Search Documents

By Mingju Liu

In this research, we measured fractal characteristics of over ten typical outburst areas on different scales and related them to their outburst proneness, in attempts to provide new methods for outburst prediction. It was shown that both faults and folds follow the power law on coal basin scale, mine scale or mining district scale, whichever it is. Fractal dimensions are appropriate indices to describe geological structures quantitatively. Preliminary relationships have been established between outburst proneness and fractal dimension. Comparisons have been made among fractal characteristics and degrees of outburst proneness on all three scales. The results indicate that multi-scale assessment of outburst proneness can be made based on fractal measurements independently or supplemented by other assessment methods.

Jan 1, 2000

By Kent D. Mctyer

Mining commenced at Tasman Mine in late 2006. The current method of mining is bord and pillar using continuous minerbolters and shuttle cars for first workings and secondary extraction using mobile roof supports. The two stage process was chosen to accommodate irregularly shaped coal deposits, allowing adjustments to be made to extraction ratios for better management of subsidence and to maximize the efficiency of the operation. Following the completion of the first three full/partial extraction panels, the mining method was changed due to variable caving. Another partial extraction method, referred to as the Duncan Method was adopted; it involves stripping the developed square pillars on four-sides on retreat to leave a load-bearing remnant coal pillar. The system of partial extraction has been successful in meeting safety, productivity, and subsidence targets.

Jan 1, 2011

By Christopher Mark

The demographics and safety record of the pillar retreat segment of the U.S. coal industry was analyzed using statistics collected by the Mine Safety and Health Administration. Pillar recovery is practiced primarily by mines in Appalachia and the Midwest. Using 1993 data, the accident rates and productivity of a large sample of pillar re- mines were found to be similar to other room-and-pillar mines in the same geographic areas. Pillar recovery apparently accounts for about 10% of all U.S. underground production, but has been associated with about 25% of the mf and rib fatalities during 1989-96. However, of the 28 fatalities that were analyzed, only 4 occurred for which no citations were issued for violations of mining law. Nearly one- half of the fatal incidents occurred during the mining of the last lift or pushout. All four no-citation incidents occurred during the removal of the last lift during a "Christmas tree" extraction sequence.

Jan 1, 1997

By David B. Plumeau

The Cayuga Mine, a deep rock salt mining, operation, changed from a standard room and pillar mine design to a yielding pillar/pressure arch design five years ago. In general the roof conditions improved. However, entries adjacent to the abutment pillars continued to fail. It was noticed that where abutment pillars were accidentally "notched" (by driving cross- cuts one cut into the pillars), the abutment entries had better roof conditions than where there were no "notches". Experiments with intentionally notched abutment pillars showed that notching did improve abutment entry conditions. During the past four years notch configuration has been varied to suit local ground conditions. Recently, "pre-cutting" of notches has proven itself as a means of protecting abutment entries under severe ground conditions. As an added bonus, the notches improve productivity by providing more places to work and reduce costs because it is not necessary to bolt the notches.

Jan 1, 1981

By S. P. Singh

Destress blasting is commonly used in the mines to minimize the occurrence of rockbursts. The fracturing created by destressing in the vicinity of the face reduces the stress concentration by pushing the zone of high stress deeper into the rock mass. But the destressing practice by blasting may be devastating near the faults or other sensitive high stress zones. To avoid severe rockbursts in such situations, the application of chemical destressing has been proposed in this paper. A laboratory investigation was conducted on the rocks in the Sudbury basin to examine the change in the material properties with an aim of assessing the feasibility of destressing by chemical means. The favourable change observed in the rock properties led to the suggestion that the injection of surfactants in boreholes would enhance fracture propagation similar to what is currently done by blasting but in a safer, inexpensive and non-violent manner. The current destressing practices in Ontario mines have also been reviewed in this paper.

Jan 1, 1987

By Jennifer Riefenberg

Underground coal mines often experience ground control problems related to weak floor. Developing a methodology for rating floor quality can aid in understanding and delineating ground hazards. U.S. Bureau of Mines researchers are currently exploring methods for generating ground control hazard potential maps. One component of hazard potential in floor-heave-prone mines is delineating floor quality and its correlation with failure. Although field exposures are limited, significant information on the roof and floor quality can be gained through analysis of existing drill core data. Drill core data and roof and floor exposures were analyzed for quality. Laboratory tests were run on 50 core samples to evaluate, compressive and tensile strengths of various roof and floor lithologies. Extensive geologic and lithologic examinations of the cores and samples were also completed. Results of this work involve the formation of a preliminary quality rating for coal mine floor using a modified Coal Mime Roof Rating (CMRR).

Jan 1, 1995

By Kenny D. Basnett

An analysis of the Roof Falls Data Base (RFDB) for underground coal mines in Illinois for the period 2004?2008 indicated that about 80% of the roof falls occur at intersections and are associated with geologic anomalies or a rapidly changing geologic environment. Most falls are associated with anomalies such as clay dikes, differential compaction faults, shear zones, joints and fractures, and geologic structure. Therefore, a better analysis of the geology with emphasis on mapping anomalies such as joints and fractures and their application is necessary to improve ground conditions and safety. Such studies within Illinois Coal Basin are limited. This paper presents a mapping study of the joint orientations with documentation of dip of the several lithological units that lie directly above the Herrin No. 6 Coal seam around southern Illinois. These units include the Energy Shale, Anna Shale, and Brereton Limestone. The mapping was done in three mines and the data were plotted on a stereographic projection to determine the average characteristics of joint planes. The study mines included two deep underground mines and one shallow highwall mine. This study has helped identify favorable mining and support orientations in areas of highly variable geology. These are currently under review by the cooperating coal company for experimental roof control studies.

Jan 1, 2011

By Khaled Morsy

Most of the available numerical codes simulating the reinforcing effect of fully grouted bolt are accomplished by a series of bar elements which are connected along their length to the host rock by shear springs and sliders. The spring-slider system represents the shear bonding effect between the bolt and the host rock. This paper describes a three dimensional finite element modeling technique for the 3D simulation of fully grouted bolt reinforcement. The proposed technique introduced a physical simulation for the fully grouted bolts. The bolt simulation is composed of a series of beam elements (representing the steel rebar) embedded in brick elements (representing the grout). Because of the complexity of the grout/rock interface, ABAQUS explicit code was used. A modification of the ABAQUS default friction model was conducted to consider the cohesion of the grout/rock interface. The interaction between the grout and the host rock is simulated by the modified friction model. To verify the proposed technique, a simulation of the pull out test we conducted. The results from the simulation were compared with former studies

Jan 1, 2004

By S. Y. Liu

Based on the underground measurements, physical model test of simulated materials in the laboratory and finite element analysis, this paper demonstrates the pattern and process of roof fall over the tip-to-face area in the fully mechanized coalfaces. The main factors that affect the stability of the immediate roof are thoroughly studied including the fracture position and tilt angle of the main roof, the tensile strength (Rt) and cohesive force (c) of the immediate roof, and type and resistance of the powered support. Based on these factors, this paper proposes the basic process of immediate roof breakage a. follows: As the longwall farm advances, the main roof breaks and then rotates. A tensile fracture zone will be formed in the immediate roof under the fracture line of the main roof. A caving zone (plastic zone) will be formed in unsupported area between coalface and canopy tip. If these two zones overlap the immediate roof will be completely unstable. Under this condition, powered support will have difficulties lo control the rod. Therefore it is necessary to study the process of immediate roof breakage and look for effective methods for controlling the roof.

Jan 1, 1990

By Deren Zhu

The principle of roof control in longwall mining is to control main roof fractures so as to reduce roof weighting, plus reasonable and effective design of supports to reduce the convergence and premature caving of the immediate roof. This paper introduces a comprehensive test for better roof control based on the geological conditions of coal seam No. 16 in Zaozhuan Colliery, China.

Jan 1, 1990

By Ross W. Seedsman

The feasibility of 6 m high single pass longwalling has been studied using Newlands Mine as a case study An intensive geological investigation identified a range of hazards but a mine layout was possible that minimised the risks with respect to joints, cleats, angular bedding, coal shears and horizontal stress. Geotechnical design input was required for support capacity, subsidence, gate to face transition, face span, and roof support. It is concluded that longwall face equipment can be made available by modifying existing designs, gate to face transitions will require a number of steps, and a mid-face sprag should not be required for routine operations.

Jan 1, 1992

By Gregory Hinshaw

Underground mine bolting machines have evolved since inception in the 1940's due to the need for increased safety and productivity. However, major design innovations historically came from changes in the mining plan and the mine environment. During the last ten years, productivity needs have outpaced the evolution of existing designs. J. H. Fletcher & Co. has responded with a commitment to research and development which has fostered several new designs. The most recent machine built is a walk through crawler frame powering four drilling units simultaneously with semiautomatic computer control using two operators. This machine utilizes technology to create a safer yet more productive roofbolter for continuous mining sections utilizing place changing methods.

Jan 1, 1998

By W. J. Guo

Overburden movement as a result of longwall mining can be classified into, in ascending order, caving zone, fractured zone, and bending zone. Operation experience and laboratory research have demonstrated that there are bed separations in the bending zone due to differential movement and rock mechanics properties between adjacent strata. In china several coal mines have injected flyash into bed separations to prevent strata movement and control surface subsidence. This method is very effective because it can reduce surface subsidence by 35-55%. Combining the field survey results and laboratory simulation research, the author has investigated bed separation and its mechanisms and effect of backfilling the bed separation and its mechanisms. Finally backfilling application in three mines are introduced, including grout flow chart, grouting pressure, and radius.

Jan 1, 1994

By Quanzhong Gu

Stability of a pre-exnacted recovery room plays a vital role when longwall face approaches and during a longwall face move. In an attempt to extend the application of pumpable cribs into recovery room support and to limit roof bolt installation when a longwall face approaches the recovery room, yieldable and cuttable pumpable cribs (YCPC) were employed in the recovery room at the northern West Virginia mine. The YCPC consists of two layers of materials with different strengths. This allows considerable deformation from the floor and/or roof by sacrificing the soft layer while maintaining relatively high load capacity under mining¬induced front abutment loads. The thickness and stiffness of the soft layer, installation and quality control are the key factors when using the Yieldable and Cuttable Pumpable Crib to stabilize longwall recovery room- Underground observation and monitoring results show that the Yieldable and Cuttable Pumpable Crib is a viable solution to insure stability of the recovery room and can save at least two days for a longwall face move at the mine.

Jan 1, 2004

The applicability of four empirical strength criteria for rock masses, namely, Hoek and Brown, Bieniawski - Yudhbir et al., Rarnamurthy - Arora and Johnston - Sheorey et al. has been tested against the triaxial test data for jointed plaster of Paris of Arora. The following modified Bieniawski criterion shows best agreement with the triaxial test data for jointed plaster of Paris:- where st = axial compressive stress at failure, MPa; s3 = confining pressure, MPa; scm = uniaxial compressive strength of jointed plaster of Paris, MPa; and B = - 3.988 + 9.674 (scm )-0? 185 The modified Bieniawski strength criterion can be used to estimate the strength of a coal pillar, based on a knowledge of stress distribution in it.

Jan 1, 1992

By Yingda Zhai

The range of interburden thickness between coal seams in Datong Mining District of China is large. From mining operation point of view, the closer is between the two seams, the greater is the impact from the upper seam when the lower seam is mined. This impact is most notable when the two seams are ultra-close. In this paper the definition of ultra-close seams and its practical method of determination are presented. Based on the difference in strata thickness in the interburden and the concept of "yield depth ratio" which is defined as the yield zone depth in the interburden to the total thickness of interburden, the roofs of the ultra-close multiple seams in the Datong District of China were divided into 3 types: (1) false roof or rock partings in coal seam. This type of roof does not require special handling except mining them simultaneously as one single seam. The roof thickness is slightly less than 0.5 m; (2) completely broken roof. In this type of roof, the yield depth ratio is larger than (or equal to) 1. When the roof thickness is larger than 0.5 m but less than 2.0 m, the yield depth ratio must be smaller than 1; and (3) fractured roof. In this type of roof, the yield depth ratio is less than 1 while the roof thickness is larger than 2.0 m. In retreat longwall mining, if the gateroads of the lower seam are located under the gob of upper seam, roof bolting can be used in the 3rd type of roof. But if the 2nd type roof exists, powered supports must be used.

Jan 1, 2005

By Zach G. Agioutantis

The prediction of ground movements due to underground mining using the influence function method is a mature technology, widely used by researchers and planning engineers around the world. Surface strain, either tensile or compressive, is an important indicator of potential impacts on structures such as buildings, bodies of water, pipelines, railway and power lines, and tailings dams. Calculation of static or dynamic surface strains, for varying surface terrains and slopes, should be accurately predicted and be independent of the methodology applied for the calculation. This paper discusses and compares the development of horizontal and ground strains on the surface due to underground mining for different surface topologies (sloping terrain, monitoring lines, etc.) and presents the steps needed to ensure accurate calculations. Examples are given to demonstrate how ground strains can be calculated for one- and two-dimensional gridded surfaces.

Jan 1, 2013

By Ben Fahrman

The classical approach to engineering design involves the purely deterministic calculation of the factor of safety, the ratio of strength to stress. The factor of safety is an easy calculation to perform in many circumstances, and it is very easy to interpret the results. The simplicity of the method is both a strength and a weakness. The results of the deterministic factor of safety calculation are simple to determine and interpret, but they have no ability to account for the uncertainty present in the inputs or outputs. Uncertainty is prevalent in geotechnical engineering applications. This uncertainty can stem from spatial variability, poor sampling, a dynamically changing environment, etc. Probability analyses allow input parameters to take the form of a distribution rather than a single value, making them uniquely equipped to handle the uncertainty inherent in geotechnical engineering design considerations. A stochastic approach also has the benefit of providing results as a probability of failure, which is more meaningful than a factor of safety. Though stochastic modeling is becoming more common in many geotechnical applications, it is still not widely used for coal pillar design. The objectives of this study are to justify the concept of using a stochastic approach to coal pillar design and to compare the results of a simple stochastic analysis to those of standard industry practice. A simple synthetic study was performed to compare the results of a probabilistic analysis of coal pillar design to the results obtained from running ARMPS, which is published by NIOSH. Normal distributions were assigned to each input parameter that is required to determine the factor of safety of a single coal pillar. The probability of failure resulting from the synthetic study was found to be more conservative than the ARMPS stability factor. A probabilistic approach to coal pillar design is discussed in comparison to the traditional deterministic approach. The greatest strengths of the probabilistic approach were determined to be the effective handling of uncertainty and the increased meaning of the inputs and outputs inherent to a probabilistic approach.

Jan 1, 2013

By Behdeen Oraee-Mirzamani

Tunnel stability has an important role in the production process of an underground coal mine. There are various methods for analysing tunnel stability, such as numerical methods and analytical methods. In this paper, numerical methods (Phase2 software) have been used to determine tunnel wall displacement in a mining tunnel of the Parvade underground coal mine. The Ground Reaction Curve has also been drawn using analytical methods to determine tunnel wall displacement. The comparison of results from the numerical method and the analytical method show a noteworthy difference in the tunnel wall displacement. The displacement calculated by the numerical method shows a lower value than that of the analytical method because the numerical method is more suited to modeling the various coal and rock layers, as well as the shape of the excavations found in coal mines. The methodology used in this paper together with the results obtained from both methods can serve as useful tools for the coal mine design engineer when determining the ground support requirements.

Jan 1, 2013

By A. Wilkinson

An investigation into the performance of support systems that are currently used in South African coal mines was conducted. Five most critical components of a support system have been identified. These components are resin, bolt, hole, machinery/equipment and the rock type. All five of these components are equally important as failure in any of these components will result in an inadequate support system. The performance of resin used in South Africa was investigated through in situ short encapsulated pull tests. The results indicated that in the majority of pull tests, failure took place at the rock-resin interface, indicating that the rock failed before the resin shear strength had been reached. It is therefore concluded that the strength of resin currently used in South Africa is adequate. It is found that although the maximum bond strengths achieved form both resin suppliers were similar, there was a considerable difference in the stiffhess of the resins. Roof bolt diameters and rib heights of bolts from three major manufacturers were evaluated (approximately 80 roof bolts from each manufacturer). The results showed there is a significant variation in bolt diameters and rib heights in the same batch in roof bolts supplied by certain manufacturers. The results also showed that on average there are insignificant differences between the parameters that determine the bolt profile (rib angle, spacing between the ribs and rib thickness). The influence of these parameters on bolt performance was very small and could not be established in situ. Roof bolts from four major suppliers were also evaluated through in situ short encapsulated pull tests. The results showed that the reinforcing system using roof bolts from all four manufacturers performed almost identically in sandstone, but somewhat differently in other rock types. The effect of bit types was evaluated. Both the stresses and the maximum loads obtained from the two-prong bits were greater than those obtained from a spade bit. Borehole annulus was found to be another important parameter that determined the support performance, and was investigated. The results from these tests showed that an annulus between 2.8 mm 4.5 mm resulted in the highest bond strengths. The results also showed that as the annulus drops below 2 mm, it appears to have a negative effect on the bond strength. The effect of wet and dry drilling on support performance was investigated. The results showed that wet drilling can-provide relatively greater system stiffnesses and slightly greater bond strengths. Short encapsulated pull test results showed very distinct differences between bolt system performance in different rock types and that sandstone produces significantly better results than shale and coal. From the results it is concluded that rock type is probably the primary factor influencing support system performance. A detailed investigation into the specifications of roofbolters that are currently being used indicated that the quality of installation of a support system is directly related to the performance of the equipment that is used to install the bolts. The important parameters, torque, thrust and speed of bolting equipment were investigated. The results showed that there are significant variations in these parameters in South African roofbolters.

Jan 1, 2005