Search Documents

By R. M. Cox

The ground forces generated by a properly installed and tensioned mine roof truss assembly can provide permanent mine roof support, even in severe ground conditions, either by direct suspension of the rock loads within the potential failure zone above the mine opening or indirect reinforcement of the natural rock arch that tends to form within the immediate mine roof. Notable advancements in mine roof truss support systems hardware and design technology have occurred since the introduction of the in situ mine roof truss concept for permanent mine roof support in 1966. The systematic installation of mine roof truss support systems has proven to be a very effective method of mine roof control room and pillar mines under a wide variety of ground conditions, even in areas otherwise considered unmineable because of severe roof control problems. Properly designed mine roof truss systems have also been used for permanent support of mine slopes and haulage tunnels.

Jan 1, 2002

By T. Mills, M. Evatz

Newmont’s Lone Tree Mine, located in northern Nevada, is an open pit gold operation supported by a standard truck and shovel mine production fleet (Caterpillar 785Bs and Hitachi EXs). Newmont continues to search for ways to decrease capital expenditure and lower operating cost, hence the implementation of the Ultra Light Body (ULW) concept. The fundamental idea associated with the ULWs is the increased payload potential. Economic justification comes from successful achievement of additional payload, within the truck’s rated GVW, without changing its loading and hauling characteristics. The increase in payload capacity allows equivalent tonnage movement using fewer trucks.

Jan 1, 2001

By Albert Ruiz

South Coast Water District (District) operates the Beach Interceptor Sewer Tunnel (BIST) in South Laguna, Orange County, California between Mon-arch Beach and Aliso Beach (Figure 1). The 10,424-foot long BIST houses a 24-inch Techite gravity sewer pipeline critical to the District Sanitary Sewer Collection System that conveys 1 MGD of raw sewage to a wastewater treatment plant. The original tunnel was constructed in 1954 and the sewer line replaced in 1974. Periodic inspections by sewer pipeline maintenance crews have documented deterioration of specific intervals of the tunnel within the past few years (Sancon 2003). Rotting timber supports and rock falls in the tunnel as a result of the deterioration were endangering the sewer pipeline. A 50-foot section of the tunnel was determined to be in need of immediate repairs, which were carried out from January to August in 2007. This section was enlarged to a horseshoe shape and lined with shotcrete. The pipe was encased in concrete in the invert of the new enlarged cross section. Hatch Mott Mac-Donald (HMM) designed the emergency repairs, carried out an assessment of the rest of the tunnel alignment, and is currently developing a work plan for rehabilitating the entire tunnel.

Jan 1, 2008

By Phillip E. Butler

Since early 1973, the Pennsylvania Department of Transportation (PennDOT) has been actively engaged in the utilization of coal mine refuse in the design and construction of highway embankments. The Soils and Geological Engineering Division of the Bureau of Materials, Testing and Research has the task of managing the program which includes field investigations, laboratory testing, engineering evaluation, planning, coordination, implementation, construction control, and review of construction performance. The objectives of the utilization program, in removing colliery refuse banks and utilizing the material in construction, are the environmental and aesthetic rehabilitation of those areas in the Anthracite and Bituminous coal fields which have been plagued for such a long time by air and water pollution, and unsightly landscapes; and the economic rehabilitation of those areas occupied by refuse banks by providing usable land which can now be developed as residential, business, or industrial sites.

Jan 1, 1975

By Stavros H. Constantopoulos

Mediterranean regions such as Greece, Turkey, Cyprus, Corsica and New Caledonia have experienced epidemics of malignant mesothelioma as a result of non-occupational, ??domestic?? exposure to tremolite asbestos and fibrous erionite. This exposure to tremolite asbestos and fibrous erionite is typified ??domestic?? due to its prevalence in regions with natural deposits of tremolite asbestos (or fibrous erionite) where the material from tremolite asbestos or fibrous erionite is used for domestic applications such as whitewashing. However, these exposures may be useful in examining the potential consequences of even small amounts of amphibole asbestos fibers in the ambient air. It can also elucidate the effects of fibers that behave like amphibole asbestos. However, this type of exposure is not useful for studying the potential effects of small amounts of asbestos in the ambient air of big cities due to the differing nature of the fiber types and modes of exposure between the regions. © 2008 Published by Elsevier Inc. Keywords: Tremolite asbestos; Erionite; Domestic; Environmental; Exposure

Jan 1, 2007

By S. K. Sharma, ANKUSH GALAV, G. S. P. Singh

Providing a suitable protective water barrier pillar (PWBP) is common to reduce inundation hazards in underground coal mines. The imperative factors influencing its performance include the water head acting on the pillar, cover depth, pillar width, strength properties, and permeability characteristics. The mechanical failure of such pillar is a stress-controlled phenomenon, whereas the hydraulic failure is a strain-based phenomenon. A finite-difference numerical modeling approach was developed to study the hydro-mechanical coupled behavior of protective water barrier pillars. The mechanical stability was evaluated in terms of the percentage of failed (ZoF) and intact zones. The influence of the strain-controlled weakening on the permeability of the flow medium was studied through the coupling of the mechanical and hydraulic effects. The coupled steady-state model was used to estimate the outflow rate and its hydraulic stability. The adequacy of the protective pillar was also investigated by assessing mechanical stability and capability to resist hydraulic pressure against the maximum expected water head. A seepage rate-based classification system has also been proposed to evaluate the seepage potential and assess the hydraulic stability. The model has been validated for two case studies at the cover depth of 136–189.5 m and the existing pillar width of 16–42 m against the water head of 25–141 m.

Aug 18, 2022

By William R. Yernberg

What a difference a year makes. One year ago, the iron mining industry and the steelmaking industry in the United States were in trouble. Many companies were in bankruptcy, and talk of plant and mine shutdowns was rampant. At that time, it seemed difficult, if not impossible, to remain competitive with imported steel. In addition, the World Trade Organization declared as illegal the tariffs placed on imported steel. And many questioned the viability of the ironmining and steel industry in the United States. At that time, global economic conditions were the main contributors to the industry’s problems. However, since last year’s meeting, changes in global economics have actually helped the steel industry in the United States. Heavy global demand for steel has caused raw-material shortages worldwide. Much of the increased demand is a result of the economic boom in China. In addition, because of a weak U.S. dollar and higher international freight rates, steel imports into the United States have been reduced to about 50 percent of recent levels. These factors have contributed to a rebirth of the U.S. iron mining and steel industries.

Jan 1, 2004

By Roy A. Grancher

?The Horn of Plenty seems to have sprung a leak?.? anonymous For the first time in the Nation's peace-time history, shortages have become a way of life for the United States. Such words as scarce, tight, and critical are used in regard to supply, leading to priorities, allocations, and possible rationing as make-shift attempts to satisfy demand. Almost every day a new type of shortage appears in another product area that has traditionally been taken for granted as being in perpetual abundance. The range of coverage extends from basic commodities such as oil, chemicals, cement, steel, copper, cotton, etc., through to machine tools, motors, bearings, electronic components, etc. , to those finished outputs that satisfy our fundamental requirements for food, clothing and shelter. Signs of the times appear in cancelled airline flights, unfilled lines at gasoline stations, no available home freezers, lengthy delays in any furniture deliveries, or to that little old lady seen walking out of a local supermarket clutching her hoard of twenty rolls of toilet paper. What a sad commentary to have to make about our Land of Plenty, so long the envy of the World for its material wealth -- and today with its initials "U. S." seemingly standing for ?Unlimited Shortages.?

Jan 1, 1974

By Thomas Sisley, Jozef Zurawski, Richard Switalski

Hilltop Interceptor Contract G is one of the segments of the wastewater control system in the greater Cleveland area. The tunnel is a relief interceptor constructed by the Northeast Ohio Regional Sewer District to minimize combined sewer overflows in the Easterly Service Area. The design study identified the need for a 3.35 m (132 in) diameter, 3.35 km (11,000 ft)in-line storage conveyance tunnel to be constructed at depths of 30 to 70 m (100 to 230 ft).Six structures for access, future flow drop, work shafts and overflow control were required to complete the system. The interceptor reduced the design peak flow from 12.5 m3/s(285 mgd) to 6.1 m3/s (140 mgd) by detaining in line 22,800 m3 (six million gallons) of wastewater.

Jan 1, 1997

By M. Westendorf, T. Banerjee, S. Kaushik, D. Tinney

"Cyclones are one of the most extensively used pieces of equipment within the mineral processing industry because of their simplistic operating and maintenance philosophies. They are commonly used as classifiers within the comminution circuit to control the grinding product particle size for satisfactory performance of downstream operations.Cyclones are a key contributor to the effective operation of the plant and have a significant impact on the mineral processing plant operations. If the cyclones are not performing as they should, the results are often a combination of lost recovery, grade, capacity and reduced throughput. Similarly, an inefficient cyclone operation may also lead to low or high recirculating loads that impact the efficiency of the comminution circuit. This highlights the importance of having proper stability in cyclone operation while implementing any plant-wide optimization strategy.One of the key challenges in cyclone operation is that cyclones are highly sensitive to changes in operating conditions and are affected by process fluctuations such as feed pressure, solids concentration and flow rates. Fluctuations in cyclone feed characteristics lead to unstable cyclone performance which affects mineral liberation. For such an impactful unit operation, cyclones have historically been under-instrumented in an otherwise highly instrumented process plant. Traditionally, mill operators have relied on visual observations of the apex discharge to determine the operating state of the cyclones. Visual cues corresponding to the different cyclone operating conditions have been discussed by Neesse et al. (2004) as shown in Fig. 1."

Jan 1, 2014

By Douglas Banks

Construction for the new 2.5 MGPD raw water intake project commenced December 2002. The project, initially designed as a 12' Ø concrete lined intake shaft,145' deep, with two offset 24" lake taps, 520' and 470' long was subsequently “value engineered” running the two lake taps through a single conduit. The offset for summer and winter pools was accomplished via a second shaft located at the lakes edge. Construction involved the use of blind drilling techniques for the shaft development and drill and blast techniques for the tunneling. All works were completed through extremely hard crystallized sandstone. The project came online August 12, 2004.

Jan 1, 2005

By Toby Mayo, Tassos Grammatikopoulos, Massoud Aghamirian, MARK FEDIKOW

The Zoro pegmatite project in east-central Manitoba occurs 20 km east of the historic mining town of Snow Lake. A composite sample (Master Comp) was prepared fromthree pegmatite zones within Zoro Dyke “D1” including the North, Central, and South Zones for mineralogical analysis and heavy liquid separation (HLS). The mineralogical examination was conducted on a subsample crushed to ca. P80 of 600 μm to determine the overall mineral assemblage, liberation of spodumene, and assess the potential recovery of spodumene by flotation. XRD and QEMSCAN results show that the sample consists of spodumene (10.5%), quartz (29.3%), plagioclase (29.0%), K-feldspars (21.3%), micas (5.1%), tourmaline (2.9%), and Fe-Mn-phosphates (0.1%). Spodumene is well liberated (88%), but also forms complex particles (7%), and middlings with quartz (4%). Liberation of spodumene increases from 81 in the + 600 μm to 95%in the − 106 μm size fraction. Liberation of quartz, feldspars, and micas account for 89%, 94%, and 83%, respectively. Electron probe micro-analyses and LA-ICP-MS showed that the average Li concentration is 3.7% in spodumene, 2196 ppm in micas, 1001 ppm in tourmaline, and 115 ppm in K-feldspars. Thus, spodumene accounts for 96%, micas 2%, Fe-Mn phosphates 1%, and both K-feldspars and tourmaline for < 1% of the total Li in the sample. The mineralogical data indicate the potential to recover spodumene by flotation with minimal Li losses due to other than spodumene carriers. Heavy liquid separation was conducted on the Master Comp which was crushed to − 6.4 mm, while the − 600 μmfractionwas removed fromthis test. The coarse fraction − 6.4mm/+ 600 μmwas subjected to HLS tests with eight heavy liquid-specific gravity cut-points (2.65 to 3.10 g/cm3). HLS indicates that it is possible to produce a high-grade lithium concentrate (close to 6% Li2O) after the rejection of iron silicates with magnetic separation.

Sep 16, 2020

By Christopher J. Bise

INTRODUCTION A mine&apos;s power system represents the driving force behind all of the extraction and auxiliary operations, because the production and transportation of mined material and the operation of equipment, such as fans and pumps, are all dependent upon a power source. Once, compressed air was the primary power source in mining; today, however, electrical power dominates. This chapter reviews the basic theories of com- pressed-air and electrical power and provides several examples of applications in mine power systems. COMPRESSED-AIR POWER General Compressed air has been, and should continue to be, an important source of power in mining operations. It has been used as a means of blasting coal in conventional mining and is widely used to operate stopers, mucking machines, and other air tools in both coal and hard-rock mines. Such applications demonstrate the suitability of compressed air for applications requiring linear motion, but it is also utilized for its reliability and safety. A compressed-air system is composed of a compressor, a receiver, a distribution network, and the air-operated machines. A compressor takes in air at normal atmospheric pressure (free air) and compresses it to a higher discharge pressure. The discharge pressure must be high enough to overcome the friction in the distribution system of pipes and hoses and deliver the compressed air to the machines at the pressure recommended by the manufacturer. The most common type of compressor used in mines is the reciprocating compressor in which the air is compressed by a piston in a cylinder. An air receiver is a container or storage tank that is located in the distribution system between the compressor and the machines. It stores compressed air, when the full capacity of the compressor is not being used, and gives a more steady flow of air to the machines. The distribution network consists of pipes, Oalves, elbows, tees, and hoses that transmit the compressed air from the receiver to the machines in the mine. It is essential that the distribution system be designed with the proper sizes and lengths of pipe, hose, and other components to keep pressure losses well within allowable limits. The air-operated machines consist primarily of drifters, stopers, pluggers (sinkers), slushers, and several other pieces of equipment. Compressor Operation Every compressor is made up of one or more basic elements; a single element, or a group of elements in parallel, comprises a single-stage compressor. Many compression problems involve conditions beyond the practical capability of a single compression stage. Too great a compression ratio (absolute discharge pressure divided by absolute intake pressure) may cause excessive discharge temperatures or other design problems. It, therefore, may become necessary to combine elements or groups of elements in series to form a multi- stage unit, in which there will be two or more steps of compression. The number of stages commonly used in reciprocating compressors is as follows: Pressure Number of stages 0- 150 pig 1 80- 500 psig 2 500-2500 psig 3 2500-5000 psig 4 When pressure is referred to as pounds per square inch gage (psig), it means the pressure (in pounds per square inch) above barometric pressure as measured by a gage. The sum of barometric pressure and gage pressure is the absolute pressure (in pounds per square inch). The gas is frequently cooled between stages to reduce the temperature and volume entering the subsequent stages, thereby reducing the work required for compression. The basic reciprocating compression element is a single cylinder compressing on only one side of the piston (single-acting). A unit compressing on both sides of the piston (double-acting) consists of two basic single-acting elements operating in parallel in one casing. The reciprocating compressor uses automatic spring-loaded valves that open only when the proper differential pressure exists across the valves. Intake valves open when the pressure in the cylinder is slightly below the intake pressure. Discharge valves open when the pressure in the cylinder is slightly above the discharge pressure. In Fig. 1, Diagram A shows the basic element with the cylinder filled with air at atmospheric pressure. On the corresponding theoretical pressure-volume

Jan 1, 1986

By L. F. Ruppert, W. D. Watson, S. J. Tewalt, L. J. Bragg

The U.S. Geological Survey recently completed a digital coal resource assessment model of the Upper Pennsylvanian Pittsburgh coal bed which indicates that of the original 34 billion short tons [31 billion tonnes] of coal, 16 billion short tons [14 billion tonnes] remain after subtracting mined-out coal. When technical, environmental, and social restrictions are applied to the remaining Pittsburgh coal model, only12 billion short tons [11 billion tonnes] are available for mining. Our assessment models estimate that up to 0.61 billion short tons [0.55 billion tonnes], 2.7billion short tons [2.4 billion tonnes], and 8.5 billion short tons [7.7 billion tonnes] could be available for surface mining, continuous mining, and longwall mining, respectively. This analysis is an example of a second-generation regional coal availability study designed to model recoverability characteristics for all the major coal beds in the U.S.

Jan 1, 2000

By M. H. Dunn, T. P. Danehy, C. F. Denholm, S. L. Busler

The problems associated with abandoned minelands are so extensive that neither federal, state, or local governments nor the mining industry nor watershed groups can adequately address these problems individually. By combining talents and resources, however, these problems are being solved efficiently, effectively, and economically. Utilizing existing water monitoring data, local public-private partnerships have successfully designed and built passive systems within five weeks to six months which treat discharges up to hundreds of gallons per minute that vary in quality from net alkaline to highly acidic, containing as much as 200 mg/L dissolved iron and 70 mg/L dissolved aluminum.

Jan 1, 2002

By William Gleason

Despite a global slowdown in most mining sectors, Caterpillar, the world?s largest mining equipment maker continues to forge ahead with new, and improved offerings to the global mining industry. On Nov. 10, as part of its Loading and Hauling Mining Focus Session at its Tinaja Hills proving grounds south of Tucson, AZ, Caterpillar unveiled to customers and media its two latest mining products, the 994K wheel loader and 6020B hydraulic shovel. The Caterpillar 994K wheel loader builds on a nearly 25-year history of the 994 model but with one noticeable difference ? the 994K is bigger ? much bigger. Weighing in at 239,142 kg (527,218 lb) the 994 K is up to 20 percent larger and comes with up to 30 percent increase in payload capacity. This behemoth of a machine is currently being tested at Caterpillar?s Tucson Proving Grounds, Anglo Gold Ashanti?s Cripple Creek and Victor gold mine in Colorado and Taseko?s Gibraltor copper and molybdenum mine in British Columbia, Canada.

By Brent A. Elliott, J. Richard Kyle

Texas is a major producer of industrial mineral resources required by the state’s ever-growing population that now exceeds 28 million. Texas typically ranks in the top three states for the value of non-fuel mineral production with a total value of $5.2 billion in 2017, accounting for 6.9% of the total US mineral value. Almost 90% of current Texas industrial mineral value comes from the production of cement, crushed stone, industrial sand, and construction sand and gravel. Construction material consumption is focused in the 25 metropolitan areas of the state with populations of > 100,000 residents. Industrial mineral consumption is dominated by the four most populous regions of the state—Houston, Dallas-Fort Worth, San Antonio-New Braunfels, and Austin-Round Rock—with an aggregate population of more than 18 million. More than 11,000 employees work in Texas mining and processing operations. Texas produces more crushed stone than any other state from more than 200 quarries; a similar number of operations produce sand and gravel. Specialty industrial sand production for use as proppants in hydraulic fracturing for enhanced petroleum production serves as an excellent example of how developments in one industry sector can markedly affect another industry; the production of industrial sand in Texas has markedly increased over the past decade, reaching $1.3 billion in 2014. With Texas’ population projected to reach 50 million by 2050, continuing in-state development and production of industrial minerals will be required to supply its residential, commercial, and industrial users. Favorable geology and economic factors provide opportunities for identification and development of new industrial mineral production sites.

By D. Brandt

The Dos Pobres Mine is a copper oxide heap-leach mine located near Safford, Arizona. Mine production is 180,000 tons (163,293 tonnes) per day with a stripping ratio of 2:1. During the startup phase of the mine, the required fragmentation size was easy to achieve as the ore was highly weathered and fractured near the surface. As the mine depth increased, the proper fragmentation size became harder to achieve due to less weathering and different rock types. Because copper recovery increases as crusher product size decreases, achieving the appropriate product size at the crusher is the operating priority. The Engineering Department started a project to improve fragmentation through blasting and thus increase throughput in the crushing system. It soon became clear that input from other departments was going to be required to make this a safe and economical project. Therefore the Crush and Convey and Ore Control departments worked together to evaluate all available data on blast patterns and explosive loads and tracked performance and results. Using image analysis, Drill Energy Index and databases, we have been able to improve fragmentation size and verify the results while controlling costs.

Jan 1, 2011

By Christophe Bragard, Brett Robinson

This paper reflects the challenges encountered during the construction of the light rail tunnels under Boyle Heights, in Los Angeles, California. Equipped with two state-of-the-art EPB TBMs, the construction team undertook the mining of twin bored tunnels in the Los Angeles alluvium. The gassy underground conditions dictated many aspects of the design of the tunnels, as well as the tools and means used for their construction. This paper will detail the challenges encountered during construction, as well as the means, methods and logistics used on the project. Discussion includes: EPB TBM machines with some very unique/specific features; complex assembly sequence due to limited shaft access; final precast concrete liner with double gaskets; NATM cross passage excavation in soft ground and below the water table; compensation grouting; mucking shaft arrangement.

Jan 1, 2007

By R. Barthel, O. Nitzsche, J. Pateiro Fernández, T. Cramer

The Hong Gai coal field in northeast Vietnam has been the main coal mining area of Vietnam for more than 150 years. Anthracite coal is produced from several open pit and underground mines situated close to the UNESCO world natural heritage site Ha Long Bay. The mining-induced environmental impacts such as dust emissions, acid mine drainage, and visual impairments due to waste dumps resulted in severe conflicts of interests regarding future land use and the protection of the world natural heritage site Ha Long Bay. Within the RAME project (Research Association Mining and Environment in Vietnam), Brenk Systemplanung is contributing to an improved environmental and sustainable planning in Vietnam&apos;s mining industry and the reduction of environmental impacts on Ha Long Bay by developing suitable and sustainable technology and planning measures (e.g. for dump construction/rehabilitation, predictive modelling, and/or monitoring) for Vietnam&apos;s leading coal producer.

Jan 1, 2011