Search Documents

By M. J. Hadianfard

The effect of holding at temperature on fatigue life of a 10 vol% particulate SiC reinforced Titanium alloy has been investigated. The influence of holding time at 600°C on fatigue of this material has been studied by using tension-compression tests, scanning electron microscope and image analysis. The specimens were heated to 600°C by using a controlled atmosphere furnace; hold at this temperature for time ranging from 0 to 100 hours, and then fatigue tested at room temperature under controlled constant plastic strain. The number of cycle to failure found to decrease with increasing of the holding time. In addition the fracture mechanism and number of debonded particles has been significantly influenced by holding time at 600°C.

Jan 1, 2004

By E. Paransky, M. Rigaud, G. Paschek, S. Palco

Some of the negative impacts of carbon addition on the strength of castables are yet to be overcome in order to fulfill its potential benefits for oxidation resistance. This paper reports the results of recent studies conducted at CIREP on the effects of different types of carbon additives on the thermo-mechanical properties of magnesia-based castables. Experimental techniques included measurements of the hot modulus of rupture (HMOR), hot modulus of elasticity (HMOE), as well as the wedge-splitting test (WST). The comparison of evolving microstructures was carried out employing scanning electron microscopy with microanalysis attachment (SEM/EDS) and X-ray diffraction (XRD). HMOR values of 12 MPa at 1300°C have been reached in MgO-Si02-C castables containing up to 7% carbon.

Jan 1, 2004

By W. Lo, M. Brothers, G. Oprea, G. Richard, T. Troczynski

Magnesia-chrome and chrome-magnesia are the most used refractories in contact with iron-rich non-ferrous smelting slags. The corrosion by slag always brings chromium oxide into the slag, causing the precipitation of crystalline phases at the process temperature. This secondary effect of the chromium-bearing refractory dissolution was studied in this work, emphasizing the effect of the other chemical components of the slag at various temperatures. The experimental results showed that the presence of chromium and lead contribute, although in different ways, to the formation of complex spinel phases and their precipitation at temperatures in the range of 1250-1400°C. The XRD and SEM/EDS results were discussed for refractory-slag mixes containing 0-20% Cr2O3 and 0-11% PbO.

Jan 1, 2004

By D. Allen

Faced with decreasing ore grades and harder ores, many mines today are forced to become more efficient with their approach to processing. Variability in ore hardness, mineral liberation, reagent consumption, sliming, and leach responses are all a function of the minerals present and their concentration. Modern semi-automated X-ray Diffraction (XRD) analyses using Rietveld refinement techniques, in conjunction with high speed quantitative Near Infrared (NIR) analyses, provide reliable quantitative mineralogical ore profiling. By the implementation of XRD with NIR, mining, milling and leaching operations no longer need to be dependant on visual estimates for GeoMetallurgical Modeling and are provided with a valuable forecasting and production control tool. This paper will illustrate the development, plant implementation and application of XRD and NIR at several copper operations.

Jan 1, 2007

By S. D. Logan

This presentation describes a lightweight automobile body structure concept developed at DaimlerChrysler to support a high fuel-efficiency vehicle project. This body structure consisted primarily of large thin-wall magnesium castings and resulted in a more than 40% weight reduction with a minimal cost increase over a conventional steel structure while achieving significantly improved structural performance as evaluated through CAE simulations. One concept vehicle was built for the purpose of demonstrating concept feasibility. Several slides showing the prototype build process are presented. The presentation also describes several large thin-wall die casting body applications that are in current production or have been used in recent production automotive applications and identifies areas where further development could improve the chances of a magnesium intensive body structure becoming a production reality at a later time.

Jan 1, 2006

By R. Ham-Su, J. P. Healey, S. P. Farrell, R. S. Underhill, M. A. Gharghouri, C. V. Hyatt, L. M. Cheng

Magnetic shape memory alloys (MSMA's) are a class of materials where magnetic energy can be converted into mechanical energy and vice versa. NiMnGa-based MSMA's have attained magnetic field induced strains up to approximately 10% and have a relatively wide operating temperature range, from well below 0°C to above RT, making them very attractive for a variety of applications. However, these materials also suffer from low toughness. Using these materials in a composite could mitigate this shortcoming, and also overcome limits imposed by inertia and eddy current losses. In this work, we describe the manufacture and characterization of such composites. Composites with 30% by volume MSMA were fabricated under a magnetic field resulting in anisotropic magnetic properties. Damping properties were evaluated by dynamic mechanical analysis.

Jan 1, 2004

By S. Orzecki

The KGHM Copper Refinery Plant, Glogów 1, has operated for 35 years and -increased its capacity almost ten times.Cathode quality, expressed in terms of the total impurity content, has undergone a five-fold improvement. The present refining capacity is equivalent to 240,000 metric tonnes of copper cathode, with a total impurity content of 20 ppm, inclusive of 10 ppm Ag. These accomplishments result from combined implementation of current technological progress in electrolytic refining and KGHM's own solutions applied to the Glogów Refinery. The quality improvement measures feature both lowering actual current density, despite an increase in nominal current density, and diminishing the role of non-ion mechanisms which transfer impurities to cathodes. The paper contains a detailed discussion of these issues and outlines possible measures aimed at further production and quality improvements.

Jan 1, 2007

By M. Özer, F. Boylu, G. Önal

In this study, the fine coal waste subjected to the experiments is taken from the waste stockpile of Soma Coal Plant. The possibilities of its evaluation and the production of clean coal were investigated. For this purpose, Reichert Coal Spiral and Shaking Table are used. The minus 1 mm coal waste includes 60.43% ash and 50% minus 38 micron material by weight. The microscopic observations of the screen fractions were shown that the clay minerals are in fine sizes and the coarser size fractions contain silica and carbonate minerals as ash forming materials. The tests were conducted after desliming. The commercial grade clean coal product containing 29-35% ash with a calorific value of 3800-4200 kcal/kg (15.91-17.58 MJ/kg) was obtained by gravity methods.

Jan 1, 2004

By W. T. Thompson, S. Durham, K. M. Jaansalu

The role of platinum on the relative stability of gamma - gamma prime equilibrium is only qualitatively known, and may bear upon the stability of a superalloy under a protective coating. The binary phase diagrams Ni-Pt and Al-Pt, and the Ni-rich corner of the Ni-Al-Pt ternary, are reviewed and simple self-consistent thermodynamic models are derived. These thermodynamic models are incorporated into a database used to predict the gamma-gamma prime equilibrium for single crystal superalloys. In small concentrations, platinum is predicted to increase the temperature stability, but not the proportion, of the gamma prime phase over the gamma phase in third generation alloys such as CMSX-10. Another effect of platinum addition is to significantly lower the solidus temperature. These findings are compared to experimental data in the literature.

Jan 1, 2004

By M. Solomon

Abstract -Giant, sediment-hosted lead-zinc deposits in northern Australia formed during development of Mid-Proterozoic extensional basins that overlie Lower Proterozoic basement. The basement in the Mount Isa area, exposed by folding and faulting, contains fractionated, high-heat-producing granites. These granites generate heat at a rate of about 6 ?Wm-3, probably sufficient to form giant lead-zinc deposits either by (a) driving episodic convection of saline basement and basin fluids for periods of 105 to 106 years at temperatures of about 230°C, or (b) heating basin fluids moving under the influence of topographic relief or fault movement. The presence or absence of such granites may form a vital component of the genetic model. Ore-forming fluid flow was probably initiated by continent-scale, extensional basin fracturing.

Jan 1, 1992

By S. Theobald

Semi-finished copper and copper-alloy products are typically produced by casting, subsequent hot rolling or extruding and further cold working by rolling and drawing. The technological properties of the products depend not only on the chemical composition of the alloys but also on process parameters such as annealing conditions and degree of deformation. In each production step, measuring and control technology is an important tool for optimizing processes and ensuring constant high quality. This paper follows the product all the way from testing incoming scrap packages, chemical analysis of melts, mould level control in casting, non-destructive testing technologies in cold forming processes, controlling geometrical properties in the production process, to the final tests of technological properties. All test methods are focused on the applications and requirements of our customers, as the examples show.

Jan 1, 2007

By Marta Polgari, Eva Surova, Bohumil Molak

Abstract -The Ûrkút rhodochrosite deposit and Branisko Mn showings (rancieite, manganiferous calcite), located in Lower Jurassic marine sedimentary rocks with black shale, were studied by organic­ geochemical methods. Both depositionallocalities were affected by the Lower Jurassic Toarcian anoxic event. Ûrkút shales are rich in organic matter (av. 2.94 wt% total organic carbon), the composition of which indicates derivation mainly from marine sources, with some terrigenous component. The shales matured in a bacterially active environment under reducing conditions of diagenesis-catagenesis. Branisko shales (?0.2 wt% TOC) with lenses of Mn oxide ore were weakly metamorphosed and their organic matter thermally degraded. The model for Mn carbonate ore formation envisages reaction of Mn derived from sediments, with carbonate generated by a bacterially mediated process of decom­ position of organic matter that also involved Mn reduction.

Jan 1, 1992

By Andreea Catalina Gluhoi

Oxidation and reduction reactions of N-containing molecules have been studied over different types of gold-based catalysts, Au/MOx/Al2O3 and Au/MIOx/MIIOx/Al2O3 (M, MI, MII=Li, Rb, Mg, Ce, Zr, Mn, Cu) prepared by deposition precipitation with urea. In general, all the catalysts were already active at low temperatures. NH3 oxidation was effectively catalyzed by Au/CuO/Al2O3, a catalyst which also gives the highest yield in N2. NO reduction by H2 performed over gold-based catalysts produced N2O, N2 and NH3 and N2O reduction resulted in the formation of dinitrogen. For all the reactions, large synergistic effects have been obtained by addition of different kind of additives.

Oct 1, 2003

By G. Plascencia, A. Warczok, M. Zamalloa, T. Utigard, N. Behnood

The objective of this investigation was to investigate interactions between high-grade copper mattes and Rexal 60DB direct bonded basic bricks. The infiltration and attack of Rexal 60DB bricks by copper matte and continuous converter matte was investigated in laboratory tests at temperatures up to 1300 °C. The brick dissolution and infiltration tests did not show any significant difference between the 70% Cu and the 81% Cu mattes. More metallic copper was visible in the pores in the case of 81% Cu matte. An important mechanism for direct-bonded magnesia-chrome brick destruction is that oxysulphides start to infiltrate the brick, followed by slow oxidation of the matte producing metallic copper and cuprous oxide, which then react with MgO and Cr2O3, primarily attacking the direct bonds of the brick.

Jan 1, 2004

By Eva Surová, Molák. Bohumil, Márta Polgári

The Úrkút rhodochrosite deposit and Branisko Mn showings (rancieite, manganiferous calcite), located in Lower Jurassic marine sedimentary rocks with black shale, were studied by organicgeochemical methods. Both depositional localities were affected by the Lower Jurassic Toarcian anoxic event. UrkUt shales are rich in organic matter (av. 2.94 wtOJo total organic carbon), the composition of which indicates derivation mainly from marine sources, with some terrigenous component. The shales matured in a bacterially active environment under reducing conditions of diagenesis-catagenesis. Branisko shales (~0.2 wt % TOC) with lenses of Mn oxide ore were weakly metamorphosed and their organic matter thermally degraded. The model for Mn carbonate ore formation envisages reaction of Mn derived from sediments, with carbonate generated by a bacterially mediated process of decomposition of organic matter that also involved Mn reduction.

Jan 1, 1992

By A. Rahimi

The smelting plant at Sarcheshmeh Copper complex commenced working with two reverbatory furnaces, four pierce smith converters, two anode furnace and one holding furnace having a known capacity of 420 metric tons of anodic copper according to the initial design in 1982 (1361 Iranian calendar). During the period from the commencement date up until now, the smelting plant has undergone changes for improvement and enhanced production by substituting holding furnace with another anode furnace, installing the fifth converter and utilizing oxyfuel burners on the ceiling of the reverberatory furnaces. According to the different operational processes in reverberatory, converter and anode furnaces different types of corrosion mechanisms and degradation can be observed in the refractories of copper smelting furnaces. In the case of reverberatory furnaces, the corrosion and degradation of refractories may be factors such as hot corrosion by melt, corrosion attack by the constituents of burning fuel, degradation of sidewalk exposed to mechanical stresses of the feed charge and the hydrostatic pressure exerted by the melt inside the furnace, all of which are due to the unique operational condition governing the reverberatory furnaces environment, i.e. burning fuel atmosphere, charge concentration and combination, furnace temperature, calm melt condition, etc. In the case of converter furnaces, the most likely corrosion and degradation of refractories may be due to the chemical reaction between the melt and degradation of tuyere zones due to sever movement of the melt and mechanical strikes of the punch rod. Also the most essential corrosion reaction occurs around the mouth of the converter because of the mechanical strikes by the cleaning device and thermal heat shock. Other parts inside the furnace are corroded due to the reactions between the fayalite slag and the furnace refractory. In anode furnaces the degradation mechanism is mostly related to the gaseous corrosion (penetration of natural gas or liquid gas inside the refractory structure due to the long period of reduction processes and refining stages. Finally another important factor responsible for destruction of refractories in these furnaces is the copper oxide slag together with the fume constituents of burning fuels.

Jan 1, 2004

By Benoît Plante

La mine Tio (QIT Fer et Titane Inc.) exploite à ciel ouvert un gisement d?ilménite massive depuis 1950, générant jusqu?à maintenant plus de 70 Mt de roches stériles potentiellement génératrices de drainage neutre contaminé (DNC), dont une partie est submergée dans le lac Petitpas, au nord de la mine. Si généralement l?ennoiement des rejets miniers a un effet bénéfique pour limiter la contamination des eaux, cela reste à prouver pour ce qui est des stériles générateurs de DNC. Des essais en réservoirs ont été réalisés afin d?évaluer la réactivité de trois différents types de stériles submergés, qui ont été choisis en fonction de leur teneur en ilménite. Afin d?évaluer l?impact de la matière organique sur la réactivité des stériles submergés, chaque type de stérile est étudié en immersion simple ainsi que combinée à des sédiments prélevés au lac Allard, à proximité de la mine, d?où l?eau utilisée dans les essais a aussi été prélevée. L?évolution des teneurs en Ca, Mg, Si et Ni durant les 8 premiers mois d?étude démontrent que les stériles immergés sont réactifs, mais l?impact de la matière organique demeure pour l?instant difficile à préciser. Tank tests on Tio mine waste rock The Tio mine (QIT Iron and Titanium Inc.) exploits a massive ilmenite ore as an open pit since 1950, producing over 70Mt of potentially contaminated neutral drainage (CND)-generating waste rocks. While the underwater disposal of mine wastes generally show a beneficial effect on water contamination, this method still needs to be approved for CND-generating waste rocks. Tank tests were realized in order to evaluate the reactivity in underwater conditions of 3 different waste rock types, chosen with regards to their ilmenite content. In order to evaluate the impact of organic matter on the reactivity of underwater waste rock, each waste rock type was studied in simple immersion and in combination with sediments sampled at Allard lake, located near the mine, where the water for the tests was also sampled. The evolution of Ca, Mg, Si and Ni during the 8 first months of testing show that the waste rocks are reactive underwater, but the impact of the organic matter is till hard to define.

Nov 1, 2008

By M. X. Yao, C. D. Opris, P. C. Patnaik, R. Liu, X. J. Wu

Two cobalt-based superalloys, Stellite 694 and Stellite 712, were functionally graded with reinforcement of titanium-carbide particle for high-temperature wear/corrosion applications. The designed composite specimens were fabricated using powder metallurgy (P/M) technique, combined with hot isostatic pressing (HIP). Calorimetric effects of the alloy powders were investigated using the differential scanning calorimetry (DSC) technique, which provided the basis of the sintering cycles designed. The phases present in the microstructures of the materials were analyzed using SEM and X-ray diffraction. The wear resistance of the materials was evaluated on a pin-on-disc tribometer. It was demonstrated that adding titanium-carbide particles to the alloys has increased significantly their wear resistance. It was also found that the HIP process had improved the density of the sintered specimens and thus enhanced their wear resistance.

Jan 1, 2004

By J. L. Rodrigues Bravo

The aim of this paper is to show the results of the study that relate the variations of the bismuth content in the Caraíba Metais' electrolytic copper with the main electrolysis' process variables as electrolyte flow rate and temperature, anode's impurities content, electrolyte composition, current density, etc and their combinations and factors like cathode washing, blend of materials entering rod plant's furnace, analytical methods, shot-circuit inspection, etc. Also, the methodology considered arsenic, bismuth and antimony mass balance in the electrolysis and their electrolyte's molar ratio relations as well as bibliographic references of refineries that operate in similar conditions. The results showed the circumstances with the major probability of causing bismuth content increasing in the electrolytic copper and the main operating conditions that have to be fixed for having less bismuth variation and lower content in the electrolytic copper.

Jan 1, 2007

By F. Golestani-Fard, A. A. Nourbakhsh

In this paper microstructural development of nitride-Bonded SIC refractories is reported in presence of Al203, Mg() and Urea additives .The samples were prepared by mixing, shaping and firing at 1400-1500°c in a controlled atmosphere furnace. Phase analysis, microscopic observation and mechanical evaluation were taken for microstructural investigations. The strength of samples doped with Al203 was first increased and then decreased at higher amount of Al2O3 additions. The addition of MgO decreased the strength while the urea showed an improving effect on strength. These phenomena could be attributed to microstructural evolution and mainly to liquid phase formation and grain morphology. It was found that the additives such as Al203, MO and urea could modify the microstructure in terms of phase formation and texture modification, which in terms influences the mechanical behavior.

Jan 1, 2004