Search Documents

By JAMES J. PURDY

The great majority of stokers used in residential heating installations are of the clinkering type. Because of inherent characteristics of the under- feed combustion process as it occurs in these small stokers, and because of the wide range of operating conditions encountered in residential heating schedules, not all bituminous coals can be used successfully in residential underfeed units. The problem of providing consumer satisfaction has been attacked by the joint efforts of the stoker manufacturers and the coal industry; the stoker manufacturers have been concerned with improving their product to permit the use of a wider range of coals, and coal operators have made every effort to market selected and better prepared coals. In view of the wide range of physical characteristics and chemical properties of bituminous coals, the problems are real and are receiving increased attention.

Jan 1, 1949

Tumbling mills and some theoretical and practical aspects of milling are discussed. Attention is directed towards the difficulty of relating the dynamical analyses of the motions of particles within mills to the existing treatments of breakage processes. This synthesis may be advanced by a study of milling that utilizes the matrix analysis of breakage processes. Application of the matrix analysis to results obtained on (i) grinding in open-circuit a zinc ore in a conical pebble mill and in a modified conical mill, (ii) "grinding of cement clinker in a compound mill, and (iii) to some drop-weight grindability tests is discussed. It is shown that the 'IT-breakage model adequately describes the breakage processes of each of the tests. (The proportion broken in each breakage cycle is given by 'IT and is independent of particle size.)The size distributions of the products are accurately predicted in the cases considered. Matrix analyses of the breakage of coals, various ores and a cement clinker have been made. Appendices give an elementary account of the matrix methods and give the equations fully describing reverse order closed circuit operations. The matrix analyses of breakage processes and the survey are used to examine briefly closed circuit grinding.INTRODUCTIONTumbling mills are slow-speed crushing and grinding machines which have been developed from some fairly simple types into many widely differing forms. Many of these versatile mills have proved extremely useful in ore dressing and mineral beneficiation, whereas others have been used in the cement industry and less extensively in the coal industry.The performance of even the simplest tumbling mill is very imperfectly understood, whilst the more difficult problems associated with the balancing of complex milling circuits and with the establishment of the optimum operating conditions for the whole of a complex circuit are even less well apprehended.Our knowledge of the performance of tumbling mills is rather sharply divided into two categories: the first consists...

Jan 1, 1957

By R. A. Harris

In this study Pt-Al thin films were prepared via electron beam physical vapour deposition (EB-PVD) with an atomic concentration ratio of Pt25:Al75. These films were heat treated at temperatures ranging from 150°C to 650°C for annealing times from 4 to 60 minutes. The resulting microstructure of these thin films were obtained via secondary electron imaging used in conjunction with depth profiling with the aid of scanning auger microscopy (PHI 700).Elemental maps of the micrographs were obtained. Simulations, based on a chemical potential Monte Carlo method1, were run for various interaction parameters. From these simulations theoretical depth-profiles and proposed microstructures were obtained. These were compared to the experimentally measured depth profiles and elemental maps. Keywords Monte Carlo, chemical potential, depth profile, Pt-Al thin films.

Jan 1, 2011

The oxidation of ferrous sulphate to ferric sulphate with air and oxygen in a gas lift percolator was investigated with initial Fe2+ concentrations in the range 0·01 M to 1·0 M,temperatures in the range 20-80°C, and pH in the range oto 2.The rate of formation of Fe3+ was found to be well described by the rate expressionEquation 1and a consistent mechanism is proposed.The presence of Cu2+ was found to cause an increased rate of oxidation, the effect being greater with Cu2+ concentrations increasing in the range 0·001 M - 0·01 M in 0·2 M Fe2+. The effect of other solutes containing Ni, Zn, Mn, Co, Hg, Cl, Mo, NH4, As, Cr, or Na at a concentration of 0·001 M in 0·2 M Fe2+ was negligible.

Jan 1, 1972

By E Topal

Stopes are used in several underground mining methods. Boundary determination of these stopes is generally based on simple rules of thumb. While several stope boundary optimisation techniques are available, they fail to guarantee true optimum results. The first part of this paper reviews some important stope boundary optimisation studies and proposes a new algorithm to optimise stope boundaries and layouts for underground operations. The second part applies the proposed algorithm to a block model to test its ability to produce optimum results and demonstrate its applicability in a number of different scenarios. The results demonstrate that the proposed algorithm can find optimum stope boundaries and layouts in three dimensions for different stope sizes and economic conditions.

Jan 1, 2009

A New Cell for Electrochemically Aided Flotation

Sep 13, 2010

By R. Karl Zipf

Highwall mining is an important surface coal mining method, and it may account for approximately 4% of total U.S. coal production. Highwall stability is the major ground control related safety concern. Ground control plans for highwall mining should specify hole width, web pillar width, barrier pillar width and number of holes between barriers. This paper offers simple design charts for these parameters aimed at providing “ball park” checks. Web pillars containing pre-existing auger holes are analyzed and a design chart for estimating their minimum width is also presented. Finally, close proximity multiple seam highwall mining, which may have caused several serious highwall failures, is analyzed. Web and barrier pillar recommendations for this special situation are presented.

Jan 1, 2005

The mining industry is generally regarded as a high risk industry, mainly because of the difficulties in estimating the tonnage and grade of mineral resources, the fluctuations in metal prices, mining problems and other problems which occur with mining in offshore and remote locations, such as appropriation or disruption to supply. As a consequence, finance providers require a high reward from mining projects. In the past two decades, the development of "mega" projects has led to the packaging of the finance becoming more sophisticated. Some would see this move as a measure of the evolution of banking rather than an intrinsic facet of mining finance itself. Project financial managers now require a thorough knowledge of all the financial tools which are available and have to be aware of the funding options so that they can put together a finance package which minimises the cost of the financing with the risk spread adequately between the partners of the financing. The different sources and types of finance for mining projects are described herein along with the factors which determine their costs. To understand the ramifications of financing mining projects, it is essential to appreciate the fundamental difference between debt and equity, which illustrates the importance of gearing. Costs of finance are determined by the interaction of supply and demand forces. Bankers and other financiers have become more adept at isolating a wide selection of risk elements and have devised a formidable range of insurance mechanisms. There is still a lot of money looking for good project risks and if a good project is properly presented and structured, financing can be obtained in today's market.

Jan 1, 1990

By A. Tylczak, C. Norman, C. Shook, S. Loif

"There are a lot of good reasons to manage energy use at mining operations. Optimizing process energy use reduces operating costs. Tracking energy use can help identify unplanned process changes or malfunctioning equipment early, which allows problems to be corrected promptly.Sacré-Davey Engineering in Vancouver has performed over 50 Energy Management studies for various industries including: mining, pulp and paper, oil and gas, etc. Energy Management programs can be used to identify energy reduction opportunities, assess project feasibility, complete equipment selection trade-offs, as well as to monitor and manage energy costs. Benefits of energy management programs are reduced energy costs, reduced maintenance, and increased plant automation. Additionally, energy management can provide access to utility incentive funding and quantify savings which can greatly improve the return on investment of potential projects.Energy management studies are funded by many Utility programs across Canada. There are various programs available for existing plants energy audits, project feasibility studies, new plant design reviews and energy monitoring and targeting, etc. There are capital incentives available which can significantly reduce payback period.This paper discusses how energy management can be used to support mill/mine operations groups, maintenance programs, as well as expansion or green field projects. This paper will also provide an overview of Canadian Utility companies programs and how they can assist mining companies.IntroductionThere are a lot of good reasons to manage energy use at mining operations. Optimizing process energy use reduces operating costs. Tracking energy use can help identify unplanned process changes and identify malfunctioning equipment early, which allows problems to be corrected promptly."

Jan 1, 2015

By Lyman C. Hitchcock

The objective of this program was to determine the minimum luminance requirements for underground coal mining work from the working face to the first transfer point. The resulting data encompasses 114 visual tasks from conventional continuous and longwall mining methods representing the salient visual tasks found in the jobs listed. Cutter Operator Roof Bolter Face Drill Operator Airdox Operator Longwall Jackman Shuttle Car Operator Loader Operator Shot Fireman Continuous Miner Operator Longwall Head Conveyor Operator Longwall Tail Conveyor Operator

Jan 1, 1973

The purpose of this paper is to describe briefly the clean-up procedure adopted at the treatment plant of Paringa Mining & Exploration Co. Ltd. at Kalgoorlie, Western Australia.A clean-up is carried out at the end of each four-weekly period, and all figures subsequently quoted are taken from a summary of the results of the eight periods ending 8th April, 1941.STRAKING AND AMALGAMATIONOf the total gold won 22· 77 per cent. is recovered by straking and amalgamation.The discharges of both the primary and secondary ball mills are pumped over a common set of five ten feet long by three feet wide straking tables, set at an angle of 10 degrees, before passing to the 14 ft. diameter by 30 ft. by 8 ft. Dorr bowl classifier.This classifier is in closed circuit with both of the ball mills, hence the whole of the circulating load of the fine grinding circuit, which approximates to 800 per cent., is required to pass over the straking tables. For convenience in handling, corduroy cloths are used in lengths of 5 feet, and are picked up and replaced by clean cloths at four-hourly intervals. The avaHable straking area provided is, therefore, 900 square feet, or approximately 3·30 square feet per original ton per 24 hours. The density of the pulp passing over the tables is about 54 per cent. solids, the area provided per ton of pulp per 24 hours being approximately o· 2() square feet. Washing of the corduroy cloths is carried out on the day shift only, about 800 lb. of strake concentrate being obtained daily.This concentrate is sluiced from the washing trough on the elevated straking floor to the 4 ft. by 2 ft. diameter amalgamating barrel located in the gold room below.The barrel is of standard design and is rotated at 25 r.p.m. It is charged each day at 4 p.m., and grinding of the strake concentrate at approximately 70 per cent. solids is continued until 8 a.m. the following day. The barrel is then stopped, and the contents generously diluted with water, and after a few minutes rotation some of the slime is carefully poured off through the small discharge hole. This dilution and decantation is repeated until a good deal of the valueless slime has been removed.A further quantity of strake concentrate is then charged to the barrel, which is allowed a further 16 hours grinding period. After again diluting and decanting, approximately 25 lb. of mercury and 15 lb. of lime are added to the charge, which is then given an amalgamation period of 2 hours before cleaning up.By the process of grinding, diluting and removal of slime by decanting...

Jan 1, 1941

By A. Davis, C. Webb, J. Sorensen

The abandoned Belle Eldridge Mine near Deadwood, South Dakota, is on land controlled by the U.S. Bureau of Land Management (BLM). The mine produced lead and zinc during the first half of the 1900s. Because of acidic drainage and elevated levels of metals in tailings and waste rock, the site was evaluated in 1998 and 1999. After evaluation, the mine was remediated during 1999-2001 by the BLM. Since remediation, values of pH in water samples have been nearly neutral and specific conductance values have been much lower than before remediation. The Grizzly Gulch forest fire of July, 2002, consumed much of the Belle Eldridge site and resulted in greater than normal erosion and sediment flushing during the months following the wildfire. Had the site not been remediated and the tailings emplaced within a capped repository, generation of acidity and off-site migration of heavy metals within sediments could have been severe at downstream locations.

Jan 1, 2007

By Robert S. Hedin

Passive methods of treating mine water use chemical and biological processes that decrease metal concentrations and neutralize acidity. Compared with conventional chemical treatment, passive methods generally require more land area, but use less costly reagents and require less operational attention and maintenance. Currently, three types of passive technologies exist: aerobic wetlands, organic substrate wetlands, and anoxic limestone drains. Aerobic wetlands promote mixed oxidation and hydrolysis reactions, and are most effective when the raw mine water is net alkaline. Organic substrate wetlands promote anaerobic bacterial activity that results in the precipitation of metal sulfides and the generation of bicarbonate alkalinity. Anoxic limestone drains generate bicarbonate alkalinity and can be useful for the pretreatment of mine water before it flows into a wetland. Rates of metal and acidity removal for passive systems have been developed empirically by the U.S. Bureau of Mines. Aerobic wetlands remove Fe and Mn from alkaline water at rates of 10-20 and 0.5- 1.0 g. m-2? d-1, respectively. Wetlands with a composted organic substrate remove acidity from mine water at rates of 3-9 g. m-2? d-1?. A model for the design and sizing of passive treatment systems is presented in this report.

Jan 1, 1994

Exploring the Breakage Environment in Mills with Discrete Element Methods

Sep 13, 2010

Electro-Flotation Research on Fine Cassiterite

Sep 13, 2010

By Lino Arias

The main objective of this project is to review and develop a comprehensive application of Lane’s cut-off grade model to a case study, as well as to compare its principles and results compared to break-even cut-off grade model utilisation under the same conditions. The case study sets the context of the application: A conceptual study of a gold open pit mining project requires a cut-off grade analysis, which consists in develop a cut-off grade policy that maximises the net present value (NPV) using Lane’s and break-even model.

Sep 1, 2017

Test Work on High Throughput Diamond Tracer Recovery from Alluvial Recovery Tailings with a Containerised Optical Sorter Under Real Production Conditions Worldwide alluvial diamond deposits are traditionally processed with dense media separation and XRF sorters, hand picking or grease tables. The test work conducted verifies the performance of an optical sorter detecting the transparency of particles for diamond recovery from the DMS concentrate, eg XRF-sorter and handpicking tailings. The containerised setup enables economically feasible, high throughput, semi-mobile setups to retreat recovery tailings from alluvial and also primary deposits. The test work has been conducted with quartz and glass particles, which are less transparent or comparably transparent, under realistic production conditions on a 600 mm belt machine with an installed electrical power of only 21 kW. The results show that 99 per cent recovery can be reached at a throughput of 10 t/h in the -8 + 2 mm fraction and at 22 t/h in the -25 + 8 mm fraction. At a throughput of 18 t/h a recovery of 88 per cent has been assessed. At a further escalation of the throughput, dust in the sorter container made sorting impossible in the coarse fraction and the recovery decreased significantly in the fine fraction. Analysis of the belt coverage indicates that higher throughputs of the coarse fraction can be fed onto the optical sorter if the dust extraction system is improved. The results are basis for the decision to conservatively feed 20 t/h of the coarse fraction and 17 t/h of the fine fraction in day to day production. The settings have been applied to sort alluvial recovery tailings in South Africa and will be applied to sort the recovery tailings of a primary deposit in Lesotho. The test work has shown that an optical sorter can be used to retreat recovery tailings with high throughputs. The compact setup of a screen and a 9 m standard container enables semi-mobile, temporary setups for small recovery tailings dumps and remote areas. In addition, sorting on transparency ensures the recovery of high value low-fluorescent diamonds.

Sep 13, 2010

By S. Frimpong

The cable shovel excavator is used for primary production in many surface mining operations. A major problem in shovel excavation is the variability of material diggability, resulting in varying mechanical energy input and stress loading of shovel dipper-and-tooth assembly across the working bench. This variability has a huge impact on the shovel dipper and tooth assembly in hard formations. In addition, the geometrical constraints within the working environment impose production limitations resulting in low production efficiency and high operating costs. A potential solution to the above problems is the application of an intelligent cable shovel excavation(ICSE) technology. In this paper, dynamic models of the cable shovel excavator are developed with numerical examples. These models form the basis for developing dynamic shovel simulators for an intelligent shovel excavation technology. The dynamic equations are developed using the Newton-Euler techniques. The path trajectories for efficient excavation, dynamic velocity and acceleration profiles, and dimensioned parameters for optimum feed force, torques and momentum of shovel boom-bucket assembly are modeled and used for efficient excavation. The optimum digging forces and resistances for the cable shovel excavator are modeled and used to predict optimum excavation performance.

Jan 1, 2003

By R. M. Whyte

The Konkola Deep Mining Project (KDMP) seeks to exploit the deep level potential of the Konkola Deeps orebody, producing high grade copper concentrates for treatment at the Nkana Smelter and Refinery. As an alternative to smelting, Konkola Copper Mines (KCM) has examined a processing route involving pressure leaching of the Konkola concentrates at Nchanga, with the leach liquor being treated by solvent extraction and electrowinning to produce high purity copper cathode. The solvent extraction circuit would be operated to achieve a high ?delta? copper, thereby providing a strong acid raffinate which can be used in the existing Tailings Leach Plant (TLP) to treat Nchanga oxide copper materials. The main focus of the hydrometallurgical option is to capitalize upon the synergy that exists between the treatment of sulphide copper concentrates (acid producing) and oxide copper ores (acid consuming). The paper discusses the key features of a comprehensive piloting campaign carried out at Anglo American Research Laboratories, which involved the co-treatment of Konkola copper concentrates and Chingola refractory ore in a fully integrated pilot plant circuit.

Jan 1, 2001

By Manoj Khandelwal, Bright Akuinor Tsidi, Newton Amegbey, Daniel Mireku‑Gyimah

One of the ambient effects of production blasting is flyrock. To effectively manage flyrock throw distance in mining, there is the necessity to successfully envisage blasting output without sacrificing the hazardous impact of flyrock which may result in fatality and operational shutdown. For flyrock throw distance prediction, velocity of detonation (VOD) and charge per bank cubic meter (CPBCM) are not usually included. This paper focuses on the use of support vector machine (SVM) regression to ascertain the impact of VOD and CPBCM on flyrock throw predictions. The machine learning models were linear support vector machine (LSVM), quadratic Gaussian support vector machine (QGSVM), fine Gaussian support vector machine (FGSVM), medium Gaussian support vector machine (MGSVM), and cubic Gaussian support vector machine (CGSVM). The outcome indicates that FGSVM was the most sensitive with a 4% improvement when VOD and CPBCM were included. As a result, the LSVM model provides a suitable AI competitive alternative tool for flyrock throw prediction in mining operations by incorporating VOD and CPBCM.

Feb 10, 2024