Search Documents

By John C. Lyons

"The Wabana iron ore deposits occur as flat-dipping beds of oolitic hematite and chamosite, of Lower Ordovician age, which outcrop for 3 miles along the northwest coast of Bell Island, Conception Bay, Newfound-land, about 16 miles from St. John's.The deposits occur in three zones, Upper, Middle, and Lower beds, separated respectively by 30 feet and 215 feet of shale and sandstone. They are primary sediments laid down in a shallow tidal basin by the precipitating action of a marine environment on iron-rich fresh waters flowing into the basin.The ore-bearing zones, while of wide areal extent, are not uniform beds of hematite that can be mined wholesale. The action of waves and currents during sedimentation; the delta pattern, velocity, and transporting power of streams flowing into the basin; the contours and oscillations of the sea bottom on which the sediments were laid have all been fundamental in the emplacement of richer and thicker mineable sections, and of lean zones so intercalated with shale as to be unmineable.The preservation of the deposits is due to their location in the Conception Bay syncline and to a considerable upthrust of the country east of the bay in post-Ordovician time.The hematite deposits were first recognized as such in 1892, and soon after were acquired by the Nova Scotia Steel and Coal Co. They are now being mined by Dominion Wabana Iron Ore, Limfred, a wholly owned subsidiary of the Dominion Steel and Coal Corporation, Limited. Production started in 1895, and up to the end of 1955 totaled 58,588,516 long tons of hematite ore, having an average dry analysis of about 51 5 per cent iron, 11 8 per cent silica, 0·9 per cent phosphorus, and l ·5 per cent moisture. About 40 per cent of the total tonnage mined has come from surface stripping and on-shore mines. These areas have now been almost completely depleted, and operations are confined to submarine mines extending for two miles off shore under the waters of Conception Bay. Three sub-marine slopes are currently in operation, Nos. 3 and 4 working in the Lower Bed and No. 6 in the Middle Bed. A general picture of the workings is shown in isometric projection in Figure 1. Submarine mining has been entirely by the room-and-pillar method, with an extraction of 60 per cent. The deepest workings, at a vertical depth of 1,850 feet below sea-level, have a rock cover of about 1,500 feet. No mining is done in areas where the rock cover is less than 200 feet. To date mining has explored six square miles of a potential area that may exceed 50 square miles."

Jan 1, 1949

By T. Fekete, D. L. Flocks, R. T. Hart

The plugging effect of bacteria was investigated by injecting various concentrations of dead bacteria cells though sandstone cores. Pressure profiles along the cores were recorded periodically during the injection cycles. The plugging effect was analyzed using a plot of the ratio of reduced permeabilities to the initial permeability versus input volume. Results indicated that Tock permeability has little effect on plugging, but that the concentration of bacteria in the injection water has a significant effect on plugging characteristics. The pressure profile curves showed that bacteria penetrated several inches through the core but that the greater portion of the bacteria accumulated at the in-put end of the core.

Jan 1, 1960

By L. D. Smith

"The economic evaluation of a mineral project requires a great deal of diverse information to be brought together in one place. The greatest concern is that there will be an error by omission, so it is useful to have a detailed list of what one needs to know in order to make a thorough evaluation. The list that is presented below is intended to act as a checklist for the person who develops and reviews an evaluation, and as a shopping list for the persons gathering data at the project site.There are varying degrees of detail required at the different stages of evaluation in a project, from the ""quick and dirty"" overview, to the pre-feasibility study, to a full detailed feasibility study, to a due diligence review. This list addresses most of the economic variables in a project and can be used for all levels of studies. Its purpose is to identify a variable or issue and to raise a question, which the reviewer can then pursue in more detail using increasingly more comprehensive checklists for each topic. While developed from the point of view of a new project, this list is equally valid for an ongoing operation."

Jan 1, 1994

By G. F. Warning

"THE H. B. Mine is situated on the north side of Sheep Creek valley, about six miles southeast of Salmo, B.C. It is the most northerly producer along a belt containing a number of zinc-lead deposits, including the Jersey mine of Canadian Exploration Limited, 3 miles to the south, and the Reeves MacDonald mine, 12 miles to the southwest. The important zinc-lead producing area around Metaline Falls, Washington, lies 23 miles to the south. Two prospectors, Horton and Benson, located and staked the oxidized outcrops in 1.907. The property was named the H.B. after the two discoverers. Exploration by a number of operators failed to locate any sulphide orebodies until 1946, when Cominco began a geological study followed by surface drilling which was successful in locating extensive sulphide mineralization. A program of underground exploration revealed sufficient ore to war-rant mill construction. A 1 ,000-ton mill was completed by 1953, but due to low metal prices production was deferred until May, 1955. To September 1, 1959, 1,900,000 tons of zinc-lead ore have been milled; present milling rate is about 1,250 tons per day. Concentrates are trucked to the Trail Smelter, a distance of 35 miles."

Jan 1, 1960

By Törbjorn Naarttijärvi, Bengt Ludvig, Agne Rustan

"Falling rock is one of the major causes of serious injuries and deaths in Swedish mines. The research at the Division of Mining and Underground Construction was therefore directed toward controlled blasting in hard intense jointed rock.The project was started with an extensive literature review. Model tests with a new equivalent model material have been initiated to find ways of improving blasting techniques. The result showed that long cracks arise at the perimeter holes when there is a long time delay between adjacent holes. This led to the theoretical development of a new initiation method with ultra short delays (1,5 ms) f or controlled blasting, called ""Cutblasting"".Full-scale tests have been done at LKAB in Malmberget in hard intense jointed magnetite ore. Four different types of perimeter charges have been tested, namely: tube charges, ANFO mixed with plastic beads, detonating cord and linear shaped charges. Three types of initiation of the perimeter holes have been used, conventional (half-second delay detonators), instantaneous and ultra short ""cutblasting initiation"" (1,5 ms delay). The change in rock strength before and after blasting has been studied with bore hole periscope, vibration measurement and ocular observation of the rock surfaces.Thefull-scale tests showed that ""cutblasting"" with detonating cord in the perimeter holes gave the smallest damage to the surrounding rock. A combination of cutblasting initiation and tube charges are anticipated to give an even better result. A new method of controlled blasting using linear-shaped charges has also been tested, however, this charge type needs further development.The full- scale test also showed that the damage which can be seen on the rock surf ace is about the same for different controlled blasting methods but the not-visual-damage zone varies as much as from 0,1 to 0,7 m.A new classification system for controlled blasting regarding the damage to the surrounding rock has been devised."

Jan 1, 1985

By Lionel A. York

This paper outlines the type of water-bearing formations encountered in the Prairie Sediments and describes a method for effectively sealing these zones in order that shaft-sinking operations may be carried out with safety. Details are given of the procedure for carrying probe holes ahead of the shaft bottom. These probe or grout holes are employed for establishing a series of overlapping grout covers around the proposed shaft excavation to safeguard against large inflows of water during sinking. The pattern and length of grout covers cannot be standardized, and each cover needs to be specially designed to suit the varying ground conditions. In order to provide effective protection through the Prairie Sediments, the number of holes in any one cover would not be less than 8, and possibly as many as 64 would be required in certain zones. The length of covers would vary from 100 ft. to 250 ft. Emphasis is placed on the need for obtaining accurate geological and water information from exploratory holes, drilled in the shaft vicinity, in order to effectively plan all grout covers.

Jan 1, 1964

By K. C. Corin, Z. G. Song, J. Y. Liu, M. W. Zhang, State Key Laboratory of Mineral Processing-BGRIMM, J. G. Wiese

"In the present study effect of grinding media on flotation of two mineral systems have been investigated, viz. sulphide minerals (including a pure chalcopyrite and pyrite mineral, and two different base metal sulphide ores), and oxide minerals (quartz, hematite and cassiterite). It was shown that mild steel media milling produced lower recoveries in the case of chalcopyrite and pyrite, as compared to the case of milling using ceramic media. For oxide minerals, the effects of using mild steel media as opposed to ceramic media were not as significant as was for the sulphides, although, after mild steel milling, at acidic pHs their recoveries were significantly reduced. For two base metal sulphide ores, viz. Nkomati and Dexing ores, the differences resulting from different milling media , although marginal, were opposite for each of these ores.For oxide minerals XPS showed that oxides and hydroxides of iron (e.g. FeOOH) adsorbed on the surfaces of the minerals. In the case of the Nkomati ore, adding Fe2+ or F3+ ions after milling with chrome steel media resulted in reduced talc (gangue) recovery, but increased water recovery and reduced concentrate grades. Further investigations are currently in progress to examine the Fe ions effect on the talc surfaces and froth properties.INTRODUCTIONGrinding of ores is necessary to liberate the valuable minerals from its gangues to allow for their selective recovery during mineral processing such as flotation. The grinding process inevitably involves contact of the ores with the surface of the grinding device and the grinding media. Accompanied by grinding, several phenomena can occur including the grinding medium wear, formation of precipitated species on the ore surfaces, chemical reaction, galvanic effects, changes in the Eh of solution, etc. There is a considerable body of literature on the differences observed in the flotation of various ores after milling using various grinding media. Laboratory studies have used balls or rods made from mild steel, ceramic, stainless steel or chrome steel to investigate the effects of different grinding media on mineral flotation. It is found that the interactions between the ore and the grinding environment can affect flotation separation of sulphide (Wei and Sandenbergh, 2007; Bruckard, 2011), oxide (He et al., 2014) and carbonate minerals (Song, 2009 and 2010). For example, mild steel milling produces relatively high concentrations of Fe ions in the pulp, affecting the recoveries of minerals compared to the case of ceramic media. On the other hand, the stainless steel media or chrome media are reported to be beneficial to the recovery of sulphides, when compared to the cases of using mild or carbon steel media (Rey and Formanek, 1960; Peng et al., 2003a,b; Huang and Grano, 2006; Bruckard, 2011). It is not clear, however, whether these Fe ions may affect the surface properties of the minerals involved or the general pulp/froth behaviour and hence their floatability. In addition, in the study of an low-S PGE ore carried out by Miettunen et al. (2012), forged media grinding in the CO2 atmosphere led to the highest Pt and Pd grades and recoveries, but the high chrome grinding media gave lower flotation recoveries than those using the forged media."

Jan 1, 2016

By C. C. Walden, D. W. Duncan, P. C. Trussell

Thiobacillus ferrooxidans released copper from -400-mesh chalcopyrite at a rate of 54 mg/I/hr. Any flotation chemicals remaining on the concentrate did not inhibit the leach rate. Zinc rougher tailings were also leachable. With bacteria, 75 per cent of the zinc and 68 per cent of the copper came into solution. In the sterile controls, only 16 per cent of the zinc and 10 per cent of the copper were released; 100 per cent of the copper and 36 per cent of the zinc were leached from pyrite cinders through the action of bacteria, and 17 per cent of the copper and 10 per cent of the zinc were solubilized in the sterile controls. Less than 0.027 per cent of ~he iron came into solution. The majority of the copper in a converter slag was acid-soluble, but a reverberatory slag responded to microbiological leaching. About 62 per cent of the copper came into solution, compared to 12 per cent in the sterile control. The various factors influencing the rate and extent of microbiological leaching are discussed.

Jan 1, 1966

By E. C. Sanford

A laboratory-scale batch extraction unit and operating procedure for studying the hot-water separation of bitumen from Athabasca tar sands are described. The extractor evolved from earlier units and has been in use by Syncrude Research for the past 10 years. By using a unit such as this, it is possible to study tar sand feed quality and the effects of chemicals on the hot-water extraction process, while process variables are held constant. Data are presented to demonstrate the importance of surfactants to the process and the interrelated role of inorganic bases and surfactants.

Jan 1, 1979

By C. A. Y. Shephard, H. L. Brusset

Pressure maintenance by water flooding in the Pembina Field made consideration of wet crude dehydration and disposal of the produced water mandatory. Crude dehydration, the treatment and disposal of produced water, as well as the sale of gas and crude oil were expected to be handled more efficiently at one central point than at several conventional batteries. This plan was effected by routing the produced fluids to the central station by way of several well testing batteries referred to as satellites. To realize the full efficiency inherent in such consolidation the entire system was made self-regulating. Programming ensures the testing and proper routing of all products to their destination. Forty producing wells have been self-operated during the winter 1959 -1960 with gratifying results.

Jan 1, 1960

By Yin Guangzhi, Song Zhenlong, Li Minghui, Li Wenpu, Deng Bozhi

"Darcy's law is widely used to describe the oil and gas flow characteristics in the multi-pore media reservoir. However, the low-velocity non-Darcy flow of oil and gas occurs in the multi-pore media reservoir under low permeability conditions. Meanwhile, the high-velocity non-Darcy flow of oil and gas occurs in the multi-pore media near the wellbore. The gas flow velocities in coal in different deformation stage under different gas pressure gradient were tested and the relationships between gas flow velocity and gas pressure gradient were discussed, which can help us to investigate the transformation conditions of gas linear flow and gas nonlinear flow in coal. The results showed that the gas flow in the coal under low effective stress environment can be described by Darcy's law. The low-velocity non-Darcy flow of gas gradually occurred and the start-up pressure gradient increased in the coal as the effective stress increased. The low-velocity non-Darcy flow of gas also occurred in the coal at the yield deformation stage, however, the start-up pressure gradient decreased as the effective stress increased in this stage. In post-peak stage, the highvelocity non-Darcy flow of gas occurred in the coal under low effective stress environment. The gas flow in the coal gradually returned to be Darcy flow as the effective stress increased. The mechanism of the phenomenon is discussed based on the experimental results. The research results can be used to guide well test analysis and prediction of oil-gas production. INTRODUCTIONThe oil and gas flow in original multi-pore media reservoir are usually regarded as steady and linear processes and can be described by Darcy’s law. However, the low-velocity non-Darcy flow of oil and gas occurs in the multi-pore media reservoir under low permeability conditions. Meanwhile, the highvelocity non-Darcy flow of oil and gas occurs in the multi-pore media near the wellbore or workface. The gas flow in the multi-pore media even may be unsteady under some conditions such as gas emission and outburst.The phenomenon of underground water low-velocity flow in clays was deviated from Darcy’s law was found in the end of the nineteenth century (King, 1898). The deviation from Darcy’s law was later reported and investigated more (Swartzendruber, 1962; Miller and Low, 1963). These researches revealed that the start-up pressure gradient exists under low permeability conditions. Klinkenberg (1941) proposed that the permeability constant as determined with gases is dependent upon the property of the gas, and is a linear function of the reciprocal mean pressure. This effect can be explained by taking into account the phenomena of slip, which are related closely to the mean free paths of the gas molecules."

Jan 1, 2015

By M. Sakamoto

Copper foil is an indispensable material for Printed Circuit Boards (PCBs). PCBs in turn are essential elements of all electronic equipment today and thus important for our living in the new age of IT. The requirements from the copper foil market have lately been increasingly strict and diversified due to the rapid technical advancements in miniaturized high-density electronic equipment and highly integrated semiconductors. Tight control of thickness, metallurgical properties, surface morphology and characteristics is needed. In this paper, both electrodeposited copper foil for PCB and rolled copper foil for the flexible printed circuit board are discussed, and the recent technical developments in these copper foil products are reviewed.

Jan 1, 2007

By Meifeng Zhi, Yuqing Niu, Xixin Chang, Fengqi Zhao, Weimin Qiu, Hao Wang, Zhenqian Wen, Zujun Shu

An applicable Eluex process was developed for acid in-situ leaching (ISL) uranium mine in Bayanwula. In this process, uranium was adsorbed with strong base anion resin from the pregnant solution, then the loaded resin was eluted by sulfuric acid. After D2EHPA extraction, the concentrated eluate was enriched, and the loaded organic phase was stripped by sodium carbonate. The yellow cake was obtained by sodium hydroxide precipitation at last. The uranium concentration in the loaded strip solution was 52.8 g/L. Parameters of the process were determined, and the impact of the Eluex process in underground leaching was also investigated. In industrial design, 95% of raffinate went back to elution and 5% back to in-situ leaching. No significant effect on uranium leaching or resin adsorption was found.

Jan 1, 2020

By Eric R. Skonberg

"Technology exists today to blind drill a mine shaft 20 feet in diameter, unlined, over 3,000 feet deep. These shafts must be lined in the most economical, safe and expedient manner possible. A new technique of stacking precast concrete cylindrical sections in the unlined shaft has been developed to yield a dry and hydrostatically lined shaft .These sections must withstand an external radial pressure of 3,000 feet of water yet take up as little room as possible in the shaft . Using high-strength concrete, wall thicknesses may be kept at 2 feet. The outside diameter of the sections has been chosen to be 18 feet to allow for some annular space between the liner and shaft wall. The concrete sections are produced in segments 10 feet long weighing 75 tons each. During drilling operations, the concrete sections are cast and cured. After drilling operations are complete, a headframe is situated over the shaft. The unlined shaft remains full of fluid. A special liner running tool is mated with the section in three steel ports at the bottom of the section. The section and running tool are lowered into the hole, and the tool is disconnected and returned to the surface. Subsequent sections are lowered and stacked using the same operation. Grout is placed behind the liner to result in a dry shaft."

Jan 1, 1981

By J. C. Thornley, H. L. J. Drummond

"Fifty years of wear on the original carbon steel shaft of this hydro turbine necessitated repair operations in 1980. Both austenitic and martensitic stainless steels have been used individually as journal materials in separate trials on an80-inch long and 22-inch diameter radial bearing but neither one nor the other has been successful.The wear and cracking problems of the stainless steels leading to the present abandonment of both classes of stainless steel are described. In particular the dependence of the toughness of type 410 stainless steel on its tempering temperature and the susceptibility of that steel to quench cracking are highlighted because problems have been caused by both of these metallurgical factors.IntroductionAs part of a desire to improve the efficiency of a fifty-year old hydro-electric generating station on the Saint John River, the decision was made to change the journal and bearing material for the shaft bearings, which are stave-type bearings. For the initial fifty years of operation the bearings had been wooden (lignum vitae) and had run on the carbon steel shaft directly. For one of the four unit s at this station the performance of this combination has been truly excellent, and the remaining three sets of bearings had performed well. However there had been shaft wear on the units and the wear had made the shafts somewhat elliptical when a decision was made to install some sort of new journal on to three of the old shafts. [In addition to the wear on the carbon steel journals it was found that one shaft was significantly softer in the bearing area than it was immediately above the bearings (180 Vickers in comparison with 230 to 250 Vickers)] ."

Jan 1, 1985

By O. Engler, J. Friis, S. J. Andersen, C. D. Marioara, Y. Aruga

"This work investigates the early stages of precipitation in Al-Mg-Si alloys using a combination of high angle annular dark field scanning transmission electron microscopy (HAADF-STEM), selected area electron diffraction (SAED) and density functional theory (DFT) calculations. Quenching from a high temperature (solution) treatment leaves an alloy in a high-energy unstable state, with solute and vacancies in supersaturation. Thus, already at room temperature (RT) a large driving force exists for solute atoms to cluster and order on the Al matrix positions. DFT calculations indicate that strain alleviation is important at this stage. We observe larger regions of Mg-dominated L10 ordering together with a Si-dominated ordering of smaller clusters in a particular geometry connected to the Si-network found in all the precipitates. In addition, building blocks of the main hardening phase ?'', stabilized by vacancies, are observed at higher, typical pre-aging temperatures.INTRODUCTION Al-Mg-Si (6xxx) alloys are widely used in industry due to a combination of favorable properties such as strength, ductility, corrosion resistance and lightweight. They undergo a complex production route, usually consisting of the following thermo-mechanical steps: casting, homogenization, extrusion or rolling, solution heat treatment (SHT) and artificial aging (AA). The SHT takes place at temperatures above the solvus line in the phase diagram, usually between 500°C and 570°C, followed by a rapid cooling to RT. This ensures that high amounts of solute atoms, uniformly distributed on the cubic face-centered (FCC) Al lattice, together with a large amount of vacancies, are quenched-in. The material is therefore in a super-saturated and unstable state. During the subsequent AA, at temperatures usually between 150°C and 220°C, the solute atoms diffuse and cluster, forming metastable precipitates with needle/ lath/ rod morphologies having the main growth direction along <100>Al. With a maximum alloy solute level (Mg + Si) of only 2%, these precipitates increase material strength up to three times that of pure Al, and are essential for the final material properties. To understand and make better use of this phenomenon, it is imperative to research the nature of the precipitates (such as their atomic structure), measure their key parameters (number density, size, volume fraction) and connect it to material properties (Marioara, Andersen, Zandbergen & Holmestad, 2005; Marioara et al., 2014). The following precipitation sequence is given for the Al-Mg-Si system:"

Jan 1, 2018

By J. Budac, R. Kofluk, S. Mankasingh

Stainless steels such as 316L or 304 are normally relatively resistant to attack by nitric acid. However research at Sherritt International’s Fort Saskatchewan Operation reveals that when the stainless steel is immersed in an aqueous system in which nitric acid is used to dissolve metals such as cobalt or nickel, the steel can be seriously corroded. Sherritt is patenting a simple process for arresting the corrosion via the use of copper. This process is expected to substantially eliminate corrosion in processes where nitric acid is used to dissolve metals attached to a stainless steel substrate.

Jan 1, 2014

By R. A. L. Drew, C. A. Rodríguez González, Caleym W. F.

This work addresses the need of new refractories for copper converters. Technological improvements and environmental regulations for chromium containing refractories have generated this need. Chemical interactions, mechanism of penetration and the effect of oxygen potential and temperature in the system Cu2S-FeS-SiO2-O2 are presented for two refractories: a burned magnesite chrome brick (typically used by the copper industry) and a chrome-free spinel direct bonded brick. The main difference determined in the refractory performance was the blister copper penetration resistance; burned magnesite chrome brick is penetrated while direct bonded brick is not. These results are very promising since blister copper penetration has been reported as the major cause of refractory wear. The results are explained in terms of refractory porosity and wetting characteristics.

Jan 1, 2004

By E. Godfrey

The average man one meets on the street thinks of an explosive as a medium of death and destruction, something unstable which should be given a wide berth, because he knows little or nothing about its use or its stability. Briefly, explosives are compounds that develop very large quantities of heat and gas in an extremely short time and in a small space, thereby exerting enormous pressure upon surrounding bodies, and by the rapid expansion of this highly heated gas are able to perform a considerable amount of useful work. The amount of heat generated and the volume of gas produced by the decomposition of an explosive determines the amount of mechanical work it can do, and the time occupied by its change from solid or liquid condition to gaseous condition determines its shattering effect. Explosives manufactured by reputable people are not extremely dangerous, on the other hand they are quite safe if handled in a proper manner. Furthermore, before an explosive can be placed on the Canadian market a sample must be submitted to the Explosives Division of the Mines Department, who may condemn or permit its manufacture, according to their findings regarding its safety in handling and its stability during storage.

Jan 1, 1926

By S. Glen

Cyanide management practices on modern gold plants are becoming more onerous, due to environmental pressures, particularly for signatories to the International Cyanide Management Code. Operations are therefore seeking to reduce levels of weak-acid dissociable (WAD) cyanide reporting to spigot discharge as well as to any eventual discharges from the tailings storage facility (TSF). Current gold industry standard processes primarily include the oxidation of cyanide by means of sodium meta-bisulfite (SMBS, or SO2) with air, Caro&apos;s acid (H2SO5) or hydrogen peroxide (H2O2). These processes require the transport and usage of expensive oxidizing reagents, along with the safety and environmental issues associated with these corrosive and toxic chemicals. Maelgwyn Mineral Services (MMS) has developed the MMS CN-DTM process, which utilizes the Aachen ReactorTM, a high-energy mass-transfer superoxygenation system, in conjunction with an activated carbon-based catalyst and no additional reagents, to increase the rate of cyanide oxidation to cyanate, the thermodynamically more stable form. Testwork conducted at the Maelgwyn Australia testwork facility in Perth Australia is described, at both pilot scale and continuous bench-scale, on a sample of tailings effluent obtained from an Australian gold plant. WAD cyanide is demonstrated to be lowered using the MMS CN-DTM process from an influent of 130 mg/L to the required levels for discharge to TSF (<50 mg/L). The continuous test results showed stable operation over three residence time turnovers. The pilot-scale results demonstrated the efficiency of the process at the reasonably large scales required for engineering cost estimation.

Jan 1, 2011