and firing at 1400-1500°c in a controlled atmosphere furnace. Phase analysis, microscopic observation and mechanical evaluation were taken for microstructural investigations. The strength of samples doped with Al203 was first increased and then decreased at higher amount of Al2O3 additions. The addition of MgO decreased the strength while the urea showed an improving effect on strength. These phenomena could be attributed to microstructural evolution and mainly to liquid phase formation and grain morphology. It was found that the additives such as Al203, MO and urea could modify the microstructure in terms of phase formation and texture modification, which in terms influences the mechanical behavior.

Jan 1, 2004

By Fengxiang He, T. Meadowcroft, Yanjun Zhang

Slag from the zinc fuming furnaces contains about 3 percent zinc and 0.1 percent lead. The paper outlines several experimental techniques for recovering these components from liquid fumer slag. The simplest method, remelting followed by a hold period, indicated that a substantial fraction of the metal values was recoverable as a result of fuming into the gas phase, presumable by reduction of the metal ions by divalent iron ions. Following on from this, slag samples were equilibrated with copper, chosen because the activity coefficients of zinc and lead in copper are very low. This improved metal recovery, with substantial amounts of lead and zinc reporting to the liquid copper as well as to the fume. Application of an electrical emf across the slag-metal interface, using a graphite anode and a liquid copper cathode, resulted in further gains in metal recovery.

Jan 1, 2004

Owner?s Team and EPCM ?Teams rolesmay vary to suit the skills available, however the tasksremain the same ?Ensure adequate level of capability in the team ?Large owner?s teams vssmall owner?s teams ?size of owner?s teams can reflect not only the individual level of capability but also the type ofrelationship with the EPCM contractor ?Wholly owned projects vsjoint ventures projects ?Both cases require clear accountabilities and authorities ?Project sponsor should be a senior executive with commercial andtechnical accountability of project outcome ?Project leader should be experienced and have solid leadership capabilities ?Attention should be paid to balancing personality types in an owner?s team

May 1, 2010

By D. R. Griffiths

"Oxidation of pyrrhotite prcxiuces sulphuric acid which in turn leaches out heavy metals, resulting in acidic contaminated seepages. The establishment of a marsh on top of the pyrrhotite would result in an anaerobic sediment, which should prevent further oxidation of the pyrrhotite. Initial data indicates that concentrations of sulphates and heavy metals in the seepage water are greatly reduced. Further hydrogeological studies are required however, to determine if metal and acidic loadings to the environment have increased.L'oxidation du sulfure de fer produit de l'acide sulfurique qui a son tour attaque les métaux ayant pour resultat une contamination d'acide et de métal des eaux d'infiltration. L'etablissement d'une couverture faite de boue et de vase au-dessus du depot du sulfure de fer réduit les effets de l'oxidation.Les données initiales indiquent que les concentrations de souffre et de métaux dans les eaux d'infiltration sent grandernent réduites.Des études plus poussées sent nécessaires pour déterminer si les quantités de souffre et de métaux dans les eaux d'infiltration ont augmentées.INTRODUCITONPyrrhotite tailings are readily oxidized through a combination of precipitation and atmospheric oxygen causing acidification of the unsaturated zone above the water table. This reaction is usually catalyzed by the bacteria, Thiobacillus ferooxidans. As the pH decreases, heavy metals become more soluble resulting in contaminated seepages to ground and surface waters.By creating a marshland on top of the pyrrhotite, an anaerobic intermediate layer should form between the organic covering and the tailings, preventing the oxidation process from progressing.In September 1986, Falconbridge Limited implemented a tailing reclamation project that involved creating a marshland on top of pyrrhotite tailings. The following paper will discuss and illustrate the preliminary results obtained during the sampling period of May to September 1987."

Jan 1, 1988

By M. S. Moats

As smelter feeds become more complex, the impurities that ultimately report to electrorefineries are changing. Many of these impurities collect in the electrolyte and must be controlled. As commercial copper electrorefineries look to expand their capacities by increasing their operating current density, the interaction between electrolyte composition and anode passivation can cause operational difficulties. To improve the industry's understanding of the passivation phenomena, the role of electrolyte composition was evaluated using commercial electrorefining anode samples. The electrolyte composition variables examined were copper, acid, nickel, arsenic, chloride, thiourea and glue. Finally, the role of non-commercially utilized additives, such as bromide and polyethylene glycol were studied. From this investigation, electrolyte parameters that inhibit copper dissolution through copper sulfate precipitation, copper oxide stabilization and/or absorbed species lead to accelerated passivation. Species that prevent passivation have the ability to complex cuprous ions. Possible mechanisms for the role of each.

Jan 1, 2007

By T. Cutard, E. Cailleux, F. Nazaret, G. Bernhart

This paper deals with the study of the mechanical behavior in the 20°C-900°C temperature range of refractory concretes reinforced with metallic fibers. Fibers are introduced to improve the damage resistance and to minimize the quasi-brittle behavior of refractory concretes. In some cases, a plastic or ductile like behavior can be obtained. Two approaches are considered in these studies. The first one is based on the micromechanical scale. Main objectives are to understand, quantify and predict the thermomechanical behavior of monofiber microcomposites. Such considerations are helpful to optimize the composite formulation for a better behavior. The second one is based on the macromechanical scale. Main objectives are to characterize and to model the macroscopic thermomechanical behavior of randomly reinforced refractory concretes. A particular attention is firstly paid to the relationships between the microstructural changes and the mechanical properties and secondly to the structural size effects.

Jan 1, 2004

By S. R. Izatt

The use of MRT, a highly selective separations technology, has long been demonstrated to be a cost effective, efficient, and environmentally sound process for extraction of a wide range of anions and cations that are commonly found in copper electro - refining and electro - winning circuits, as well as in environmental treatment operations. This paper provides an update of commercial MRT applications in the copper industry. Several recent installations and test programs are reviewed including recovery of bismuth from tank house electrolyte, and from chloride matrix selenium reduction solution which is generated in the anode slimes treatment process. Recovery and refining of platinum group metals originating in the anode slimes is also discussed. Various other base metal and other target separations of interest to the copper producer are also reviewed. The recovery products are high purity metal salts which can be marketed directly or readily reduced to metal.

Jan 1, 2007

By T. Hartmann

The presence of crud represents a permanent challenge for solvent extraction in the hydro-metal industry. The crud is a stable emulsion which slowly spreads along the phase boundary between the aqueous and organic phase. The crud can significantly impair the efficiency of hydro-metal extraction because the phase boundary between the aqueous and organic phases assumes substantial proportions, and the settlers cannot react flexibly. In a chain reaction, all settlers connected in series become infected with crud. The transfer of organic phase to the electrowining (EW) cell can cause 'cathode burn'. Continuous treatment of the crud is extremely effective and reliable with a 3-phase separating solid bowl centrifuge. All three phases are separated distinctly from one another. All associated process steps exhibit a steady uniform efficiency. First and foremost, they ensure a reliable, continuous extraction process and, second, they recover valuable re-usable organics from the crud.

Jan 1, 2007

By Jorge Amaya

A critical aspect of long-term open-pit mine planning consists in computing a production schedule based upon a block sequencing strategy. Such a schedule should specify when and if blocks should be extracted in such a way as to maximize NPV, while satisfying wall-slope and production capacity constraints. It is well known that this problem can be modeled with integer programming (IP). However, integer programming is not used in practice because the size of typical block models makes such problems intractable to standard IP solvers. In this article we describe a scalable IP-based methodology for solving very large (millions of blocks) instances of this problem. We show that embedding standard IP technologies in a local-search based algorithm we are able to obtain near-optimal solutions to large problems in reasonable time. This methodology has been tested in several mine wide block models.

Oct 1, 2009

By Jorge Amaya

A critical aspect of long-term open-pit mine planning consists in computing a production schedule based upon a block sequencing strategy. Such a schedule should specify when and if blocks should be extracted in such a way as to maximize NPV, while satisfying wall-slope and production capacity constraints. It is well known that this problem can be modeled with integer programming (IP). However, integer programming is not used in practice because the size of typical block models makes such problems intractable to standard IP solvers. In this article we describe a scalable IP-based methodology for solving very large (millions of blocks) instances of this problem. We show that embedding standard IP technologies in a local-search based algorithm we are able to obtain near-optimal solutions to large problems in reasonable time. This methodology has been tested in several mine wide block models.

Oct 1, 2009

By Michel Aubertin

Mining activities can produce large volumes of waste rock, which are typically deposited in piles on the soil surface, above the water table. Such piles can cover areas of several tens of hectares and can reach over a hundred meters in height. For hard rock mines, the waste rock grain size can vary from silty particles to metre-scale blocks. The internal structure of a pile constructed on a relatively flat surface typically includes two main zones. The first zone corresponds to the heart of the pile, and is formed by several sub-horizontal stratifications (with dense and loose layers) due to the heavy mine equipment traffic which induces local compaction and degradation of the waste rock. The second zone corresponds to regions where waste rocks are deposited by push-dumping or end-dumping close to the external flank of the pile, inducing grain size segregation along the slope. Depending on the deposition sequence, grain size distribution and bench height, a gradation may then be observed, with coarser particles (with cobbles and blocks) near the base and finer particles near the crest, together with inclined stratifications due to the advance of the deposition face. These internal features affect the distribution and flow of water (and air) in the pile. To assess the internal distribution of material properties within the pile, a combination of several tools is usually required which can provide information on the hydrogeological and geochemical characteristics of the waste rock. In this regard, geophysical tools are very interesting because they can lead to a threedimensional mapping of property variations. The information gathered from a combination of appropriately selected techniques can be used to construct numerical models to further study unsaturated water flow and reactive transport. Such simulations help better understand the pile response in its actual and future states, which in turn provides input to adjust the deposition sequence, to plan for closure, and to select an in situ groundwater monitoring strategy. The presentation will give an overview of techniques that have been developed to characterise material properties in the laboratory and in the field, and to obtain a general picture of a pile?s internal structure. Additional results on unsaturated reactive transport modelling will also be shown to illustrate how the internal pile structure may influence its hydro-geochemical and environmental response.

Nov 1, 2008

By G. Portillo

Electrospark Deposition (ESD) is a pulsed-arc micro-welding process characterized by using high current electrical pulses, of a short duration, to deposit an electrode material on a metallic substrate. The short duration of the electrical pulse allows for a low heat input over the substrate and an extremely rapid solidification of the deposited material. As a result, the ESD is capable of a wide variety of microstructures like micro-segregationfree solid solutions, nanostructured grains, metastable structures, and amorphous phases. The present work shows a microstructural analysis of rapidly solidified Al-Ni alloys coatings by the ESD process. Field Emission Scanning Electron Microscopy (FE-SEM) and X-Ray Diffraction (XRD) were performed to present the microstructural evolution as a function of the welding parameters. The phases and non-equilibrium metastable structures present in the alloys, and their distribution, were found to be a sensitive function of the alloy composition; hence its formation is governed primarily by thermodynamic considerations.

Jan 1, 2011

By A. Jain

During sheet forming, metal experiences not only multi-axial load, it also undergoes strain path changes. For example, metal in the flange region may be drawn, may bend and unbend through a bead, before bending around a die radius, etc. Compression data were obtained from AZ31 sheet after pre-straining in compression along an orthogonal direction. The compression directions correspond to the sheet product (rolling-RD, transverse-TD, and normal-ND) directions. Three cases are examined: slip dominated deformation (ND) followed by twin dominated (RD or TD) deformation, twin dominated (RD or TD) followed by de-twinning (ND), and twin dominated (e.g. RD) followed by cross-twinning or secondary twinning (e.g. TD). Slip induced pre-straining simply hardens the material, while twin dominated pre-straining alters the texture allowing the material to either de-twin or re-twin upon changing the strain path. Polycrystal plasticity modeling has been used to predict qualitative features of the flow curves during strain path changes.

Jan 1, 2006