Search Documents

By A. P. Coldren, V. Biss

SINCE the r ? a transformation rates of many carbon-free ferrous alloys and low-carbon alloy steels are relatively fast, conventional equipment is not suitable for the dilatometric determination of continuous cooling transformation diagrams. On the other hand, a method based on metallographic analysis of quenched specimens would not be practicable because the various products of shear-dominated transformation are essentially indistinguishable in low-carbon iron-base alloys. Both problems may be avoided by a thermal analysis method employing gas quenching of small specimens austenitized in vacuo. The laboratory equipment employed in the present study consisted of a Tektronix Type 564 Storage Screen Oscilloscope and a Kinney high-vacuum evaporator, modified as shown in Fig. 1, to permit heating a small specimen and cooling it slowly by programmed cooling or rapidly (up to about 8000°F per sec) by a controlled quench with helium gas. The oscilloscope records the electromotive force of a 40-gage (0.003-in.-diam) Chromel-Alumel thermocouple in the specimen during cooling. The temperature at which the cooling curve begins to show the influence of the heat produced by the phase change in the specimen was arbitrarily taken as the transformation-start temperature.*

Jan 1, 1970

By Paul Rhedey

Various commercial pelroleum cokes were heat-1,reated at temperatures between 500° and 1500°C, in a nitrogen atmosphere, in laboratovy induction furnaces. The rate of tenlperature rise was varied betzveen 10" and 300°C per min, or the green cokes were flash-calcined, orv a combination of heating rates was used. Changes in the rate of heating had only negligible effects on the degree of' calcination as characterized by mean crystallite thickness and the chemical properties of the calcined coke. The physical structure of the cake was however significantly affected when rate of heating during calcination exceeded 50°C per min over the temperature range of 600° to 900°C. Surface-accessible porosily increased with the .rate of temperature rise, and this was accompanied by a change in pore size distribution. Source and properties of the green coke also had an influence on the structure of the calcined coke. The evidence presented suggests a similar mechanism of porosity development in petroleuiiz coke during calcination in industvial equiplnenl, such as rotary kilns. An increase in surface accessible povosity incveased the pitch binder requirement when the coke was used as aggregate in Soderberg paste. A correlation was established between calcined coke porosity and paste binder requiremenl. ManY results have been published on the changes of properties of petroleum coke during calcination, such as chemical composition, real density, electrical resistivity, crystallite and pore structure. The correlation of these properties with temperature of calcination and time at maximum temperature has been rather well established in both laboratory and pilot plant experiments. Surprisingly little attention has been given however to the effect of calcination conditions, such as rate of temperature rise or furnace atmosphere, on the chemical and structural properties of the calcined coke. It has been observed that petroleum coke, when calcined in industrial equipment, acquires higher porosity and lower real density than those attainable in laboratory furnaces at apparently identical calcina- tion temperature and soaking time. This paper describes a study of the effect of rate of heating during calcination on calcined coke properties using green petroleum cokes of different volatile matter, hydrogen, and sulfur content. An attempt was made to correlate the changes in coke structure with the flowability of anode paste of the type normally used in aluminum reduction cells. EXPERIMENTAL Petroleum Cokes Used. In the study of release of volatile matter and sulfur during calcination and the effect of rate of heating on calcined coke properties two delayed cokes of different sulfur contents were used. The results of analysis of the green cokes are given in Table I. In the study of the effect of flash calcination thirty-six commercial petroleum cokes from twelve different refineries were used with a range of properties shown in Table 11. Calcination Conditions. Calcination experiments were carried out in a laboratory induction furnace. In each run a 200-g sample of dry green coke sized to 10 by 65 Tyler mesh was calcined in a graphite crucible. The crucible containing the sample was placed in the middle of a stack of eight others filled with metallurgical coke to reduce temperature gradients within the sample. Temperature was measured by two Pt, Pt-10 pct Rh thermocouples and controlled by a Celectray instrument. The two couples generally agreed within 5°C. In the study of volatile matter and sulfur release the samples were heated to temperatures in the range of 500" to 1500°C at a rate of 10°C per min in a nitrogen atmosphere and held at the final temperatures for 30 min. In the study of the effect of heating rate on calcined coke properties the desired rates between 10' and 300°C per min were obtained by manually adjusting the power input. Flash calcination was carried out by dropping 100 g of the green coke into the graphite dish preheated to the calcination temperature. Because of the small heat capacity of the furnace the coke was introduced in 20-g portions at a time. For this purpose a 2-in.-long nipple between two 1-in. gate valves installed on the top flange of the furnace served to provide a gas seal while feeding coke to the furnace. It was estimated that the temperature of the coke reached that of the furnace at a rate of approximately 1000°C per min. Holding time at final temperature was also 30 min. Calcined Coke Proper- Determined. Porosity was determined on 20 by 35 Tyler mesh samples using an Aminco-Winslow mercury pressure porosimeter with an operating range of 1.8 to 3000 psi absolute pressure (100 to 0.05 p pore diameter range).' Apparent density was obtained by the mercury poro-simeter. It represents a particle density of the 20 by

Jan 1, 1968

By Oliver Bowles

Two striking events marked the year 1871-the establishment of the A.I.M.E. and the beginning of the portland cement industry, the most spectacular of all the nonmetallics in its development. Just as David Saylor's first portland cement, made in a little mill at Allentown, Pa., in that year was the forerunner of a mighty industry, the products of which in 1942 were made in 155 plants scattered throughout the country (having attained a value of nearly $300,000,000), so the Institute from its small beginning has attained a membership of many thousands, likewise decentralized into a series of individual sections of wide geographical distribution. Concurrent with the establishment of the Institute was also the invention of the steam drill, followed by the compressed-air drill about 1904. These mechanical drills were so immeasurably in advance of the hand drill and hammer used previously that quarrying and mining of present-day magnitude could never have been attained without them. Some outstanding occurrences have marked this eventful three quarters of a century. The concrete age, with its enormous demands for cement, aggregates and steel, is of primary importance. Of interest also is the shift of fertilizers from the organic to the mineral field. Nitrates, primarily obtained

Jan 1, 1947

From the cold Pacific waters in June rolls a blanket of white clouds that tucks up around the mountains at around 8000 or 9000 ft. This is the way it happens in southern Peru and so the mining operations and daily living at Toquepala have an ethereal quality not often encountered. Besides looking down on the clouds from the brightly sunlit mountain tops, one can discern the trace of a different era in the brown barren mountain slopes. This trace is like a delicate net laid over the surface of the earth-a criss-crossing of innumerable trails that are so omnipresent, yet faint, that the local people have long since ceased to notice them. It is difficult at first to ask about them because no one understands what you are talking about. It finally comes out though, that the markings are indeed trails, but fossil trails made by animals in times when they were in abundance in a countryside that was green in some bygone century. In a way Toquepala is still pristine, it is the way the engineers planned it-from the ground up. There are no additions or expansions- those tackings-on that spoil the symmetry of design while increasing the profit. This does not deny that annual production has gone up over the years. Daily mill throughput has been increased from 30,000 to 42,000 tpd. Initial design of the concentrator was for 30,000 tpd but in 1964-65 milling capacity was increased to 36,000 tpd at a cost of $3 million.

Jan 11, 1969

By Evert Hoek

SYNOPSIS It can be shown that the properties of intact rock are relatively unimportant in rock slope stability and that failures are controlled by structural discontinuities such as bedding planes, joints and faults in the rock mass. The frequency, orientation and inclination of these discontinuities as well as their strength characteristics are important factors to be considered in any rock slope analysis and their influence will be demonstrated by means of a number of practical examples. Methods for determining the mechanical properties of discontinuities will be reviewed and the interpretation of the strength test results for use in stability computations will be discussed.

Jan 1, 1971

By Robert L. Taylor, Richard E. Goodman

A complete rational analysis for design of excavation slopes and loaded rock masses is a desirable but perhaps unattainable goal. Irregular external and internal boundary conditions, poor understanding of failure criteria for large masses of rock, capricious material properties, and the importance of indeterminate forces and inaccessible and virtually unsampleable rock defects emphasize the importance of experience in this aspect of rock engineering. The experience must be correlated with geological factors. In certain regions the accumulation of such experience through the observation of existing rock slopes in various formations constitutes an important aspect of studies for design of rock excavations. In former times an accepted method of rock construction consisted of trials and adjustments. This approach is not often compatible with present methods of contract management. With the development of improved instruments and warning devices such as inclinometers, piezometers, relays, stress meters, and rock noise detectors, modified trial procedures of rock construction may reappear in specific applications. In spite of the great advances made, development of methods to predict the performance of rock slopes, abutments, and foundations deserves vigorous effort. Two distinct approaches may be taken. The rock mass in question may be considered a continuum and the stresses and strains throughout the region of influence of the work may be calculated. Or, the rock mass may be described as a discontinuum whose stability calculation involves the statics and kinematics of accumulations of rigid blocks. The prototype must lie in the range between these contrasting models. As yet, however, there is little reconciliation between the two methods

Jan 1, 1967

By P. S. Rudman

The solubility limit and the diffusivity of carbon in molybdenum have been obtained by duffising carbon into molybdenum rods from a Mo + Mo2C powder mixture. The solubility limit was taken as the long-time asymptotic limit of the rod composition. The diffusiv-ity was obtained from fractionally saturated rods from the rate of change of the average composition. Compositions were determined by chemical analysis. The solubility limit obtained is: WhILE the Mo-C system is important in refractory alloy technology neither the solubility limit nor the diffusivity of carbon in molybdenum is unambiguously known. In Fig. 1 the Mo-C phase diagram is presented. The heavy lines, the terminal solution solubility limit, and the eutectic temperature are results of the present investigation and will be discussed in detail later. However, it is readily seen that the previously published solubility limit determinations, Few and Manning1 and Fromm and ROy2 differ by up to an order of magnitude. The general form of Fig. 1, the Mo2C field, and a eu- tectic temperature -2200°C are due to an early Investigation by Sykes et a1.3 Although they did not determine the solubility limit, they did establish that the maximum at the eutectic temperature was about 1000 ppm. The only other prior data found on the solubility limit is from a lattice-parameter study by Speiser et a1 .,4 from which it can be concluded that the maximum solubility is greater than 1800 ppm. There does not appear to be any data oh the diffusivity of carbon in molybdenum. However, Samsonov and Epik5 have determined, from the rate of growth of an MozC layer, the diffusivity of carbon in Mo2C, and this has been erroneously interpreted, for example by ~c~eil,' as applicable to diffusion of carbon in molybdenum.

Jan 1, 1968

By M. E. Wadsworth, J. S. Cho

The kinetics of silicate adsorption from aqueous colloidal (SO2 . nH2O) silicate sols on thoria (ThO 2) surfaces were determined at 100, 150 and 200°C in an autoclave system. The amount of chemisorbed silica on the thoria surface was determined by means of infrared spectroscopy. First order kinetics were observed in all cases with the anomalous result that the first order rate constant was found to vary with the initial amount of silica added to the system. These results have been correlated quantitatively by means of a strain model of adsorption involving two types of surface silicate bonding, both of which may be readily observed in the infrared spectrum. Initial adsorption occurs rapidly to produce one type of surface silicate followed by a slow transition to a second type of surface bonding, the latter transition representing the slow step in the adsorption process. Initial interest in silicate adsorption on thoria arose from the dispersive effect silica has on finely divided thoria in aqueous suspensions. Spaepen et al studied the equilibrium adsorption of silica on thoria and noted increased adsorption up to approximately 215°C with a notable decrease in adsorption at temperatures above 215°C. Similar results were observed by Cho and Wadsworth2 who identified two types of surface silica by infrared spectroscopy. At temperatures of 100°C and above, rapid initial adsorption occurred producing a surface species with maximum infrared absorbance at 9.4 After extended periods of time, the 9.4 species converted to a more strongly bonded surface silicate with maximum infrared absorbance at 10.3. The latter was very strongly bonded and difficult to remove by desorption in hot distilled water, while the 9.4 species could be removed more readily by similar treatment. The 9.4 and 10.3-p species were distinguishable from free unadsorbed silica which had maximum infrared absorbance at 9.1 The kinetics of the formation of the strongly chemisorbed silica (10.3) on thoria as determined by infrared examination are presented in this study. EXPERIMENTAL PROCEDURE As a source of silicate, Ludox SM (16.36% SiO2) or Ludox HS (30.25% SO2), DU Pont colloidal silica in aqueous suspensions, was added directly to a thoria slurry made up of one liter of distilled water and one gram of thoria. The thoria used was designated D-16-650 and was received from the Chemical Technology Div. of Union Carbide Nuclear Co. It was prepared by firing thorium oxalate at 650°C. The D-16 thoria had a surface area of 32.4 ± 0.6 sq m per g as determined by nitrogen adsorption.* This thoria 'Determined by Unlon Carbide Nuclear Co., ORNL. had a total adsorption capacity for silicate of approximately 19.4 mg of silica per gram of thoria.1 This amounts to approximately one SiO2 molecule for every surface thoria site. In all cases in this study.

Jan 1, 1963

By A. K. Snelgrove

This symposium is designed to marshal a state-of-the-art account of approaches and solutions to problems arising out of waterlogging and salinization in the world's largest irrigation system which was dismembered by legal beheading of the Eastern Rivers under the lndus Waters Treaty of 1960. In this introduction, the geological and historical backgrounds of surface waters and groundwaters in the Indus Basin are presented with a summary of remedial measures undertaken and proposed to combat waterlogging and salinization. At a time when water-resource planning is proceeding on a continental scale, a study devoted solely to the Indus River Basin may seem to require an apologia. None is offered, however, for three major reasons: (1) Although the Indus is a single river basin, it is one of great magnitude and importance. The Indus River, which comes from Himalayan sources to form part of the great Indo-Gangetic Plain drainage system, is vital to agriculture and hydroelectric power in the thickly populated northern subcontinent of Indo-Pakistan. (2) The Indus has become a plexus of extraordinary problems since the dismemberment of the world's largest irrigation system of which it was a part. The break-up of this system occurred with the legal beheading of the Eastern Waters under the Indus Waters Treaty of 1960. (3) Th River Basin has been the target of a Herculean effort to contain the twin encroachments of waterlogging and salinization that now threaten it with a shortage of fresh water. The British irrigation system of barrages and canal on the Indus was a venture admirable in conception. Unfortunately, it is now a legacy burdened with unwanted consequences due to interference with the hydrological regimen, particularly the rise of water table occasioned by leakage. To cope with this situation, there has been a possibly unprecedented concentration of domestic and international engineering and scientific talent on the Indus and its problems (about a score of organizations by recent count). To marshal a state-of-the-art account of their approaches and solutions is the purpose of this Symposium. The coordinated effort now being made on a variety of fronts under the general supervision of West Pakistan Water and Power Authority (WAPDA) is directed toward the modification and control of interactions and relationships between geological materials — soils, water and its salt balance, and air —in what has been termed a huge "underground lake" in an alluvial basin. The problem is an intriguing one in that a highly complicated case history of river-course changes visible in the present surface must be projected downwards through Recent and Pleistocene sediments in order to decipher the environmental controls of deposition in terms of vertical and lateral variations in lithology and patterns. Such studies must be extended to compaction, deformation, and fabrics of the alluvium. Geohydrology is often defined as groundwater hydrology. As employed herein, it includes the distribution, quality, and behavior of surface and subsurface waters, including their evolution, vagaries, and geological, climatological, and botanical milieux." GEOGRAPHY The Indus (Sanskrit, Sindhu = river) rises at nearly 17,000 ft above the sea in the glaciers on the northern slopes of Kailas Parbat, Tibet. It is about 1800 miles long and has a total drainage area estimated at 372,000 sq miles. The average discharge is 196,000 cfs at mouth. Leaving the Plateau of Tibet, the river flows at a level which is miles above the sea, and in places miles below Himalayan peaks, in a structurally controlled northwestward course. Joined in this course by six tributaries and swollen by the melt waters of giant glaciers, it swirls about the base of the famous

Jan 1, 1970

By M. D. Hassialis

THE claim is made in a number of patents1,2,3,4 that some compounds of the class known as aryl sulphides have collector properties. One of these patents generalizes the claim to include all aryl sulphides, whose generic formula is R-S¬R[=]-R’ (where x = r,2, . . . ), with the restriction that if the aromatic radicals R, R' contain substituent groups these groups may not contain nitrogen or oxygen. Moses, Hess, and Perkins cite as evidence for their claims the results of flotation tests on Anaconda and Miami copper ores using Biphenyl sulphide, ditolyl disulphide and dinapthyl disulphide as collectors. The use of alkyl sulphides as collectors has also been reported5 with the conclusion that the alkyl sulphides are better collectors than the corresponding aryl sulphides. The experimental work cited appears to confirm this contention. In order to test these claims with respect to diphenyl sulphide, a sample, purchased from the Eastman Kodak Co., was tested against Anaconda ore. The procedure followed was that of Moses, Hess, and Perkins. A sample of ore weighing 500 grams was placed in a laboratory ball mill. To this was added 220 grams of water, 0.06 grams of commercial diphenyl sulphide (1/4 lb. per ton of ore), and 0.8 grams of lime (3 lb. per ton of ore). The material was ground until 93 per cent passed a 65mesh screen. This pulp was diluted to 16 per cent solids. A sample of the diluted pulp was placed in a Minerals Separation type of laboratory flotation cell. After a 2-min. agitation period, pine oil was added and the froth collected for a period of 15 min. This test recovered 68 per cent of the copper, with a ratio of concentration of 6.8: 1. The tailing assay was 0.3 per cent Cu. Moses, Hess and Perkins attained a recovery of 75 per cent, with a ratio concentration of 12: 1. Although these results do not compare too well with those of Moses, Hess and Perkins, subsequent tests showed an improvement, as judged by vanning of the tails. It is concluded, therefore, that the patent results are confirmed. CONTACT-ANGLE TESTS In order to study the response of the various minerals, found in Anaconda ore, to commercial diphenyl sulphide, some contact-angle tests were made. Polished particles of bornite, chalcocite, chalcopyrite, pyrite and quartz were conditioned for 15 min. in a suspension of diphenyl sulphide in water. The concentration of this suspension was 0.284 grams per liter, this being the concentration of this reagent in the ball mill. The conditioned particles were rinsed with water (not rubbed with filter paper or boiled linen) and then tested against an air bubble in the bubble machine, with the following results: born-

Jan 1, 1943

By John M. Dealy, Robert D. Pehlke

Values for interaction parameters in nonferrous systems, as calculated from published data, are tabulated and discussed. The influence of temperature on the parameter is derived and compared with the results of the literature study. Wagner's relationship between the interaction parameter and the self interaction coefficients is compared with the tabulated data. A problem which has been of considerable interest in the field of metallurgy is the prediction of the effect of one alloying element present in dilute concentration on the thermodynamic properties of another dilute alloying element. Ultimately, the prediction may be accomplished entirely from statistical mechanical considerations. At the present, however, the problem remains unsolved since liquid solution models which are simple enough for analytical treatment are inadequate for such purposes. Thus, we desire some means of organizing the information on dilute systems which will serve as a guide for further study on interactions in dilute alloys, and also provide a basis for the utilization of thermodynamic data in the engineering design of alloys.

Jan 1, 1963

By H. Cecil Spicer

THE results described in this article are based on field work conducted during the periods April-May, 1939, and May-July, 1940. The United States Potash Co. is mining potash on Government land under a permit from the Department of the Interior and the geophysical investigation was completed under a cooperative arrangement made between that company and the Conservation Branch of the Geological Survey. The writer, a member of the Section of Chemistry and Physics of the Geologic Branch, was assigned to this investigation. Four definite objectives were in mind for the geophysical work in the studies over the salt deposits. The first was to determine the measure of success that could be attained in this type of work with the resistivity methods that were to be employed. These methods had been introduced into the work of the Conservation Branch by Benjamin E. Jones for the investigation of dam sites, and have been used under his direction by the author for such work. If the method proved to be applicable, an effort was to be made to contour the top of the salt beds and also the other formation boundaries known to be present in this area. Salt-water aquifers were to be studied in an effort to determine their boundaries, and an attempt was to be made to delineate the potash-bearing beds. EARLIER STUDIES Others have made, and reported, resistivity studies over saliferous deposits in different areas. Friedel1 and Messrs. Schlumberger2 reported geophysical work performed in the discovery of the salt domes of Alsace; Carrette and Kelly3described the geology of the same area. Leonardon and Kelly4 published a resistivity curve obtained over the Hettenschlag dome, and a further discussion of this same area was given by the Messrs. Schlumberger5 in a communication. Messrs. Alty6 described studies on salt deposits in which the single-probe method was used. Sinerez7 mentions that electrical methods were tried over salt deposits in Spain. Geoffrey and Charrin8 show a resistivity curve obtained over marl, gypsiferous marl and salt which is similar to that obtained over the New Mexico salt deposits. Kelly9 reported resistivity work performed with the ground comparator of Zuschlag over the salt deposits near Syracuse, N. Y., where the Salina formation is at a depth of 700 to 8oo ft. Some structural studies on the potash basin of Alsace are described by Poldini.10 Another single-probe resistivity study, made over salt deposits in New Mexico, is briefly described by Heiland,11 through the courtesy of Harry Aurand, of the Midwest Refining Co.

Jan 1, 1941

By H. A. Schwartz

THE spheroidal form of the temper carbon nodules in malleable cast iron and of the graphite mottles of "mottled" cast iron suggests that in both all the graphite in a given mottle or nodule grew from a single center of crystallization or nucleus. ? There is, however, a distinct metallo-graphic difference between the mottle and the nodule; the area of mother metal impoverished in combined carbon by the crystallization of graphite in a mottle is practically coextensive with the ramifications of the graphite, while the impoverished zone of metal corresponding to a given nodule is always larger, and usually much larger, than the approximately spherical mass of graphite crystals forming the nodules. Furthermore, the mottle probably is formed during freezing and the nodule almost always at a considerably lower temperature. Assuming that the nodules or mottles can be used as a measure of the existing nuclei (capable of germination) we propose to record certain observations as to the graphitizing reaction in the light of the number and habits of growth of these nuclei. The present authors, in cooperation with others1-7, have reported upon various cognate aspects of the problem. The fact that temper carbon is a mass of flakes and not a solid granule has become well recog-nized since the introduction of an improved polishing technique8,9,10 for cast iron. The problem of deriving from the circular planar intercepts

Jan 1, 1936

By F. J. Zuiderweg, G. G. Bemer

Results of a study aimed at assessing kinetics and mechanisms of the batch agglomeration process in suspension are discussed. A recently developed light backscatter technique which enables the increase of average particle size from 1 to 5000 µm to be followed, was used to determine agglomeration kinetics. Growth curves and agglomerate size distributions were obtained in a stirred vessel for various model systems and operating conditions. Four distinct growth regimes were identified, i. e. the flocculation regime, the zero-growth regime, the fast growth regime, and the equilibrium regime. Further, it was observed that large differences in the occurrence and duration of these regimes resulted from small variations in parameters, such as size distribution of the initial particles and the binding-liquid to solid ratio. Mechanisms that determine the occurrence of the relevant regimes are discussed. The growth process was described in terms of population balance equations. In this way, the growth rate, the equilibrium agglomerate size distribution, and the evolution of the agglomerate size distribution were generated. The agreement with experimental results is satisfactory.

Jan 1, 1980

By S. H. Moll, R. E. Ogilvie

The investigation of solid-state diffusion phenomena may lead to much information concerning binary alloys. In particular, a study of the concentration gradients present in multiphase diffusion couples can lead to the determination of the solubility limits of the single-phase fields in the phase diagram. The specific concentration gradient which results from the heat treatment of a diffusion couple depends not only upon the time and temperature of diffusion, but also upon the number of phases existing in equilibrium at the diffusion temperature. Such concentration gradients possess sharp discontinuities whose terminal points correspond to the solubilities existing at the limits of the two-phase field in the phase diagram at the diffusion temperature. In general, there will be a discontinuity in the concentration curve for each two-phase field which exists in the phase diagram between the concentration limits of the couple. A number of investigators have analyzed the gradients present in multiphase diffusion couples. 1-8 The iron-titanium phase diagram exhibits a y loop in the temperature range from 900" to 1400°C, and the limit of the a + y field lies at some composition which is less than 1 wt pct Ti for any temperature. It was felt that a diffusion study could yield values not only for the diffusion coefficients involved, but also for the chemical solubilities in the phase diagram. The concentration gradients were analyzed by an X-ray absorption technique developed by Ogilvie.6 The absorption of a monochromatic X-ray beam is measured in steps parallel to the diffusion direction and the resulting intensity gradients are transformed into concentration gradients by applying the laws of X-ray absorption in a binary system. This technique has been applied by ogilvie6 to the systems Ni-Au, Cu-Au, Fe-Cr, and Ni-Cr; by Gelles7 to the systems Be-Fe, and Be-Ni and by Hilliarde to the system Al-Zn. Linear X-Ray Absorption Analysis—The use of X-ray absorption analysis as a tool for determining concentration gradients arises from the fact that the beam is absorbed according to the quantity and species of elements present in the sample and not according to their state of aggregation. This method is more advantageous than the chemical analysis of machined layers since it is less time consuming and less expensive and can analyze a very small area. IF a homogeneous binary alloy (A + B) is analyzed with two different monochromatic X-ray beams I0(2) and lo(2) the following relation between the transmitted intensities, the intrinsic absorption coefficients of A and B for the two different radiations and the weight fraction of each element may be derived.' In (I/Io) (a+b) xa(u/p)a(2) + xb(u/p)8(2) Eq. [1] is independent of specimen thickness and density, but requires that either element A or B possess an absorption edge between the wavelength limits of the two monochromatic beams. I, is evaluated for each radiation by measuring the transmitted intensity through a varying number of foils of a suitable absorber. A plot of the natural logarithm of the transmitted intensity as a function of the number of foils, when extrapolated to zero foils, yields the value of I,. If a plot of the ratio in Eq. [ I] is calculated as a function of xA, then a master curve results. From

Jan 1, 1960

By R. V. Colligan

[CONTENTS PACE Educating and Training Economic Geologists of the Future. By C. H. BEHRE, JR. (TP 2278, Min. Tech., Nov. 1948. Discussions by R. V. COLLIGAN and EVAN JUST) ....... I Mercury Industry in Italy. By EDWIN B. ECKEL. (TP 2292, Min. Tech., Jan. 1948. Discussion .............................. by C. N. SCHUETTE) 3 Chert in the Kingsport Formation at Mascot, Tennessee. By ARTHUR T. ALLEN. (TP 2299, ............... Min. Tech., Jan. 1948. Discussion by M. M. BUTLER) 5 Wall Rock Alteration at Butte, Montana. By RENO H. SALES and CHARLES MEYER. (TP 2400, Min. Tech., May 1948. Djscussions by C. D. HULIN, W. D. JOHNSTON, JR., and L. C. ................................... GRATON) 5] Educating and Training Economic Geologists of the Future R. V. COLLIGAN*-I can best illustrate my opinions by drafting another five year plan (Table 2). This plan is set up following the same stipulations outlined by Dr. Behre, namely: (I) the student is preparing himself for commercial work as a mining geologist; (2) he is attending an institution with a sufficiently broad curriculum (that is, engineering school and mining school as well as liberal arts college) to furnish the courses listed; and (3) he is not planning to continue his studies through to a doctor's degree before going into commercial work. A comparison of my study plan (Table 2) and that submitted by Dr. Behre (Table I) will at once point up the basic similarity, due to the obvious fact that there are so many essential courses which must be included in any outline of study. However, a more detailed analysis will show up certain differences, which, in fact, are only certain refinements on Dr. Behre's program. These I plan to discuss in order of their importance. The first and most important change is the addition of 12 hr of optional subjects, making a total of 24 hr of optional subjects as against a total of 12 hr under Dr. Behre's schedule. This of course entails the elimination of certain courses, which I shall discuss later. However, I wish to make it clear that I suggest eliminating these courses not because I feel that they are unnecessary, but rather because I feel the optional courses are more necessary to the complete education of the individual. I appreciate that Dr. Behre recognizes the importance of the cultural side of education, but I take issue with his thesis that the student will get it without credit and in his spare time. I do not think that the average college student, and certainly not the college freshman, is mature enough to know what he needs and where to get it in his spare time. I think it must be "spoon-fed"; he must be oriented through specific courses. University life (or should I say "college life") is too full of athletics, fraternity activities, dances, "bull sessions," and countless other enjoyable distractions, all of which contribute to the "full man." I fail to see how the average young American male can possibly sandwich in a necessary complement of "cultural activities" in his spare time. Since these latter activities do not fall within the pattern set by the "group," and show less promise of immediate return in enjoyment, or increased social status on the campus, they are bound to suffer in competition with the more popular, "group" activities. No doubt much of the criticism levelled against arts colleges, namely, that the cultural courses are useless, is well taken, for the culture

Jan 1, 1947

By R. J. Robbins

"For his exceptional ability both as an engineer and entrepreneur in the conception, design, and marketing of underground boring equipment; a technological development which has greatly improved the efficiency and safety of underground mining." Recipient of the 1984 D.C. Jackling Award

Jan 1, 1985

By H. Cecil Spicer

THE results described in this article are based on field work conducted during the periods April-May, 1939, and May-July, 1940. The United States Potash Co. is mining potash on Government land under a permit from the Department of the Interior and the geophysical investigation was completed under a cooperative arrangement made between that company and the Conservation Branch of the Geological Survey. The writer, a member of the Section of Chemistry and Physics of the Geologic Branch, was assigned to this investigation. Four definite objectives were in mind for the geophysical work in the studies over the salt deposits. The first was to determine the measure of success that could be attained in this type of work with the resistivity methods that were to be employed. These methods had been introduced into the work of the Conservation Branch by Benjamin E. Jones for the investigation of dam sites, and have been used under his direction by the author for such work. If the method proved to be applicable, an effort was to be made to contour the top of the salt beds and also the other formation boundaries known to be present in this area. Salt-water aquifers were to be studied in an effort to determine their boundaries, and an attempt was to be made to delineate the potash-bearing beds. EARLIER STUDIES Others have made, and reported, resistivity studies over saliferous deposits in different areas. Friede1 and Messrs. Schlumberger2 reported geophysical work performed in the discovery of the salt domes of Alsace; Carrette and Kelly3 described the geology of the same area. Leonardon and Kelly4 published a resistivity curve obtained over the Hettenschlag dome, and a further discussion of this same area was given by the Messrs. Schlumberger5 in a communication. Messrs. Alty6 described studies on salt deposits in which the single-probe method was used. Sinerez7 mentions that electrical methods were tried over salt deposits in Spain. Geoffrey and Charrin8 show a resistivity curve obtained over marl, gypsiferous marl and salt which is similar to that obtained over the New Mexico salt deposits. Kelly9 reported resistivity work performed with the ground comparator of Zuschlag over the salt deposits near Syracuse, N. Y., where the Salina formation is at a depth of 700 to B00 ft. Some structural studies on the potash basin of Alsace are described by Poldini.10 Another single-probe resistivity study, made over salt deposits in New Mexico, is briefly described by Heiland,11 through the courtesy of Harry Aurand, of the Midwest Refining Co.

Jan 1, 1941

By Nicholas J. Grant, Noboru Komatsu

Metallographic and X-ray studies were made of oxide dispersion strengthened Cu-12 vol pet SiO2 and Cu-3.5 vol pet Al2O3 alloys following time exposures at temperatures approaching the melting. point of the matrix metal. Changes in hardness, oxide particle size and crystal structure were studied to determine the time-temperature stability of these alloys. An interpretation of the mechanism of oxide agglomeration is proposed. One of the most striking features of dispersion strengthened metal-metal oxide alloys is their stability at elevated temperatures, both with respect to recrystallization and maintenance of mechanical properties after exposure at high temperatures. A small amount of work has been done on the re-crystallization phenomenon in dispersion hardened metal-metal oxide alloys'l and several theoretical treatments have been advanced regarding the stability of these alloys by Lenel and Ansell,8 and by Grant and his co-workers.9, 10 This paper reports on metallographic and X-ray studies following various heat treatments of Cu-AI2D3 and Cu-SiO2 alloys at elevated temperatures and the effect of subsequent cold work on the recrystallizalion temperature. An interpretation of the recrystallization behavior of this type of alloy, based on the decomposition and agglomeration of oxides, is proposed. EXPERIMENTAL PROCEDURE Cast ingot bars of copper-1.59 pet Si and Cu-0.77 pet Al, 7/8 in in diam, were annealed in argon for 80 hr at 1000CC for homogenization. The homogenized rods were machined into fine chips and ball milled. Milled particles in the range minus 20 to plus 60 mesh were separated for internal oxidation. The internal oxidation was accomplished by the same method used by Preston and Grant,9 except that the oxidalion temperature for the Cu-Si alloy was 750°C, and for the Cu-A1 alloy was 800°C. These powders were then hydrogen-reduced at 450°C, compacted in a copper container, evacuated at room temperature to 0.04 µ, and sealed for extrusion. They were extruded at 1400°F (760°C) with a ram speed of 55 in. per min for an extrusion ratio of 15.6 to 1 to give a rod 0.38 in. diam by about 3 ft long.

Jan 1, 1962

By R. Van A. Norris

Although mechanical appliances for the ventilation of mines have been known siuce very early times (one being mentioned in Agricola's De Re Metnllica, 1657), it is only within the last forty years that such appliances have been generally used. A great number of different ventilators have been invented and used, but the varions forms of centrifugal machines having proved their efficiency, have now almost conlpletely replaced all others. Most if not all of the machines in use in this country are of this class, being either open-periphery fans, or closed, with chimney and spiral casing, of a more or less modified Guibal type. The theory of such machines has been demonstrated by Mr. Daniel Murgue in Theories and Practice of Centrifugal Ventilating Machines, translated by A. L. Steavenson. His statement may be condensed thus : Let a = orifice in a thin plate, of such area that its resistance to the passage of a given quantity of air equals the resist ance of the mine. I o = orifice in a thin plate of such area that its resistance to the passage of' a given quantity of air equals that of the machine. Q = quantity of air passing in cubic feet per minute. V = velocity of air passing through a. Vo = velocity of air passing through o. h = head iu feet air-column to produce velocity IT h, = head in feet air-column to produce velocity V,.

Jan 1, 1892