Search Documents

By P. G. Irwin

Natural resins, those derived from coal and those mined in the Uintah basin, face challenges from synthetic resins that are derived from petroleum sources and rosin or wood sources. In the past, fossil resins from coal were produced by various companies, the last one being Hercules, Inc., which sold BLACKHAWK resin until a fire destroyed the plant in the mid 1970's. Approximately four to fjve million pounds of BLACKHAWK were produced and sold mostly to the printing ink industry. Uintaite, more commonly known as Gilsonite® resin, was widely used by various industries, notably in printing inks, coatings, stains, adhesives, foundry, asphalt paving, and oil well drilling muds. Gilsonite has lost market share over the last thirty years to various synthetic resins particularly hydrocarbon resins that are derived from petroleum sources.

Jan 1, 1990

The public relations problems of users of explosives have greatly increased within the past few years. One reason is that explosives and blasting agents are being consumed in increasing quantities. The principal reason, however, is that more people have become physically affected by blasting. Mines, quarries, and construction sites that were formerly in relatively remote locations now find themselves near congested areas. New express traffic ways being constructed to connect the suburbs with downtown areas are being built through the middle of long-established business and residential neighborhoods. The public becomes aware of blasting by two physical sensations-vibration and noise. Vibrations are usually so slight as to be negligible, and in most cases the only sensation noted is noise. The reduction of vibrations to this low level has been primarily achieved by the use of blasting practices and explosive products recommended by vibration engineers based on seismograph recordings. Unfortunately, very little scientific attention was given to the accompanying physical sensation-noise.

Jan 1, 1962

By M. C. Radomsky

Approximately sixty, small, surface coal mines in Pennsylvania participated in a program designed to improve safety performance in the workplace. The method involved the use of safety sampling and observation to assess the safe standards of worker behavior and work conditions. Data were collected through the use of operation-specific, on-site safety records covering seven major occupational units. Workplace events observed (acts and conditions) were assigned a hazard classification; feedback, both immediate and delayed was initiated to improve safety performance. The experiences drawn from this pilot project have proven the need to continue to pursue this behavioral approach; however, a stricter methodology needs to be adopted in the collection and analysis of data.

Jan 1, 1987

By Harold L. Lovell

The areas of application, the limitations imposed by water chemistry as well as the advantages and disadvantages in the use of limestone for the treatment of coal mine drainage have recently been described by the authors (1),(2), (3). The process has been demonstrated in continuous, full-scale operation to yield a treated water meeting specifications established by the Pennsylvania Sanitary Water Board and containing excess alkalinity. Their final pH levels are usually less than seven, a condition which avoids consumption of excess neutralization reagents, but which occurs with lime-based processes and results from unwanted side reactions. Operating experience has been cited by Calhoun (4) using ferric waters while others (5), (6), (7), (8), (11), have reported on related research efforts. Despite the advantages including ?the relative simplicity, and minimal costs of the process, there have been very limited industrial applications of mine drainage neutralization with limestone. Although any treatment of these waters may be considered as a temporary control measure (9), the lack of feasible, immediate alternatives, the extensive magnitude. of the waters and the high cost of treatment requires that optimum processes should be utilized and that operating experience in their use be developed as is feasible. This paper will review treatment experience with a ferrous water of moderate pollution loading .

Jan 1, 1972

By Jerome A. Westphal

The Middle Mississippi River extends from the mouth of the Ohio River to the mouth of the Missouri River, a distance of about 310 kilometers (km) measured along the river. From its founding in 1764 to the first steamboat arrival in 1817, the City of St. Louis was little more than a trading post. However, with the advent of the shallow-draft steamboat, the Middle Mississippi River rapidly became a major thoroughfare of commerce. In this regard, its importance has been reflected by the development of port facilities at St. Louis and by Federal activity relating to channel maintenance and improvement. First Federal work on the Middle Mississippi River was autho¬rized by Congress in 1824. This work was for snag removal and bank clearing and was directed at reducing the hazards to steamboat traffic, particularly during low-flow periods. During the 1820's and early 1830's, the main channel threatened to move toward the Illinois shore and abandon the St. Louis port facilities. In 1836 and 1837, Congress authorized construction of permanent improvements to keep-the river next to St. Louis (Missouri shore). By 1880, it was recognized that bank clearing activities had resulted in a wider and shallower river which exacerbated navigation

Jan 1, 1977

By E. F. Draskovich

In 1984 a high temperature heat recuperation system was installed in the pellet plant of the National Steel Pellet Company located in Keewatin, Minnesota. The system is similar to those of Cleveland Cliffs Empire and U.S. Steel's Minntac operations. It recovers hot process air from the cooler by induced flow, and directs it to an intermediate zone between the drying and preheat zones on the grate machine. This system recently underwent further modifications in April 1985, following initial operation in 1984. The M. A. Hanna Company, which manages the property, developed the design criteria and made the subsequent recommendations for modification through its research facility in Nashwauk, Minnesota.

Jan 1, 1986

By R. C. Milici

Historical production data and reserve decline rates can be used both to predict future coal production rates and to estimate when the reserve will be depleted. Reserve estimates inferred herein from historical production data and decline rates are commonly lower than estimates made from geologic data. The latter include significant amounts of lower quality (deeper, thinner, higher sulfur) coal which may be mined when the better deposits are depleted.

Jan 1, 1997

By T. Bui

The shut-off value for a panel cave mine determines when a draw point will be shut-off and mining will cease from that draw point. Using a shut-off value strategy for a panel cave mine is similar to using a cut-off value strategy for an open-pit mine. This paper will discuss how to choose an appropriate shut-off value strategy that an engineer can use when planning a panel cave mine to increase the net present value (NPV) of the project. Using a shut-off value equal to the mining and processing cost will provide the total mining reserves for a panel cave mine given a specified footprint. When the net present value analysis method is used to compare one design to another then using a shut-off value greater than the mining and processing cost will generate a higher NPV. This strategy will replace the marginal ore at the top of a draw column with higher grade ore at the bottom of newly opened draw points. A draw column is broken material which sits above a draw point and it is mined to a specified height above the draw point. This height is called the height of draw (HOD). Varying the shut-off value over the life of the mine can increase the NPV even further. This strategy would have a high shut-off value during the early stages of a mine and low shut-off value during the later stages. If the shut-off value is too high then too many tonnes would be left behind the draw point and the overall value of the mine will be decreased. Also with a high shut-off value then the production target may not be maintained due to too many draw points closing too soon.

Feb 23, 2014

By J. Boldy

The discovery of the Delbridge massive sulphide deposit in the Noranda district of Quebec resulted from an appreciation of the significance of a mercury leakage halo as a litho-chemical pathfinder to blind ore, coupled to its location relative to a geologically inferred ore-bearing horizon within complex volcanic stratigraphy. Systematic sampling of micro-fractures present in outcrops delineated a diagnostic anomaly, drawing attention to an area considered prospective for buried ore. The massive sulphide deposit was subsequently found to be blind and topped at the 110 metre level.

Jan 1, 1984

By John G. Oldsen

During the last several years, implementation of trusses, in lieu of wood cribs, has been successful for supplemental tailgate support in the Pittsburgh seam. This paper reviews the truss support system provided by the new high strength 0.6" tensioned cable truss, which is now also being used in cribless tailgates. Cable loading and roof deformation were monitored to evaluate roof and floor performance. The test results indicate that the cable truss system successfully controlled the roof and floor during the first and second panel extraction. This paper will describe the advantages of cable trusses and their load transfer mechanism as well as mine evaluation.

Jan 1, 1997

By C. Einberger

Groundwater Monitoring is typically required by regulatory agencies at potentially hazardous landfills or surface impoundments. Agencies have often required an arbitrary number of wells with limited evaluation of the effectiveness of the network to detect a leak. A Monitoring Efficiency Model (MEMO) has been developed to improve the design and cost effectiveness of monitoring well networks. MEMO 15 an analytical model that simulates the migration of hypothetical contaminant plumes from a site and quantifies the efficiency of alternative well network designs in detecting the plumes. The computed monitoring efficiency provides a quantitative measure of the well network adequacy based on hydrogeologic considerations. The model was recently used to design the groundwater monitoring well network for a heap leach pad at the proposed Beartrack Project.

Jan 1, 1993

By A. K. Kuhn

In virtually all jurisdictions, comprehensive environmental protection regulations or standards are in place that apply to all industries, including mining. The only other legitimate mine-permitting concern is post-mining land use (PMLU). PMLU includes all uses of land after mining as well as the ecosystems appropriate for those uses. Although flawed, the New Mexico Mining Act (NMMA) of 1993 is a PMLU-based permitting statute. It requires measures during closure that will establish a PMLU or self-sustaining ecosystem for each mine unit. PMLU-based permitting avoids prescriptive, one-size-fits-all measures and keeps permitting focused on the legitimate goal of responsible land management..

Jan 1, 1999

By W. L. Hollinshead

For more effective and cost-saving production in tunnels, the machinery used on construction sites in the future will be equipped with guidance systems combined with working-procedure management systems. This paper describes sensors for these systems and vari¬ous system configurations. A project is described that uses a computerized guidance system on an underground mining machine for guidance and profile control.

Jan 1, 2000

By J. Carr

Ring gear and pinions used as the final drive on large metallurgical grinding mills are expected to transmit their rated horsepower reliably for long periods of time. Duty is 24 hrs./ day. Life expectancy of such gear sets is of the order of 20 years; that is, each gear and pinion flank is expected to resist failure by pitting for 10 years. This means that for a dual pinion gear set having a ratio of 18.42:1.0 and a mill speed of 10 RPM, every gear tooth will see 105.12 x 106 surface contact stress cycles and every pinion tooth will see 968.15 x 106 surface contact stress cycles in a 10 year period. The allowable surface contact stress on the gear and pinion is determined by the material hardnesses. The rule being the higher the hardness, the higher the allowable surface contact stress may be.

Jan 1, 1985

By P. R. Taylor

A reaction is evaluated by which heated and pressurized water is used to precipitate metal oxides from loaded Kelex 100 complexes. Pure copper oxide (CuO) and pure nickel (Nio) in powder form, and ranging in average size from 12 to 25 micrometers, were found to precipitate from copper and nickel loaded Kelex 100/kerosene complexes, by water heated and pressurized to between 374 and 400 °c and 2170 psig (148 atm) and 3500 psig (238 atm). The precipitation is suggested to result from hydrolysis of the metal, following exchange for the hydrogen in the phenolic hydroxyl of the Kelex 100 structure, enhanced by the conditions provided by heated and pressurized water. The reaction is believed to have the characteristics of homogeneous nucleation and heterogeneous growth. The effects of temperature, pressure, initial metal concentration and seed addition on the kinetics of the process were studied. In addition, characterization studies were performed on the reaction products. A detailed discussion of the experimental results is presented.

Jan 1, 1992

By B. M. Davis

Frequently ore reserve studies utilize samples from a series of drilling or other types of sampling campaigns. Sometimes there is a mix of sample types, say for instance, channel samples from underground workings and drill core from surface drilling. Since drilling, sampling, logging, and sample preparation protocols tend to change over time, there is always a question whether the samples give similar results that vary only by chance alone. The problem of comparing the various campaigns is complicated by the presence of spatial relationships among the samples. Geostatistical tests take the spatial correlation into account, but these tests may be complicated and cumbersome to implement. A comparison method based on familiar statistical graphics is presented which accounts for the spatial relationships. It allows comparisons to be made quickly by using simple statistical graphs such as scatterplots and boxplots.

Jan 1, 1996

The development of economical and effective treatment processes for solid and aqueous waste is a critical issue facing the mining industry today. Cyanide, nitrates and acid rock drainage are environmentally sensitive effluents that require treatment or containment for acceptable disposal. In situ biotreatment processes are an emerging technology (Thayer) for cyanide oxidation, denitrification, sulfide mineral alteration and metal re- mineralization. Biological cyanide oxidation is competitive with chemical treatment processes (peroxide, alkaline chlorination) for process solutions, spent ore and tailings detoxification. Microbial denitrification treats mine waste contaminated with nitrates from blasting, processing or nitrification of the host rock. Bio-alteration of sulfide minerals and metal re-mineralization may present the most cost-effective and environmentally acceptable method of dealing with sulfide tailings and leachate solutions. Field test programs for cyanide bio-degradation and denitrification of spent ore and process solutions were designed and run at two mines. Although the treatment bacteria and the application processes are similar, each waste presented site-specific problems for adapting the biotreatment processes. Some of the site problems include climate, ore geochemistxy, field bacteria production, waste microbiology and application engineering. This paper compares treatment design and results for cyanide oxidation and denitrification in heap detox treatments.

Jan 1, 1992

By Terry D. Vandell

The purposes of this presentation are: (1) to discuss the actual as well as potential incidents that have caused and that could cause groundwater contamination at uranium in situ leach mining sites and (2) to discuss remedial actions and solutions that have been or that could be implemented in the future to stop or prevent serious groundwater contamination from in situ leach mining in Wyoming?s Powder River Basin. Open pit, underground, and existing and proposed in situ leach uranium mine sites in the Powder River Basin are shown in Figure 1. In situ leach mining or solution mining for extracting minerals in liquid form is a relatively new addition to the list of conventional mining methods currently used to extract uranium in Wyoming's Powder River Basin. Basically, the in situ leach mining method involves: (1) the injection of a leach solution lixiviant (an acidic or basic oxidizing solution) into a uranium-bearing ore body, via injection wells, to complex the contained uranium, (2) mobilization of the uranium complex from the host material via creation of a soluble complex salt, and (3) surface recovery of the solution bearing the uranium complex via production wells. Uranium is then separated from the leach solution by conventional milling unit operations (ion exchange).

Jan 1, 1981

By R. K. Mehta

Stirred ball mill feed used for ultra-fine grinding application requires fine size separation step in order to avoid over-grinding. This paper presents the selectivity curves obtained for oil shale and complex sulfide are using 460 mesh (30 micron) Derrick vibrating screen. Interestingly, the selectivity curves generated from the experimental data were monotonic increasing selectivity for oil shale but not monotonic increasing for sulfide ore. These non-monotonic increasing selectivity curves were similar to the mechanical air separator fishhook selectivity curves described by Luckie and Austin. A 2 stage classification in series model describing the fishhook selectivity curve has been used in proposing the classification mechanism for fine vibrating screens when heterogeneous multicomponent sulfide are undergoes size separation.

Jan 1, 1992

By Kendall Y. Keuhey

The Mercur Mine, developed and operated by Getty Mining Company, is designed to process 3,000 tons/day of gold ore from the historical Mercur Hill mining district. The mill process involves crushing, grinding, and cyanide carbon in leach for recovery of gold ores ranging from 0.08 to 0.10 oz/ton. During the mining of normal grade ore, a substantial tonnage of material containing 0.02 to 0.05 oz/ton is mined and would be available for heap leaching. Also, Getty Mining is developing methods to test and prepare lower grade material for heap leaching by rejecting a course rock fraction from the grinding circuit SAG mill. This lower grade fraction is suitable for heap leaching, and its removal will upgrade the regular mill feed. Other test methods are directed toward leaching techniques on some 4.0 million tons of tailings that resulted from roasting and/or cyanide leaching Mercur ores in the early 1900s. The natural carbons associated with the Mercur deposits require special treatment to reduce their gold adsorption effects when leached with cyanide.

Jan 1, 1983