Search Documents

By Jaques A. L, Heinrich C. A

Mt Todd lies towards the south end of the Pine Creek Geosyncline, sandwiched between the Cullen Batholith and the Edith Falls Basin, in an area of regionally metamorphosed sandstones, siltstones and shales. The Batman deposit, some 3 km west of Mt Todd is a sheeted quartz vein system hosted within greywackes of the Palaeoproterozoic Burrell Creek Formation (Finniss River Group). The gold-bearing quartz veins, trending 010¦-020¦ and dipping 60¦-70¦E, are commonly 0.5 to 5 cm wide and occur at intervals which are from 10 cm to 1 m apart. Gold tends to be restricted to the quartz veinlets and immediately adjacent country rock. Grade Control utilises two 4 m 'collar' samples which are collected from each 8 m production blasthole. The irregular distribution of the quartz veins and erratic gold mineralisation has resulted in a disseminated 'salt and pepper' type of gold occurrence, with only a poorly defined footwall. Delineation of ore and waste blocks for mining uses an approach which combines the smoothing effect of kriging with a pragmatic view of the raw data. Large ore blocks with simple geometry help to minimise mining dilution, reduce block variance and give good reconciliations to interpreted ore tonnes and grade. Daily mine face advance is reported against truck counts and provides continual comparison with budgeted production. All data processing uses Gemcom software, together with Lotus spreadsheets.

Jan 1, 1994

Whether you are an employee, contractor or consultant working in the mineral industry, there are pressures to deliver the best possible performance. Technical professionals are usually driven by an internal desire to perform to a high standard because of personal pride in their profession, but there are an increasing number of external requirements to demonstrate that the actions taken were based upon reasonable grounds and that the work conformed to current best practice. People expect these best practice procedures to be followed and governments are now requiring those tendering for contracts to be registered in some way and to be participants in quality assurance schemes. One is not immune to these pressures just because you are working in a less legislatively sophisticated developing country in the circum-Pacific rim (Pacrim) region.

Jan 1, 1995

By M A. Gontalves, A F. D C Varajpo

The Rio Capim kaolin district, located in the north-east of Parß State, Brazil, constitutes one of the worldÆs largest high-whiteness kaolin reserves for the paper coating industry. It contains, at the base of the main ore, a soft kaolin that gradually changes at the top into a ferruginous duricrust followed by a flint kaolin. The flint kaolin is completely discarded during the exploitation of the soft kaolin. With the view of a more complete beneficiation, aiming at a sustainable development of the minerals industry, the use of this residual flint kaolin has been considered for the manufacturing of zeolites. Zeolites were synthesised from the flint kaolin through a reaction between metakaolinite with soda at 80¦C, for durations of 24 to 144 hours. The transformation into metakaolinite was carried out at 800¦C and was not affected by the titanium oxides. For a synthesis time of only 24 hours, a zeolite 4A very close to its theoretical definition was obtained, whereas for synthesis times longer than 96 hours, a slight formation of hydro-sodalite was also observed. The synthesised zeolites were tested as cationic adsorbents on 0.5 molar solutions of Cu, Pb, Cd and Zn. The adsorption was measured for contact durations of one and three days. It was noted that the exchange kinetics were slow and that the retention was significantly greater after three days than after one day. The retention was greater than 50 per cent of the theoretical exchange capacity for Pb, Cd and Zn, which was different to Cu, where the retention exceeded its theoretical exchange capacity.

Jan 1, 2008

By A J. MacDonald, M P. Raffield

The South Deep massive orebody consists of 20 to 30 m of payable conglomerates ranging in dip from 11¦ to 20¦ and at depths of between 2400 m and 3400 m. The mine design process selected a mining method with a proven record of application that could be adapted to overcome the inherent difficulties associated with the depth, thickness and structural influences of the South Deep orebody. A modified cut and fill mining method provides a concentrated and highly flexible method of extraction. An integrated destressing cut will enable the modification of the stress environment such that it is suitable for massive mining operations. The choice of backfill type and stoping width in the destressing cut ultimately determines the characteristics of the stress modification and, as such, is critical to the success of the cut and fill operation. This paper discusses the decision process undertaken to determine the optimum backfill type and stoping width combination in terms of, conditions in the destressing cut faces and in the massive mining environment. Numerical modelling has been extensively used to analyse various scenarios to aid in the decision process.

Jan 1, 1998

By B Bradák, D Asahina, S Saydam, S Akdag

Human exploration of Mars has been on the horizon of scientific goals for decades now, and as part of the objectives of human missions to various planets, one of the possible goals is opening new economic frontiers by the potential extraction and utilisation of resources, eg mining minerals and using surface regolith (Neukart, 2024). A comprehensive understanding of surface morphology, lithostratigraphy, basic structural geology, and civil engineering technology is essential to conduct mining operations for resource extraction on extraterrestrial planets. For instance, proper assessment of the risks associated with excavation and infrastructure construction under unique environments such as low gravity, surface irregularities, and the presence of regolith is fundamental. Such knowledge has been accumulated through satellite imagery and numerical topographic data using remote sensing technology, as well as seismic surveys by the on-site lander (Knapmeyer- Edrun et al, 2021; Banerdt et al, 2020; Giardini et al, 2020). Recent studies show that Marsquakes could be caused by the release of strain energy generated by the contraction of Mars. In particular, Marsquakes occur around the graben where many faults exist and form regularly spaced patterns. This implies that Marsquakes occur when the stress field of the Martian crust is an extension condition, and normal faults appear on the surface. In this study, we focus on so-called graben structures, one of Mars’s common tectonic structures (Plescia, 1991; Banerdt et al, 1992; Hoogenboom Hagen, 2014). The study aims to provide additional information about the tectonic environment during the formation of such features and, in addition, the internal mechanical-rheological structure of Mars, revealed by the geometrical pattern of faults modelled and simulated in a laboratory environment.

Sep 1, 2024

By J P. Moodie

Recent trends in flotation technology are briefly reviewed. These show that considerable development has been made as the operators, suppliers and technologists have responded to the challenges of the industry. Most of these advances have been based on empirical and phenomenological methods. There is a considerable opportunity to make further advances through a more fundamental, scientific approach. Some of this work is discussed and, although progress is being made on this front, industrial uptake has been somewhat slow. A number of specific issues facing the industry are discussed.

Jan 1, 2005

By Woods PW

Consulting Engineers have been used in the mining and metallurgical industries for many years. The traditional role of the consultant overseas has been one of assisting with conceptual design right through to con- struction and commissioning as well as on occasion acting solely in specialist fields. This role developed because mining companies wished to concentrate on building up the permanent organisation they require to operate their mines and treatment plants without the traumas of increasing staff for the design and construction period and reducing it on completion. In Australia where there have been few individual minerals projects of magnitude (until recently) companies have looked after their own detailed engineering and construct- ion management employing consultants mainly in specialised fields.

Jan 1, 1975

By Hoffmann CF, White NC, Tedder IJ, Wood DG

Since the discovery of Pajingo in 1984, the northern Drummond Basin has emerged as a significant new gold province, and has become the focus of intense exploration for epithermal gold mineralisation. Prospects in the Conway area are hosted by felsic to intermediate lavas and volcaniclastic rocks near the base of the Drummond Basin sequence. These Drummond Basin rocks appear to represent favourable hosts to mineralisation because they are cut by structures which could have focussed and channelled fluids on a regional scale, and because they constitute a possible source of gold and, perhaps more significantly, sulphur for the transport of gold. Prospects in the Conway area are up to 15 km2 in area, and are of the adularia-sericite type. They illustrate many of the classic features (siliceous sinters, alteration mineralogy, and fluid characteristics) recognised in epithermal deposits. K-Ar dating of sericite alteration in three of the prospects has produced a range of ages from 283 to 334 Ma, suggesting that the systems are the product of multiple hydrothermal events.

Jan 1, 1990

By R C. Schodde

The future of any mining company depends on maintaining and growing its access to high-quality mineral resources. Often the true size of a given resource is not fully recognised until after mining has commenced. Also, the strong desire to increase production puts pressure to expand the resource base of the mine to get maximum value out of the capital employed. This, plus diminishing M&A opportunities and declining world-class greenfield discovery rates, makes brownfields exploration a high priority activity in any operating company. For the success and long-term survival of the company it is critical that this is done well. The primary aim of brownfields exploration is to find or acquire new deposits within economic transport distance of an existing mine that will add materially to shareholder value through: mine or capacity expansion, displacement of lower-margin ore from the mine plan, preserving and extending the mine life, and ensuring potential value is understood in order to maximise potential future mine development or exit. A number of strategic principles are important in any program designed to achieve these aims: understanding the life of mine (LOM) production profile and the related key drivers for exploration, understanding the dynamic nature of the brownfields search space, understanding and measuring depletion of the brownfields search space, understanding the potential of the near-mine region, investing in exploration technology to expand the search space, and investing in a basic geological understanding of the ore-environment. Examination of the LOM profile will highlight critical issues facing development plans for the mine including future grade and throughput issues, key technology requirements or innovations and scenarios for increased production. Exploration targets in the brownfields program should address these key issues. Often it is as æsimpleÆ as keeping mine development sufficiently far ahead of extraction to allow time for the various phases of exploration and resource assessment drilling. Because of the low additional capital costs required, expansion of the brownfields search space is strongly leveraged to: metal prices, development of new markets, incremental operating cost reductions, strategic changes in downstream requirements in integrated businesses, depletion of higher unit-value ores, and new technologies (both extraction and exploration). Therefore the brownfields search space is likely to incrementally expand through time and must be regularly reviewed. This is also important as any given search space will be progressively exhausted, resulting in smaller and higher cost discoveries. It is therefore important to monitor and critically review sustained trends of increasing brownfields discovery cost. The first wave of discoveries in any camp are usually empirically driven and do not need a strong geological understanding. However, an improved geological understanding is critical to making the next generation of hidden discoveries. To illustrate these points, a case study was carried out on the exploration and development history of the Kambalda nickel camp. Over a period of 40 years, more than 40 deposits were found containing over 1.7 million tonnes of nickel metal. Efficient mines need to maintain reserves for operating flexibility. Consequently, the company needs to clearly understand the global resource in order to maximise its full potential. In addition, understanding the full brownfields potential earlier in the development of a deposit rather than later, creates optionality through the flexibility that this understanding brings to future development choices. To ensure best practice in attaining this aim, the roles and responsibilities of the exploration team and the mine operation should be clearly understood. It is important for the explorers and the operators to have shared views about what needs to be done. Typically, mine operators would be accountable for identifying future resource requirements to support the life-of-mine production schedule whilst explorers would be accountable to ensure best-practice assessment of brownfields exploration opportunities. This would include an assessment of the global undiscovered endowment in the regional near-mine area. The balance between brownfield exploration drilling and resources to reserve conversion will need to be decided to ensure efficient operations are maintained. Both need to agree the optimum level of brownfields funding taking into account: urgency to replace or grow reserves, and quality of opportunities (relative to those elsewhere). The ultimate cost of ignoring the full brownfields potential of an operating asset can be significant, ranging from inefficient and poorly planned operations, lost opportunity cost and resultant value through under-utilised resources and, in the worst case, early exit from the asset at the bottom of the commodity cycle û leaving behind huge amounts of shareholder value.

Jan 1, 2006

Mine geologists have access to an economic mineral deposit, production parameters and secure exploitation title. They are well placed to understand ore formation and should contribute to the effective exploration of company mine property. Application of their special skills has been curbed by pre-occupation with production duties and by company re-engineering, including staff reductions. Contributions to exploration have been diminished and personal development inhibited. Modified management is required. Participation in mineral system studies and in exploration research comprise part of the basis for the re-emergence of mine geologists on the exploration scene. Changes in investment strategies in the minerals industry may create new employment opportunities. With regard to estimation of resources and reserves, the competence of practitioners who are incapable of disclosing their methods in transparent terms is under question. Ethical standards are also under public scrutiny because of some notable malpractice. Independent auditing may hecome more intrusive. While understandable in a market context, it reflects poorly on the profession. More substantial effort in public communications can improve the credihility ofthe industry and equip practising mine ceolouists for snider responsihility.

Jan 1, 1997

By K-S Kim, C-Y Kim, D-G Kim

In tunnel construction or other underground construction, a detailed knowledge of the rock mass ahead of the face is essential for both safety and efficiency of work. Many tunnel collapses have been reported to occur because of lack of appropriate information, such as the geological conditions ahead of the tunnel face. One of the methods which can identify rock mass conditions is the application of drill monitoring data obtained from blasting drill holes, which can detect abrupt and unexpected changes in ground conditions, geological structure and the mechanical and physical properties of rock mass. This paper presents a new approach to how drill performance parameters can be used for prediction of geological conditions ahead of tunnel face. The predictions are based on monitoring the drill parameters of instantaneous advance speed, torque and tool pressure. In order to assess conditions ahead of tunnel face, tunnel seismic profiling (TSP) and a horizontal boring investigation were undertaken and the obtained data compared to the drilling data. The predicted results using drilling performance parameters correlated well with geological conditions ahead of tunnel face.

Jan 1, 2008

The mIning operations of Bougainville Copper Pty. Limited are located at Panguna on the Island of Bougainville which is part of the Territory of Papua and New Guinea.C.R.A. Exploration Pty. Limited first established mineralization in the Panguna area in 1964. Exploration work since then has established ore reserves estimated to be 900,000,000 long tons of ore assaying 0·48 per cent copper and 0·36 dwt/ton gold. An economic feasibility study completed in July, 1969 enabled a decision to be made to proceed with a major mining operation. The ore will be mined by open cut methods and will be treated in a conventional concentrator with a nominal capacity of 90,000 short tons/day. The concentrate will be pnmped as a slurry through a 16 mile long pipeline to a port established on the east coast where it will be filtered and dried ready for export. Other supporting facilities for the mine include two towns, a 135 MW steam power station, and access roads.

Jan 1, 1971

By B Lyne

In 1990, the Queensland mining industry had come to the conclusion that new safety and health legislation based on risk identification and control was required if the mining industry was to be effectively and efficiently regulated. In particular stakeholders in the coal mining industry had arrived at this opinion after the industry had suffered a number of major underground explosions over the 14-year period between 1972 and 1986. Also by 1990, a general consensus had emerged across both the coal and metalliferous mining sectors that mining industry was over regulated and, more to the point this over regulation did not encourage industry to identify and address the underlying causes that had led to a cycle of major mining accidents in the state. The prevailing opinion was that the prescriptive legislation left the ownership of risk management with the regulator and not with the mine operator. This paper discusses the background to the development of the Queensland Coal Mining Safety and Health Act 1999 and the Mining and Quarrying Safety and Health Act 1999 and the progress made in improving safety and health since the statutes came into force on the 16 March 2001. The paper discusses the issues that had to be addressed during the development of the legislation including the interaction with other legislation based on based on risk management principles that either overly or interface with the mining legislation. The effect the underground explosion at Moura No 2 in 1994 had on the final content of the new legislation is also considered. Health is often the neglected twin of safety and health legislation and the paper previews the health surveillance system being proposed in Queensland to ensure that health of mine and quarry workers is afforded the same priority as their safety. By increasing the structured management of occupational health problems in our mines there is an opportunity to make significant improvements in mine safety In conclusion the paper reviews the results to date since the introduction of the new mining safety and health legislation in Queensland on the 16 March 2001. Progress has been made and more is yet to be achieved

Jan 1, 2003

By J Walasiak

In the climate planning of mines and tunnelling with anticipated poor climatic conditions, and especially in case of longer working shifts, the main question is whether it can be reliably prevented that certain climatic limits laid down be exceeded. Working at high temperature and/or humidity can lead to reduced human working energy û a very important economic aspect û and to a risky lack of concentration on the part of the miners or to heat collapse and extremely dangerous heat stroke. With the Deutsche Montan Technologie GmbH (DMT) climate prediction programs, both the dry and the extremely significant humid heat transfer can be calculated. This is due to the high planning reliability involved. With the help of these climate prediction programs it is already possible to determine the anticipated climatic values for the operation phase as early as the planning stage of new ore or coal fields or of tunnel construction projects and to design the optimum air cooling system for every underground project with due regard to technical and economic aspects.

Jan 1, 2005

By Choulaj D

Mining and petroleum continue to be the two most vita components of our nation's development, says Sir Julius Char in the Australian Journal of Mining (Nov-Dec 1996). In fact the} account for 71.6% of export earnings, and 21.2% of Gros; Domestic Product in Papua New Guinea. The Misima and Porger, Mines, along with the Kutubu oil project, have essentially rescues PNG's economic viability since the loss of income from Panguna Though the industry cannot create employment in the manner o. intensive industries such as agriculture, it does provid( opportunities to local communities in terms of jobs, financia compensation, and infrastructure. Many ventures take many years and enormous capital investment to set up. There are three phases: exploration, feasibility, an( operations. The operations phase sees a massive development o infrastructure, or the actual `building' of the mine. For mining companies to commit to such lengthy time frames and high level: of investment, without returns, requires confidence and a degree of commitment from government on a number of levels - legislative stability, monitoring social development, and the provision o social infrastructure.

Jan 1, 1997

By N Ross, N Goldup

In recent years the heavy mineral mining industry has started to look more closely at the feasibility of mining moderate to high slimes deposits. During the initial stages of orebody evaluation the primary purpose of the pilot plant is to produce heavy mineral concentrate for metallurgical evaluation. Hence, generally little consideration is given to the disposal of the waste material (slimes and tailings). This paper suggests additional, simple, low-cost, tests that can easily be incorporated into an initial pilot plant operation. With this data a more definitive evaluation of available waste disposal options can be made during the early stages of the project. Thus, permitting better project focus and utilisation of resources. These tests include free settling of slimes, natural slimes drying and consolidation (undrained and drained), tailings stacking angles, and particle size distributions of input and waste streams, etc. The objective and method of each test is summarised, together with its relevance to possible waste disposal options. The results of this preliminary testwork can later be used to expand upon and define further tests for the second phase of pilot plant operations, which will enable a more definitive evaluation of a proposed waste disposal solution.

Jan 1, 2001

By A E. Waltho, W J. Shaw

Predicting the physical characteristics of various ore types has for long been a difficult problem during mining. Grade control practices tend to concentrate on the chemical grade of the ore. Estimation of physical characteristics such as beneficiation behaviour is commonly limited to the simplistic application of historical averages. Large amounts of geochemical data are often gathered during the exploration and mining stages of a project, especially in ferrous and base metal deposits. In addition to the elements of principal economic interest, samples are often analysed for suites of gangue constituents to determine whether the mineralisation lies within target specifications. This multi-element data is often put to no other use than this simple chemical classification, yet it may present the geologist or metallurgist with valuable insights into the mineral content and physical characteristics of the deposit. Normative mineral estimates have been used as a method for characterising igneous rocks for almost 100 years. The method establishes and applies a set of sequential rules, by which the chemical components of a sample are assigned to mineral components. Provided that it is possible to make some realistic assumptions about the mineral species likely to be present in a rock unit or deposit and their paragenesis, this approach can be extended to a variety of mineral deposits. The geochemical data that are routinely collected when, for example, drilling iron ore and base metal deposits, can be used to derive estimates of normative mineral content. These estimates can be used to characterise physical or metallurgical aspects of the ore, such as density, beneficiation behaviour and metal recovery. This paper examines the application of normative mineral estimates to a variety of practical resource characterisation problems. The potential for predicting the lump and fines proportions of iron and manganese ores is also discussed.

Jan 1, 1999

By R Valenta

Most developing projects face a range of technical and non-technical challenges, and examination of development histories can potentially provide insights into improved approaches to project development. The Kestanelik project in the Canakkale region of Western Turkey was acquired by Chesser Resources Ltd in 2008. Turkey is a significant and growing source of gold production, with sector participation by both domestic and international companies. While the broad ranges of challenges faced by developing projects is well known, there are relatively few case studies in which the range of technical, environmental, social and governance challenges are presented in a single contribution. Recent studies of undeveloped complex orebodies have particularly shown the extent to which environment, social and governance (ESG) complexities contribute to project delays and failures. The Kestanelik project faced a full range of technical and ESG complexities, and provides an illustrative example of the associated challenges. CITATION: Valenta, R, 2018. A case study of technical, social and environmental challenges for a gold project development in Western Turkey, in Proceedings Complex Orebodies Conference 2018, pp 73–74 (The Australasian Institute of Mining and Metallurgy: Melbourne).

Nov 21, 2018

All companies and individuals who embark on a business venture incur costs. For the most part these costs can be conveniently categorised, firstly into capital and operating costs and then into the various elements of these major cost centres. Although the nature of expenditure naturally differs as between industries certain broad cost types are characteristic of all heavy industries. The capital costs of gaining access to an orebody, equipping a new mine, building a treatment plant and perhaps refining and smelting facilities are likened to capital expenditure by a manufacturer on new plant and equipment required for an expansion or new product innovation. Similarly the day to day costs of labour and materials employed in the running of a mining operation can be likened to similar costs in other heavy industry. There is another group of costs that are not so easily categorised. Most industries incur unavoidable costs that do not form part of the direct or capital costs of physical production. These costs include taxes and other payments to government and research expenditure. The mining industry has a particularly heavy burden of non-production costs and it is the objective here to highlight and analyse a few of them. These costs are exploration expenditure, infrastructure expenditure, royalties and income tax. This is not to suggest that these are the only major non-production costs that the mining industry needs to bear. The industry may incur significant costs for environment protection, land tenure maintenance and on liaising with Government on a wide variety of matters. It is for reasons of subject manageability that the list is confined to the four costs mentioned. For the mining industry, exploration and infrastructure expenditure, royalties and income tax have several distinguishing features. Firstly, they are generally proportionately large costs. Exploration and infrastructure expenditure for example, could well exceed mine development costs. Depending on how royalties are levied, they may be very high in relation to profits earned and many in fact exceed profits. Secondly, except for income tax, they are costs that are generally not payable by other industries. Exploration expenditure is in some respects comparable with industrial research and development. However, because mines are wasting assets exploration is necessary for survival, and it is likely to form a larger part of costs per dollar of profits or sales than R&D. It can therefore be said that exploration is of far more significance to the miner than R&D is to the typical industrial company. Furthermore, unlike exploration expenditure, R&D results are transportable and patents permitting, transferable. The infrastructure burden that miners must carry is unique to the industry. Whereas urbanised industry is not usually liable for the capital cost of power, water, transport, townships and community facilities, the miner must finance these projects himself. Neither the payment of royalties, nor of course, income tax are unique to the mining industry. Royalties are more properly described as a unique charge on some primary industries but however described, they are a charge that manufacturing and service industries do not have to pay. Whilst we all pay income tax, the mining industry's uniqueness derives from the special problem that the industry has in arriving at annual net income in view of the capital intensity of the industry, partly due to expenditure on infrastructure, the indefinite life of capital equipment and its unpredictable residual value, funds expended on exploration and long lead times associated with a mine development. The third distinguishing feature of these costs is that, with the possible exception of exploration expenditure, they are heavily influenced by the policies and actions of Government. As such the industry has a responsibility to promote the industry by emphasising its potential to improve national product including exports and by requesting that the Government provide for the industry in its long term planning and seek its co-operation to prevent the industry incurring inequitable penalties relative to other industries.Finally, exploration and infrastructure expenditure are significant because they are front-end charges on a project. When due allowance is given the time value of money and the deferment of income from a mining development to which they relate, exploration and infrastructure expenditure assume greater importance than the raw money expenditure suggests. For all these reasons, exploration and infrastructure expenditure, mining royalties and mining income tax are worthy of detailed study. This is the purpose of this paper. The objective is to examine the determinants that give rise to them and provide some thoughts on their impact on on-going and potential mining developments and, where relevant, to make some suggestions as to how they may be minimised.

Jan 1, 1977

By J Leppinen, B Johanson, R Kalapudas, G McMahon

The Suurikuusikko gold deposit was discovered in 1987 in western Finnish Lapland, 54 km NNE from the town centre of KittilS in the volcanic belt of Central Lapland. It is hosted by tholeiitic basalts in a graphite-bearing albitite breccia. The ore is located in subvertical shear zones characterised by strong albitisation, carbonatisation and sulfidisation. The ore minerals consist of arsenopyrite, pyrite, chalcopyrite, sphalerite, tetrahedrite, bournonite and rutile. Small amounts of pyrrhotite, gersdorffite, jamesonite, bornite, gudmundite, tetrahedrite, stibnite, kermesite, berthierite and native Sb are also present. Gold occurs as invisible and as 1 - 2 ¦m size inclusions in arsenopyrite and pyrite, on their grain boundaries and in fractures. The average amount of gold leached by cyanide is 2.93 per cent. The æinvisibleÆ gold contents were studied in pyrite and arsenopyrite by electron microprobe analysis (EPMA) and secondary ion mass spectrometry (SIMS) at CANMET/ MTL. Gold element distribution images show zoned patterns both in pyrite and arsenopyrite. SIMS analyses range from 343 to 55 ppm Au in arsenopyrite and from 217 ppm down to 0.32 ppm (detection limit 478 ppb) Au in pyrite. EPMA results range from 939 to below the detection limit 24 ppm Au in arsenopyrite and from 267 ppm to below 22 ppm Au in pyrite. Recovery of the refractory gold ore was studied using grinding, flotation, bio-oxidation and cyanidation tests. A sulfide bulk concentrate containing 40 ppm Au was obtained by flotation at 90 per cent recovery (As content 5.5 per cent, S content 22 per cent, and mass recovery 15 per cent). The grinding fineness in flotation was P80 -100 to 120 ¦m. At the original fineness the cyanidation recovery from the concentrate was lower than ten per cent, after ultra-fine grinding P80 -10 to 2 ¦m the Au recovery was less than 17 per cent. After bio- oxidation, Au recovery of 95 per cent was obtained in carbon-in-leach (CIL). The bio-oxidation time was two weeks in laboratory test, but after regrinding the oxidation rate was faster and recovery of Au higher. However, the selected method for the mining to be started in summer 2008 is open pit mining and mineral processing methods sulfide flotation and pressure oxidation in an autoclave. The ore reserves were estimated 31 December 2007 as: Probable 18.2 Mt with 5.1 g/t Au, Indicated 5.4 Mt with 3.0 g/t Au and Inferred 10.8 Mt with 3.4 g/t Au. The production capacity will be 3000 t/day.

Jan 1, 2008