Search Documents

By d&apos, John C. Entremont

Pure iron was inductively melted in small refractory crucibles and optical pyrometer and immersion thermocouple readings were simultmzeously taken. The resulting emissivities of the liquid iron surface obtained were found to be greatly affected by both the gaseous atmosphere and geometrical changes in the physical setup. Quantitative values for these effects are indicated. FOR many applications in both the laboratory and plant, optical pyrometry is still the best means of measuring temperatures in the incandescent range. A prerequisite in evaluating the correct temperature is a good value of the emissivity of the surface. To obtain the emissivity from the tabulated values of the literature can be very confusing and often far from correct. There are many reasons for these difficulties, and it is not within the scope of this paper either to enumerate or to discuss them all. Its purpose is to show quantitatively how several factors affect the apparent emissivities obtained from experimental measurements on liquid iron surfaces. The black body is the reference state for the quantitative values of emissivities and is defined1 as a body which absorbs all radiation incident on it, reflecting none; such a surface emits more radiation per unit area per unit time than any surface which reflects any radiation, and is given a value of unit emissivity. All bodies having reflective power thus have emissivities less than unity and are considered nonblack or grey bodies. The ratio of the radiant energy emitted by the flat, nonblack surface to that of a perfectly black surface of equal area and temperature is the emissivity of the surface. The above definitions are applied to flat, polished, opaque surfaces, very seldom encountered in actual measurements, and for this reason many authors have suggested that the word "emittance" be used for real bodies rather than emissivity. The emittance has reference to the material and its configuration rather than to its properties in the idealized state. Recent observations of molten iron in a small refractory crucible indicate that not only the configuration of its surface but the geometrical arrangement of its surrounding and the nature of the surrounding atmosphere have a pronounced effect on the emittance. Neglect of changes in such conditions may lead to errors as large as 40°C at 1600°C. Thus it is suggested that the term "apparent emissivity" be used and that it be recognized that its value pertains to a particular experimental arrangement only. As a result of not recognizing these differences in emissivities, which are obtainable from changes in the physical setup of an observation, many investigators have incorrectly quoted their values as those of the emissivities of particular materials rather than as an apparent emissivity for their particular arrangements. As a consequence, values of the emissivity of liquid iron ranging from 0.3 up to 0.55 are found in the literature. In an effort to establish an accurate optical temperature scale for liquid iron solutions in which de-oxidation studies were to be carried out, it was observed that the temperature relationship, obtained by simultaneously taking immersion thermocouple

Jan 1, 1963

By L. G. E. Bignell

Surveying what was done in 1929 in meeting problems of oil-field equipment corrosion, one is struck by the fact that fewer meetings were held for discussion of these problems and fewer papers written than in any year since the subject engaged the attention of petroleum engineers. This does not mean that progress has not been made, for a great deal actually has been accomplished. Recommendations that accompanied field reports have been put into actual trial and some results obtained are gratifying. The type of papers prepared also has undergone a change, for they now deal with things accomplished rather than recite damages and suggest possible remedies. Some of the most notable work pointing the way for future solution of many pipe line problems is that done for the U. S. Bureau of Standards by Dr. K. H. Logan and Dr. Gordon N. Scott, dealing with tests of pipe coatings and reports on soil conditions. Many facts of great importance have been isolated and defined by these two men, not only indicating what may be done in some instances to retard corrosion, but showing that things formerly considered of importance have little bearing apparently upon the practical results. All-aluminum Storage Tanks In April, 1928, an all-aluminum 500-bbl. field storage tank was put into actual field use in Crane County, Texas, together with another tank of the same capacity but made with steel bottom and lower section of side sheets and aluminum upper ring of side sheets and deck. In April, 1929, after a little over one year's use these tanks were opened and examined by a group of engineers and chemists. The results of the test were enlightening. Other tanks made entirely of steel and used in the same battery with the two test tanks had some of their side and bottom sheets destroyed by corrosion in six to nine months, but the all-aluminum tank was in actual use for 18 months before holes were found corroded through the bottom, when the tank was examined for a second time in September, 1929. This field test of the aluminum tank confirmed the already known

Jan 1, 1930

By S. C. Geol, C. H. Page

INTRODUCTION Mining at Mindola Mine, Rokana Division of Nchanga Consolidated Copper Mines Limited is the deepest on the Zambian Copperbelt. Mining extends to 1150 metre depth so far and the present plans extend to 1500 metres, although reserves exist below this level. Mindola Mine is the major producer of copper/cobalt ore at Rokana Division and produces approximately 200,000 tonnes of copper/cobalt ore per month. A standard open stoping method is the only method used for mining with minor variations in positioning drilling drives and other development, figure 1. The standard main haulage interval is 75m but in flat dipping areas the full stope height is split into two or three panels. In 1970 severe mining problems were experienced when mining deeper than 850111 below surface. The main problems included: - Heavy support requirements in drilling drives near stope face. - Premature closure of blast holes necessitating pre-charging of the holes with explosives immediately after drilling and well before the day of blasting. - Severe bumping and spitting due to rock movements on drive surfaces and remotely within the rock mass under high stress. - Low mining efficiency due to dilution from the waste hangingwall. - These stress related factors also caused some premature detonations of precharged but unprimed blast holes which became a serious safety hazard. A number of alternatives have been considered to overcome these problems. A search for leas sensitive explosives to avoid the premature detonation problem has been partially successful, however, the need for a method of reducing stress levels at the mining face is still considered essential as the mine goes deeper. This paper describes experiments with Regional Support Pillars as a method of reducing stresses at the mining face.

Jan 1, 1981

Jan 1, 1920

FEB. 17-The past month found the average citizen backed off just a little more into his blind corner staring glassily at hydrogen bombs, unbalanced budgets, John L. Lewis, more inflation, a rising wave of strikes, the country's only active battleship on a mudbank, a famous scientist in gaol as a traitor, a favorite actress on a Roman holiday, and rising mountains of potatoes, butter and eggs begging for destruction. About the only bright spot has been industrial activity and employment, but even these are menaced by the coal shortage. Most industries have orders on hand or in prospect to warrant high operations for some time to come. The trend of the Reserve Board's production index is upward except as strikes may interfere. There has been heavy buying at the seasonal merchandise shows, particularly in furniture and house-hold goods. The demand for goods of this kind illustrates greater confidence in the Spring outlook than was generally felt a year ago. Further, the demand also reflects improved market positions due to curtailment of output and reduction of inventories in 1949 and sustained consumer buying power. It demonstrates the strong support that is given directly to many businesses, and indirectly to all, by the phenomenal construction activity that is now under way. The Commerce Department places the number of new dwelling units started in 1949 at the new all-time high of 1,019,000.

Jan 3, 1950

By C. W. Bildt

During many years of service in the iron and steel industry I have frequently found, as have also many other engineers, that the common devices used for feeding coal into gas-producers are not what they ought to be in order to secure the best economy. The hopper-and-cone so generally used is familiar to all, and a brief study of its action will surely satisfy everybody that this device has several serious faults. In the first place, the charging is intermittent, and depends entirely upon an attendant. When the hopper is frequently emptied, it may work fairly well, but even then it suddeinly discharges into the hot producers a large body of coal, which is often violently converted into gas that rushes into the furnace, and, as the damper for the combustion-air cannot be regulated every time the producer is charged, there will be an excess of gas, which goes up the chimney unburned. Between the chargings the quantity of gas generated decreases, and there will often be an excess of air in the furnace,

Jan 1, 1899

Seattle offered sunny, dry weather to about 2500 mining men who assembled September 10 to 14 for the 1961 American Mining Congress. The impact of snappy sessions on national mineral policy, state of the industry and foreign competition (to name only a few) was somewhat overshadowed by enthusiasm of conventioners for salmon fishing. This lordly fish, which mysteriously runs to its hatching place to spawn and die at this time of year, was not cooperating with the anglers in Puget Sound. However, this did not prevent consuming ample amounts of the deliciously prepared Quinault salmon at the "Potlatch" celebration.

Jan 10, 1961

By R. Hogg, D. W. Fuerstenau

Based on a simplified model for the motion of particulate materials in horizontal, rotating cylinders, approximate expressions have been derived relating the power consumption of a tumbling mill to its dimensions and speed of rotation and to the amount and nature of the charge. The basic assumptions underlying the model are that there is no slip between the charge and the mill shell, that the free surface of the charge remains essentially planar during rotation, and that there is no transfer of momentum from the material flowing down the free surface back to the mill shell. The relationships formulated from this model have been shown to be in excellent agreement with experimental results taken from the literature. While the requirements of the model are most clearly met at low speeds of rotation, the results appear to be valid even for speeds up to 70-80% of the critical speed. Poorer agreement between theory and experiment is found when the charge consists of relatively large particles (balls) and when the filling of the mill exceeds 50% of the available volume. Qualitative explanations of these deviations have been offered.

Jan 1, 1973

By Charles Catlett

THE rapid development of the Portland-cement industry implies that the country is being very carefully searched for material suitable for its manufacture. Such material can be found at a great many places ; but deposits thoroughly satisfactory in chemical composition, and at the same time meeting all the other requirements connected with the economic production and profitable marketing of the product, are exceedingly few, if I may judge from the investigations which I have had to make in a number of States. The raw mixture which by its clinking and grinding forms Portland cement contains approximately 75 per cent. of carbonate of lime. This is found in nature as limestone or marl. The natural rock commonly carries either more than the required percentage of carbonate of lime (in which case it has to be reduced by suitable admixture of clayey ingredients) or less-in which case purer lime carbonate has to be added. The controlling ingredient, therefore, is carbonate of lime, or limestone of the right composition. Among the most serious difficulties is that of finding limestones low enough in magnesia to meet the exacting requirements of certain specifications. All engineers recognize that there is a limit beyond which it is not safe to let the magnesia go; but within that limit there is considerable difference of opinion. Until that difference is finally settled, no one would be willing to invest the large sum of money necessary for a Portland-cement plant, if it were not certain that the usual requirements in this particular could be satisfied. The usual limit in well-established specifications is 5 per cent. of magnesium oxide in the finished cement, but many specifications limit the amount to 3 per cent. These figures

Jan 9, 1907

By C. T. Butler, W. W. Kay, R. D. Boddorff, R. L Ash

DRILLING and blasting in anthracite open-pit mines is a continuous problem to contractors and explosive engineers because of the diverse conditions caused by the nature of the geological formations, the extensive mining of the portions of coal beds near the surface, and the proximity of many strip pits to populated areas. Pennsylvania anthracite occurs in four separate long and narrow fields totaling only 480 sq miles. The coal measures are rock strata and coal beds that are considerably folded and faulted. The crests of the anticlines are eroded extensively. The beds outcrop on the mountain sides and dip under the valleys. At first only the upper portions of the syn-clines could be stripped. Now stripping to increasingly greater depths is economically possible, as is indicated by the fact that the proportion of freshly mined anthracite produced by strip mining has increased from 3.7 pct of the total tonnage in 1930 to 29.6 pct in 1950. Much of the rock overlying the deeper beds now being stripped is so extensively broken that considerable difficulty is experienced in drilling satisfactory blast holes and in using explosives in such manner as to insure a uniformly broken material easily removed by the excavating machinery. Such breaking of rock strata has occurred because the bed now being stripped has been mined extensively in former years by underground methods, and tops of gangways and chambers have subsequently failed. Draglines are used to uncover coal where the overburden can be moved with little or no re-handling. These machines range in size from those having a 2 cu yd capacity bucket on a 60-ft boom to those handling a 25 cu yd bucket on a 200-ft boom. Draglines are also used to strip to the bottom of the coal basins if the depth and the distance between the crops are not too great. For this type of operation blast holes are drilled full depth to the bed. These holes are commonly 30 to 90 ft deep; however, in exceptional cases, holes may be as shallow as 12 ft or as deep as 130 ft. Drilling is normally done for blasts of 12,000 to 60,000 cu yd of overburden, 30,000 cu yd being considered an average blast if vibration is not the controlling factor. Where the stripping of wide basins or the exposure of a moderately pitching vein makes the use of draglines impractical, dipper front shovels equipped with 4 to 6 cu yd buckets load into trucks. Overburden is removed in benches of 25 to 30 ft with blast holes drilled 4 or 5 ft deeper than the planned floor of the bench. For shovels under 5 cu yd bucket capacity the volume blasted varies from 8000 to 12,000 cu yd, whereas a volume of 30,000 to 50,000 cu yd of overburden is frequently blasted at one time for the larger shovels where vibration is not an important factor. During the past decade the churn drill, generally the Model 42-T Bucyrus-Erie blast hole drill equipped for drilling 9-in. diam holes, has become the most common blast hole drilling machine. Electricity powers half the churn drills in use and is preferred on the large strippings where electric shovels are operated and the working area is concentrated. On these operations the cost of additional electricity for the drills is less than the cost of fuel to operate diesel units because of the existing large demand load of the excavating equipment. Moreover, electric motors start more easily in cold weather and generally are less expensive to maintain. Diesel driven units are employed where a higher degree of mobility is required. The average drilling speed is 8 ft per hr, although in softer rocks a rate of 15 ft per hr is attained. Where rock is hard and strata is badly broken, drill speeds may be less than 2 ft per hr. Low drilling production results under these circumstances when loose material falling from the upper portion of the drill holes causes drill stems to be jammed. Rock formations vary so greatly in the region that a 9-in. diam churn drill bit may become dull after drilling only 2 ft or may drill satisfactorily for 56 ft; however, an average of 35 ft is usual in sandstone of medium hardness. Dull bits are hoisted to flat bed trucks by the sand line of the drill and are usually sharpened in the contractor's bit shop adjacent to the job. Care is generally taken to cover the thread end of the bit with a cap. To facilitate handling of bits around the drill, a heavy thread protector having an eye top is becoming more popular than the flat-top rubber or metal cap furnished with new bits. The 9-in. diam blast holes for a 25 to 30 ft bench are normally on 18x18 ft to 20x20 ft spacings, depending on the character of the overburden, although in broken ground 15x18 ft centers may be used to obtain better breakage and a more even bottom for the bench. The patterns of holes for shots

Jan 1, 1953

By R. D. Boddorff, R. L. Ash, C. T. Butler, W. W. Kay

DRILLING and blasting in anthracite open-pit mines is a continuous problem to contractors and explosive engineers because of the diverse conditions caused by the nature of the geological formations, the extensive mining of the portions of coal beds near the surface, and the proximity of many strip pits to populated areas. Pennsylvania anthracite occurs in four separate long and narrow fields totaling only 480 sq miles. The coal measures are rock strata and coal beds that are considerably folded and faulted. The crests of the anticlines are eroded extensively. The beds outcrop on the mountain sides and dip under the valleys. At first only the upper portions of the syn-clines could be stripped. Now stripping to increasingly greater depths is economically possible, as is indicated by the fact that the proportion of freshly mined anthracite produced by strip mining has increased from 3.7 pct of the total tonnage in 1930 to 29.6 pct in 1950. Much of the rock overlying the deeper beds now being stripped is so extensively broken that considerable difficulty is experienced in drilling satisfactory blast holes and in using explosives in such manner as to insure a uniformly broken material easily removed by the excavating machinery. Such breaking of rock strata has occurred because the bed now being stripped has been mined extensively in former years by underground methods, and tops of gangways and chambers have subsequently failed. Draglines are used to uncover coal where the overburden can be moved with little or no re-handling. These machines range in size from those having a 2 cu yd capacity bucket on a 60-ft boom to those handling a 25 cu yd bucket on a 200-ft boom. Draglines are also used to strip to the bottom of the coal basins if the depth and the distance between the crops are not too great. For this type of operation blast holes are drilled full depth to the bed. These holes are commonly 30 to 90 ft deep; however, in exceptional cases, holes may be as shallow as 12 ft or as deep as 130 ft. Drilling is normally done for blasts of 12,000 to 60,000 cu yd of overburden, 30,000 cu yd being considered an average blast if vibration is not the controlling factor. Where the stripping of wide basins or the exposure of a moderately pitching vein makes the use of draglines impractical, dipper front shovels equipped with 4 to 6 cu yd buckets load into trucks. Overburden is removed in benches of 25 to 30 ft with blast holes drilled 4 or 5 ft deeper than the planned floor of the bench. For shovels under 5 cu yd bucket capacity the volume blasted varies from 8000 to 12,000 cu yd, whereas a volume of 30,000 to 50,000 cu yd of overburden is frequently blasted at one time for the larger shovels where vibration is not an important factor. During the past decade the churn drill, generally the Model 42-T Bucyrus-Erie blast hole drill equipped for drilling 9-in. diam holes, has become the most common blast hole drilling machine. Electricity powers half the churn drills in use and is preferred on the large strippings where electric shovels are operated and the working area is concentrated. On these operations the cost of additional electricity for the drills is less than the cost of fuel to operate diesel units because of the existing large demand load of the excavating equipment. Moreover, electric motors start more easily in cold weather and generally are less expensive to maintain. Diesel driven units are employed where a higher degree of mobility is required. The average drilling speed is 8 ft per hr, although in softer rocks a rate of 15 ft per hr is attained. Where rock is hard and strata is badly broken, drill speeds may be less than 2 ft per hr. Low drilling production results under these circumstances when loose material falling from the upper portion of the drill holes causes drill stems to be jammed. Rock formations vary so greatly in the region that a 9-in. diam churn drill bit may become dull after drilling only 2 ft or may drill satisfactorily for 56 ft; however, an average of 35 ft is usual in sandstone of medium hardness. Dull bits are hoisted to flat bed trucks by the sand line of the drill and are usually sharpened in the contractor's bit shop adjacent to the job. Care is generally taken to cover the thread end of the bit with a cap. To facilitate handling of bits around the drill, a heavy thread protector having an eye top is becoming more popular than the flat-top rubber or metal cap furnished with new bits. The 9-in. diam blast holes for a 25 to 30 ft bench are normally on 18x18 ft to 20x20 ft spacings, depending on the character of the overburden, although in broken ground 15x18 ft centers may be used to obtain better breakage and a more even bottom for the bench. The patterns of holes for shots

Jan 1, 1953

By George A. Lamb

AMONG the main interesting developments in the coal market have been the changes that have taken place between the consumer groups. Important signs of these changes began to appear many years ago, but in a modest way, and were apparent only to the few fuel experts making broad statistical determinations. It is doubtful, however, that any of these experts appreciated the significance of their early findings, and perhaps none had the imagination to consider how extensive these changes might be eventually with respect to solid fuels sales and distribution. (Reference here will be principally to bituminous coal.) Railroad Fuel Major changes in coal use did become pronounced after World War II, and it did not take an expert to see what was taking place and how serious the impact was likely to be. First, was the case of the steam and diesel locomotives. The railroads had been considered the best coal customers; they were steady and large purchasers and usually paid a better price than most others. Railroad fuel provided the basic mine realization and it often was the source for operating cash during general market slumps. It was the outlet for 20 pct of the bituminous coal production, as much as 110 million tons in 1946.

Jan 2, 1957

By E. Eichen, G. S. Ansell. L. R. Sefton

A Technique for the Preparation of Thin Films of Two-Phase Alloys Suitable for Use in Transmission Electron Microscopy In order to obtain foil sufficiently thin to permit transmission electron microscopy of two-phase alloys, particularly alloys in which the second phase is present as a very finely dispersed second phase, a technique has been developed to permit the thinning of these materials without either the large degree of pitting present in the electrochemical or chemical thinning process or the slicing of the second phase particles accompanying the mi-crotoming process. The metal or alloy to be thinned is first ground to initial sheet thickness of approximately 0.002 in. by hand grinding on 4/0 emery paper. This starting sheet of material is then reduced in cross section by an air-abrasion technique using an S. S. White dental abrasive unit. This unit consists of a supply of compressed CO, which provides a stream of high velocity gas impinging on the metal surface. Incorporated in the machine is a hopper-type of device in which fine abrasive particles of alumina are introduced into this high velocity gas stream. The abrasive particles are irregular in shape, approximately 30 across. If any particles are introduced into the sample during thinning, they should be readily observable. Impingement of this gas abrasive mixture on the metal surface causes rapid removal of the metal in a rather uniform manner. The rates of metal removal may be adjusted by both regulating the gas pressure and amount of abrasive material introduced into the gas stream. By moving the gas stream abrasive mixture slowly about the specimen or sheet surface, a large area of the sheet may be uniformly reduced to a thickness which is then suitable for use in transmission electron microscopy. Attendant with this metal removal is a result in cold working of the metal surface due to the impingement of the abrasive particles. The resultant foils, therefore, if made from materials which are desirable to view in the annealed condition, have to be subsequently heat treated. If the alloy from which these foils have been made has been initially heavily worked or deformed during manufacture, then no subsequent heat treatment is, necessary as in the case of the SAP-type alloys. Following this initial abrasive thinning technique, the material is then given a final electropolish which is just sufficient to remove any oxide which has formed on the metal surface during the abrasion technique. Care has to be exercised in this technique to make sure that none of the attendant problems associated with the chemical or electrochemical removal process are encountered. An electrolyte solution which has been found suitable for aluminum-aluminum oxide SAP materials is one containing 78 ml of perchloric acid, 120 ml of distilled water, 700 ml of ethanol, and 100 ml of butylcellosolve. The current density used is 1 amp per sq cm and a polishing time of 3 sec on each side of the foil is used. Extreme care must be used in choosing the current density and time to ensure that just the oxide film on the specimen is removed. Times or current density which are greater than this will lead to perforation of the film due to the removal of the A1,0, particles or a complete loss of the film due to complete solution of the matrix. Once the oxide film is removed the specimens must be kept in alcohol until placed in the microscope to prevent any further oxidation. Fig. 1 shows -an electron micrograph at X28,000 of a thin foil of an aluminum-aluminum oxide SAP-type alloy prepared using this technique. The alloy consists of a matrix of commercial purity aluminum containing a very finely dispersed second phase of aluminum oxide flakes. In the electron micrograph, the dark patches are the aluminum oxide particles. The lighter portions of the micrograph are the aluminum matrix. Within the aluminum matrix, the dislocation structure of the alloy is clearly visible. This structure consists of intersecting twin boundaries and single dislocations. No abrasive particles were observed in the samples. In addition, thin films of commercial purity aluminum were prepared using this method and observed in the electron microscope. Here also, there was no evidence of abrasive particles introduced in the samples. The technique presented provides a satisfactory method for the production of thin films of aluminum-aluminum oxide SAP-type alloys for use in transmission electron microscopy where none of the usual thinning techniques appears to be satisfactory.

Jan 1, 1962

By R. W. Kobler, D. A. Dahlstrom

Since the development of the pelletizing process in the fifties for relatively high purity pellets from low grade taconites, there have been several distinctive changes in filter construction for the dewatering step preceding balling. In the original large pilot plant run by Reserve Mining Co. in Babbitt, MN, the disk type filter employing agitation (Agidisc filter) was selected as the most economical. Size was limited to 2.1 m (6 ft, 9 in.) in diameter. The second generation occurred in the sixties with a jump to 2.70 m (8 ft, 10 in.) in diameter to reduce capital costs per annual ton of pellet. In the early seventies, the third generation was the steam drying disk filter which became necessary to achieve balling moistures with specific surface areas of 2200 cm2/g to as high as 3800 cm2/g caused by finer grinding to obtain higher purities. Finally, the fourth generation has recently been developed to reduce maintenance costs and further improve hydraulics to ensure minimum moisture contents.

Jan 1, 1980

By Jan M. Mutmansky

The primary purpose of this presentation is to analyze the strategies available to an operator using either stripping or stripping and subsequent punch mining on a given coal property. The initial concern is the formulation of a mathematical model, which allows an operator to determine and utilize the particular highwall height, which will maximize : (1) Total profit or (2) Profit per unit of operating time. The analysis centers on the relative costs and recoveries involved in a typical coal seam amenable to stripping, augering, and punch mining. The model defines the point to which the high-recovery stripping operation with increasing overburden removal and reclamation costs should proceed before the low-recovery augering and punch mining methods are employed so that the desired objective is achieved. Examples are presented, which exhibit the use of the model on typical operations. Present mining methods as practiced in the Eastern United States are examined in the light of the results. Recommendations for improving present strategies are made and the resulting economic ramifications are analyzed. Particular attention is given to the stripping ratios presently used and recommendations for improving present mining practice are presented. Implications of these recommendations to the design of strip mining equipment are discussed.

Jan 1, 1977

By C. A. Wright

Since the adoption by the U. S. Bureau of Standards several years ago of specifications for standard 100- and 200-mesh sieves, frequent requests have been received that this Bureau test and certify sieves of other sizes than these. With a view to the adoption of a series of standard testing sieves which might be of use to all industries making fineness tests, this Bureau for two years has been studying the question of such a standard screen scale. Various scales that have been proposed were considered, and information was sought of representative firms in the various industries interested as to their requirements. Manufacturers of sieves have also been consulted as to the desirability of different screen scales and the practicability of their manufacture. As a result of this study of the question, a conference was called at the Bureau of Standards, Apr. 20, 1916, of representatives of various committees of the American Society for Testing Materials, American Society of Civil Engineers, American Institute of Mining Engineers, American Foundrymen's Association, Mining and Metallurgical Society of America, American Water Works Association, American Institute of Metals and the American Spice Trade Association; also representatives of the Committee of Revision of the U. S. Pharmacopæia, the U. S. Geological Survey, the U. S. Bureau of Mines, the U. S. Office of Public Roads and Rural Engineering, the U. S. Office of Grain Standardization and the U. S. Bureau of Standards; also representatives of a number of private firms engaged in industries in which sieves are used, such as the glass, the drug milling, the abrasive, the asphalt, the mining, the spice, the chemical, and the graphite industries; also representatives of the firms in this country manufacturing wire cloth and sieves. This Conference, after considering the various screen scales either proposed or now in use, adopted as a Standard Screen Scale that given in Table 1, and recommends that it be adopted generally by scientific,

Jan 1, 1918

By L. M. Higgins

Dust or fume control systems are devices for capturing contaminants at their source and preventing their discharge to atmosphere. The Primary Components Of Any Dust Control System Include: An enclosure around any potential dust source such as conveyor belt transfer, crusher, screening machine, bin loading and loadout. Ductwork including hood takeoffs (transitions) to convey the collected dust laden air away from the source of dust generation to a convenient location. A dust collector for separation of particulate matter from the air stream prior to its discharge to the atmosphere. A prime mover generally a fan, to draw air into an enclosure and to overcome resistance to flow in the ductwork, dust collector and stack.

Jan 1, 1978

By Dewitt T. Ring

Lack of reliable detailed production figures for earlier years, together with the loose nomenclature in reference to producing horizons and the application of the term "field" without any definite meaning or restriction, has made it impossible to gather statistical data suitable for the Institute's form. In common with all other producing areas in the United States, Ohio has felt severely the economic ills of the entire industry during the past year. With overproduction, not only of crude but also of refined products, going on throughout the country, the price structure as a direct consequence has weakened on Ohio oils. Valuable crude is being sold at a big loss today because producers arc willing to, and do, sell more than the market can absorb. The axe hangs heavy over the heads of Ohio producers, and will until something constructive is done to keep supply in proportion to demand. This not only applies to Ohio but to the entire industry. Production of Pennsylvania grade in Ohio was under 50 per cent proration, which has been in effect since Oct. 1, 1937. Three price cuts since February have lowered the posted price from $1.70 to $1.18, a 30 per cent reduction; other grades were less drastically reduced. Pipeline storage facilities were limited; many producers were faced with the problem of providing their own storage or the risk of ruining their wells. If they wanted to pull and abandon wells, there was no market for junk equipment. Many employees have been cut to half time and in a number of instances their services entirely dispensed with. Summary of Production and Drilling Both oil and gas production in the state during 1938 showed a definite decline over the previous year. (A table showing production by years from 1876 through 1937 was published in Vol. 127 of the Transactions.) The total production of crude oil in the state for 1938 was 3,357,914 bbl., as compared with 3,654,000 bbl. in 1937, a decrease of 7.1 per cent. At

Jan 1, 1939

By Dewitt T. Ring

Lack of reliable detailed production figures for earlier years, together with the loose nomenclature in reference to producing horizons and the application of the term "field" without any definite meaning or restriction, has made it impossible to gather statistical data suitable for the Institute's form. In common with all other producing areas in the United States, Ohio has felt severely the economic ills of the entire industry during the past year. With overproduction, not only of crude but also of refined products, going on throughout the country, the price structure as a direct consequence has weakened on Ohio oils. Valuable crude is being sold at a big loss today because producers arc willing to, and do, sell more than the market can absorb. The axe hangs heavy over the heads of Ohio producers, and will until something constructive is done to keep supply in proportion to demand. This not only applies to Ohio but to the entire industry. Production of Pennsylvania grade in Ohio was under 50 per cent proration, which has been in effect since Oct. 1, 1937. Three price cuts since February have lowered the posted price from $1.70 to $1.18, a 30 per cent reduction; other grades were less drastically reduced. Pipeline storage facilities were limited; many producers were faced with the problem of providing their own storage or the risk of ruining their wells. If they wanted to pull and abandon wells, there was no market for junk equipment. Many employees have been cut to half time and in a number of instances their services entirely dispensed with. Summary of Production and Drilling Both oil and gas production in the state during 1938 showed a definite decline over the previous year. (A table showing production by years from 1876 through 1937 was published in Vol. 127 of the Transactions.) The total production of crude oil in the state for 1938 was 3,357,914 bbl., as compared with 3,654,000 bbl. in 1937, a decrease of 7.1 per cent. At

Jan 1, 1939

By Gareth Thomas

The analysis of Kikuchi pattersns of exct ovientalions from single cryslals and paired Kikuchi lines from single and overlapping crystals is shown to be useful and quanlitalve and is applied to Phase transfovnzcitions including ordering, spinodals, mavten-silic, and nuclealion and growth pyocesses. 112 pinciple, the analysis of exacl orientations enables the crystal system and the Bravais lattice of a crystal to he determined. The advantages of the davk-field imaging technigure for detecting vevy small precipitates are also described. ALTHOUGH Kikuchi electron-diffraction patterns were first observed nearly 40 years ago,' little systematic application seems to have been made of them, until fairly recently during electron microscopy, when their usefulness in contrast experimen and for determining exact orientations8'9 has been pointed out. With the availability of gonio-metric specimen tilting stages it has now become possible to make much wider use of diffraction patterns, particularly the Kikuchi pattern, which is the main subject of this paper. The treatment presented here is not exhaustive but it is hoped that it will stimulate more use of Kikuchi patterns during electron-microscopy investigations. The Kikuchi pattern is formed as a result of Bragg diffraction of the inelastically scattered electrons produced during the interaction of the beam and thick specimens, The important feature of these patterns is that they give an accurate representation of the symmetry of the crystal being investigated, so that it is possible to identify crystal systems and even the Bravais lattice. This means that new structures, e.g., formed in phase transformations, may be identified during normal electron microscopy, so that Kikuchi-pattern analyses considerably extend the uses of the electron microscope. Recent work has also shown that dark-field images are more informative than bright-field images, particularly, for observing small precipitates. The second part of this paper discusses some applications and advantages of dark-field imaging in studies of two-phase systems. 1) DIFFRACTION PATTERNS 1.1) Spot Patterns. Electron-diffraction spot patterns have their limitations because of the importance of the form factor on the intensities and shape of the reciprocal lattice points. Because of the extension of these points into relrods, reflections are possible over a large angular range (+5 deg) and the patterns from thin regions can be complicated because second-layer relrods intersect the reflecting sphere. Spot patterns can thus give only an approximate idea of the crystallography unless the foil is tilted into exact orientation. In this case the spot pattern is symmetrical, with equal numbers of spots on the positive and negative zone directions about the origin. Such cases are necessary for structural analyses and have been used recently to determine the crystal structure of the ordered Ta64C phase." Exact orientation means that the plane of the reciprocal lattice lies exactly normal to the incident beam as shown in Fig. 1(b). It should be noted that in exact orientations the angle of reflection is less than the exact Bragg angle 9 so that the reciprocal lattice points lie to the outside of the sphere, Fig. 1(b). This deviation is denoted by the parameter s and in the usual convention4 s is negative for exact orientations and, of course, zero at the exact reflecting position shown in Fig. l(a). In order to avoid secondary reflections from thickness relrods it is advantageous to work in thicker regions of foils. Diffraction from thick regions may also produce Kikuchi patterns and as dis-

Jan 1, 1965