Search Documents

By W. A. Jones

THE estimation of the average value of gold ore involves many considerations, among them the correct sampling of the deposit, the dilution by waste, and the loss of high-grade fines. It is a common experience that, after all these factors have been evaluated, adjustment of the assays is necessary before satisfactory agreement between the calculated mine grade and the mill heads is obtained. In fact, at many mines the latter correction overshadows all others in the preparation of routine estimates. For this reason it is proposed to deal only with the mathematical treatment of mine assays and the problem of bringing estimates into conformity with the corrected mill heads. Mine assays differ from physical measurements because the range of values is very great and these are not symmetrically distributed above and below the average, there being fewer high than low results. There is no widely accepted mathematical procedure for determining the average of series of measurements which exhibit these characteristics. Customary practice consists in empirically reducing high assays until a satisfactory agreement with mill heads is reached. It was thought that more confidence could be placed in grade estimates if a logical basis for calculations could be devised .. In an attempt to find a fundamentally sound procedure, amenable to practical application, many series of assays comprising over 235,000 channel samples (1) were studied at Hollinger Consolidated Gold Mines, Limited. Such an investigation could only be made where records covering many years of operation are available and where tabulating and calculating machines are in use. The results are recorded in the hope that the relationships noted for the large groups of assays used are of fundamental character and that the data will be useful to others dealing with the problem of grade estimation.

Jan 1, 1943

By J. P. Caulfield

THE Hudson Bay Mining and Smelting Company's underground mine at Flin Flon, Manitoba, has in the past been serviced by two working shafts-the North Main shaft, and the No. 3 shaft. The North Main shaft is used to hoist the total production from under-ground, and handles the greater part of the mine supplies and crews. The shaft is five-compartment design, rectangular in cross-section, and is equipped entirely with steel shaft sets from the surface to the finished depth of 2,210 feet. Hoisting equipment in the surface plant will not permit the North Main shaft to be extended below its present finished depth. The No. 3 shaft, located approximately 2,300 feet from the North Main shaft, is used primarily as a ventilation shaft, and for hoisting lower-level development waste to the 390 level, where this material is used as mine fill. The No. 3 shaft is of standard rectangular design, timbered with 8-in. by 8-in. creosoted fir sets, hung on 6-foot centres. From the surface to the 1,430 level, the No. 3 shaft consists of three 5 ft. by 5 ft. compartments, and below this level to the completed depth of 2,300 feet, the shaft is increased to four compartments. To service the mine and to expedite development below the 2,210 level, a one and one-half compartment winze was sunk from the 2,210 level to a depth of 766 feet, or approxima tel y the 3,000 level.

Jan 1, 1941

By Tyson Birketi, Françoi Robert, Steve Green, Dan Richardson

Detailed sampling using a portable diamond drill, and inter laboratory comparison of selected samples have been combined with statistical studies of truncated populations to establish the gold content of several outcrops in the Val d'Or area. The outcrops chosen are non-mineralized. The background gold concentration in the rocks of the region is 5 ppb or less. Gold is distributed relatively homogeneously within the outcrops studied except for slightly increased concentrations within quartz-tourmaline veinlets. Three samples, of which 20 grams of powder are analyzed for each, can adequately determine the gold concentration of a structurally simple outcrop in the Val d'Or area.

Jan 1, 1992

By A. D. Dalvi

Economics, Resources, Environment and Technology are the major driving forces in the base metals industry. However, these factors are intertwined and together will propel the industry in the future. The demand for metals has grown with economic expansion, between 2 to 4 % p.a. The current growth cycle has been driven by economic expansion in China where the demand for base metals has risen from - 7 % of the world demand in the 90's to - 25 % of world demand today, and rising. Base metals are commodities and their demand and price are cyclical. Historically metal prices have declined in constant dollars, forcing the industry to reduce costs, increase productivity and increase the scale of operation for economies of scale. Due to resource depletion and capacity expansion the industry is driven to expand its reserve and resource base. However, in the case of sulphide deposits of copper and nickel it appears to be a losing battle. For nickel the laterites represent a vast source at this time. Their development requires development of new technologies to make these resources economic. Emission reduction is being increasingly mandated in most jurisdictions with all governments enacting progressively more stringent regulations. The industry has been responding with technological innovation. With the Kyoto protocol there is a push to reduce energy intensity in metal production. Technological innovation is driven by all the other factors and is leading to novel ways of doing exploration, mining and processing, that would maximize resource delineation and utilization, reduce costs, increase productivity, reduce energy consumption, maximize asset utilization and reduce environmental affects. Development of alternative technologies such as Pressure Acid Leach of laterite for nickel, bio-leaching, heap leaching, SX-EW etc are being adopted to achieve the aims of the industry.

Jan 1, 2005

By W. Graham

"IntroductionEFFLORESCENCE is herein considered to be any deposit of salts on the surface of a masonry structure that is brought from within or through the structure by capillarity and deposited by evaporation. Usually, efflorescence is white although green, yellow, and brown efflorescence is sometimes observed.The common white efflorescence almost always consists of sulphates of the alkali and alkaline earth metals and calcium carbonate, although sodium chloride is frequently present in structures erected near the sea shore.The first and most obvious result of the presence of soluble salts in masonry is the unsightly accumulation of these salts on the surface. This is particularly noticeable early in its life and is frequently fugitive ( 1), as much of the salt is soluble and is gradually washed away by rain. This removal can usually be facilitated by scrubbing; the structure with dilute hydrochloric acid.A more serious effect is the continuous accumulation of soluble salts as a result of ingress of sulphur acids in rain water or water from the ground. This may eventually cause spalling and disintegration by crystallization of salts in the pores of brick and mortar. An example of this type of failure, resulting from the crystallization of calcium sulphate, is discussed by Hardesty (2). Butterworth (3) describes similar failure resulting from •crystallization of magnesium sulphate."

Jan 1, 1954

By G. Lodewijks

This paper explores the savings that can be achieved in the energy consumption of belt conveyors used in mines by changing the conveyor components, the operational parameters of the system or the belt properties. First the concept of energy savings is introduced by looking at the energy consumption of belt conveyors from a theoretical point of view. Also methods for the calculation of the power consumption of a belt conveyor and the associated emissions are presented. Two case studies are presented in which the effects of the change of the operational parameters of the system, in this case the belt speed, and the belt properties, in this case the application of aramid products in the belt, are presented.

Aug 1, 2013

By John Blackshaw

NEW sources of supply of tungsten concentrates became necessary when the flow from the Far East was blocked in 1942. In Canada, one source has been noted in the workings of the Hollinger mine at Timmins, Ontario. For many years, a small amount of scheelite had been removed with the gold ore, and an appreciable tonnage of scheelite still remained in the mine. At the request of the Dominion Government, a plant was built to recover this scheelite in the form of a concentrate that could be used by the alloy-steel industry without further preparation. The plant began operating early in March, 1942, and a small tonnage of ore, carrying scheelite and gold values, has been treated daily since then. The possibility of recovering the scheelite had been considered on several previous occasions. Each time the proposal had been given up because the total profits from the enterprise were estimated to be insufficient to repay the capital cost of building the recovery plant. At the time the plant was built, additional information had been gathered about the tonnage and grade of the scheelite ore in the mine, and several thousand tons of ore grading higher than 0. 25 per cent WO3 (tungstic trioxide) were known to be available.

Jan 1, 1943

By F. J. West

This paper deals with Jones & Laughlin Steel Corporation's new Adams mine, near Kirkland Lake, Ontario. After a brief discussion of ore structure, type, reserve tonnages, etc., the main body of the paper discusses the establishment of an open-pit limit based on economic considerations. The method used by J & L to arrive at an economically sound open-pit boundary its outlined fully. Physical limitations to open-pit boundaries are mentioned briefly. The paper concludes with a few remarks on the mining equipment in use and on its productivity

Jan 1, 1966

By Leonard Kellogg

Introduction The Mine Manager or Superintendent is a man faced with a difficult problem. He must direct the activities of his mine in such a manner that, over a period of time, the greatest possible profit will be realized. In this respect, a mine is no different from any other business organized for profit. What makes the mine manager's task so difficult then? The profit of a mine is determined by -among other things -the grade of ore, the market price of the metal or metals produced, and the cost to operate the mine. The mine manager cannot do much about the first two of these, but he has considerable control over the operating cost. This cost will depend in large measure on the nature of the programme on which he plans to operate his mine. This operating plan may be broad or specific, on a long-range basis or on a month to month basis. The development of the plan, however, is made very difficult by the existence of so many factors which must be considered. These may be (1) factors requiring decisions based on the best judgment and interpretation of engineering and geological information available, or (2) items which must be considered but which are largely non-controllable. To be more specific, examples of such items would be: (1).-(a) The amount and type of development work to be done in relation to amount of ore to be mined. (b) Mining methods to be followed and type of equipment to be used. © Amount of exploration diamond drilling to be done if the orebody is not clearly defined. (2).-(a) Rock type and degree of hardness. (b) Width, depth, and pitch of veins. © Amount of work requiring timbering. (d) Faults encountered. (e) Water and gas conditions met with.

Jan 1, 1952

By H. G. Stephenson, C. W. Gregory

"This article describes the methods used for pillar extraction in the Wilson Seam at Canmore Mines, Alberta. The Wilson Seam is extremely gassy and varies in thickness between 7 and 30 ft, with an average of 12 ft. The gradient varies from 5 to 30 degrees, with an average of 15 degrees. The seam was developed using Lee Norse miners to form pillars which the company intended to extract using the same machines. Before pillar extraction commenced, an abandoned and inaccessible mine 160 ft above the Wilson had to be drained of 360 million gallons of water. When this was done pillar extraction commenced. Conditions in the mine slowly deteriorated and after 6 months the decision to withdraw the continuous miners was taken. Slusher hoists were installed to replace the continuous miners, with the result that roof conditions and safety steadily improved."

Jan 1, 1972

By E. Ghali

For engineering applications, magnesium is usually alloyed with one or more elements which include aluminium, manganese, rare earth metals, lithium, zinc, and zirconium. Under normal environmental conditions, the corrosion resistance of magnesium alloys is comparable or better than that of mild steel. The oxide film thickness on pure magnesium after exposure for only ?10 seconds at ambient temperature is 2.2 ± 0.3 nm. Exposure to humid air or to water leads to the formation of a thick hydrated amorphous film that has an oxidation rate less than 0.01 pm/ y. E-pH diagram and high temperature corrosion are discussed. The pH values between 8.5 and 11.5 correspond to a relatively protective oxide or hydroxide film that is more stable at higher pH. Structural applications of magnesium alloys are limited by creep strength rather than by oxidation. Active and active-passive behaviours of magnesium alloys are discussed. The pilling Bedworth Ratio values of oxide and hydroxide are 0.79 and 1.77 respectively and so the formation of Mg(OH)2 inside the oxide film could lead to the development of cracks. Microbiologically influenced corrosion and rational biodegradation of magnesium alloys are discussed because of their interest for medical care.

Jan 1, 2006

By P. -A. Bosse, J. Robitaille, P. Blatter

The LaRonde ore is a Cu-Zn-Pb ore with gold (3-4 g/t) and silver (60-100 g/t). The precious metals are recovered with copper concentrate, zinc concentrate and cyanidation of zinc tails via Merrill Crowe precipitation. Subsequent to a recent mill expansion, excessive gold was reporting to zinc concentrate with a concurrent decrease in gold to copper concentrate. Owing to the higher return obtained from the metal, the mill endeavors to recover additional gold and silver to the copper concentrate and minimize the placement of precious metals to the zinc concentrate. A gold deportment study showed that the gold occurs mainly as küstelite, with a moderate amount of electrum and a minor amount of native gold. It also showed that various sulfur-based Au-and/or Ag-bearing coatings on liberated küstelite and electrum were the major mineralogical factors that caused gold and silver to report to zinc concentrate. By frequency, such coatings were observed on 70-80% of total liberated gold particles reporting to the zinc concentrate. Based on the gold deportment and the chemistry of the coatings, the collector chemistry was reviewed and a new collector was added into the circuit which resulted in a significant increase in gold and silver recovery to the copper concentrate. The information obtained from the mineralogy confirmed and guided other process optimization. In this paper, the authors will describe the process mineralogy of the LaRonde ores, and in particular, the mineralogical evidence diagnosing the problem. Reference will also be made to the rationale behind how the problem was solved, the results achieved, and future steps in optimization.

Jan 1, 2005

By A. E. McIlhinney, I. E. Puddington, C. E. Capes, A. F. Sirianni

"Two main problems are associated with the removal of pyritic sulphur from coals. The first is due to the fine state of dissemination of pyrite, which requires grindin1 to a very fine size to accomplish liberation. The second problem is caused by the similar surface chemical characteristics of coal and pyrite, which complicates separatio11 methods based on this property. In the work described here, the problem of fine particle size was overcome by using the selective oil agglomeratioa method developed at the National Research Council of Canada. Recovery of more than 90% of the combustible values was possible, even with particles only a few microns in diameter. Experiments using conventional chemical depressants for pyrite met with little success. It was found, however, that pyrite may be rejected during coal agglomeration through treatment with the iron.oxidizing bacteria, thiobacillus-ferrooxidans. The conditions for maximum pyrite separation are described and possible mechanisms by which the bacteria act are discussed."

Jan 1, 1973

"The Hardy Cross algorithm offers a reliable method of solving network systems of fluid flow and has become widely used for solving water and ventilation flow networks. A limitation is that computational iterations and time to solve a network rises rapidly with the size of the model and modern detailed ventilation networks have typically grown to thousands of airways. Non-linear matrix solving methods can offer improved performance, however these are more complex and may be unstable if initial estimates are poor. This paper presents improvements that can be applied to the traditional Hardy Cross algorithm to greatly reduce iterations and solving time for large ventilation models. INTRODUCTION The Hardy Cross algorithm (Cross, 1936), was originally developed to solve water flow in city and urban pipe networks. Using principles of Kirchhoff’s electricity current laws, Hardy Cross developed an iterative algorithm for solving non-linear equations associated with network water flow. Traditional network analysis research refers to the various members of system networks as branches, nodes and meshes. This terminology has been changed in this paper to airways, junctions and loops respectively which are terms more familiar to engineers in mine ventilation. When Kirchhoff’s laws are applied to fluid networks, the following assumptions can be made: •The sum of fluid flows into a junction must equal the sum of fluid flows out of the junction.•The sum of pressure losses around any loop through a network system must be equal to zero.An iterative solution can therefore be achieved by initially guessing flow in a network, calculatingthe pressure losses around the network loops (Figure 1), and applying flow corrections using Newton’s method for each loop if the sum of the pressure losses does not equal zero. To solve the system, a loop must be defined for every segment or series of segments between a junction of 3 or more airways.The Hardy Cross algorithm has been used extensively for ventilation network analysis since the introduction of the first electronic computers (Tien, 1997), however numerous other variations and methods have since been developed through the use of matrices to solve the required system of nonlinear equations. Commonly used algorithms such as the Newton Raphson method (Brown, 1969), the Gradient method (Todini & Pilati, 1988), the Linear Theory method (Gupta & Prasad, 2000), and Coupled Network Solver (G. Danko, 2008) have found general use in fluid flow network solvers (Rossman, 2000). Despite poor and sometimes unpredictable convergence performance however, the Hardy Cross algorithm still has unique properties that make it attractive for ventilation models. Some benefits are:"

Jan 1, 2019

By Floyd Smith

Based on underground observations made in .the coal mines of the Dominion Coal Company Ltd., this paper deals with the stress phenomena in the approach roads and headways and in the gob areas associated with the longwall method of total extraction. The deformation of roadways during development and the deformation of roadways during the total extraction period is delineated and presented in graphical form .. Conclusions are made as to the feasibility of the introduction of the retreat method of longwall extraction in one of the colhenes. The importance of future studies are enumerated, especially. those pertaining to the determination .of the opti.m.um sizes of protective pillars and to increasing the efficiency of the current methods of artificial roadway support.

Jan 1, 1967

By V. K. Karra

A mathematical model for the performance of a vibrating screen is developed in terms of an oversize partition curve. This is a normalized curve for any assemblage of particles presented for screening when their size is normalized with respect to the 50 per cent passing size (d50 ) under the prevailing screening conditions. Based on the throughfall aperture (hT) of the wire mesh on the deck, the effects of oversize (% >hT), half-size under (% <0.5 hT), deck location and feed rate were evaluated using the existing screen sizing information. All these variables and also the near-mesh (1.25 hTx 0.75 hT) content (%) of the feed affect the d50. Performance data from different decks of a double-deck screen with various feed rates, size distributions and screen apertures were used to evaluate the near-mesh factor. Effects of wet screening and material bulk density are also incorporated in the model. This generalized model is useful for the simulation of a multiple-deck screen. It furnishes the sieve analysis information of all the deck output streams and therefore has a potential use in the over-all circuit evaluation when used in conjunction with relevant crushing and grinding performance models. An example illustrating the prediction capabilities of the model is given.

Jan 1, 1979

By Michael R. Brown

A facilities success or failure of doing well during a regulatory inspection is typically measured by the number and type of citations that result, and financial liability resulting from those citations. The success of a facility during an inspection depends on several factors including, the preparation prior to an inspection, behavior and activities during and inspection, and finally, action taken following the inspection. This paper contains suggestions for improving inspection results and establishing an attitude of compliance at manufacturing and mining facilities.

May 1, 2002

By J. Reinhardt, R. Uken, S. S. Chinnasamy

Au mineralization in the Kilpwal Gold Mine is confined to laminated quartz-carbonate lodes and associated alteration along the Klipwal Shear Zone (KSZ) in the upper Mozaan Group of the Mesoarchaean Pongola Supergroup. The brittle-ductile shear zone is characterized by inner and proximal hydrothermal alteration domains that are comprised of chlorite, epidote, sericite, pyrite, arsenopyrite and gold. Possible sources of gold are: (i) paleo-placer U-Au rich conglomerates from the lower Mozaan Group; (ii) the underlying mafic volcanics of the Nsuze Group; (iii) greenstone belts in the basement to the Pongola basin. Post-Pongola granites probably provided the heat to mobilize auriferous fluids into the KSZ.

Jan 1, 2011

By J. M. Réjean Gagnon

"Quebec Cartier Mining Company is currently mining a low-grade iron ore deposit in northeastern Quebec. The Company is producing some 8,000,000 dry gross tons of concentrates per year, grading about 66 per cent iron. The pit, which is located on the keel or hinge line of a fold, will eventually be about 1,000 feet deep with a surface area of 8,000 by 2,600 feet. The most significant structural discontinuities in the mine are the natural bedding planes and secondary perpendicular joints. The exposed walls are subjected to a sub-Arctic climate and heavy blasting occurs approximately six times a month.QCM utilizes design and operating techniques to control rock fall. Steps are also being taken to analyze the ultimate over-all pit slope stability."

Jan 1, 1968

By J. Kempken, R. Hagmann, C. -P. Reip, W. Hennig

The CSP technology symbolizes a highly productive process for the cost-effective production of steel grades with a range of sophisticated properties comprising both the inner quality of hot strip, its surface formation as well as the relating technological characteristics. Thanks to extensive development work undertaken during the last 15 years, the range of steel grades that can be produced was continuously expanded and the process technology optimized. The present paper describes the ongoing development work concerning the production of higher-strength, microalloyed pipe steels. The resulting hot strip, due to the associated thickness and the potential pipe diameters, is particularly suited for being processed to HFI-welded pipes. Based both on ferrite-pearlite as well as very fine-grained, ferrite-bainite hot-strip microstructures, strength levels of up to grade API X80 can be realized. It can be demonstrated that hot strip produced in a CSP plant has very good toughness values at temperatures down to -60°C and can even make application with required sour-gas resistance possible.

Jan 1, 2005