Search Documents

By Ben Benally, Joseph M. Hans

INTRODUCTION The decontamination of the former Shiprock uranium millsite and the interim stabilization of its tailings piles began in March 1974, and ended in June 1978. Personnel monitoring for whole body gamma ray exposure was conducted for selected individuals working at the mill site throughout most of this period. The millsite and exposure conditions are briefly described to develop a basis for interpretation of the exposure data. Millsite The Shiprock uranium millsite is located in the community of Shiprock, New Mexico on a bench overlooking the San Juan River (Figure 1). Both Shiprock and the millsite are located on the Navajo Indian Reservation. About 1.5 million tons of tailings were produced on the millsite during its operation from 1954 to 1963. The tailings were pulped with waste process fluids and water, and discharged to form two tailings piles. The piles (ponds, dams) were formed with earth starter dikes and the dikes were then raised using the separated sand fraction of the tailings. The slime fraction of the tailings were discharged into the diked impoundment. The mill was shut down and partially dismantled before the lease expired in 1973, and the remainder of the mill and tailings reverted back to the Navajo Tribe which was the lessor. Portions of the millsite were then occupied by the Navajo Engineering and Construction Authority (NECA), a tribal enterprise. In addition to its regular activities, NECA established an on-site training school for heavy equipment operators. The trainees principally used the south tailings pile as a practice area and spread the tailings into a 10 hectare row of raffinate ponds located along the southwest side of the millsite. Overall, the training activities inceased the effective area of the tailings piles from 20 to 35 hectares. Another 56 hectares were contaminated with wind and water eroded tailings. Exposure Conditions Persons decontaminating a millsite may be subject to radiation exposures from several sources. Only whole body gamma exposures are discussed in this report. These exposures are arbitrarily divided into three levels: high, intermediate, and low. The levels are related to areas in which the decontamination work was being done and have no connotation concerning imminent hazards. High exposures would result when persons were working with raw tailings, and intermediate exposures would occur when persons were working in the ore storage and mill yards. Low exposures would result from working in areas where surface contamination exists from wind and water erosion. [ ] The millsite and its contaminated environs were divided into major areas to facilitate the decontamination work (Figure 2). Areas A, B, and C are defined as perimeter areas containing surface contamination. Work in these areas was expected to result in low exposures. Areas D, E, and F are the

Jan 1, 1981

By R. Adsero

"A high altitude review of the state of the mining industry provided by a study of multifactor productivity shows a continuation of lower output year on year for the capital and labor inputs applied. The story is sadly similar for both U.S. mining and the Australian mining sector. In fact, according to PwC analysts, the world’s mining equipment productivity has declined 20 percent during the past seven years (Lumley, 2014). Although the reasons for the continuing decline in mining productivity are varied, the need for improvement is clear.The world’s mining industry fleet of more than 400 large draglines moves billions of tons of overburden and ore (phosphate, limestone, etc.) annually. This discussion will review a few of the tools available for improved productivity in dragline operations.Benchmarking equipment performance exposes the possibilitiesIn the September 2013 Mining Engineering cover story Graham Lumley and R. Adsero suggested that analyzing best practice equipment performance from an industrywide database for specific equipment performance improvement goals would be beneficial (Adsero, 2013). Benchmarking equipment performance by normalizing differences and then comparing specific measures of performance will provide a road map to improvement for those following the leaders. For those already performing at best practice levels, a benchmark confirms and bolsters what has already been achieved. As described in the SME February 2014 paper by this author, best practice is the average of the top 10 percent in annual output. Filling performance gaps identified by a comparison to best practice by investigating the details of the why and taking action to change, makes all the difference. This is true for all major mining equipment. Given the large gap between average performance and best practice performance most mining operations can benefit. Best practice performance provides a view of what is possible to the 90 percent majority of mining operations that are performing below the top 10 percent.For dragline mining operations, identifying specific characteristics and practices of leading dragline performance will provide a reference for comparison."

Nov 1, 2016

By Isabel F. Barton, MarkD. Barton, Christian A. Rathkopf

Molybdenite is the world’s principal source of rhenium (Re), a critical element in multiple high-tech applications. However, the Re contents in molybdenite vary by orders of magnitude on scales ranging from single grains to whole deposits. In order to better understand the systematics of this variation and what geochemical factors control molybdenite Re concentration, and hence overall Re resources, we examine global patterns in molybdenite Re contents through a compilation of > 3000 measurements of Re in molybdenite from > 700 mainly ore-bearing moderate- to high-temperature hydrothermal systems of different types. Our results are similar to but expand on those of earlier studies. Rhenium concentration in molybdenite has a lognormal distribution and varies systematically with type of geologic system, intrusive lithology, and Mo grade. The lowest-Re molybdenite occurs in greisens (geometric mean 1 ppm ± a multiplicative standard deviation of 9), quartz vein-hosted W-Sn deposits (2 ± 5 ppm), unmineralized granites and granodiorites (12 ± 8 ppm), intrusion-related deposits (24 ± 8 ppm), and porphyry W-Sn deposits (16 ± 11 ppm). Rhenium is most enriched in molybdenites from volcanic sublimates (23,800 ± 5 ppm), with skarn Fe and Au (560 ± 5 ppm and 540 ± 3 ppm respectively) and porphyry Cu and Cu-Au deposits next (470 ± 4 and 430 ± 7 ppm respectively). Among porphyries, skarns, and quartz vein-hosted deposits, Re is most highly concentrated in molybdenites from Cu and Au systems and its concentration decreases systematically through Cu-Mo, Mo, Sn, and W deposits. In nearly all cases, molybdenites from systems associated with intermediate igneous rocks contain more Re than molybdenites from systems of the same type with more felsic rock associations. The disparity between Re contents of molybdenite in felsic and intermediate systems is largest for porphyries, quartz vein-hosted, and skarn deposits and is near zero for subeconomic or barren granite and granodiorite Mo systems; felsic intrusion-related deposits have slightly higher molybdenite Re than their equivalents associated with intermediate intrusions. In most systems, molybdenite Re content does not correlate with metal grade, but may have an inverse correlation with Au grade in intrusion-related deposits (based on a small number of data points) and does exhibit a strong inverse correlation with deposit Mo grade. Dilution of Re through larger amounts (higher deposit grades) of molybdenite explains about 40% of this correlation, but the relative enrichment of Re in molybdenite from low-Mo deposits must also reflect some selective enrichment of Re/Mo in porphyry Cu systems compared to porphyry Mo systems. We found no evidence for secular increase or other systematic temporal variation in molybdenite Re content. The data regarding the use of molybdenite Re content as a proxy for mantle influence are ambiguous. Nearly all observed empirical correlations can be traced back to differences in redox state and sulfide concentration, the two geochemical factors identified here and by previous experimental work as the controlling influences on Re mobility under hydrothermal conditions. Hydrothermal systems with reducing conditions (W- and Sn-rich) tend to have low molybdenite Re even though compiled whole-rock data indicate that their source rocks have as much or more Re as those of more oxidized systems (e.g., Cu-rich). Vapor-phase exsolution, crustal assimilation, and mixing with external fluids may all enrich molybdenite Re concentrations in individual deposits and deposit types, but their extent and importance in overall hydrothermal concentration of Re is uncertain. Thus, it appears that the available molybdenite Re resource in an ore deposit largely depends on how the deposit’s redox and sulfidation conditions have varied over time and space during the timespan of hydrothermal activity. Oxidized, high-sulfide conditions tend to concentrate Re in molybdenite, whereas reducing conditions tend to leave Re dispersed at low concentrations in the bulk rock.

By Timothy J. Orr, Jami M. Girard

A NIOSH study on occupational deaths between 1980 and 1989 indicated that in the United States, mining had the highest average annual fatality rate (3 1.9 per 100,000 workers) of any other major industry. Since "lack of training" was often cited as the primary cause of accidents, NIOSH has been investigating new methods for effective training. One such method is the use of low- cost, desktop computers to simulate a virtual mining environment. Computer-based training offers several advantages over conventional training because the computer programs provide a three- dimensional environment that allows the trainee to practice using evacuation routes, encounter mining hazards, and view mining operations without being exposed to any real danger. One major focus of the project is mine escapeway multiuser training using desktop virtual reality programs. Researchers have imported mine maps into the software for the purpose of practicing actual evacuation routes and procedures. Various scenarios for evacuation can be practiced in a three-dimensional computer simulation of the mine in a disaster situation, complete with smoke, fire, and other dangers. Depending on the trainee's job description (i.e., foreman, shift boss, beltman, etc.), certain tasks need to be performed in addition to navigating primary and/or secondary escape routes. Each scenario allows for individual or team-based training and provides a means to educate mine workers in hazard recognition and hazard avoidance. Using this program, mine workers can practice evacuating various mine layouts without the danger and expense associated with escapeway training in an actual underground mine. Each scenario can be changed to test the trainee's reaction in a variety of circumstances and run many times so the trainee can practice concepts. This training experience will help reinforce the knowledge acquired during more conventional classroom instruction, and the inherent flexibility of the program allows training materials to be tailored to meet the specific requirements of individual mines.

Jan 1, 2002

By Bill A. Hancock

In Situ leaching for the recovery of uranium from low grade sandstone deposits is one of the newest technological advances in the mineral industry. It is rapidly developing into a commercially feasible mining system which has economic, environmental, and social advantages over conventional mining systems. Because of the current uranium shortage, development of In Situ leaching into a sophisticated system has gained new impetus. In Situ leaching will become an important mining technique in the future, which will greatly help to supply uranium for our nation's energy heeds. In this paper, I will be giving an overview of the merits of the system, as well as the technology, problems, and research in solution mining of uranium.

Jan 1, 1977

By Zhonglin Ye, Guangping Dai, Ba Zhang, Yonggang Wei, Shiwei Zhou, Bo Li, Hua Wang

Decreasing copper content in slag is critical for improving copper recovery, where apparent viscosity is the main factor affecting the separation of matte/copper from the slag. The viscous behavior of copper converter slag was investigated during reduction process in this paper, and its non-Newtonian viscous behavior and shear thickening characteristics were clarified. The effects of silicate structure and solid particles in the melt on the slag apparent viscosity were investigated. As slag cleaning proceeded in an electric furnace, the magnetite gradually transformed into ferrous oxide, increasing the FeO/SiO2 ratio. With this ratio increased from 1.2 to 2.0, the slag structure was simplified, and its apparent viscosity decreased from 0.26 to 0.12 Pa·s at 1523 K. The iron phase was excessively reduced to metallic state; the slag contained metallic copper-iron alloy particles, increasing apparent viscosity. The apparent viscosity and phase structure of the slag corresponding to the iron phase reduction process were analyzed in detail; the results obtained in the present study are of great significance to the reasonable control of the converter copper slag cleaning process.

Nov 7, 2022

By J. S. Rapp

This report is based on existing reports and recently gathered field data. It discusses mineral resource potential of Tertiary playas in the Fort Irwin region. An estimated 1.3 million tons of measured salt "reserves", and 20 million tons of indicated salt resources, have been identified north of the fort. Other indicated resources include 300,000 tons of celestite, 800,000 tons of gypsum, and 10 million tons of selenite. Zeolitic tuff was mined south of Fort Irwin from 1978 to 1984, and unexplored occurrences are widespread. Calcium-bentonite is mined near Barstow, and more may exist, including valuable sodium-and lithium-based bentonites.

Jan 1, 1992

By III Basham

As environmental laws and regulations become more complex and the economic cost of non-compliance becomes greater, periodic assessment of environmental compliance, identification of potential liability and implementation of any necessary remedial action should be a standard part of the operational methods of any successful business. The title of this paper "Environmental Audits, A Shield, A Sword or A Trojan Horse?" is intended to draw attention to the fact that environmental audits can be used positively to shield a business operations from actual or potential environmental liability; can be used proactively as a 'sword" in both a marketing context ("do business with us because we conduct our business safely and professionally?) and as a mechanism for developing positive relationships with environmental regulators; and, used negatively, as a "Trojan horse", by developing information which those same environmental regulators (or the public) use in an enforcement context against your business or that of your clients. This paper will discuss the concept of environmental audits in general; the pros and cons of conducting the same; and the role of the attorney, as part of the "audit" team, to insure, to the greatest extent possible, that the audit process is productive from both a managerial and legal perspective.

Jan 1, 1992

By D. Scott Barr

The Zarafshan/Newmont Joint Venture operates the Muruntau heap leach project, located in the Kyzylkum desert of central Uzbekistan. The mine produces more than 12.4 t/a (400,000 oz/year) of gold from low-grade oxide ore stockpiles adjacent to the Muruntau open pit. It is op¬erated by the Navoi Mining and Metallurgical Combine and is one of the largest gold resources known (Fig. 1). Since commissioning in 1995, total heap leach production has exceeded 21 t (675,000 oz). The joint venture uses four-stage crushing and screening to produce a final product for heap leaching, Merrill-Crowe processing and local refining.

Jan 1, 1998

By Mikael Ramström, Mark Board, Clayr Alexander, Wes Johnson

"The Coeur d’Alene mining district in northern Idaho was first discovered more than 130 years ago and has been the most prolific silver producer in the United States. The Lucky Friday Mine of Hecla Mining Co. (Fig. 1) is the oldest (76 years) and deepest mine in the district, producing approximately 725 t/day (800 stpd) from narrow, vertical lead-zinc-silver veins. Cut-and-fill stoping is currently employed at depths to about 2.3 km (7,500 ft) below ground surface, making it one of the three deepest mines in the western hemisphere. The #4 Shaft, a winze collared at approximately 1.8 km (5,900 ft) below surface and extending to a depth of nearly 2.9 km (9,600 ft), was recently completed to exploit the high-grade 30 Vein, whose resource has been identified to at least 3 km (9,700 ft) in depth.As with other deep mines worldwide, a number of challenging engineering issues occur, including: high in situ rock stress, squeezing ground, seismicity, high in situ rock temperature that requires refrigeration, diesel equipment that generates diesel particulate matter (DPM) requiring high ventilation airflow rates and long travel times for worker transport to mining areas.This article describes the methods that Hecla Mining Co. has employed during the past 50 years to combat these issues, with emphasis on the current efforts to implement continuous, mechanical mining with automated or teleremote operation and to introduce electric and battery-powered equipment to minimize refrigeration and ventilation requirements for the removal of DPMs.Geology and in situ stressThe host rock mass is an extremely thick sedimentary sequence (the Belt Series) that has been tilted vertically by mountain building. The rock mass in the current section of the mine consists of weak, heavily foliated argillites and stronger, bedded silty-argillites termed siltite. The vertical veins (80° to 85° dip) are parallel to the foliation with an approximate width of around 3 m (10 ft). There are two regional, vertical faults that parallel the vein; one forming the hangingwall of the orebody and one approximately 90 m (300 ft) in the footwall. Additionally, there are several thin, rough northdipping faults that occur in the footwall of the vein which terminate on the major vertical faults.Both the argillite and vein package rock have moderate strength, with uniaxial compressive strength averaging about 100 MPa (14,700 psi with a range from about 70 to 125 MPa), and are moderately abrasive, with CERCHAR abrasivity index of 2 to 3. The major in situ stress is horizontal and oriented in a northwest direction with magnitude about 1.5 times the vertical stress. Consequently, the Lucky Friday stress magnitude at depth is analogous to significantly deeper South African gold operations."

Jan 12, 2017

By Alfredo Valdivia, Jesus Schabib, Vojtech Gall, William Cao, Curt Cicileo, Andrew J. Thompson

"The East Side Access Project (ESA) involves the construction of geometrically complex underground structures including a large number of caverns and bifurcations. Initially conceived as dual lined structures with either traditional concrete or shotcrete final linings (SFL), construction economy, advances in concrete placement technology and scheduling among others led to a wide use of what is referred to as freeform or pneumatically applied concrete (PAC) for the construction of tunnel final linings. PAC is a method of applying concrete without using formwork, where a wet mix concrete is pneumatically installed to encase reinforcement to full lining thickness. PAC has been widely adopted at ESA well beyond initial expectations. The paper addresses the design and construction aspects of the PAC method and contrasts it to traditional SFL lining placement. The experience made provides guidance for future PAC and SFL applications. THE EAST SIDE ACCESS PROJECT AND USE OF FREEFORM CONCRETE The Long Island Rail Road (LIRR) currently transports commuters from Long Island into Manhattan, terminating at the already congested Penn Station on the west side of Manhattan. Once completed, the ESA Project will provide LIRR commuters direct access to the east side of Manhattan underneath Grand Central Terminal. The ESA Project will help alleviate the congestion at Penn Station, which currently accommodates New Jersey Transit, Amtrak, and LIRR lines; reduce travel time for LIRR passengers traveling to the east side of Manhattan and facilitate connections to the New York City Transit (NYCT) Subway System and Metro North Rail Road. The construction includes mining and lining of new tunnels and facilities under Manhattan and Queens. The tunnels run from Queen’s Sunny Side Yard through the existing 63rd St. Tunnel, underneath Manhattan’s Park Avenue until termination at 37th Street. Differing types of tunneling methods and final lining systems are being used depending on the ground conditions, geometry and size of the excavation, site constraints and functional requirements. Mining of the Queens segment of the ESA Project involved soft ground tunneling by pressurized face tunnel boring machines, cut and cover construction, and conventional tunneling. The Manhattan segment of the ESA Project involves mining in hard rock by tunnel boring machines, drill and blast, and road header."

Jan 1, 2016

By D. W. Mitchell

Planning today for what hopefully will never happen is one of the surest ways to decrease the chance of it happening. As Napoleon proved and Ian Mitroff wrote, "The heat and stress of battle is the worst time to make decisions of strategic importance." Mitroff also wrote, "The value of a plan is not that it will ever perfectly match reality, but going through the process of planning speeds the process of recovery. It allows the organization to emotionally work through the worst before it actually happens." This paper concentrates on things miners must consider; on the need for plans to be like a belt conveyor strong enough to carry the load, flexible enough to stretch a little; on the criticality of throwing away fax machines and telephones, and having certain officials at the scene rather than back in head-quarters; on the training of fire brigades and mine-rescue teams; on having company-controlled chromatographs; on having people who can look at trends rather than numbers. Some of the things in this paper might anger some readers; for that, I can only ask them to consider first the problem not their position.

Jan 1, 1993

By Jeremy Cawley, Horry Parker Jr., Clint Wilson

The 5180 m EPBM drive on the Lower Olentangy Tunnel (LOT) is predominantly within glacial overburden. To connect LOT with the existing OARS deep tunnel in limestone bedrock, the upper 15 m inside diameter Vine Street retrieval shaft telescopes down to 6.7 m in diameter and extends into the karstic Columbus Limestone to a depth of 51 m, where a 104 m SEM tunnel will connect to OARS shaft 6. Pre-excavation grouting was reuired prior to lower shaft excavation to reduce potentially high groundwater inows. This paper discusses the secant pile installation, grouting program, shaft excavation, and hydrogeologic observations.

Jun 23, 2024

By Karl Gunnar Holter, Frank Clement

"INTRODUCTION Typically waterproofing of conventionally excavated tunnels has been done by installing pre-fabricated sheet membranes between the primary temporary support lining and the secondary permanent inner lining. The membrane acts as a separation or sliding layer between the linings, which is often desirable. The geotextile installed behind the sheet membrane provides the required drainage and protection of the system. The design of the tunnel lining is strongly influenced and limited by the use of waterproofing sheet membranes. Since primary and secondary linings are separated from each other, forming a double-shell lining system. In that case the secondary lining must be designed for all permanent loads, although the sprayed concrete primary lining continues resists ground and water loads for a long time after construction. Significant progress has been made in sprayed concrete technology over the last two decades, with advanced admixtures, as well as the improved application technology using spraying robots. The development of new admixtures like superplasticizers based on poly-carboxylates, alkali free accelerators and silica fume, enables designers to use permanent sprayed concrete linings (SCL) increasingly for long-term service life. When designed and applied correctly, sprayed concrete can be considered as permanent. The use of spray applied membranes has seen increased use over the last decade in some countries, and demonstrated functionality and cost-effectiveness in several situations. This paper describes the use of the sprayed waterproofing membrane MasterSeal 345, an EVA polymer based product, and the practical experiences from several projects. SPRAY APPLIED WATERPROOFING MEMBRANES The sprayed waterproofing membrane is polymer based and has been especially developed for underground structures. The membrane is applied between primary and secondary concrete linings and develops high bond strength on both sides to the concrete (doubled-bonded)."

Jan 1, 2016

By Praterm J. D.

The process parameters for effective utilization of nitric acid as an oxidant for copper-iron sulfides have been developed. Leaching variables found to be important were acid concentration, temperature, time, atmosphere, pressure, mineral type, particle size, and percent solids. Particular attention was devoted to analysis and control of fumes evolved during the oxidation. Responses recorded were metal extraction, elemental sulfur formation and oxidation, product gas composition and evolution rate, reagent consumption, and residue flotation response. The paper concludes by laboratory testing a flow sheet based on the above observations. Ninety-eight percent of the copper contained in a chalcopyrite-bornite concentrate was recovered, requiring 1. 6 pounds of nitric acid to be regenerated externally per pound of copper extracted. Iron remained in the leach residue as hydrogen jarosite and was ultimately rejected from the system by froth flotation. Sixty percent of the sulfur contained, in the heading concentrate reported in the elemental form; the remainder was oxidized to sulfate and eliminated with the hydrogen jarosite in the flotation tails or by neutralization of the solvent extraction raffinate with lime. Nitrogen was evolved primarily as NO and NO2; up to 3 percent N2O was also present. Gases containing sulfur were absent except when pyrrhotite was solubilized in the absence of soluble copper. In this case, H2S was evolved.

Jan 1, 1972

By Dennis K. Mortensen

The warm southwestern desert of Arizona is an ideal location for ASARCO's new Sacaton Unit. The climate of this arid region played a major role in the design considerations of the Unit's crushing and concentrating facilities. Low yearly rainfall and relatively high yearly temperatures are a combination that was taken advantage of when designing the surface facilities. The plantsite, located due west of the mine pit, is in an area originally covered with sparse desert vegetation, underlain to an average depth of 125 feet by desert alluvium. The entire plantsite area slopes gently to the southwest at approximately 1%. Ground conditions at the plantsite area were not acceptable for construction due to the collapsability of the wetted soil when under loaded conditions, Overburden from the pit area was used to form the foundation for the entire plantsite. This waste material, entirely devoid of rock, was placed and compacted to an elevation approximately 20 feet above the desert floor. Elevating the plantsite by filling with waste material not only provided an adequate construction foundation but also eliminated the possibility of flooding from run-off in the surrounding desert areas.

Jan 1, 1974

By I. Ward, E. Milosavljevic, M. Botz

"The silver nitrate titration method is a rapid and acceptably accurate means of analyzing for cyanide in leach solutions that contain primarily free cyanide. However, in leach solutions containing elevated levels of copper, the titrimetric method overestimates the concentration of free cyanide and underestimates the concentration of weak and dissociable (WAD) cyanide. The authors have developed a modified potentiometric (MP) titration method for determining WAD cyanide that overcomes issues associated with high copper levels in solution. The new MP-WAD method involves addition of a chemical ligand to the sample prior to silver nitrate titration to release cyanide bound to copper. Once released from copper, cyanide in solution is no longer affected by the presence of copper, and titration results are quantitative rather than empirical. In multiple laboratory trials with synthetic solutions and complex actual leach solutions, analytical results obtained with the new MP-WAD method were found to be within about ±5% of analyses obtained with the USEPA OIA-1677 WAD cyanide analytical method.IntroductionThe silver nitrate titration method is widely used to estimate the concentration of cyanide in leach solution for purposes of cyanidation process control. Cyanide determined by silver nitrate titration is commonly referred to as “free” cyanide, but frequently should be referred to as “titratable” cyanide. By definition, free cyanide is the sum of the concentrations of aqueous hydrogen cyanide HCN(aq) and the cyanide anion CN- (ASTM, 2010). Titration will only yield a reasonably accurate measurement of free cyanide when metal-cyanide complex concentrations (e.g., cadmium, copper, mercury, nickel, silver and zinc) in solution are low. In other words, titration will only yield a reasonably accurate measurement of free cyanide if the solution primarily contains free cyanide."

Jan 1, 2015

By B. Anamaeric

Economic, environmental and operational disadvantages of the traditional blast furnace process has led to the development of direct smelting reduction processes, including those that utilize self reducing/ fluxing dried greenballs as iron oxide feed materials. This is mainly due to improved carbothermic reduction, carburization and reaction kinetics. In this paper, the morphological changes of the greenballs as they transform to pig iron nuggets are examined over time at a constant temperature of 1,400° C. The products produced after each treatment were characterized using optical microscopy, scanning electron microscopy/energy dispersive spectroscopy and point counting/image analysis. The changes in the percent metallized area, wustite dendrite and slag matrix content of the structures were calculated. It was determined that the transformations were initially controlled by dissolving and containment of iron oxides in the molten slag and their consequent reduction to iron, followed by coalescence of the metallized areas. The final transformations were controlled by the carburization of the metallized areas.

By E. Watkins, V. Gangrade

Large-opening stone mines often rely on natural ventilation and a network of auxiliary fans to produce adequate ventilation conditions in the mine instead of main mine fans, which are commonly utilized in coal mines. Large air volumes in underground stone mines, poor ventilation practices, and low operating budgets for mine ventilation potentially increase mine workers’ risk for dust, silica, and diesel particulate matter (DPM) emissions exposure. To help improve mine ventilation practices, the optimal auxiliary fan location for maximum airflow production from a ventilated intersection was determined using a combination of field measurements and computational fluid dynamics (CFD) modeling. In this study, conducted by researchers at the National Institute for Occupational Safety and Health (NIOSH), airflow quantity and fan data were collected at a partner mine to be applied as CFD model input parameters and comparison data for model validation. A six-foot diameter auxiliary propeller fan was introduced into the validated CFD model at three locations at a mine entry intersection with established ventilation flow perpendicular to the fan direction. Placing the fan on the opposite side of the intersection from the target active face area produced the highest ventilation flow rates at the downstream locations tested and produced the lowest amount of air re-circulation. The findings show that optimizing the placement of an auxiliary fan may increase the net effective ventilation flow rate by 70,000 cfm and reduce recirculation by 26%, which maximizes the potential effectiveness of large-opening stone mine ventilation systems and decreases mine worker exposures to airborne contaminants.

Mar 2, 2022

By L. B. Paterson

Mining Engineers throughout the world have an appreciation for the importance of the role of the Blasthole Drill in one of the primary elements of the mining process. This paper highlights areas that could influence the overall cost effectiveness of that process of breaking rock and how equipment is designed and configured to meet that challenge. Factors influencing drill productivity and overall cost effectiveness are addressed, both in the Mine Environment and on the Blasthole Drill.

Jan 1, 1999