Search Documents

By Guichao Wang, Geoffrey M. Evans, Graeme J. Jameson

"In this paper we present a new method for studying the detachment of particles from bubbles in a rotating turbulent eddy. The eddy is formed in a wall cavity in a two-dimensional water tunnel with transparent walls. When water flows through the tunnel, a vortical flow field develops in the cavity. The properties of the eddy can be modulated by changing the free-stream velocity of the water in the tunnel. Bubbles are pre-loaded with one or more particles in a fluidized bed flotation device located beneath the vortex cavity. Loaded bubbles are released one at a time into the cavity, and the motion of the bubbleparticle aggregate is studied using a high-speed video camera. The diameters of the particles and the bubbles, and the number of particles initially attached to the bubble, can be varied. The trajectories taken by the bubbles are quite complicated. In some cases, the bubble moves to the centre of the eddy, and particles rotate around its axis. If the rotational speed is sufficient, particles may detach due to centrifugal force. However, other modes were observed, including inertial detachment due to rapid changes in direction of the surface of the bubble, because of changes in trajectory of the bubble as a whole, or because of pulsations and oscillations of the bubble surface. Clusters of bubbles held together by particles were seen to form and reform. In the traditional explanation for the detachment of particles in flotation cells, it is assumed that particles detach from bubbles rotating in an eddy due to centrifugal force (Schulze, 1977). Although the conditions assumed in Schulze's theory may exist, it is only one of a range of phenomena that can lead to the detachment of particles from bubbles in a turbulent vortex.INTRODUCTIONThe recovery of particles by flotation methods is dependent on the particle size. The recovery in the existing flotation machines reaches a peak for particle size, typically in the range of 20 to 100 µm. This size range varies as a function of the particle’s properties (type and composites). For coarser particles, the recovery drops very quickly (Gaudin, Groh & Henderson, 1931; Jowett, 1980). If the upper size limit can be increased for flotation, dramatic savings in the grinding energy can be achieved."

Jan 1, 2016

By A. Ghasemi

An alumina-silica coating was deposited on a nickel substrate by sol-gel process, and the structures and composition were evaluated, The sols were made from aluminium and silicon alkoxide, and an acid catalyst including HCl, To produce adherent silica coatings on nickel, various additives such as surfactant, viscose additive and drying control chemical additives were introduced to the system, and appropriate drying and firing cycles were applied after dipping in solution. The hot corrosion and oxidation resistance of the coating at different temperatures were investigated, The structure and uniformity of the coatings were examined by scanning electron microscopy (SEM), The results indicate that a uniform coating of alumina silica can be produced on a nickel substrate by optimizing the composition and process variables of the sol. Coatings can protect substrates from oxidation and hot corrosion at different temperature up to 1000°C, but is not very effective for hot-corrosion resistance at 1000°C.

Jan 1, 2005

By Michael L. Free, Shukla. Abhijeet

The short-circuiting tendency of a copper electrowinning cell (EW) based on the roughness of cathode deposits was investigated with varying parameters such as Cu concentration, guar concentration, current density, and temperature. A bench scale EW cell was set up to produce copper under conditions similar to industrial Cu EW. In addition, a statistical analysis and finite element analysis were performed to analyze the deposited thickness, surface roughness and maximum feature height. Interaction data for the cathode deposits suggest that current density and Cu concentration together affect the roughness of deposit more than the combined effect of guar and temperature. Model predictions of roughness were similar to experimental values. The predicted time to short-circuiting was similar to the measured time. This study provides an industrial relevant baseline against which new operating parameters can be compared.

Jan 1, 2014

By P. H. Shipway, D. G. McCartney, H. Saghafifar

The microstructural changes during thermal ageing at 650ºC in the interfacial region of Alloy 625 weld overlay on a 2.25Cr-1Mo steel was evaluated. Optical microscopy, scanning electron microscopy in SE and BSE modes, electron probe microanalysis and hardness mapping were used to characterize as-welded microstructure and its changes during thermal ageing and precipitates of interfacial region. Carbon migration across the interface was recognised as a major issue. A region of 300 µm wide adjacent to the fusion line, which was found harder in the as-welded condition decarburized during thermal exposure. Studies revealed that this region transformed to a soft region containing large ferrite grains and micron-sized carbides. In the weld overlay, a 50 µm wide hard band (over 650 Kgf mm-2) adjacent to the fusion line formed and carbide precipitates were observed along grain boundaries. Carbide precipitation mostly occured in the 150 µm wide region close to fusion line.

Jan 1, 2017

By SeyedBijan Mahbaz

Development of Geomechanical Earth Models (GEM) is a prerequisite to reservoir management, involving issues such as stress path analysis, prediction of induced seismicity and sanding initiation, and coupled flow-stress modeling that leads to more realistic predictions of oil rates and rock response. Part of GEM development is the stipulation of the 3-D lithostratigraphic disposition (geometry) which is used to choose the geomechanical units. The digital geological model is then populated with quantitative and semi-quantitative data on rock properties, fluid properties, saturations, initial conditions (p, T, [_]) and other information. Both fluid and solid properties are needed this requires integration of geomechanics skills with geophysical and rock physics skills, and this article deals with a subset of this integration process, with an example from two wells in southwest Iran.Rock physics approaches are used to predict reservoir rock and fluid properties with wellbore and 3-D seismic data, which are also used to interpolate rock mechanics properties to the inter-well regions. The first step in a generic rock physics approach is diagnostic and involves the introduction of a suitable Rock Physics model.Acoustic impedance (AI), shear impedance (SI), and density (_) are the fundamental rock properties usually derived using AVO equations, and these parameters, along with attenuation coefficients, can then be correlated to static rock mechanics properties that define deformability and perhaps even strength. In this study, Poisson Impedance is introduced as a new seismic attribute used for lithology and fluid differentiation in the FahliyanFormation (reservoir rock) in two oil wells in the southwest of Iran. To do this, a novel rock physics model was developed for this naturally fractured carbonate reservoir.Currently, these data are also being used to correlate to a limited rock mechanics data base to develop a more extensive GEM to serve as input to more general geomechanical and reservoir modeling tasks.

Jun 1, 2012

By Rene Klymowsky, Norbert Patzelt, Egbert Burchardt, Johann Knecht

"The challenge of ""ore bodies getting steadily harder and lower in grade"" was brought to light during the first oil crisis in the 70's. Shortly afterwards, HPGRs appeared on the scene with the promise of saving energy. This combined with developments in wear protection for the rolls ushered in a period of trade-off studies that considered the HPGR as an option to improve project economics or to even make projects feasible at all.Since then, applications of HPGRs at Cerro Verde (Freeport), PTFI Grasberg (Freeport), Mogalakwena (Anglo Platinum), Tarkwa (Goldfields), Boddington (Newmont), Penasquito (Goldcorp), and others have contributed to the creation of a formidable basket of operating experience. Collected through years of successful operation, this information has been used to validate design criteria, scale-up factors and establishing a clearer picture of what ""to do"" and what ""not to do"".This paper compares results from various mining operations using HPGRs in their processing plants. Some of the lessons learnt in different operating environments are reviewed in order to support proper implementation and operation of HPGR's. Some of the development programs that have been initiated to improve wear life of the tyres and to reduce overall operating costs are reviewed. It is timely to summarize today’s experience and analyse its implications for existing and new operations"

Jan 1, 2012

By A. Bouajila1

Minerals processing organisations will be more and more under intense competitive pressure. Major changes are being experienced with intense respect to resources, processes, production strategies and markets. As result of international competition, only the most productive and cost-effective operations will survive. That is why operators in the minerals industry have always aimed to obtain better performance from their processes along the mineral extraction cycle starting from exploration up to the smelting step if any. A principal ingredient and perhaps the most important one in the process of evolution toward improved productivity is the achievement and implementation of an error-free production synonym of an ignorance-free operation. This is, at the same time, a guarantee for quality, a minimising factor for waste materials production, handling and disposal, and a maximising factor for labour utilisation. The notion of ?error or ignorance-free? -usually identified as a ?made in Japan? manufacturing mythology, will sound, at first impression, like a pious ideal, to be striven for but impossible to attain. Nevertheless, the introduction of measurement and detection technology in the minerals industry along the last century should benefit from the today?s sensors and control systems that explosively expanded beyond their traditional production base into far-ranging commercial ventures. The fastness and spread of those technologies will play an important role in the survival of innovative plants. Their role in information assimilation, and control of operations to maintain an error-free production environment, will help many plants to stay effective on their competitive course. In this paper the feasibility of the zero process ignorance concept as applied to the comminution circuits will be discussed and the challenge behind this ambitious move toward improved productivity will be outlined. Examples of pre-competitive R&D projects started at COREM in order to fulfil this prerogative will be presented.

May 1, 2001

Strips of AA6111 automotive alloy were cast on a horizontal single belt strip casting simulator, Pure copper and carbon steels substrates plasma sprayed with different coatings for improving the strip surface quality, were used as chill moulds, Experimental studies revealed that a graphite coating provided the greatest benefit in achieving good surface quality. The interfacial heat fluxes during solidification of AA6111 strip were calculated by the IHCP method (Inverse Heat Conduction Problem). Temperature variations and cooling rates within the strips were then calculated through numerical simulations based on the time-dependent heat fluxes obtained by IHCP, The effects of casting parameters, including casting temperature and strip thickness, on interfacial heat fluxes, cooling rates and microstructures, were investigated, Although the maximum interfacial heat fluxes on the chill copper substrate were much higher than the results obtained from the steel substrates, the solidification times of the melts were mainly determined by strip thickness. Very fine equi-axed grains were obtained for both 1.2mm and 2.5mm thick strips thanks to the rapid extraction of heat, and effective grain refinement.

Jan 1, 2005

By S. Fabich

Since the very beginning of Polish copper mining, special consideration of sink shaft techniques through highly saturated Cenozoic rocks was required. Shaft freezing has been chosen as a method to consolidate these rocks. Due to the rock mass structure and water inflow potential, shaft sinking without freezing was considered dangerous. In the course of time, rock mass freezing technology and experience were evolved and this technology became safer and more reliable. New techniques appeared not only in the technical method of freezing, but also in the matter of designing. Computer aided techniques allow engineers to make a detailed analysis and view of freeze wall development. Nevertheless it is important to determine basic thermal rock properties. In this paper, the evolution of knowledge and engineering experience taken in Polish copper mines and current knowledge level in that matter were shown.

Aug 1, 2013

By W. G. Jewitt

Introduction The use of the aeroplane in prospecting is already familiar to everyone connected with the mining industry. Apart from transportation companies, three organizations, the N. A. M. E., the Dominion Explorers, and the Exploration Department of the Consolidated Mining and Smelting Company, have made the aeroplane an everyday feature in every mining district in Canada. Its use has been demonstrated successfully in the mountains of British Columbia, but perhaps its greatest field lies in the Canadian Shield, where the numerous lakes and rivers afford an almost continuous series of landing places for aeroplanes, on floats in the summer and on skis in the winter. To the man who has travelled by canoe, toiling over fly-infested portages or held for days at a time, wind-bound, on the big lakes, the ease, speed, and cheapness of aeroplane travel have marked the beginning of a new era, in which ground previously covered with difficulty in a month or more is travelled with ease in a few hours. Development of an air service in the Consolidated Mining and Smelting Company has proceeded on different lines from those of other organizations, and this paper is concerned with that development.

Jan 1, 1931

From 1999 to 2008 rock related accidents accounted for 75 fatalities, nearly 6,000 injuries and almost 14,000 incidents (Pappas and Mark, 2011). Clearly this shows that rock related safety on coal mines remains a serious issue and more effort is needed to address this hazard. This paper reviews support design considerations and monitoring needed to improve rock related safety in room and pillar coal mines in the USA. From the present study design considerations continue to evolve and improvements in technology and a better understanding of failure mechanisms and methods to prevent these failures from occurring are in place. At first glance, the design of safe and efficient underground openings appears simple until the designer begins to realize the complexities and variability of geometries, geology, loading and stress influences, support designs and other factors such as corrosion and economics. Ultimately the goal of all designs is to ensure that it can be completed safely, last for the duration of the design life and it is economically feasible.

Aug 1, 2013

By W. D. Mulholland

"I ASSUME that any effort on my part to deal with the question of the importance of the mining industry is going to be largely an exercise in preaching to the converted, but there are one or two aspects that I'd like to particularly mention.The first is that, in terms of almost all factors, the mining industry is a very important industry in Canada. It is important in terms of employment in relation to the gross national product of Canada and it is particularly important in the international trade of Canada. So far from being insignificant domestically, it is also an extremely important factor in the international picture. That's an important point to bear in mind, because as we talk about all the other matters we never can lose sight of the fact that mining management always has to be conscious of its international competitive position. It is something that one forgets at one's peril, and to a somewhat greater extent than is true of many other industries, those managements have to compete in an international context for their markets, to some extent for their people for specialized skills and of course for finance. In the evolution of domestic policies it is a very, very perilous step to take to impair that competitive ability of the domestic mining industry."

Jan 1, 1972

By S. M. Fatemi-Varzaneh

The AZ31 magnesium alloy is considered as a promising alloy in various applications and industries. Furthermore, to design a proper hot working process (rolling, forging and extrusion), the assessment of hot working behaviour of the alloy is necessitated. Accordingly, the hot deformation behaviour of AZ31 alloy was studied through hot compression testing method. The latter was carried out in a wide range of temperature (523 K to 783 K) and strain rates. The obtained true stress-true strain curves and final microstructures were examined and a partial melting was realized at 740 K. It was concluded that the presence of liquid did change the deformation mechanisms thereby affecting the flow behaviour.

Jan 1, 2005

By M. A. N. Rosa, L. C. R. Machado, R. A. Fonseca, A. M. Mendonça

"Sossego Mine was the first Vale SAG mill operation to process copper-gold ore. It is located in the state of Para, in the south-eastern Amazon region of Brazil. In the first six years of continuous operation, Vale investigated different alternatives for improving circuit performance by investigating operating conditions, mainly focusing on the SAG mill.Today, after a steady increase over five years the annual production rate seems to have stabilized. It is hoped this work will show how the SAG operating practice have been perfected with time and as new data are collected. Historical data of mill grind-outs and crash stops helped create operation curves depending on the ball charge volume and total charge volume. Also noted were impacts on throughput due to the effect of reducing liner weight and the ore type characteristics."

Jan 1, 2012

By W. S. Urbanski, A. L. Devernoe, R. W. Stuart, M. S. Walker

"Although many investigators have successfully achieved separations using variations of a concept wherein particles are buoyed upwards against gravity in a magnetically attracted fluid, none have succeeded in separating fine particles in a manner that is practical tor mineral beneficiation. This paper describes laboratory tests and preliminary economic analyses for a new mineral separation process which provides enhanced magnetic buoyancy and separation capabilities. The process provides a means of gravity separation in a regime where conventional gravity separation is inadequate; that is for small differences in mineral densities and for very fine particles. Although early interest centers on gravity separation, the process has also been successfully used for precise magnetic separation.Tests were conducted on a variety of mineral mixtures, ore samples and concentrates including; a sphalerite ore, pyrochlore ores and concentrates, cassiterite pre-concentrates, a chromite pre-concentrate, and heavy mineral placer samples. Separations requiring high discrimination between fine particles narrowly different in density or weak magnetic properties were obtained. Of particular interest is the ability of the process to concentrate or remove oxide minerals or gangues, especially silicates. Potential applications are discussed."

Jan 1, 1985

By C R. Evans

Whole-rock and muscovite potassium-argon dates from selected low-grade metamorphic rocks of Precambrian age in the Canadian Rocky Mountains near Jasper, Alberta, were obtained to ascertain the age of the source terrain and the age of the metamorphism. Ten argillites gave whole-rock dates ranging from 270 to 485 million years, dates which are apparently inter-mediate between the age of the source material and that of the metamorphism. "Up-dating" increases with the degree of orientation of muscovite in the cleavage plane, and with the ratio of the muscovite in the cleavage plane to that in the plane of the bedding. Detrital muscovite from four arenaceous rocks gave dates ranging from 1,050 to 1,780 million years. "Updating" increases with decreasing grain size, so that, within the range investigated, the cube of the median diameter (¢) of the muscovite is apparently proportional to the radiometric date.

Jan 1, 1964

By E. Cauda, K. Phillips

"Diesel particulate matter (DPM) exposures are a serious occupational health hazard in underground mines. While the complex nature of DPM makes direct analysis difficult, its primary component, elemental carbon (EC), can be used as surrogate. The near real-time FLIR Airtec monitor measures EC mass based on laser extinction. It was developed for use in underground metal/non-metal mines, and calibrated to the NIOSH Method 5040. Its effectiveness has not been demonstrated in coal mines, however, where coal-sourced EC could produce analytical interference. To gain preliminary insights regarding the Airtec’s performance in the presence of coal dust, experiments were conducted in a controlled laboratory chamber. The Airtec EC results consistently underestimated Method 5040 EC for both respirable-sized and submicron coal dusts. While underestimation of coal-sourced EC bodes well for limiting coal interference for DPM measurement, one key reason for the observed trend was non-uniform coal particle deposition on the Airtec filter. This may be problematic in coal mines where DPM and coal dust occur together in the instance that DPM deposition is also non-uniform. INTRODUCTION Diesel particulate matter (DPM) is an occupational health hazard, and underground miners have the potential for relatively high exposures due to their work in confined environments with large diesel equipment (NIOSH, 2011). DPM is heterogenous and complex in terms of its chemical composition (Birch & Cary, 1996; Noll et al., 2006), but elemental (EC) and total carbon (TC) are often used as analytical surrogates (Birch & Noll, 2004; Noll et al, 2015). EC is the solid “soot” component of DPM, whereas TC also includes particulate organic carbon (OC) (Noll et al., 2007). EC and OC can be measured in filter samples using the standard NIOSH Method 5040 (NIOSH, 2003), and summed to obtain TC. In US mines, TC has been adopted as the analytical surrogate for DPM in regulatory activities. In metal/non-metal mines, personal exposures are limited under 30 CFR Part 57. In coal mines, limitations are made on emissions from each piece of equipment (30 CFR Part 72) rather than for personal exposures. This is because coal dust has the potential to interfere with TC measurements in personal samples. In some other countries, and for non-regulatory purposes in the US, EC is also commonly used as a surrogate for DPM in mine monitoring applications [e.g., see AIOSH, 2013). EC generally exhibits a linear correlation with TC (Birch & Cary, 1996; Noll et al., 2006 and 2007) but unlike TC measurements, which are analytically intensive, EC can be determined more simply using a laser absorption/extinction principle on filter samples (Noll et al., 2013)."

Jan 1, 2019

By K. Poorhaydari, B. M. Patchett, D. G. Ivey

In this paper, some applications of carbon extraction replicas, as samples for transmission electron microscopy (TEM), are discussed. Modern high strength microalloyed (HSMA) steels, used as structural or pipeline materials, have very small grains with substructures. Replicas used in TEM can resolve the grain boundaries and can be used for grain size measurements in cases where the small size of the grains pushes the resolution of conventional optical microscopes. The grain size variations obtained from replicas correlated very well with mechanical property variations, indicated by hardness, in the fine-grained heat-affected zone and base metal of some welded HSMA steels. Replicas are also very suitable samples for precipitate examination with analytical TEM. Advantages and limitations of the application of replicas, as well as some corrections for the estimation of the volume fraction of fine precipitates, are discussed.

Jan 1, 2005

By D. Neely

As Saskatchewan potash mines grow in age and size, mining reaches greater depths.  The stress-relief design principals which were empirically derived at shallower depths are beginning to show fault.  Nutrien Vanscoy Potash has began to encounter new ground support and panel design challenges which were previously had negligible effect.  While the initial reaction was to reduce extraction and implement distance buffers between operating machines, it eventually became clear that these would only provide short term relief and that in order to continue safely and efficiently mining broad areas, a fundamental change in the mine design would provide the long-term protection required.  Presented is a case study with an overview of the challenges encountered at Vanscoy Potash in areas of greater depth along with an account of the design changes considered, implemented and recommended for future success. 

May 4, 2025

By A. McLean, J. Hou

Waste slag is a major environmental concern within the metallurgical industry. In the steel industry, about 100 kg of slag is produced in making one tonne of liquid steel from iron in addition to that produced during ironmaking. The amount of slag from the steelmaking converter can be significantly reduced when charging hot metal with low phosphorus and sulphur contents. In this context, hot metal pretreatment is known as an effective means of preparing high quality charge material for the converter thus limiting the generation of residual slag during the steelmaking process. In the aluminum industry, about 2-4 tonnes of slag, including red mud from alumina production and dross from aluminum electrolysis and casting, are generated during the production of one tonne of aluminum. In recent years, reuse of waste slag from the aluminum industry is a topic that is receiving increasing attention. In this paper, the possibilities of using waste slag and by-products from the aluminum industry as a refining flux in the steel industry are discussed. Several successful processes to convert waste materials from the aluminum industry to steel refining fluxes are described. Some theoretical aspects of using calcium aluminate based flux for desulphurization are outlined together with results obtained from laboratory experiments on sulphur removal from hot metal. By intelligent use of waste materials, the disposal of solid waste from the metallurgical industries can be reduced.

Jan 1, 2004