Search Documents

By P. J. Burkhardt, L. V. Gregor

The oxidation kinetics of single-crystal silicon has been investigated using extremely dry oxygen as the oxidant. Two techniques were used. The first involved a flow system with which incremental thickness measurements were made. This sytem provided an oxygen ambient at atmospheric pressure which had a moisture content of less than 0.1 ppm of water. The second technique involved measuring the change in volume of oxygen with time in a closed system. A temperature range of 900O to 1200 "C and a pressure range of 20 to 760 Tory were covered. Both techniques showed that a simple parabolic rate law holds only at the higher temperatures. At lower temperatures, the data up to 5000Å can be fitted well to a linear-parabolic equation. The two constants in this rate equation are examined in terms of a physical model. The parabolic portion of the low-temperature oxidatLon fits along the high-temperature curve of an Arrhenius plot. The parabolic rate constant for the flow-system technique can be expressed by k = 2 x 10-9 exp (L 31 kcalRT) sq cm per sec. The manostatic technique gave k = 1 x 10-exp (- 23 kcalRT) sq cm per sec. By extending the thickness range to over 104. a rate law of X = At seems to fit all of the data better than the linear-Pavabolic law. Here the exponent n increases from 0.518 at 1150 V to 0.637 at 900°C. PASSIVATION of silicon planar devices through thermal oxidation is of such great importance that considerable effort has been devoted to the study of the process.17 Much of this work involves hydrothermal oxidation, in which H2O is the oxidant: whereby H2 is produced. It has been proposed that the reaction proceeds by the formation of Si-OH groups and hydroxyl diffusion through the film to react with the silicon surface. Thus, the silicon oxide layer probably contains residual hydrogen in some form after oxidation in H2O and it has already been established that hydrogen has a marked effect on the electronic properties of oxide-passivated silicon surfaces. Silicon is oxidized by oxygen at elevated temperatures; but the rate of oxide formation is considerably lower than that for 0." By using dry O2 as the sole oxidant, the presence of residual hydrogen is presumably avoided. At present, the mechanism of thermal oxidation by dry O2 is a matter for conjecture, and the presence of small amounts of H2O was reported to have a marked effect on the rate of oxide formation10 (perhaps on the electronic properties of the surface, as well). Hence, this study of the kinetics of silicon oxide growth in 0, was undertaken: 1) to determine the oxidation rate at atmospheric pressure in a system designed to exclude rigorously all traces of H2O in the ambient 0,; 2) to obtain oxidation-rate data in situ in dry O2 by means of a continuous monitoring of the amount of 0, consumed during oxide growth. These objectives are complementary—the first assesses what effects (if any) are obtained by excluding H2O from the reaction, and the second expands this information while at the same time avoiding the uncertainty inherent in relying upon incremental measurements of oxide growth to furnish kinetic data. EXPERIMENTAL PROCEDURE The conventional silica open tube in a resistance-heated oxidation furnace is subject to sources of trace H2O, even after the input O2 is thoroughly dried and the outlet gas stream is passed through a trap to prevent

Jan 1, 1967

Edward Halse, Puerto Berrio, Colombia, S. A. (communication to the Secretary): I have read with much pleasure the interesting and valuable paper by Mr. Kunz, and hope that the following brief notes, gathered a few years ago, while a resident in Mexico City, may help to elucidate the subjcct: Turquoise.—This was known to the Aztecs as Xihuitl. Santiago Ramirez states that they found it in the Cerro Xicohtzonc, close to Atzcapatzalco, a suburb of the City of Mexico (compare page 59). Opal.—This was known to the ancient Mexicans, for they named it mezcuitlatt (compare page 63). Jade.—Under this was iucluded a third mineral, prehnite, not mentioned by Mr. Kunz. According to James D. Dana, part of the "jade " of China is prehnite; and Humboldt informs us, in his work on New Spain, that the same species of jade is known in some parts of Mexico as mahagua (majagua ?). The same writer says, in his Views of the Cordilleras, that the Aztec name Tecpatl included flint, hornstone, and green jade; and finally, in his Travels in South America," he discusses the nature of the ancient amazon-stones, and declares them to have been made out of a jade resembling " compact feldspar," one of the constituents of the gabbro verde di Corsica. IIence those stones were probably composed of nephrite. According to Humboldt, the form given to them most frequently is that of the Babylomian cylinder, longitudinally perforated, and loaded with inscriptions and figures. They were also cut by the natives into very thin plates, perforated at the center, suspended by a thread, and worn as amulets. According to the historian Clavijero, the specific name given by the Aztecs to the nephritic stone (jadeite) was Quitzalitztli,

Jan 1, 1902

By Lawrence F. Rooney

One of Edgar Allan Poe's stories that haunts my subconscious is the Masque of the Red Death. These days, whenever I join a group like this, especially during the cocktail parties, I see myself and others as those mythical swingers seemingly isolated from the plague. The world, but this country especially, has had a ball plundering, spending, and wasting its natural resources for 100 years. And, as in days of yore, it is fitting that we end this ball with spectacular fireworks: trips to the moon, so that our grandchildren, huddled in their caves along the Ohio, will better understand how it all began.

Jan 1, 1970

By W. J. Moore, E. M. Swiggard, H. Shenker

Beryllium is the most soluble of the double-acceptor impurities in germanium; the solubility is at least 1 x 10 19 atoms cm3. Photoconductive, optical, and electrical measurements were made on a set of Ge:Be samples grown without other intentionally added imp~ivities. The excited-states spectrum of beryllium in germanium was determined both in zero field and in magnetic fields up to 30 kc. It was found that the absorption 0-f lines in the vicinity of the G line increased markedly with increasing magnetic field. The ioniza-tion energy of neutral beryllium in germanium was determined to be 24.3 * 0.1 mez: using the excited-states spectrum. An infrared detector using a Ge:Be element was found to have a normalized detectivity D* (50 p, 1000 cps, 1 cps) of 9 X ldO cm-~ps"~-w-'. The Ge:Be sambles exhibited low-field breakdown and inibzirity band conduction effects at low temperatures. WHILE the properties of most dopants in germanium have been thoroughly investigated, the properties of beryllium in germanium have had relatively little attention. Much of the work that has been done' has been concerned with the properties of singly ionized beryllium in germanium. The purpose of the present work was to determine the photoconductive and electrical properties of beryllium-doped germanium (Ge:~e) with a small concentration of other electrically active impurities. Ge:Be is of special interest since beryllium is the most soluble of the known double-acceptor impurities in germanium. MATERIALS PREPARATION A set of &:Be crystals with beryllium concentrations between 5 x 1013 and 1x 10'' cmm3 and without other intentionally added impurities was grown in a hydrogen atmosphere by the horizontal zone-refining techniques described by Swiggard and Shenker.2 The segregation coefficient of beryllium in germanium was found to be about 0.07 and its maximum solubility was found to be greater than 1 x 10'' atoms cm-3 which is in agreement with previous results.' Most of the crystals were found to have a small net concentration of shallow acceptors; for example, a crystal having a beryllium concentration of 1.1 X 1016 cm-3 was found to have a net concentration of shallow acceptors of less than 1.5 X 1013 cm-3. Ingots designed to have a beryllium concentration of 1 x 1017 cm-3 or less exhibited a loss of electrically active beryllium. That is, the beryllium concentration was lower than expected and the decrease of the beryllium concentration along the length of the ingot was much larger than expected. It is hypothesized that this effect is due to the oxidation of the beryllium by the residual oxygen in the system. This effect is similar to but not as severe as the effect observed with boron in germani~m.3, 4 OPTICAL ABSORPTION SPECTRUM The excited-states spectrum of neutral beryllium atoms in germanium was studied by measuring the infrared optical absorption spectrum. A typical spectrum is shown in Fig. 1; the labeling of the absorption lines follows that of Fisher and Fan.* The spacings between the observed lines and the D line are nearly equal to the corresponding spacings for the other ac -ceptors in germanium.5-7 By the use of the theoretical result67' that the neutral impurity ionization energy is 2.53 mev larger than the energy of the D line, the ionization energy of neutral beryllium in germanium was determined to be 24.3 * 0.1 mev at 4.2"K. This method yields a more precise value of the impurity ionization energy than the usual Hall effect method.' The absorption spectrum of Ge:Be was also measured as a function of magnetic field using a magnetic field parallel to the incident radiation and using unpolarized radiation. A typical spectrum taken at 30 kG is shown in Fig. 2. An unexpected observation is that the absorption of the lines in the vicinity of the G line (there is a strong possibility that some of these lines may be associated with lines other than the G line) increases with magnetic field. RESISTIVITY AND HALL DATA Measurements of Hall voltage vs temperature were made on several of the samples. The thermal activa-

Jan 1, 1968

By W. F. Chiao

With the application of dislocation damping theory an attempt was made to determine whether the generation and extension of dislocations is inherently more difficult in a brittle steel than in a ductile steel. A ductile steel was compared with a brittle stee1 by simultaneously measuring the ultrasonic attenuation and velocity during tensile test, and the density of free dislocations and their mean loop length were then calculated as a function of strain. The results showed that in the ductile steel there was always a large generation of dislocations and great extension of loop length occurring at some stage within the early plastic region. In contrast, the brittle steel showed very little or no such sudden changes in dislocation dynamic states after the onset of plastic deformation. Furthermore, a strong temperature dependence of dislocation dynamic states was also observed in the ductile steel and a hypothesis was suggested that a thermally activated process of dislocation rearrangement could occur at higher deformation temperatures. The activation energy of dislocation rearrangement at room temperature was estimated as about 2030 cal per mole.C. DUCTILITY is an indispensible property in the application of engineering materials, especially steel. During the past two decades the theoretical and experimental approach to the understanding of flow and fracture of metals has been constantly undergoing changes and progress." while the fracture behavior of metals can be influenced by many factors such as chemical Composition,3 second-phase particle mor-phology,4 and dislocation arrangement,5 it is now a general belief that the fundamental understanding of the ductile-brittle fracture phenomena of solid materials must stem from the study of dislocation dv-namics developed under stress conditions.6,7 Most of the traditional ductility tests, such as Charpy impact test, slow bend test, and tensile fracture test, cannot by themselves reveal directly the mechanisms of ductile to brittle transition of materials. In the experimental investigation of tensile ductility it would be ideal to be able to study directly the dynamics of dis-locations in a bulk specimen during the process of deformation. Since the ultrasonic pulse technique is the only satisfactory method for studying dislocations and the fine details of deformation characteristics in metals in the course of a tensile test, it would appear that a comparative study of ultrasonic attenuation changes during tensile tests of metallic materials exhibiting different ductility might be very informative. So far no work comparable to this study has appeared in the literature. Recent progress in both theory and experiment has indicated the feasibility of studying the dislocation mechanisms of ductility behaviors by ultrasonic measurements during tensile test. Granato and Lucke8 have developed a quantitative theory that enables the calculation of dislocation density and their average loop length from the measurements of ultrasonic attenuation and velocity, and several investigators, including Chiao and Gordon,9'10 have shown that simultaneous ultrasonic measurements can be successfully made during a tensile test. Furthermore, many investigators11-13 have repeatedly proposed in the past several decades that deformation and fracture are mutually self-exclusive, and that the ability or inability of a material to deform plastically, i.e., to generate dislocations, is a major factor in determining whether the material will be ductile or brittle. Thus, in the present work an attempt was made to determine whether the generation and extension of dislocations is inherently more difficult in a brittle steel than in a ductile steel. This article is principally concerned with the study of the relation between the propagation of ultrasonic waves and tensile deformation in a steel series which displays quite different toughness at room tempera-turk. changes in attenuation and velocity of ultrasonic waves have been measured as a function of strain during the deformation process. The results have been interpreted in terms of the vibrating string model for dislocation damping as developed by Granato and Lucke, and it has been found that some of the more subtle predications of the model are in good agreement with the experiments. This would be especially meaningful because most of the previous experiments in testfying the model were carried out with single crystals of high-purity materials and little work has been done with polycrystalline steel alloys. EXPERIMENTAL PROCEDURES AND RESULTS Specimen Materials. The tensile specimens used throughout this experiment were of two compositions selected from a series of Fe-Mo-0.77 pct Mn-0.22 pct C steels prepared for a ductile-brittle fracture transition study. One steel contains 0.21 pct Mo and the other 1.03 pct Mo. These two compositions were chosen for the present study because they possess quite different toughness properties at room temperature. The 0.21 pct Mo steel is quite ductile while the 1.03 pct Mo steel is rather brittle, as measured by the standard Charpy impact test. The alloys had been prepared by vacuum induction melting and chill casting in steel molds. The ingots were hammer-forged into 1/2-in.-sq bars from which tensile specimen blanks were cut. These blanks were first normalized under argon atmosphere at 1700°F and then reaus-tenitized and isothermally transformed at 1050°F to a bainitic microstructure. The chemical compositions, heat treatments, hardness measurements, and Charpy transition temperatures of the two steels are listed in Table I.

Jan 1, 1970

By C. L. Horn

All the tunneling machines discussed in this chapter are Calweld machines. I have divided the machines designed for soft-to-medium formations into three groups, correlated with typical formations and estimated compressive strengths: 1) Running sand and silt requiring blade cutters. 2) Chalk and clay, requiring drag-type cutters, for compressive strengths ranging from 0 to 2000 psi. 3) Sandstones, hard clays, and limestones, requiring disk cutters, for compressive strengths ranging from 2000 to 20,000 psi. All of the soft-to-medium-formation machines are powered by electric hydraulic or diesel hydraulic pumps. The pumps in turn drive hydraulic motors for the torque reaction. The soft-to-medium-formation machines are enclosed in a 360º shield with a cutting shoe, a center portion of the shield housing the mechanical equipment, and a tail shield. Tunnel supports are usually required, and the supports are normally erected in the tail shield. Our first machine was built in 1963, and all but five of the machines illustrated in the figures with this chapter were built in 1966 and 1967. Some of the machines manufactured will be discussed in the following sections; specific features as development has progressed will be pointed out. HARD-ROCK MACHINE The Calweld hard-rock machine has been designed along basic and accepted principles for a hard-rock mechanical borer. The features of this machine are as follows: 1) Direct electric motor drive through a planetary gear reduction ring and pinion gear, and then to the cutting head through a hollow drive shaft.

Jan 1, 1970

By L. C. Brown, E. B. Hawbolt

If a single-phase alloy is rapidly cooled such that insufficient time is available for an equilibrium transformation to occur, the high-temperature phase may be retained to room temperature or may undergo a massive or martensitic reaction. The massive or martensitic product develops without a composition change and usually has a crystal structure approximating an adjacent equilibrium phase. The characteristics of a massive transformation are intermediate between the equilibrium reaction in which long-

Jan 1, 1969

By C. Pin, J. Bruce Wagner

In order to demonstrate the role of defect chemistry in the solid state to a process-metallurgy reaction, laboratory experiments were carried aut to remove copper from liquid lead using lead sulfide which had been doped to provide definite concentrations of cation vacancies. The removal of copper decreases in the order: bismuth- or antimony-doped PbS, undoped PbS or tin-doped PbS, and silver-doped PbS. The data are explained using the simple mass -action law and in terms of the exceedingly rapid interstitial diffusion of coppw in PbS to vacant cation sites. Results are in agree-ment with thermodynamic predictions and certain industrial practices that copper may be removed from lead below the limit of its coexistence with pure Cu,S and pure PbS. The role of defects in solids has been exploited in semiconductors and many device applications, in explaining tarnish formation, dissolution rates, and mechanical properties. The application of these principles to many process-metallurgical problems has not received as much attention. It was the purpose of this study to illustrate the role of defect structures of solids in a process-metallurgical application. When lead is refined, the ore, galena (PbS), is reduced by a series of operations to liquid lead (lead bullion) containing impurities such as copper, bismuth, antimony, arsenic, and silver depending on the original composition, the fluxes added, and the particular type of operation, see Fig. 1. In order to produce a pure lead, a series of refining operations are carried out. A typical lead-bullion analysis before drossing is shown in Table I. Copper is removed first as its presence increases the zinc consumption during the desilverizing process. For preliminary copper removal the lead bullion is brought to a temperature of 440°C in a kettle of 60 metric tons capacity. Some tar (or sawdust or resins) is usually added and the kettle is cooled slowly to 400°C while the liquid is stirred. A solid phase, called a dross, floats on top of the liquid and the particles of the solid phase adhere to the tar. This "hot dross" is collected. It contains mostly lead and copper which are partly oxidized and/or sulfurized if the lead bullion contains some sulfur.*

Jan 1, 1963

By J. S. Kennedy, G. L. Simard, A. A. Lefrew, C. M. Judson, R. B. Booth

DITHIOPHOSPHATE collectors are commonly used in the flotation of sulphide minerals. Studies of the interaction of a typical dithiophosphate collector with galena surfaces have been previously reported from these laboratories.'* These fundamental studies were carried out by employing phosphorus labeled radioactive dithiophosphate. Radioactivity determinations then could be used to measure readily and accurately the small concentrations of dithiophosphate that are present under conditions of flotation processes. Measurements were made on ground mineral, determining the amount sorbed indirectly from the concentrations in solution; and studies were also made with single crystals, determining the amount sorbed directly by counting the crystal surface. The rates, isotherms and reversibility characteristics of dithiophosphate sorption, the competition between phosphate and dithiophosphate for the mineral surface, and the exchange of sorbed dithiophosphate with dissolved dithiophosphate were studied. These studies have now been extended by sorption measurements in flotations with a Fagergren machine. For this work, the selective flotation of galena and sphalerite from quartz was chosen, using ammonium di-(sec-butyl) dithiophosphate as the collector, sodium cyanide as depressant for sphalerite, and copper sulphate as an activator for sphalerite. While the selective flotation of galena and sphalerite using a single dithiophosphate collector is not typical of flotation practice (two different collectors are generally used), it was found that a reasonably good separation could be obtained by using zinc sulphate with the sodium cyanide in the galena flotation and by cleaning the sphalerite concentrate or by carrying out the sphalerite flotation in an alkaline medium. Data of practical importance on the distribution of collector between the concentrates, tailings, and solutions were obtained, particularly with regard to the effect of copper sulphate and sodium cyanide. In addition to the selective flotation of galena and sphalerite from quartz, single flotations of galena-quartz and sphalerite-quartz mixtures were carried out, along with blank flotations on quartz alone. The present paper describes the results of these experiments. As in previous papers, the term sorption is used to designate uptake of collector by the mineral, without implication as to the nature of the processes involved. Experimental Materials: The mineral system was a ground synthetic mixture of galena, sphalerite, and quartz. The galena was from Galena, Kans., and contained 75 pct lead (theoretical 85.6 pct Pb for PbS); the sphalerite, from Ottowa County, Okla., contained 63 pct zinc (theoretical 67.2 pct Zn for ZnS); and the quartz from Klondike, Mo., analyzed as 99.97 pct SiO,. Sulphur labeled radioactive di-(sec-butyl) dithiophosphate was prepared from SS supplied by the Oak Ridge National Laboratory on allocation from the U. S. Atomic Energy Commission. The synthesis consisted of precipitating barium sulphate, reducing the barium sulphate to barium sulphide, acidifying to form hydrogen sulphide, and oxidizing the hydrogen sulphide with iodine to elemental sulphur.

Jan 1, 1953

By J. S. Kennedy, A. A. Lefrew, C. M. Judson, R. B. Booth, G. L. Simard

DITHIOPHOSPHATE collectors are commonly used in the flotation of sulphide minerals. Studies of the interaction of a typical dithiophosphate collector with galena surfaces have been previously reported from these laboratories.'* These fundamental studies were carried out by employing phosphorus labeled radioactive dithiophosphate. Radioactivity determinations then could be used to measure readily and accurately the small concentrations of dithiophosphate that are present under conditions of flotation processes. Measurements were made on ground mineral, determining the amount sorbed indirectly from the concentrations in solution; and studies were also made with single crystals, determining the amount sorbed directly by counting the crystal surface. The rates, isotherms and reversibility characteristics of dithiophosphate sorption, the competition between phosphate and dithiophosphate for the mineral surface, and the exchange of sorbed dithiophosphate with dissolved dithiophosphate were studied. These studies have now been extended by sorption measurements in flotations with a Fagergren machine. For this work, the selective flotation of galena and sphalerite from quartz was chosen, using ammonium di-(sec-butyl) dithiophosphate as the collector, sodium cyanide as depressant for sphalerite, and copper sulphate as an activator for sphalerite. While the selective flotation of galena and sphalerite using a single dithiophosphate collector is not typical of flotation practice (two different collectors are generally used), it was found that a reasonably good separation could be obtained by using zinc sulphate with the sodium cyanide in the galena flotation and by cleaning the sphalerite concentrate or by carrying out the sphalerite flotation in an alkaline medium. Data of practical importance on the distribution of collector between the concentrates, tailings, and solutions were obtained, particularly with regard to the effect of copper sulphate and sodium cyanide. In addition to the selective flotation of galena and sphalerite from quartz, single flotations of galena-quartz and sphalerite-quartz mixtures were carried out, along with blank flotations on quartz alone. The present paper describes the results of these experiments. As in previous papers, the term sorption is used to designate uptake of collector by the mineral, without implication as to the nature of the processes involved. Experimental Materials: The mineral system was a ground synthetic mixture of galena, sphalerite, and quartz. The galena was from Galena, Kans., and contained 75 pct lead (theoretical 85.6 pct Pb for PbS); the sphalerite, from Ottowa County, Okla., contained 63 pct zinc (theoretical 67.2 pct Zn for ZnS); and the quartz from Klondike, Mo., analyzed as 99.97 pct SiO,. Sulphur labeled radioactive di-(sec-butyl) dithiophosphate was prepared from SS supplied by the Oak Ridge National Laboratory on allocation from the U. S. Atomic Energy Commission. The synthesis consisted of precipitating barium sulphate, reducing the barium sulphate to barium sulphide, acidifying to form hydrogen sulphide, and oxidizing the hydrogen sulphide with iodine to elemental sulphur.

Jan 1, 1953

By Walter Crafts

STRUCTURAL steels containing chromium have become widely used in the last 20 years. In the earlier part of this period the major applications were in chromium-molybdenum aircraft tubing and similar special high-strength steels. During the past 10 years there has been a notable expansion in the use of chromium-bearing steel for structural purposes when welding was utilized for fabrication. The chromium-bearing steels introduced by Saklatwalla1 (chromium-copper), Kinzel2 (chromium-manganese-silicon), and Schultz3 (chromium-copper) are being extensively used at the present time.

Jan 1, 1939

By David Moskowitz, Ira Binder, Robert Steinitz

THE hard refractory borides of the transition elements of the 4th, 5th, and 6th groups of the Periodic System have been the subject of a number of recent investigations.'-' It is well known now that most of these elements form several different borides, and Kiessling8 has summarized the rules which govern to some extent the arrangements of the boron atoms in the various structures. Melting points of a few borides have been published." The systems Fe-B, Ni-B, and Co-B have been reported," but, as these borides are rather low melting, they are outside of the groups of boron compounds considered here. Brewer' has tested the stability of various borides and estimated a number of eutectic temperatures between different borides, but in no case was the complete system of a transition metal and boron investigated. The phase diagram becomes of special importance if the preparation of the borides from the elements in powdered form is considered; the lowest eutectic temperature will determine the first appearance of a liquid phase. Also, the knowledge of high temperature phases, if they exist, is important for the preparation of bodies from these borides by hot pressing or sintering. During the investigation of various metal borides,7 it was found that there were more boride phases existing in the Mo-B system than reported by Kiessling." They occur, however, only at temperatures above 1500°C and were, therefore, not found by him. This led to a study of the equilibrium diagram of the Mo-B system. ranging from 0 to 25 pct B and from room temperature to the liquidus. Part of this investigation was reported during the "Research in Progress" session at the 1952 Annual Meeting of the AIME.11 Raw Materials and Preparation of the Borides The raw materials used were commercial molybdenum and boron powder, both supplied by the Molybdenum Corp. of America. The molybdenum powder was 99+ pct pure? while the boron powder contained about 83 to 85 pct B. A large percentage of the impurities in this powder was oxygen, with the rest formed by iron, calcium, and unknown substances. The low purity of the boron used was, however, not considered detrimental to the final product, as most of the impurities evaporated at the high temperatures at which the borides were formed. The final product always had a minimum purity of 96 to 98 pct (figured as molybdenum and boron), with carbon, iron, and probably oxygen being the remaining products. Carbon is usually present as graphite. The chemical analyses always confirmed the compositions which corresponded to the crystallographic structures as determined by X-ray diffraction, and the boron content of the finished product agreed closely with that of the starting mixture; no boron was lost during the boride preparation. The chemical analysis methods employed for molybdenum and boron were previously described by Blumenthal.12,13 The powders were mixed by hand in the desired proportions, compressed at room temperature under low pressure, and then heated under hydrogen to about 1500" to 1700°C in a graphite crucible to form the borides. Usually, the three well-known borides Mo,B, MOB, and Mo,B,, which are stable at room temperatures, were prepared in this way, and all other compositions were made by mixing these borides in various ratios or by the addition of molybdenum or boron powders for the very low or very high boron contents. Preparation of two-phase compositions directly from the elemental powders was tried only occasionally to check whether equilibrium could be reached in this way. Experimental Procedures The stable borides were mixed in the desired ratios and heated under hydrogen in graphite crucibles to various temperatures. The well insulated crucibles were heated in a high frequency induction furnace. Special care was taken to obtain exact temperature measurement, which proved much more difficult than originally anticipated. It is believed that individual temperature measurements have an error of less than ±25ºC, while melting or transformation temperatures are accurate within ±50°C. The temperatures were measured with an optical pyrometer which was aimed at the closed end of a graphite tube extending down into the crucible. close to the samples. Attempts to measure directly through the hydrogen exit stack failed. The crucible arrangement is shown in Fig. 1. Heating was done at a slow rate to be sure that the temperature inside the crucible was uniform. The specimens were kept at the final temperature for about 30 min. For the investigation of high temperature phases, some samples were quenched. They were heated, without atmosphere protection, in a very small graphite crucible which could be rapidly removed from the high frequency coil, and dropped into water. These quenched samples were afterwards annealed to establish the equilibrium at lower temperatures. The melting points or the positions of the solidus and liquidus lines were determined by heating the specimens to various temperatures and examining them at room temperature for evidence of a liquid phase. These results were checked later on by thermal arrest curves, especially to determine the exact position of the eutectic temperature line. For this purpose about 200 g of the boride were melted in a graphite crucible, in an arrangement similar to Fig. 1. Slow cooling was assured by very good

Jan 1, 1953

By Stuart McGill

This case-study of the financing of the Ok Tedi project illustrates the nature of project financing and outlines the arrangements made in the case of this project; it also demonstrates that the limitation of financial exposure is an important goal for Governments involved in developing the resources sector. The account includes a chronological description of the process by which the sponsors prepared for the financing of the project and the lenders became involved in it. The type of security arid loan documentation required for such financing is described, together with a broad analysis of their content and the manner in which the various risks involved in development are apportioned among the sponsors and lenders. The ability to apportion and limit financial liability is an important development for the owners of capital and resources.

Jan 1, 1985

By Jim V. Rouse

In situ mining and dump leaching has been practiced for years. Recent environmental concern over conventional mining and milling techniques has rendered in situ mining more attractive. While there are many environmental advantages to in situ mining, there are disadvantages which, if ignored, can lead to environmental damages, followed by stringent control. The environmental advantages and disadvantages of the various types of in situ mining operations are discussed. Current legislation and regulations governing in situ mining are cited, together with a suggested program of environmental monitoring designed to protect the mining company as well as the environment. Suggestions are made for possible solution of existing pollution problems associated with previous mining activities by heap-leaching techniques. Present and indicated control of subsurface injection is traced, because of the many similarities in philosphy and monitoring requirements to in situ mining.

Jan 1, 1974

By V. T. Stringfield, H. H. Cooper

ONE of the earliest investigations of ground water in Florida was made in 1513 when Ponce de Leon arrived at St. Augustine in search of the Fountain of Youth. The history of the development of the water resources of the State shows that the large artesian reservoir that underlies Florida was discovered in the latter part of the last century. Part of that history is given by L. C. Johnson' who states that the first successful artesian well in Florida was drilled at St. Augustine between 1880 and 1882. After the City of Jacksonville failed to obtain a flow of artesian water at a depth of nearly 400 ft and abandoned the drilling, R. N. Ellis, City Engineer, and L. C. Johnson, using Johnson's knowledge of the geologic structure of the artesian reservoir, estimated correctly that artesian water could be obtained at a depth of about 500 ft. Thus began the development of the large artesian system in the northeastern part of the State. In 1908, the Florida Geological Survey issued its first report on the ground water of central Florida. More recent reports give the results of investigations that have been in progress in cooperation between the Florida Geological Survey and the U. S. Geological Survey since 1930. As a result, the ground-water geology and hydrology of Florida are now so well known that ground-water problems such as confronted early investigators no longer exist. However, new problems arise and new discoveries are made as the demand for more ground water increases with the development of the State. Water-Bearing Formations Descriptions of the geologic formations and a map showing their distribution at the surface are given in a recent report by Cooke.' The geologic formations that yield the ground-water supplies in Florida represent only a small part (about 1000 ft) of the total thickness of the sedimentary rocks (more than 15,000 ft) that underlie Florida. The water-bearing rocks that yield fresh water include more than two dozen formations that range in age from Eocene to recent. The Eocene formations, which consist chiefly of limestone, are the oldest and the deepest of the formations in Florida that yield fresh water to wells. In 1944, on the basis of a study of the foraminifera, the Applins -ivided the limestone of Eocene age into six formations, which are as follows, from top to bottom: Age or group Formation Jackson Ocala limestone icAvon Park limestone Claiborne -j Tallahassee limestone aLake City limestone Wilcox Salt Mountain limestone xOldsmar limestone The Ocala limestone and the underlying formations of Claiborne age, along with some of the overlying limestone of Oligocene and Miocene age, constitute the principal source of water in Florida and southeastern Georgia and generally may be regarded as forming one artesian aquifer or water-bearing unit. This aquifer is referred to in this paper as the Floridan aquifer, a name proposed by Parker.' In part of Seminole County alone more than 1000 flowing wells yield water from the Floridan aquifer. A yield of 6500 gpm, or about 9.5 million gal per day, by natural flow from a well penetrating the aquifer at Jacksonville, Florida, was observed in 1942. A yield of about 7000 gpm by natural flow was reported for a well 1390 ft deep at St. Augustine in 1887. The largest yield reported from a pumped well penetrating the aquifer is 7500 gpm, or about 10.5 million gal per day. The aquifer is also the source of some of the large springs, such as Silver Springs, whose discharge, according to measurements made by the U. S. Geological Survey, has ranged from 526 to 1350 sec-ft, or from 340 to 872 million gal per day. The top of the Ocala limestone, as represented by contours in Fig. 1, indicates in a general way the geologic structure of the formations that comprise the Floridan aquifer. The Ocala is at or near the surface in the areas represented by shading in the northwestern part of the peninsula and also in an area in western Florida adjacent to Alabama and

Jan 1, 1952

By V. R. Garfias, R. V. Whetsel, J. W. Ristori

Preliminary estimates indicate that world consumption of petroleum and related fuels in 1938 will be close to 1,908,000,000 bbl., or approximately 7,000,000 bbl. less than in 1937. This total does not include military consumption in foreign countries, which for obvious reasons is not made public. Foreign military consumption in any one year, however, is approximately represented by the difference between the total production of petroleum and related fuels and the "partial total" consumption above noted, after adding any decrease, or subtracting any increase in stocks in the United States. Fig. 1 illustrates this "difference" and shows that in 1937 and 1938, owing to the wars in China and Spain and the possibility of armed conflict in Central Europe, foreign military consumption—and possibly additions to foreign stocks—increased nearly 70,000,000 bbl. in 1937 over 1936 and remained at this high rate throughout 1938. No official information on foreign oil stocks is available to the writers. Table 1, recently published, purports to give the oil in storage in some of the European countries, but it is not known whether the figures include oil stocks for military purposes. It should be noted that with the annexation by Germany of Austria and part of Czechoslovakia the consumption of the country has increased to 53,000,000 bbl., which is about 36,000,000 short of the German produc-

Jan 1, 1939

By J. W. Ristori, R. V. Whetsel, V. R. Garfias

Preliminary estimates indicate that world consumption of petroleum and related fuels in 1938 will be close to 1,908,000,000 bbl., or approximately 7,000,000 bbl. less than in 1937. This total does not include military consumption in foreign countries, which for obvious reasons is not made public. Foreign military consumption in any one year, however, is approximately represented by the difference between the total production of petroleum and related fuels and the "partial total" consumption above noted, after adding any decrease, or subtracting any increase in stocks in the United States. Fig. 1 illustrates this "difference" and shows that in 1937 and 1938, owing to the wars in China and Spain and the possibility of armed conflict in Central Europe, foreign military consumption—and possibly additions to foreign stocks—increased nearly 70,000,000 bbl. in 1937 over 1936 and remained at this high rate throughout 1938. No official information on foreign oil stocks is available to the writers. Table 1, recently published, purports to give the oil in storage in some of the European countries, but it is not known whether the figures include oil stocks for military purposes. It should be noted that with the annexation by Germany of Austria and part of Czechoslovakia the consumption of the country has increased to 53,000,000 bbl., which is about 36,000,000 short of the German produc-

Jan 1, 1939

In reply to inquiries and comments which have reached me since the publication of this paper, and in explanation of some seeming discrepancies between my statements in the text concerning the amount of displacement of the faults, on one hand, and certain figures in the plates on the other hand, I give here, with some additional remarks, my measurements of the displacements in the different sections, which it originally seemed unnecessary to print : By displacement, I mean neither the throw, i.e., the vertical distance apart of the two edges of a faulted bed (what Mr.

Jan 1, 1896

By R. T. Hukki

This paper presents a series of equations for mechanical ball wear, relating parameters of ball size, mill speed, and mill diameter. The fundamental equation, Eq. 12, presented here is introduced to correlate these basic parameters and thus define and clarify the concept of ball wear. This equation is offered as a general rule, which may be modified to apply to individual problems of grinding. BALL wear as observed in grinding installations is the combined result of mechanical wear and corrosion. Corrosion should be a linear function of the ball surface available. Ball corrosion, however, has been studied so little that its effect, although of great importance, cannot be included in the analyses given here. In a separate paper' it is shown that 1 n = 0.7663 np----=— rpm [1] vD P = c, np D kw [2] T=c²(np)n De tph [3] In these equations n — actual mill speed, rpm np = calculated percentage critical speed D = ID of mill in feet P = power required to operate a mill, kw T = capacity of a mill, tph C¹ and c² - appropriate constants in = exponent of numerical value of 1 5 m 1.5 Exponent m is the slope of a straight line on logarithmic paper relating mill speed (on the abscissa) and mill capacity (on the ordinate). It is generally accepted, although not sharply defined, that ball wear in mills running at low (cascading) speeds is a function of the ball surface available. Accordingly, the wear of a single ball may be considered to be a homogeneous, linear function of its surface and of the distance traveled. Thus dw = f¹(d2) . f2(ds) [4] where dw is the wear of a single ball in time dt, d the diameter of the average ball in ball charge, and ds the distance traveled by the ball in time dt. Indicating that ds - a D n dt, the wear of the average ball in time dt becomes dw = f¹(d2) . f2(Dn dt) 1 --- f¹ (d1) f² (D c3 np-----— dt) \/D = c,d² n, D dt The rate of wear of the average ball is given by dw/dt. dw/dt = c, d² np D lb per hr [5] The weight of the ball charge per unit of mill length is a function of D The number of balls of size d in the ball charge is = f³(D2)/f4(d³). The rate of wear of the total ball charge equals the number of balls times rate of wear of the average ball. Thus rate of total ball wear = — . (dw/dt) w. c, . (l/d) . n,, D lb per hr [6] which is the equation of ball wear in low speed mills. In a mill running at a low speed, grinding is the result of rubbing action within the ball mass and between the ball mass and mill liners. When the speed of the mill is gradually increased toward the critical, the impacting effect of freely falling balls becomes increasingly prominent in comparison with the rubbing action. Reduction of ore takes place partly by rubbing, partly by impact. The share of the freely falling balls in the reduction of ore reaches its practical maximum at a speed somewhat less than the critical; at that speed grinding by rubbing has decreased to a low value. It may be reasonable to think that size reduction by freely falling balls should reach its theoretical maximum at the critical speed, if the fall of the balls were not hindered by the shell of the mill beyond the top point; grinding by rubbing would cease at the critical speed. As a first approximation, wear of freely falling balls may be considered to be a homogeneous, linear function of the force at which they strike pieces of rock and other balls at the toe of the ball charge. The force equals mass times acceleration. The mass of a ball is a function of d3 and its acceleration is a function of the peripheral speed of the mill. The wear of a single ball of size d representing the average ball in a ball charge will therefore be w¹ = f3(F) = f (d3) f7 (v). [7] Indicating that v = D n, and n = c³ np 1/vD, Eq. 7 becomes W1 = cn d3 np Do.5 lb per hr. [8] Total wear of the ball charge equals number of balls times the wear of the average ball. Number of

Jan 1, 1955