Search Documents

By L Nicholls, A Parbhakar-Fox

Reprocessing Queensland’s historical copper tailings for critical minerals is an opportunity to circularise the state’s mining industry by converting waste liabilities into assets. Mine waste valorisation enables economic rehabilitation of legacy mining sites, improves environmental outcomes, and can establish a secondary resources sector that produces a sustainable supply of critical minerals to supplement growing global demands (Australian Government, 2023). The North-West Queensland Minerals Province (NWQMP) hosts numerous copper mines with known cobalt mineralisation (Degeling, 2020). Cobalt is a critical metal essential for green energy and battery technologies, however its global supply is at risk due to geopolitical and ethical concerns (Rachidi et al, 2021). Historically mining in the NWQMP has focused on copper, leaving cobalt to theoretically accumulate in the mine waste. First-pass geometallurgical characterisation of waste repositories by the Sustainable Minerals Institute identified Capricorn Copper as a key site for further investigation into cobalt deportment and recovery potential.

Aug 2, 2023

By E Bouchard March, F Lavoie, B Legare, K Bourassa

Quebec Iron Ore (QIO), a subsidiary of Champion Iron Limited (Champion), completed the restart of the Bloom Lake iron ore mine located in the heart of the Labrador Trough region of Northern Quebec, Canada in February 2018. Prior to its restart, the concentrator flow sheet underwent major upgrades which brought the iron recovery to the highest of all Labrador Trough operations. After two profitable years of production, QIO, supported by Soutex, started to look at technologies to improve its current performance and integrate into its expansion project flow sheet. From the lessons learned while optimising Phase 1, the addition of a scavenger-cleaner processing stage was identified as an improvement opportunity to increase recovery, produce a higher-grade product, and further improve the stability of concentrate quality. In 2019, the NI-43101 feasibility study for the Phase 2 expansion, aiming to double the production of high-grade iron ore concentrate, was published. Based on the metallurgical test work, the hydraulic classifier was selected to perform the scavenger-cleaning duty for its well-established performance and known behaviour at the cleaning step in the Phase 1 plant. To validate laboratory results, a pilot scavenger-cleaning hydraulic classifier was installed in Phase 1. Although the hydraulic classifier was selected for the feasibility study, metallurgical test work performed with the REFLUX® classifier showed interesting potential. It was thus decided to also install a pilot RC300 Reflux classifier at the scavenger-cleaning stage in Phase 1. Despite their apparent great similarities, the metallurgical performance was significantly different, and many dozens of sampling campaigns highlighted the different performance of both pieces of equipment considering the feed material particle size. This article presents the pilot plant results in terms of recovery, selectivity and stability for both the Reflux classifier and the hydraulic classifier operated in a scavenger-cleaner stage at the Bloom Lake iron ore concentrator.

Nov 8, 2021

By S Tyrrell, B Jackson, K Matson

Northern Star Resources Limited Jundee Gold Mine in Western Australia operates a comminution circuit that consists of a primary crusher, 3.85 MW semi-autogenous grinding (SAG) mill, 1.8 MW ball mill and pebble recycle crusher. In 2017, a secondary crushing circuit was installed to remove the SAG mill throughput bottleneck and increase production of highly competent underground ore from 1.35 to a minimum of 1.7 Mt/a.This paper discusses the findings from the trial phase, the circuit design, project delivery, site optimisation, and the plant performance.CITATION:Matson, K, Tyrrell, S and Jackson, B, 2018. The application of secondary crushing at the Jundee gold mine, in Proceedings 14th AusIMM Mill Operators' Conference 2018, pp 485–496 (The Australasian Institute of Mining and Metallurgy: Melbourne).

Aug 29, 2018

By D Veneziano, J Van Dyck, R Snow, W Pytel, O Zanoli

Best practice standards generally recommend assessment of the environmental and societal risks posed by tailings storage facilities, but they rarely specify how the analysis should be made. As a case study, this paper describes a safety assessment of the Zelazny Most tailings pond operated by the Hydrotechnical Unit of KGHM Polska Miedz SA in Poland. The complete assessment includes a failure mode effect criticality analysis (FMECA) that considers all conceivable failure modes, but this paper focuses on one key mode, the loss of stability during the planned raising of the crest above its current level. Reliability against static dam failure considers uncertainty on the safety factor in a limit equilibrium approach. The threat of dynamic (earthquake induced) instability is assessed by developing a model of future seismicity as a function of the mining plan and considering uncertainty on the induced permanent displacements along critical sliding surfaces. We quantify the additional level of protection against outflow provided by the beach using an event tree with expert-assigned probabilities. Continuous monitoring of the dam for premonitory signs of instability and a set of loss-prevention plans in the case of a spill provide additional layers of protection; their effectiveness is quantified by estimating the fraction of the population that could be evacuated as a function of warning time. The probabilistic analysis indicates that the safety targets are met and produces practical recommendations on how to maintain and improve the safety level while the dam crest is raised above its current level.CITATION:Van Dyck, J, Pytel, W, Veneziano, D, Snow, R and Zanoli, O, 2015. Safety of a tailings storage facility against dam instability, in Proceedings Tailings and Mine Waste Management for the 21st Century , pp 253–262 (The Australasian Institute of Mining and Metallurgy: Melbourne).

Jul 27, 2015

By M Berry

Consider these four questions:What is the definition of life-of-mine?When should life-of-mine planning seriously commence?When can life-of-mine planning seriously commence?What is the key input to effective life-of-mine planning?Whilst there is likely to be general consensus on the answers to the first three questions, the answer to the fourth question is open to debate. This author argues that understanding and managing risks and opportunities associated with geological uncertainty is the key input to effective life-of-mine planning, at all stages in the life cycle of a mining project.CITATION:Berry, M, ?2014. Effective life-of-mine planning by understanding and managing risks and opportunities associated with geological uncertainty, in Proceedings Life-of-Mine 2014 , pp 183–190 (The Australasian Institute of Mining and Metallurgy: Melbourne).

Jul 16, 2014

By I B. Miller

Magnesium International Limited (MIL) has broken new ground in their desire to integrate their mineral development activities in the Southern Flinders Ranges of South Australia in to the communities of the region, despite there being no statutory requirement to do so. In their efforts to define a magnesite resource adjacent to the proposed site for a magnesium metal processing facility, MIL opened their exploration program up for public consultation. In conjunction with the Port Pirie Regional Development Board (PPRDB), a community group was formed to review the impact of exploration and mining on the ecologically sensitive Southern Flinders region. This voluntary move towards full community consultation for mineral exploration was a first in South Australia and probably in Australia. The Community Focus Group (CFG) worked closely with MIL, Primary Industries and Resources of South Australia (PIRSA) and the Department for Environment and Heritage (DEH) in the development of an exploration program and Declaration of Environmental Factors (DEF) acceptable to all stakeholders. Collaboratively, the community concerns were discussed and addressed, with the community gaining a very comprehensive understanding of the exploration process and possible future mine development. A balance of social, environmental and economic factors was developed that was accepted by all parties and encapsulated in the final DEF for approval by the regulatory authority. The consultation process was a new experience for all of the stakeholders, each of them effectively exploring new ground in addressing information dissemination, risk management and the social versus economic equation. MIL developed not only a viable and acceptable exploration program but also substantially reinforced its position as a responsible corporate citizen with the Southern Flinders communities.

Jan 1, 2004

By N Ganjian, A Delavar, F Rashidi Nejad

Iran is one of the most seismically active countries in the world, being crossed by several major fault lines that cover at least 90 per cent of the country. As a result, earthquakes in Iran occur often and are destructive. So, it is important to consider the seismic stability and reliability of all structures including tailings dams.In this study, the tailings dam stability of the Sangan Iron Ore Mine in Khorasan Razavi, Iran is considered for the case study. The tailings storage facilities of the mine have three cells with the capacity of 45 million cubic metres. The first cell, which has three stages of dam raising, has been recently brought into operation. This cell has a downstream-raised retaining embankment. As the risk of seismicity in this area is high, seismic response of this dam was evaluated by numerical methods. To do this, appropriate models were developed for materials used in foundation and body of the embankment. Then for seismic stability analysis, Tabas (Iran – 1978) and Chi-Chi (Taiwan – 1999) earthquake acceleration simulations were applied.The results of this study indicated that the upstream portion of Stage 3 of the dam and dam crest did not experience significant horizontal displacements during earthquake period, but the downstream portion of Stage 3 of the dam showed a maximum horizontal displacement of 60 cm at the third stage of dam raising. This is three times more than what was estimated by the designer. Also, the maximum vertical displacement resulting from simulation of the Tabas earthquake was 35 cm. The results of dam response to Tabas and Chi-Chi earthquakes indicate that displacement, shear stress and pore pressure by the Tabas earthquake were higher than the case of Chi-Chi earthquake. The higher energy of Tabas earthquake and the higher frequency near to the natural frequency of Tabas earthquake could be the reasons of this difference. The results of this case study confirm that if the studied tailings dam impacted by an earthquake of a similar magnitude to Tabas, the dam will be seismically stable and the developed strains will not be significant.CITATION:Delavar, A, Rashidi Nejad, F and Ganjian, N, 2015. Seismic stability analysis of Sangan Iron Mine Project tailings dam, in Proceedings Tailings and Mine Waste Management for the 21st Century , pp 173–182 (The Australasian Institute of Mining and Metallurgy: Melbourne).

Jul 27, 2015

By D G. Rantucci

Organic carbon is a major ore contaminant at MMG’s Century mine. This carbonaceous matter is associated with shale hosted sphalerite mineralisation. It occurs as elongated lamellae and as inclusions in porous sphalerite aggregates which are fine grained and difficult to liberate from sphalerite. The carbon prefloat circuit was designed to remove the liberated organic carbon in order to mitigate excessive reagent consumption, contamination of the lead and zinc concentrates and poor flotation performance in the primary zinc circuit. The consequence of organic carbon removal is that sphalerite and galena minerals are lost to the prefloat concentrate. A Jameson Cell was installed in late 2005 as a prefloat cleaner cell. Operational experience showed that the cell became capacity limited during periods of high amounts of organic carbon in the feed and was subsequently bypassed.Reactive style operating strategies were implemented to manage the effects of insufficient organic carbon removal by the prefloat circuit but due to the relatively large circuit residence time, upstream changes meant hours before the downstream circuits were stabilised following a disturbance from excess carbon.This paper describes the modifications and testwork undertaken to enable the Jameson Cell to be operated during periods of high organic carbon in the float feed and the implementation of process control initiatives to proactively remove the required prefloat mass from the float feed to eliminate the reactive style operating strategy.The process control modifications centred on dynamically targeting a prefloat mass recovery determined by an equation relating the carbon to zinc ratio to the carbon prefloat mass as a percentage of the float feed. The equation was developed by analysing historical data. These improvements served to optimise the prefloat circuit and consequently stabilise the downstream lead and zinc circuits.

Aug 8, 2011

By F K. Altuntov

The study presented in this paper is based on the Kiirunavaara underground mine located in the northern part of Sweden. The deposit is mined using the sublevel caving (SLC) mining method. This paper briefly reviews the alternative SLC layouts, as well as presents challenges for the application. In Kiirunavaara currently, the traditional SLC design is employed, however, continuous improvement of material transportation systems used in mines generates a need for investigation of the current and future production area layouts in sublevel caving mines. When identifying the potential benefits of the alternative production area layouts, the production targets and effects must be further investigated to understand the benefits and potential effects. In this study, several different layouts have been investigated and evaluated. The designs include different development configurations and orepass infrastructure moved further away from the orebody and still require further investigation.

Mar 29, 2023

By C Hawtin, B Miller, D Ashton

Ernest Henry mine (EHM) is an Iron oxide copper-gold sublevel cave mine located 30 minutes north of Cloncurry in North-West Queensland. The underground mine lies beneath open pit excavations, which were in operation from 1999 to 2011. Fault structures carry large quantities of water from the cover sequence aquifer into the underground mine area. The open cut excavations exacerbates vulnerability of the underground mine to the high intensity wet season storms of northern Queensland. These factors combine to make hydrogeological issues high priority for mine operation. Water-related risks include the cost of removing water from the mine, flooding risk and mud rush potential.Turnover of key technical staff in late 2015 at EHM resulted in the mine being left in an untenable position of losing the primary source of technical knowledge. Due to encouragement of cross-disciplinary activity coupled with workload and resource sharing, the management team were confident in utilising on-site personnel to offset loss of experienced personnel.Remaining geology personnel took additional responsibility for hydrogeological monitoring equipment and planning of upcoming work. Consultant input was limited to review only and an emphasis was placed on knowledge transfer to the geology team. Using this strategy, a 13 hole dewatering program was successfully implemented, achieving a significant water level drop in areas of elevated hydrological risk, whilst also upgrading the hydrological monitoring sensor array.Through a development program centred on cross-disciplinary exposure, the technical team was able to retain key technical knowledge despite staff turnover and produce strong results outside traditional training and roles. This paper serves as a case study on the methods, strengths and drawbacks of putting a focus on cross-disciplinary exposure as a method to combat staff turnover.CITATION:Ashton, D, Miller, B and Hawtin, C, 2017. Go with the flow – managing hydrogeological staff turnover at Ernest Henry mine, in Proceedings Tenth International Mining Geology Conference 2017, pp 129–136 (The Australasian Institute of Mining and Metallurgy: Melbourne).

Sep 20, 2017

By Muldoon T

Water sprays on mining machines are generally put there to reduce dust; however, research by the Bureau of Mines and others has shown that considerable airflows may also be generated by these sprays. This recognition of water spray-gen- erated air movement led to the "Spray-Fan" - a continuous miner auxiliary ventilation system which was shown to reduce methane peaks by a factor of 15. Recent successes and failures of the Spray Fan are reviewed. More recently, the same principles were used in the design of the "Shearer- Clearer" for reducing dust at longwall shearer operators. The original design was successful; however, a new design is now available which is more practical to install and does a much better job of holding the dust against the face downwind of the shearer. The latest research objective is to eliminate the negative impact of spray- generated air turbulence on continuous miner dust control. Most coal faces in the USA are ventilated in the exhaust mode using "line curtain", and the forward airflow on the side of the heading opposite the curtain is inevitably weak. Air turbulence generated by sprays which are incorrectly located and/or operated at excessive pressures can cause roll back - in which the dust cloud at the face is forced unwind against the ventilation and spreads over the miner cnerator. The general approach to reducing "roll back." is reviewed and art anti-roll back water spray system is presented.

Jan 1, 1983

By W Newns

This paper describes laboratory and in situ tests and determines a set of parameters for stiffness and strength properties for a weak sedimentary rock mass, the East Coast Bays Formation of Auckland. The parameters derived are discussed in relation to peak strength and in respect of deformation limits associated with sequential excavate and support (SEM) or conventional tunnelling.

Mar 8, 2011

By L Klemettinen, J Biswas, W Malan, D Sukhomlinov, D Lindberg

In order to mitigate the effects of climate change, our society must be able to drastically reduce its CO2 emissions. As the metallurgical industry is a considerable contributor to these emissions, new greener technologies must be invented and developed. One option could be the direct production of metals from oxides using renewable electricity. The aim of this study was to investigate the possibility of using high-temperature molten oxide electrolysis (MOE) for iron and ferrochrome production. FactSage™, ver 8.2 (by Thermfact Ltd and GTT-Technologies) was utilised for estimating a feasible equilibrium electrolyte composition, and the experiments were conducted at 1550–1580°C in conical alumina crucibles with iridium wire as the cathode and platinum wire as the anode. The sources of iron and chromium were either pure FeO powder or industrial chromite pellets. Voltage was applied to the electrolysis cell for 6 hrs and the resulting current was measured, along with oxygen concentration in the off-gas line. The electrolyte comprised of SiO2, Al2O3, MgO and CaO. First, the effect of FeO concentration on iron reduction efficiency was investigated using only pure oxide powders as starting materials. The results indicated that 10 wt per cent FeO mixed with the electrolyte resulted in more efficient iron reduction compared to 20 wt per cent. In further experiments, industrial chromite pellets were ground and mixed with the CaO-free electrolyte. Iron and chromium reduction efficiencies were higher when approximately 19 wt per cent of the total sample mass consisted of pellets compared to increasing the pellet amount to 37 wt per cent. Generally, the chromium solubility in the liquid electrolyte was relatively low, and most of the chromium was confined to the spinel solid solution, from where its dissolution to the liquid electrolyte was very slow, resulting in slow reduction kinetics. For larger scale applications, economically more viable electrode materials should be investigated.

Jun 19, 2024

There is an increasing demand for refrigeration as mines progress deeper. Mine refrigeration plants have special requirements in terms of their duty and application. There are no national or international standards applicable for the testing of these plants. There have been numerous examples of plants failing to meet their required nominal capacity, but with the plant owner being unable to enforce the design duty on the manufacturer, due to a failure to unambiguously specify testing or accepting criteria. This paper discusses some of the reasons for performance shortcomings and describes a methodology for developing and specifying performance criteria, when inviting design and/or construction tenders, and a method of performance and acceptance testing once the plant has been built and commissioned. These guidelines encompass the full range of performance duties expected from a mine plant, including stable operation at maximum and minimum plant capacity, and under the various combinations of extremes of high and low condensing and evaporating pressures. A description of a methodology for developing a computer-based mine refrigeration plant model is also presented as part of the performance testing criteria. The methodology is illustrated with reference to the actual performance and acceptance testing process used on the worldÆs largest bulk air cooler (R67) at the Enterprise mine at Mount Isa, Australia.

Jan 1, 2005

By D J. Brake

Most mine ventilation engineers are involved in ventilation planning and design in some capacity. Ventilation modelling software used by a competent experienced ventilation engineer is extremely useful in developing good ventilation designs by allowing assessment of a wide range of potential options. Unfortunately, ventilation modelling undertaken by persons who do not have sufficient experience or knowledge usually results in a façade that covers up a fundamentally unsatisfactory design. Ventilation models are produced for a wide variety of purposes including: fault-finding of a problem area in a mine and options analysis for resolution of such problems; a complete review or optimisation exercise of an entire mine’s ventilation system; or a much longer life-of-mine type of study. Models can be intended as the basis for studies with diverse purposes such as primary shaft or airway sizing, primary fan specification, examining re-entry times after blasting, resolving leakage or recirculation, or investigating the impact of fires or underground climate or cooling requirements. The concepts of ‘materiality’ and ‘fitness for purpose’ are essential to developing or using a ventilation model and serious mistakes have been made in wrongly using a ventilation model for purposes for which it was never intended, often because it is simply the most recent model on the mine site. Mistakes at this level often translate into faulty ventilation strategies and inefficient or ineffective use of scarce capital for ventilation projects. Validating a ventilation model is a time-consuming and expensive process and not every model must (or even should) be fully validated to meet the objectives at that time. This paper discusses the application of quality assurance in ventilation planning with particular respect to the ‘basis of design’ (BOD) as well as the standards for validating a ventilation model. It also provides a recommended way of dealing with non-conformances in measured versus modelled values of critical parameters in the model.CITATION:Brake, D J, 2015. Quality assurance standards for mine ventilation models and ventilation planning, in Proceedings The Australian Mine Ventilation Conference, pp 221–228 (The Australasian Institute of Mining and Metallurgy: Melbourne).

Aug 31, 2015

By M L. Cramer, N P. Wines

"On 9 February 2014, bushfire embers landing on exposed coal in a disused pit at the Hazelwood mine in Victoria’s Latrobe Valley ignited a coal fire that burned for 45 days. The fire was the largest and longest burning mine fire to occur in the Latrobe Valley (Hazelwood Mine Fire Board of Inquiry, 2016). Two Victorian Government Boards of Inquiry have been held into the Hazelwood mine fire. The most recent, in 2015, included consideration of the regulation and implementation of rehabilitation practice at Hazelwood and the other two brown coalmines of the Latrobe Valley (Loy Yang and Yallourn; Government Gazette, 2015).The 2015 Hazelwood Mine Fire Board of Inquiry commissioned Accent Environmental Pty Ltd (Accent) to undertake a review of the financial mechanisms for mine rehabilitation and closure adopted in Australia and overseas (Accent, 2015). Specifically, Accent was engaged to identify ‘any practical, sustainable, efficient and effective alternative mechanisms to ensure rehabilitation of the mines as required by the [Victorian] Mineral Resources (Sustainable Development) Act 1990’ in accordance with Terms of Reference 10 (c) (Government Gazette, 2015).The review by Accent included consideration of a range of financial instruments such as bank guarantees, trust funds and insurance. It considered a number of financial assurance systems in operation in Australia, New Zealand, the European Union, Canada and the United States. These systems included: full and discount financial assurance systems predefined liability proportion systems pooled fund systems the use of post-closure financial mechanisms such as trust funds (Accent, 2015).What lessons can be learnt from other jurisdictions? Are there financial mechanisms already in place that could allow the Victorian Government and the mine operators to manage the risk of rehabilitation default3, lower rehabilitation liability, attain site rehabilitation objectives and allow eventual site relinquishment?CITATION:Cramer, M L and Wines, N P, 2016. Global lessons for a local problem – rehabilitation bonds and Victoria’s Latrobe Valley coalmines, in Proceedings Life-of-Mine 2016 Conference , pp 24–27 (The Australasian Institute of Mining and Metallurgy: Melbourne)."

Jun 28, 2016

By A D. Caccioppoli

Grade control systems within Rio Tinto Iron Ore have proven to be robust, when mining full benches. The Hope Downs 1 operation hosting two Marra Mamba Iron Formation deposits (North and South Deposits) presents a new challenge, where increased mining selectivity due to moderately plunging N-verging folds has made flitch mining necessary in the South Deposit. Poor flitch blasthole sample duplicate results in South Deposit over a 12 month period, compared to North Deposit, have highlighted concerns with grade predictions. In contrast a new grade control methodology (grade splitting) was proposed to alleviate blasthole sampling bias, utilising geological mapping and mineralogical logging, currently practised throughout Rio Tinto Iron Ore Pilbara operations, to estimate theoretical grades for each flitch from a single blast cone assay. To assess this method, reverse circulation holes (RC) were twinned to blastholes establishing an ‘actual’ grade. These blastholes were assayed using current flitch sampling techniques where: flitch positions were estimated, flitch positions were marked with paint, and a full cone sample was taken for ‘grade splitting’. Using these data sets multiple grade predictions were produced, then analysed using Half Absolute Relative Difference (HARD) statistical analysis. In addition to testing these grade control methodologies two other findings were ascertained: an inherent bias in blasthole assays exists particularly in the top flitch, where an average absolute difference of 0.6 per cent in SiO2 and 0.42 per cent Al2O3 was measured; and assays derived where kaolin rich soft shales are intersected were less representative. This is likely to be due to these materials not being properly represented in blast cones. Grade splitting accurately estimated block chemistry, except for a slight under-prediction in Al2O3 and P compared to current grade control methodologies. This method is a viable alternative where grade distribution is stratigraphically controlled.

Aug 22, 2011

Although this is a symposium on "The Occurrence, Preparation and Use of Australian Black Coal", I do not think that, in these days, any of the main energy resources can be considered only in terms of country of origin or only by itself in isolation from other energy resources. Accordingly, I propose to comment on solid fuels generally in the world energy scene, and make some brief references to Australian solid fuels, and to some other matters in the latter part of this paper. In this address I am drawing heavily on the 1974 survey of energy resources published just recently by the World Energy Conference. I do this for a number of reasons. Firstly, the survey is the latest and most comprehensive publication of its kind; secondly, it is the result of several years' work by a panel of eminent people, from all the energy industries and from some 16 widely spread countries; thirdly, substantial assistance was given by the U.S. Atomic Energy Commission in its compilation; and, finally, to let all know of the existence of the book, as I believe it to be a source document for all those interested in world energy resources. The United Nations "J" series of statistical papers provide important information on the annual production and consumption of and trade in the various forms of energy. In their respective areas, these two publications are primary information sources. Our present sources of energy throughout the world are fossil fuel deposits (coal, oil, gas), nuclear materials, water, geothermal, solar and tidal - but we are at present heavily dependent upon the natural stores of non-renewable fossil energy resources. Fig. 1 shows the changing use of energy resources in the present century. A comparison between 1900 and 1973 shows clearly the shift which has taken place.

Jan 1, 1975

By K Ehrig, V Liebezeit, E Macmillan

The results from metallurgical test programs are used in feasibility studies for design of new plants and brownfield expansions, in long term mine plans, and to make decisions in an operating plant. There are many elements which contribute to a well-constructed test work program. Ultimately, understanding the accuracy and precision of the test work results is critical to ensuring good decision-making at various phases of a project.Every resource drilling and associated assaying program will have a quality assurance / quality control (QA/QC) component, however this often seems to be overlooked in metallurgical testing programs. The principles of “international standard” or “certified reference material” samples and replicate/duplicate testing can be applied to metallurgical programs, although there are metallurgical-specific considerations in both generating and analysing the data.This paper will describe the QA/QC program carried out within the Olympic Dam geometallurgy program. It will present results in the form of case studies from ten years of testing of replicates and bulk reference samples for industry-standard comminution tests as well as laboratory flotation and leaching tests. The Olympic Dam geometallurgy quality control program has enabled quantification of the precision of metallurgical testing and improved our understanding of the best possible modelling results given the underlying dataCITATION:Ehrig, K, Liebezeit, V and Macmillan, E, 2017. Metallurgical QA/QC – who needs it? The Olympic Dam experience, in Proceedings MetPlant 2017, pp 31–44 (The Australasian Institute of Mining and Metallurgy: Melbourne).

Sep 11, 2017

By J Wheeler

The objective of this paper is to examine the operation of high frequency screens in closed circuit grinding, where the outcomes achieved indicate favourable economic gains at the comminution stage and downstream processes, including flotation, dewatering, and filtration operations. The classification process in grinding circuits has been slowly evolving within the last century. The history of classification devices brings to mind rake classifiers and spiral classifiers, which although having higher efficiencies compared to hydrocyclones, were not able to keep pace with the evolution of concentrator equipment treating higher tonnages. This higher tonnage throughput has tended to drive the concept of utilising hydrocyclones as the classification stage in closed grinding circuits. The comminution process is commonly the most energy intensive stage of mineral processing. Researchers have determined that the classification stage in the comminution process has the greatest potential for improvement. This paper is intended to inform mineral process engineers of the benefits that high frequency screens offer over hydrocyclones. This will be done by reviewing the purpose for the evolution of classification in the comminution process, documenting past and recent studies, and explaining the modern technology that is currently available.

Aug 8, 2011