Search Documents

By Robin O. Williams

Robin 0. Williams (Oak Ridge National Laboratory)— The authors have questioned the degree to which the coherency strains between the iron-rich and chromium-rich phases are isotropic as proposed in Ref. 5 on the basis of the difference between the elastic properties of the two phases. The relative magnitude of the stresses is determined by the moduli as shown by Eqs. [2], [3], and [4] of Ref. 34. However, the moduli of the two phases have no direct bearing on the uniformity of either the stress or strain within either phase. The idea that the strains are isotropic within each phase (but normally of different magnitude and always of different sign) is based entirely upon the experimental observation that X-ray line broadening has not been detected even when the particles become rather large. It has not proven possible to grow the particles sufficiently large that they lose coherency. Based upon this lack of line broadening one can estimate an upper limit for the nonuniformity of the strains within each phase as follows. It is considered possible to detect line broadening if it is as great as 10 pct of the separation of the K, doublet for the (211) line using chromium radiation. The doublet separation would correspond to a total strain of 0.0017 such that the total variation of lattice parameter relative to the average lattice is now k0.05x0.0017 or something less than ± * For the present case the strain in each phase is roughly 0.002 such that the variation of strain within a phase will not exceed 5 pct. It is stated that the expression derived for strengthening for the hydrostatic straining as observed in this system would substantially overestimate the magnitude due to dislocation flexure. This is contrary to the conclusion reached in the original paper34 for the present range of particle sizes. What is the lowest temperature at which a has been observed to form in this alloy? M. J. Marcinkowski, R. M. Fisher, and A. Szirmae (nutlzors' reply)— -Williams' arguments based on X-ray findings for a chromium-rich precipitate and an iron-rich matrix strained to a common lattice parameter are certainly convincing. This being the case, there are no shear components of strain associated with the precipitate-matrix aggregate to interact with the shear components of the dislocation stress fields, contrary to the opinion expressed by the present authors. On the other hand, the present authors, in spite of this error, did not expect the shear interactions to be significant. The chief objection to Williams' model in the present case is that the various segments of the dislocation line are assumed to pass from one potential valley to the next independently of neighboring segments. This is only true for a highly flexible dislocation line, i.e., one whose radius of curvature is something less than the center to center distance between precipitate particles which amounts to about 90A in the present alloy. In order to maintain this curvature, an externally applied shear stress of at least 230,000 lb per sq in. would be required or about four times the observed stress. It is therefore concluded that the dislocation lines move rather rigidly through the lattice. This being the case, the forces on the dislocation resulting from the hydrostatic interaction between the stress fields of the edge-dislocation components and the precipitate particles should average out to zero; that is particles above the below the slip plane produce forces on the dislocation of opposite sign and therefore will cancel when averaged over the entire length of the dislocation. On the other hand, since the dislocation is not perfectly rigid, Williams' model may lead to some strengthening, but far less than that predicted. A second and equally serious objective to using Williams' strengthening model for the present alloys is that profuse wavy slip due to the motion of screw dislocations played a predominant role not only in the unaged alloys but in the fully aged ones as well. Since the screw dislocation has associated with it only shear components of stress the hydrostatic strengthening model no longer applies. In view of these arguments the present authors must reject Williams' model of strengthening as being pertinent to the present alloy system. The present authors have made no detailed study of the lowest temperature at which a forms in the quenched ferritic alloys. None was ever observed n the alloys aged at 500°C so that forma-tion must occur at temperatures higher than this and was therefore not a factor in the present study.

Jan 1, 1965

By Renato G. Bautista, Robert A. Hard

A comparative study has been made of the ex-tractability of several of the transitim metals from thiocyanate sohtions using methyl isobutyl ketone as the organic solvent. Extractions were made of scandium (III), chromium (III), manganese (II), iron (III), and cobalt (II), of which only the scandium , iron, and cobalt were readily extracted. All extractions were made at pH 2 and at 25.5 °C. A series of extraction experiments was made on scandium, iron, and cobalt to determine the effect of thiocyanate cmcentration added as the ammonium and also as the calcium salt. Also determined was the effect of metal ion concentratim and ionic strength on the distribution ratio. Analyses of the organic extracts indicated the scandium and iron were extracted principally in the uncharged trithiocyanate form, while the extractable form of the cobalt contained the cobaltotetrathiocyanate anion. THE chemical separation of metal complexes in solution by solvent extraction has in recent years been developed for large scale separation as well as bench scale work in the laboratory. It has also found increased application in analytical chemistry. Its extension to extractive metallurgy as a unit operation is best illustrated in the recovery of uranium and vanadium from their leached liquor.5-8 The extractability of some thiocyanate systems have been extensively investigated. The rate earths have been separated from one another using butanol as a olvent. Scandium was effectively extracted in ethyl ether using ammonium thiocyanate as the com-plexing agent.'' Similarly, the separation of hafnium from zirconium has been reported using ether""' or hexone13 as the organic solvent. The extractability of various metal thiocyanates in ethyl ether is given by 0ck.l Sharp and Wilkinson15 prepared nickel-free cobalt slats by thiocyanate extraction. The mechanism of extraction of titanium (IV) thiocyanate with methyl isobutyl ketone was determined by elafosse.''" The characterization of cobalt (TI) thiocyanate complex using methyl isobutyl ketone as the solvent at near neutral aqueous solution and the spectrometric studies of the ex-tractable cobalt complex has been made by Hard." It is noteworthy to mention at this point that the fundamental characteristic of ketone (oxonium) solvent extraction is that the extractable species are uncharged ion pairs solvated by the ketone molecules, but probably still partially hydrated.

Jan 1, 1963

The library of the above-named Societies is open from 9 A. M. to 10 P. M. except on holidays. It contains about 70,000 volumes and 90,000 pamphlets, including sets of technical periodicals and publications of scientific and technical societies. Members of the Institute, with few exceptions, are forced to spend a portion of their time in localities isolated from sources of information. To these the Library, through its Library Service Bureau, can render valuable service through correspondence; letters requesting information will receive especial attention. The Library is prepared to furnish references and photographic copies of articles on mining and metallurgical subjects; to determine the existence of mining maps, and to furnish general information on the geology and mineral resources of all countries. All communications should be made as definite as possible so that the information received may be what is desired and not include collateral matter which may not be of interest. The time spent in searching for such collateral matter will be saved, and the information will be sent more promptly and in more usable shape.

Jan 12, 1918

By A. L. Baxley

An Untapped Energy Resource As much as 20 billion cubic feet of natural gas per day are flared from remote oil fields for lack of a commercially viable means of capturing, transporting, and marketing such gas. The magnitude of these gas flares can be put into perspective from an early satellite photograph (Fig. 1) which shows lights from the major cities of Russia and Eastern Europe dwarfed by the natural gas being flared in the Persian Gulf. Together, these wasted resources contain the energy equivalent of about one-half of the gasoline consumption in the United States today (Fig. 2). Additional trillions of cubic feet of natural gas are "shut-in" because of no economically viable means of commercial recovery. Methanol and liquified natural gas (LNG) are the only two practical fuel products which can be produced economically from these gas supplies. Many of these gas supplies are less than 500 million cubic feet of gas per day, making an LNG facility uneconomic. In contrast, barge-mounted methanol plants can economically convert billions of cubic feet of gas per day into safe, clean-burning methanol. The methanol approach offers the only economical route to transform vast, known reserves of natural gas into a highly versatile primary liquid fuel. Methanol Barges: An Innovative Solution The barges will be towed to suitable offshore and upriver locations such as Alaska, South America, Africa, Southeast Asia, Australia, New Zealand, and the South Pacific Islands, as well as fields in the Persian Gulf and Mediterranean Sea. At the offshore production site, a barge will be anchored by a single point mooring buoy that will also serve as an entry point for natural gas feedstock and an offloading point for methanol (Fig. 3). At some sites the barge would be beached. Each barge will produce methanol and store it in internal tanks with a capacity of 18 million gallons. The methanol will be offloaded into conventional tankers and safely transported directly to market. Unlike LNG, methanol requires neither specially built carriers nor specially built receiving terminals. Once a particular gas field has been exhausted, the barge will be towed to another location to continue production. Each barge will measure 320 by 500 ft, approximately the size of four football fields, and will have the capacity to produce 1 million gallons or 2800 metric tons of methanol per day, from approximately 100 million cubic feet of natural gas per day (Fig. 4). The barges will use the highly successful "low- pressure" design developed by the Lurgi Company of Germany, a process proven in land-based methanol plants throughout the world during the last ten years. The decision to use Lurgi technology for "sea-trans- portable" methanol plants was based on the higher efficiency and greater operability of the technology compared to other commercially proven processes. The conversion plant will be designed to accept a wide variety of feed gas compositions, and will produce chemical-grade methanol for the broadest market base (Fig. 5). To minimize costs and construction time, the barge-mounted plants will be built in the high technology environment of a domestic or foreign shipyard. Selection of the construction site for each barge will be dictated by the location of the production site and by the relative construction costs. A number of shipyards have the capacity to build several barges per year. The detailed marine engineering to integrate the design of the processing plant with the floating platform can be performed by numerous major engineering companies around the world. Production Economics The barge-mounted plant concept not only assures large volumes of methanol, but it also keeps the overall production cost low by minimizing construction cost and providing access to low cost natural gas feedstock with no alternative or a negative value. Together, these advantages make the barge-mounted methanol plants economical today. The cost structure of a new barge-mounted methanol plant differs from that of existing methanol producers around the world (Fig. 6). For example, if a U.S. Gulf Coast producer is paying $4.70/MMBtu in 1985 for natural gas, the barge plant could afford to pay about $1.6O/MMBtu for gas and be able to deliver methanol to the Gulf Coast at the same price. At some future date such as 1990, a gas cost of $6.70/MMBtu for a domestic producer would have cost parity with about $3.60/MMBtu gas cost for the barge plant. In many foreign markets, feedstocks other than natural gas are used for methanol production (Fig. 7). For example, most of Japan's capacity is based on LNG while Western Europe uses residual oil or naptha. Because these feedstocks are substantially more ex- pensive than natural gas used by U.S. producers, the barge plants will compete even more favorably in these foreign markets. As crude oil prices rise, the value of methanol in each of these markets will increase. However, the hierarchy of methanol values in these markets should remain unchanged. Furthermore, the cost advantage for using methanol in these markets will improve as world energy costs increase since the value of remote gas should not escalate significantly.

Jan 1, 1982

By D. Turnbull, J. C. Fisher

ACCORDING to the "reaction-path" modell,2 of martensite nucleation, the shear angle of the embryonic martensite plate must be treated as a variable, and included in any calculation of nucleus critical size. Also, as can be deduced from this model, the interfacial free energy between austenite and martensite does not reach its final value until the shear is completed. It is zero for zero shear angle. However, in order to account for the kinetics of the martensite transformation, some sort of interfacial energy barrier appears to be necessary even with the reaction-path model, for otherwise the volume and the energy of formation of the critical size nucleus both collapse to zero.3 Cohen independently suggested that surface energy could be incorporated into the reaction-path model, with the overall free energy of a martensite embryo being a function of its volume and shear angle.' It is possible to estimate the energy associated with the formation of a critical-size martensite nucleus starting with the reaction-path model and including a surface free-energy barrier. As the dependence of interfacial free energy upon shear angle is unknown, a simple type of dependence will be assumed, with the belief that the true dependence would not lead to appreciably different results. Consider the work required to form a lenticular martensite plate with radius r, thickness t, and shear angle 8. There are three contributions; one being the interfacial free energy, one being the free energy change in the martensite plate, and one being the free energy increase in the surrounding austenite. The interfacial free energy u is assumed to depend upon the shear angle 0 according to the relationship s=s0(?/?0)n [1] where 8, is the equilibrium shear angle and n is an exponent that may lie in the range 0 n 2. The work required to form the interfaces of a martensite plate then is W. = 2pr² s0(?/?0)n [2] The free energy change per unit volume of martensite is composed of two parts, one the ordinary volume free energy ?f1. which is negative, and the other the elastic strain energy G?m²/2, where G is the shear modulus and 7, the shear strain relative to the martensite structure. This expression for the strain energy is valid only when the shear strain ym, is sufficiently small that the martensite is within its linear elastic range. There is no doubt that ym, lies beyond the linear elastic range for embryos that are considerably subcritical. However, for critical nuclei it will be shown that ym, is 1.5 pct or less, within the linear elastic range of martensite. For embryos of nearly critical size, then, the strain energy of the martensite is correctly given by G?m²/2. The shear strain in the martensite is ym, = 8, — 8, and the work required to form the strained martensite is Wm --= (pr²t/2) [?fv + G(?O - ?)²/2] [3] The free energy change in the austenite is entirely that due to elastic distortion. The elastic strain is not uniformly distributed in the austenite, being large near the martensite plate and small elsewhere. Approximately, however, the energy corresponds to a uniform shear strain ya= (?t/2)/r [4] throughout the volume 4pr³/3 surrounding the plate. The work required to strain the surrounding austenite then is Wa = (4pr³/3) (G?a²/2) = (G?²/6) prt² [51 For simplicity, the same shear modulus G is assumed for each structure. The total free energy for forming a plate then is W = W3 + Wm + Wa. = 2pr² s0 (?/p?0)n + (pr²t/2) [?fr+G(?0-?)²/2] + (G?²6) prt2 [6] This expression is correct for nuclei and for embryos of nearly critical size, where, as will be shown, the strain energy in the martensite is correctly given by the expression G (? — ?)². Having W as a function of r, t, and 8, as in Eq. 6, there is a saddle-point where W has a stationary value, W subsequently decreasing indefinitely as the nucleus volume increases along the reaction path. The stationary value of W is the energy of the critical nucleus. The critical nucleus has radius, thickness, and shear angle such that ?W/?r - awlat: = ?W/?p? = 0. Performing these differentiations and calculating the critical nucleus energy, W* = [8192p(G?/6)²;s/27 ?fv4] [7] where a= (?/?0)3n+1[l +G(8"-8)'/2af.]' [7a] and where 8 is to be determined from the equation (1 + 3n/4) + G8(6O - (9)/[Af. +G(6>o-6>)72] = 0 [8] For ?f, near —200 cal per mol or —10" ergs per cc, and 8, near 1/6, as for iron-base alloys, Eq. 8 gives ?0 - ? ~ - (4 + 3n) ?f1./4G0O [9] as the difference between the equilibrium shear angle and the actual shear angle for a critical nu-

Jan 1, 1954

By P. E. Landolt

BEFORE World War I, and even prior to World War II, lithium was considered among the rare elements. Mining was limited to exploitation of a few well selected sources of rich minerals recoverable by hand cobbing methods. Within the past five years the situation has changed radically. Many new sources have been explored and developed, principally in Canada, North Carolina, and Southern Rhodesia. The prime raw material for lithium recovery is spodumene. In Southern Rhodesia, however, both petalite, a modified spodumene, and lepidolite, a lithium mica, are being mined in quantity.

Jan 4, 1957

By P. H. G. Durville

ANY metal which contains even a small percentage of aluminum possesses certain peculiarities of appearance and properties which are exhibited both when the metal is melted and after it solidifies. Pure aluminum, or an alloy containing a small proportion of aluminum, can be melted without flux-except for a layer of charcoal-because a film of aluminum oxide and metal forms at the surface of melted aluminum. Although very thin, this film is air-proof, and it prevents the metal underneath from oxidizing. This oxidized film does not move easily on account of its toughness and high surface tension. One very important point in connection with this process of still casting has not been strongly enough stressed, namely, that the same kind of surface film with the same peculiarities forms over the surface of all melted alloys that contain even a small proportion of aluminum. Experienced foundrymen know how desirable it is to cast aluminum under its "skin" or under the surface of the film which tends to remain still. In the case of red copper, when in fusion, the surface shows pure copper only. This is due to the fact that liquid copper constantly absorbs the copper oxide which forms on the surface. By closely examining melting copper the oxide can be seen dissolving in the bath, and going into solution just as pulverized sugar dissolves in water. When copper is cast in the open, either in wire bars or cakes, the surface of metal exposed to the air is covered by a film of black, oxide that cannot be absorbed by the metal.

Jan 1, 1927

By M. E. Straumanis, S. M. Riad

The lattice parameter of 99.999 pct pure Ag rtlas redetevnzined and found to be az5 = 4.08626 5 0.000041 with the vefnzctiotz correction included); the expatzsion coejjicient between 10° and 65°C was 18.73 X10-6°C-1. The lattice paratneter increased upon solution indium in silver in good agrement with other authors. The solid-solubility limit around room temperature was at 20.4 wt pct of in, which suggests that the high-temperature solubility (at about 689°C) determined by other authors is too low. The expansion coejficient of si1ver increases with the itzcrease of indium content between 10° and 65° C from, 18.73 (In = 0) to 20.9 x 10-6°C-1 (In = 20.4 pct), being only very slightly influenced by small amounts of indium. The expansion coefficents of all solid solutions increarsed strongly with temperature, reaching values > 27 x 10- 6 800°C. ACCORDING to the Ag-In diagram,' the solubility of indium in silver (the a phase) extends to about 18 pct by weight at room temperature. However, there has been only one investigation of the solubility limit by X-ray methods—that of Weibke and Eggers.2 Hume-Rothery, Lewin, and Reynolds measured only the lattice parameters of Ag-In solid solutions3 as did Owen and Roberts4 and Adler and Wagner.' The thermal expansivity of four solid solutions was determined by Owen and Roberts4 in a temperature range between 25" and 300°C. In view of the limited amount of work on Ag-In solid solutions, it seemed appropriate to redeter-mine the lattice parameters and the room-temperature solid-solubility limit, to find the exact expansion coefficients of the solid solutions at about room temperature (between 10° and 60°C) and the expansivity up to 800°C, and finally to derive the thermal-expansion coefficients for any alloy within the solid-solubility region. THE ALLOYS AND THE DETERMINATION OF LATTICE CONSTANTS The metals used were 99.9991 pet pure, supplied by the ASARCO company. Both silver and indium were weighed accurately on an analytical balance in

Jan 1, 1965

By T. D. Guldem, J. L. Kaae

ALLOYS with nominal composition of 45-Fe 35-Ni 20-Cr, ASTM-B-163, known under the commercial names of Incoloy 800 and Sanicro 31 (Alloy 800), are often employed at elevated temperatures for extended periods. Therefore, knowledge of the aging behavior of these alloys is of considerable importance. Significant decreases in ductility and increases in yield strength have been observed in the 45-Fe 35-Ni 20-Cr alloys containing about 0.4 pct Ti and 0.4 pct A1 after long-term aging at 540" to 700"~."~ However, no direct evidence has been presented for precipitation phenomena that might result in such changes. Strengthening effects have been attributed to the effects of local or-dering.3 Since y' precipitation (Ni3A1, Ti) is known to occur in similar alloys which contain more titanium and aluminum,4-7 it was decided to explore the possibility that y' might precipitate in these alloys and might be responsible for the changes in mechanical properties on aging. This note reports some observations of two distict types of matrix precipitates made by means of transmission electron microscopy, in a 45-Fe 35-Ni 20-Cr alloy containing 0.31 pct Ti and 0.4 pct Al. The steel used in this investigation was obtained from the Sand-vik Steel Works; it is designated Sanicro-31 (Alloy 800). The chemical composition of the alloy is given in Table I. Aging of solution-treated material at 700" and 800°C for 130 and 100 hr, respectively, produced the matrix precipitates shown in Figs. l(a) and l(b). It is apparent from these micrographs that the precipitate particles occurred in the form of thin square plates parallel to the matrix cube planes. Extraction replication and selected-area electron diffraction showed that the precipitates were M23C6. Coherency strains, consistent with the semicoherent nature of small M23C6 precipitates,' were evident for certain imaging conditions. In addition to matrix precipitation, preferential precipitation of M23C6 on dislocations was common, as has been reported previously for austenitic stainless steels.'" Specimens aged for longer times (-300 hr) at 700°C exhibited a different type of coherent matrix precipitate in addition to the M23C6. An example is shown in Figs. 2(a) and 2(b). In addition to the few large M23C6 precipitates, small precipitates exhibiting strain contrastl0,ll are present. The "line of no contrast" of the strain field of a given precipitate lies along differ-

Jan 1, 1970

One of the most unusual assignments in the his¬tory of Loffland Bros. Co. is now in progress with the drilling of a 72-in. diam. shaft in Nevada for the United States Atomic Energy Commission. Projected depth being 3200 ft, by volume, this is the same as a 216,672-ft hole 83/4 in. in diam. Every aspect of the operation is king-sized. The 15,000-lb bit moves into position over the well on a specially-made railroad car riding on rails 14 ft apart. The single drill collar weighs 300,000 lb, is 60 in. in diam., and 43 ft long. The drill pipe is 133/s-in. 72-in. N-80 casing fabricated with special tool joints. The bit chews up 1.05 cu yd of rock for every ft of penetration (This is equal to the volume of 67.71 ft of 83/4-in. hole.

Jan 9, 1964

By C. C. Bailey

THE vendor seeking outside capital for his project has the following potential sources which may be approached; 1--private sources, 2-institutional funds, 3--government agencies, 4--established mining concerns, and 5-public financing.

Jan 7, 1953

By J. R. Guard

Development of electrical power in coal mining has been an outstanding example of adaptbility. It has accommodated itself to new inventions, changing mining methods, increasing demands, increasing safety requirements and many other new conditions. With the appearance of the continuous miner in the mining machinery picture, those engineers interested in the application of electricity to mining have been thinking about what new comination of electrical apparatus will best suit this newcomer. It is the purpose of this paper to discuss the relative costs of supplying d-c versus a-c power to mining equipment with particular reference to continuous miner setups. Assume that a-c power will be delivered to the mine at some high voltage suitable for transmision to the various substation locations. Typical voltage for this purpose is 4000 volts. The problem then is to change the power to some kind of power suitable for driving the motors of mining equipment. For safety and other reasons the voltage to be delivered to the motor terminals must be under 600 volts.

Jan 6, 1950

NOW continuing with the preparation of the moulds I say that it is necessary to give the greatest attention to the differences of the clays as well as to the differences of those things that you wish to mould; and to know that every concavity in the mould produces a convexity and every convexity a hollow following the shape of the original pattern that you have. The pattern should be a body of a harder mated than the thing [78] you wish to mould with and of a substance that is not swollen or disintegrated by moisture. Its archetype may be of marble, bronze, lead, or any other metal, or also of wood, wax, tallow, gypsum, sulphur, or other plaster compositions-in short, of whatever you may have or whatever succeeds best for you, depending on whether the works are large or small and easy or &cult to mould. If you wish to cast them in bronze, you must mould them with loam, covering them with it and then drying it. There are some things in which it is enough to form only one part, such as half- or bas-reliefs. These are easy if they have no undercuts. Some other patterns that are easily handled are formed in two halves, or in three or four pieces, if they are of a hard material. There are also moulds for large statues, which, if one desires to make them of bronze, are first made of wax according to the ordinary procedure. I have in mind to describe every one of these processes in their own place. There are like- wise some moulds that are difficult to make, like scenes on a plane to which figures in full relief are attached, or twisted ornaments or other detached things that cannot be withdrawn from the mould without break-

Jan 1, 1942

By Robert M. Dreyer

Diamond is the hardest known material. The diamond industry is separated into two major segments: (1) industrial and (2) gem. The major industrial use of diamonds is as a high-grade abrasive in a wide variety of applications for which no effective low-cost substitute is available. Table 15.4C.1 gives data on diamond production and on United States diamond imports. In both gem and industrial diamond production, but especially in the case of gems, the quantity of stones produced is not directly correlated to value, for the determination of value is markedly affected by quality. South Africa long has been the world leader in gem diamond production with an estimated production in 1968 (including South-West Africa) of about 4 million carats, equal to 43% of world production. During the past decade there has been a marked rise in gem diamond production in the USSR, so that nation is now the second-ranking world producer, with Angola (Portuguese West Africa) third. In natural industrial diamonds, the major production comes from Congo-Kinshasa (former Belgian Congo) which had a production of 15 million carats in 1968, equal to 47% of world production. In the past six years, there has been a remarkable increase of industrial diamond production in the USSR, which now ranks second with a production of 6 million carats, equal to about one-fifth of world production. South Africa now ranks third followed by Congo-Brazzaville and Ghana. No natural diamonds are produced in the United States. Since the discovery of an economical method for synthesizing small diamonds, there has been a rapid increase in synthetic production from 4 million carats in 1962 (1 carat equals 200 mg) to 11.5 million carats in 1968. Table 15.4C.1 gives the gradually increasing imports of industrial diamonds and indicates a relatively stable price. In 1968, the imports of industrial diamonds were 13.5 million carats with a value of $59.2 million. Table 15.4C.2 shows the rapidly increasing imports of cut and uncut gem diamonds into the United States. In 1968 the United States imported 2.5 million carats of uncut stones with a value of $166 million and 1.5 million carats of cut stones with a value of $175 million. Diamond marketing is dominated by DeBeers Consolidated Mines, Ltd., which, through subsidiaries, controls many of the major African diamond deposits. More important economically, however, through its Central Selling Organization, DeBeers markets 86% of the non-Communist world's natural diamonds, including most of those derived from deposits outside of corporate control. In 1967 the mines owned by DeBeers produced nearly 8 million carats, and the Central Selling Organization sold over $600 million in gem and industrial diamonds. The dominance of diamond sales by

Jan 1, 1976

By Brian W. Mackenzie

In this age of advancing technology, mining companies are confronted with increasing competitive forces. The depletion of high-grade deposits and the development of substitute materials are intensifying market competition. The accelerating activity of petroleum companies in mineral exploration is increasing competition for deposits. At the same time, the trend in government policy is towards a reduction in traditional mineral-industry incentives. To succeed, the mining company must respond to these changing economic conditions by developing a decision-making framework that can effectively contend with the new opportunities and constraints. What are the elements of such a decision-making framework?

Jan 1, 1970

E. A. HOLBROOK,*Urbana, Ill.-To those who have followed the development of powdered coal two questions often occur. First, as to the moisture in the coal. In Illinois we recognize that the bituminous coals contain about 12 to 15 per cent. of what we call "contained moisture," that is, the moisture is present in the coal although this may appear absolutely dry and dusty. In addition, the surface moisture may be present in any amount. I would like to ask what is the relative effect of these two forms of moisture upon the work of pulverizing. Does Mr. Collins refer to the contained moisture or to the surface moisture in estimating the degree to which the coal must be dried? H. R. COLLINS.-In the lignite coals, of which this country possesses a great deal and is beginning to develop them to considerable extent, the "contained" or "combined" moisture does not .trouble us; we have no difficulty in reducing lignites to a high degree of fineness. But when dealing with bituminous, sub-bituminous, or semi-bituminous, we, prefer to reduce the combined moisture as well as the hydroscopic moisture as far as possible. We have recently put into operation, at a plant, furnaces and boilers consuming the lignite from northern New Mexico, which contains between 4 and 5 per cent. moisture as we pulverize and burn it. The evaporating efficiencies under the boilers have been so remarkable that we wish to check the results half a dozen times before quoting them. We have also just started two boilers at the Garfield smelter, and have obtained the same high efficiencies.

Jan 11, 1918

By Walter A. English

CONTENTS PAGE Introduction. By WALTER A. ENGLISH 1 Theory of Seismic Reflection Prospecting. By WILLARD H. TRACY 2 Instruments for Reflection Seismograph Prospecting. By ARTHUR NOMANN 9 Seismograph Field Operations. By FRANK ITTNER 15 Determining Geologic Structure from Seismograph Records. By P. C. KELLY 22 INTRODUCTION BY WALTER A. ENGLISH,* MEMBER A.I.M.E. THE four papers making up this symposum have been prepared espe-cially for those who have no knowledge of seismograph prospecting. To many people mathematics is a formidable subject, and many are discouraged from studying seismograph prospecting under the mistaken assumption that the mathematical requirements are severe. In the papers presented here there is not a single mathematical equation. We believe that considerable competence in dealing with some of the most important problems of this work can be attained without any mathe-matical training whatever. At the present time, there is a real need for interpretation of results by persons thoroughly competent to bring geologic experience and imagination to bear on data that are subject to multiple interpretation from a strictly physical viewpoint. Likewise, those charged with the responsibility of planning seismo-graph exploration campaigns would do well to become familiar with as . much as possible of the technical aspects of the work. They would then be in better position to judge of its success in individual cases. It has often been said that the seismograph is a new structure-finding tool for the geologists to use. Using a tool and using its product are two different things. One does not use an automatic screw-threading machine when he buys a box of screws at the hardware store. Neither does the geologist

Jan 1, 1939

By E. I. Salkovitz, F. W. von Batchelder

AS Slawson1 and others have already shown, from a geometrical view twinning in the diamond structure may be considered as a reflection across a (111) plane or as a reflection across a (112) plane. An analysis by Ellis and Treuting2 showed that the twinning plane must be the (111) plane, but that a twin might have lateral boundaries along (112) planes. Earlier Slawson1 and Ellis3 had shown that only (111) twinning was present in diamond and germanium respectively. Since an ingot of silicon, 1 in. in diam and 1 1/2 in. long, prepared from Dupont silicon to which 0.2 pct Be had been added was available, it was examined for twinning. The ingot had been cooled slowly from the bottom. A section 1/16 in. thick was ground off from the bottom and then the ingot was sliced vertically through the center. Spectrographic analysis indicated only faint traces of iron and silver, in addition to the beryllium. The sample was first etched with a hot solution of 10 pct NaOH in water.and photographed. Back-reflection Laue patterns were made of the vertical and horizontal sections in the regions designated in Fig. 1. Orientations were obtained for each twin using the Greninger technique. Several regions of the same orientation were found; thus regions A and K were identical, similarly N and P, and C, G, J, and L. Knowing the angles between the traces of the twinning plane on the surface and the specimen axis, the indices of the twinning plane were deduced. In all cases the twinning plane was found to be (111); lateral boundaries, however, were found which were (112) such as the one indicated in Fig. 1. Therefore, as in the case of diamond1 and germanium' only (111) twinning occurs in silicon. We wish to thank Mr. Hino for the use of the ingot as well as for its metallographic preparation. References 1C. B. Slawson: American Mineralogist (1950) 35, p. 193. 2 W. C. Ellis and R. C. Treuting: Trans. AIME (1951) 191, p. 53; Journal of Metals (January 1951). 3W. C. Ellis: Trans. AIME (1950) 188, p. 886; Journal of Metals (June 1950).

Jan 1, 1953

PRESIDENT. CHARLES F. RAND,1 NEW YORK, N. Y. PAST PRESIDENTS. CHARLES KIRCHHOFF,1 NEW YORK, N. Y. JAMES F. KEMP,2 NEW YORK, N. Y. FIRST VICE-PRESIDENT. BENJAMIN B. THAY ER,1 NEW YORK, N. Y. TREASURER. GEORGE C. STONE,1 NEW YORK, N. Y.

Jan 4, 1913

By Edwin C. Barringer

IRON and steel scrap has again become page one news, as it was during the war. To many this is anomalous because the common concept is that the theaters of war are literally paved with scrap as the by-product of war damage and abandoned materiel. To an extent this is true, the bottleneck being the ferreting out and transportation of this scrap. While you as consumers of the electric-furnace grades of scrap-the premium grades-are concerned primarily in only one segment of the scrap market, I believe you ill be interested in a general discussion of the market with subsequent funneling down to your specialty.

Jan 1, 1947