Search Documents

By Francis X. Cannaday

The purpose of this investigation was to find whether the moduli of elasticity obtained were the same for the following methods : ( 1 ) Deformation of a borehole in a prism subjected to uniaxial stress ; ( 2 ) deflection of a thin beam of uniform cross section uniformly loaded ; ( 3 ) sonic - pulse velocity measurements , and ( 4 ) strain measurements on a prism under uniaxial stress . The rock tested was chosen for its good elastic behavior and relatively good homogeneity and elastic isotropism . The same rock was used for all methods . Results indicate that for given environmental and stress conditions the moduli obtained by each of the four methods check one another within the limits of experimental error and that the differences introduced which are characteristic for each method are smaller than physical variations within the rock tested .

Jan 1, 1964

By A. L. Engel

This investigation was undertaken to assess the feasibility of processing an extensive deposit of iron ore near Palisades, Eureka County, Nev., previously penalized for high phosphorus content. The experiments described indicate a satisfactory accomplishment of objective. Chemical treatment will permit a high-phosphorus iron ore to be used. Leaching with acid solution effectively lowers the phosphorus content with a [gligible] loss of iron. The use of hydrochloric acid is preferred because [ ] does not contaminate the ore and the cost is lower. Minus-1/2-inch ore was satisfactorily leached in 24 hours, minus-1/4-inch ore, in 8 hours, and minus-10-mesh ore, in 3 hours. About 40 pounds of acid per ton of ore was consumed in each instance.

Jan 1, 1959

By Richard L. Rains

The Bureau of Mines conducted a mineral investigation of the 29,000-acre Dixie Summit area near Elk City, Idaho, during the summer of 1989. At the Petsite mine a marginally economic, identified resource of 4.9 million tons with an average grade of 0.023 ounces gold per ton was delineated. Possible resources of gold, along with silver, copper, lead, and zinc, occur in at least eight other lode deposits. Placer gold may be recoverable by recreational-sized suction dredges in some stream drainages, Five lode mines in the study area have produced over 5,516 ounces of gold (placer gold production was not recorded), 4,757 troy ounces of sliver, 36,746 pounds of lead, and 3,800 pounds of copper. Current mining claims in or adjacent to the study area total 460 lode and 70 placer claims. There are two patented lode claims within the Dixie Summit study area.

Jan 1, 1991

By Quintin A. Aune

This report presents the results of a field and laboratory study by the Federal Bureau of Mines, in cooperation with the California Division of Mines, of the swelling-type bentonite deposits in the Vallecitos area in San Benito County, Calif. The purpose of the study was to learn if these large deposits contain bentonite of sufficient quality and quantity to be of economic value as an oil-well drilling mud additive. Large amounts of bentonitic clays are used by the petroleum industry as well as the steel industry in California. Additional amounts may be required in the near future as a concrete or earth-fill admixture in constructing dams and canals in the California Central Valley. Depletion of some local clay deposits and loss of others to military installation areas have given new emphasis to the need for developing new bentonite deposits in California.

Jan 1, 1959

By J. B. Gayle

During the past several decades, there has been a steady increase in the number and size of experimental ovens used for carbonization research. Although many were originally intended principally for studies of coal expansion, current practice usually includes determinations of the properties of the experimental cokes. With respect to size and shatter characteristics, the cokes from the larger experimental ovens closely approximate those from duplicate charges carbonized in commercial ovens; however, they are consistently lighter and frequently less resistant to degradation by abrasive forces. To minimize these differences, some operators dry the experimental charges before carbonization. The resulting higher dry coal charge densities do, in fact, yield cokes with gravities closely approximating those produced commercially from the same coal or blend but without drying. The drying of the experimental charges may be criticized on the grounds that it represents a departure from commercial practice and may result in oxidation of the samples; for these reasons, the practice has not been universally adopted.

Jan 1, 1961

By T. Ruff

Researchers at the National Institute for Occupational Safety and Health, Spokane Research Laboratory, studied technology and methods that could reduce accidents involving surface mining equipment that collides with other vehicles or workers, or drives over an unseen road edge. These accidents are partially attributed to the lack of full visibility around these large pieces of equipment. Blind areas can be extensive and this report presents plots of blind areas for five pieces of surface mining equipment. Several technologies designed for detecting obstacles in blind areas and providing a warning to the operator were evaluated on off-highway dump trucks. These proximity warning systems included radar, sonar, GPS, radio transceiver tags, and combinations of radar and cameras. A summary of test results is presented in this report, along with guidance on effective proximity warning technology, installation and maintenance considerations, and recommendations for effective implementation. This study found several commercially available systems that could effectively warn an equipment operator of an impending collision. Several new technologies also show promise for reducing these accidents. In most applications, it is recommended that sensor-based systems be combined with video cameras to provide important alarming functions along with an actual view of the blind area.

Jan 6, 2007

By Robert M. Doerr

Isothermal oxidation kinetics were determined for three grades of Ni and for 99.99 percent Co in Ca and in air from 800° to 1,200° C. The oxidation reactions followed approximately the parabolic rate law. For 99.99 percent Ni in 02 at 1,200° C, the parabolic rate constant was 2 mg cm-2 hr-2. For 99.99 percent Co in dry air, the constant ranged from 1 mg cm-2 hr-2 at 800° C to 18 mg cm-2 hr-2 at 1,200° C; for 99.99 percent Co in 02 the constant was 2 mg cm -2 hr-2 at 800° C and 10 mg cm-2 hr-2 at 1,000° C. For 99 percent Ni in dry air, the constant ranged from 0.2 mg cm 2 hr-2 at 800° C to 3 mg cm 2 hr-2 at 1,200° C. By X-ray diffraction measurements, only divalent oxides were found in the scales. Volumetric and quartz-helix gravimetric methods were used. The volumetric apparatus was designed to permit less stringent restrictions on the corrosion specimens; it was also more convenient to use. The agreement between the weight gain determined gravimetrically and the 02 consumption determined volumetrically was not good enough for direct comparison of gravimetric and volumetric results.

Jan 1, 1963

By O. C. Blade

The use of Diesel fuel as a source of power is continuing to increase in the United States. The latest available figures indicate that refineries are delivering in excess of 10,000,000 barrels of this type of fuel per month. Factors contributing to this increased consumption are conversions by a number of railroads from steam to Diesel locomotives and the growing use of Diesel engines in buses, trucks, tractors, earth-moving machinery, water craft, and stationary power plants. The increasing importance of Diesel fuel has led to a need for more information on its characteristics, particularly on the grades and qualities currently being marketed. To supply this information the American Petroleum Institute and the Bureau of Mines, United States Department of the Interior, under a cooperative agreement, are conducting annual surveys of Diesel fuels produced in refineries in this country. Samples of Diesel fuel were analyzed by the manufacturers in accordance with instructions from the Motor-Fuels Survey Panel of the Automotive Research Committee of the American Petroleum Institute. Results of the analyses were transmitted to the Bureau of Mines where the data were studied am compiled as shown in the tables of this report. The first survey was made in 1950 and was published as a Bureau of Mines report. The present report shows the results of a similar survey made during 1951.

Jan 1, 1951

By P. S. Jacobsen

In 1960 over 93 percent of the coal cleaned mechanically in the United States was cleaned in processes that utilized water or dense-medium suspensions of fine solids in water. Thus, in the process of removing deleterious ash-forming and sulfur-bearing minerals, another deleterious substance--water-- is added to the coal. The subsequent removal of the water from the coal, and the concomitant recovery of the coal from the water, is not troublesome in the sizes coarser than 1/4-inch. In the finer sizes, however, it is a difficult procedure that often costs more than the original washing operation. Because of the importance of liquid-solids separation in coal preparation, the Bureau of Mines has a continuing program of research in this field. The objective is to make available information on the performance characteristics of various types of equipment available for liquid-solids separations, thus promoting the wise selection of equipment for specific applications, and, thereby, more effective processing of coal. Results of work on flocculation as an aid to filtration5 and the sieve bend screen6 have been published. The present investigation of the screw-type classifier operating in combination with the cyclone was undertaken primarily because such classifiers are comparatively new to coal preparation and information on their performance is not available. The cyclone has become well-known since its introduction in this country by the Bureau of Mines in 1948.7 Use of the cyclone in conjunction with the screw-type classifier represents an attempt to provide the maximum recovery of solids at minimum moisture content.

Jan 1, 1962

By J. M. Stuve

Low-temperature heat capacities and the enthalpy of formation were deter-mined calorimetrically by the Bureau of Mines for CuO?CuS04. The derived standard entropy (S°298.15) was 40.36±0.04 cal/deg-mole, and the enthalpy of formation (?H°f) was -219.l±0.3 kcal/g-mole. A large thermal anomaly was observed in the heat capacity of CuO?CuS04 at 20±0.1 K. Gibbs energy of formation data are tabulated up to 1,200 K. Construction details of a precision low-temperature adiabatic calorimeter capable of determining heat capacities of solids in the temperature range 5 to 320 K are given. A calibrated miniature germanium resistance thermometer was incorporated into the calorimeter to extend the range of accurate measurements below 15 K. High-resistance dc heater windings were used throughout the cryostat to reduce heat conduction of inner connecting wires.

Jan 1, 1975

By Lloyd A. Morley

Previous research conducted for the USBM by Penn State personnel (Grant GO-101729) found that a need existed to physically model a typical a-c/d-c coal mine section electrical system. Its purpose would be to permit preliminary evaluations of electrical problem solutions prior to launching full-scale investigations. Such use can result in greater flexibility than afforded by present computer models. Furthermore, numerous problems, which would be virtually impossible to incorporate in a computer model at this time, are more easily analyzed with physical simulation. The development of this system is now proceeding at the USBM's Bruceton Research Facilities. However, electrical specifications of scaled down components for its construction are required. This project is a result of that need and has been funded as an extension to Grant GO-133077. The following report covers these specifications. Scope of Work To represent a mined a-c/d-r. coal mine section, the typical component specifications must detail at least: a. one a-c continuous miner, b. two a-c or d-c shuttle cars, c. one a-c or d-c roof bolter, d. one a-c section fan, and e. feeder cables. Further, each machine should be portrayed by each of its general

Jan 1, 1974

By P. G. Clites

The Bureau of Mines developed techniques for induction melting of titanium in a split, water-cooled copper crucible. Calcium fluoride, which was used as an inert slag cover during melting, formed an insulating layer of solid slag between the ingot and the crucible wall. This thin layer of slag effectively insulated the ingot from the crucible and prevented the molten metal from shorting across the slits between adjacent segments of the crucible. The technique provides a means of melting loose titanium sponge and scrap and eliminates the need for fabricating a consumable electrode. This report describes the equipment developed and compares ingots produced from two varieties of titanium sponge, from titanium scrap, and from previously melted titanium with ingots prepared by vacuum-arc melting and electroslag melting. A melting scheme was also proposed and evaluated whereby loose titanium sponge was consolidated into a first-melt ingot for vacuum-arc remelting.

Jan 1, 1969

By J. N. Geyer

In coal mining it is essential to maintain the roof over working places and roadways in the safest condition possible. To this end every effort should be made to win the coal with the least injury to the immediate roof strata, as broken strata certainly present a greater hazard than a sound roof. The chief causes of injury to the roof in mining are inherent in the method of development and recovery and the blasting practices followed. The first, which may produce severe stresses in the roof, weakening it over comparatively large areas has been discussed in previous papers3 and will not be treated here. The second cause is local in effect, but with the same general method of blasting being employed throughout a mine having uniform roof conditions, similar effects on the roof may be expected. In the Bureau's investigation of accidents caused by falls of roof and coal it has been necessary to make a careful study of blasting practices and their effect on the immediate roof. The purpose of this paper is to show the effect of the observed methods of blasting on different types of roof and to point out methods that have been proved to be least harmful to the roof strata. The data used in preparing this paper have been compiled from reports made by Bureau engineers engaged in the study of falls of roof and coal, and embrace mines opened in the Pittsburgh coal in Ohio and Pennsylvania and the Pittsburgh and Sewickley coals in West Virginia.

Jan 1, 1933

By D. Harrington, W. J. Fene

That fatalities from mine explosions can be very much reduced from the experience of past years if not wholly eliminated was fairly well demonstrated during the fiscal year ended June 30 , 1934 , there being only 28 deaths in the United States from explosions during this period . This is by far the lowest number of fatalities from explosions in the history of coal mining in the United States insofar as records are available . Although the frequency of occurrence of explosions has not decreased greatly during the past 6 years , there has been a marked decrease in severity , indicating that our coal -mining people are taking more effective precautions to prevent the spread of explosions . Pennsylvania is a good example of what may be done in reducing both the frequency and the severity of explosions ; by the adoption of up- to - date safety measures , Pennsylvania bituminous mines now have the enviable record of only one major explosion disaster in more than 5 years , and the one major explosion which did occur cost but 7 lives although 277 persons were exposed ; their lives were saved because rock- dusting prevented the spread of the flame and violence . Many of our other mining States are making definite progress in working mines without disastrous explosions and fires ; some of these , like Alabama , West Virginia , Indiana , Wyoming, and others now operating with few , if any , explosions , have had anything but a favorable record in the past .

Jan 1, 1935

By Oliver C. Ralston

Fluorescence is of growing interest to the mineral industry because certain minerals may be detected thereby and because, as shown in figure 1,4/ many minerals (natural or synthetic) are needed in tubes and lamps. The use of fluorescent lighting is expanding, and large numbers of lamps of many sizes and shapes are being made and used in works, factories, stores, offices, homes, and in photography. Fluorescent tubes, as distinguished from clear tubes filled with neon, argon, or other rare gases through which a current of electricity passes, fluoresce owing to specially, selected and prepared minerals placed in the tubes. Luminous chemicals and paints also contain special minerals and are used in similar applications; therefore, these also will be considered in this report. Although the quantity of minerals (in tons) that are used for fluorescent purposes is small, and probably will continue to be so, this use is significant because it exemplifies a requirement for "pure" minerals in which a trace of contaminant as" minute" as one part in ten million may distinguish between the acceptance or rejection of a particular material. This extreme purity makes synthetic minerals almost essential, and natural mineral's are now little used.

Jan 1, 1944

By H. F. MILLE, Charles A. Kumke

This paper describes mining operations at the Iron King mine of the Shattuck -Denn Mining Corp. in Yavapai County , Ariz . It is one of a series being prepared by the Mining Division of the Bureau of Mines on mining practices and methods in various mining districts of the United States . The mine and surface plant of the Iron King mine are situated in secs . 15 and 21 , T. 13 N. , R. 1 E. , about 20 miles by State highway 69 east by southeast from the city of Prescott and 1 mile southwest of the mining town of Humboldt on the Prescott -Mayer branch of the Atchison , Topeka & Santa Fe Railroad (fig . 1 ) . A l-mile truck haul brings the mill concentrates (lead and zinc ) to bins on a siding of this line at Humboldt ; the silver -gold bullion is handled separately . Some of the oldest residents in the vicinity of Prescott claim that the original location for the Iron King mine was made in 1880. The earliest recorded production was in 1906-1907 . During the first World War the mine produced fluxing ore for the Humboldt smelter . In 1936 the property was purchased under tax sale , and a mill (140-ton capacity ) was erected in 1938. The capacity of this mill was increased to 225 tons the following year , and a cyanide plant was added in 1940 to treat mill tailings . In 1942 the Shattuck -Denn Mining Corp. purchased the property . A new working shaft was sunk , mine development was speeded , and mill capacity was again increased . The predominating locally formation of this district is a pre -Cambrian schist known as Yavapai schist . The Iron King deposit , which carries gold, silver , lead , zinc , and copper , occurs as a series of lenses in a sheared zone of the pre -Cambrian schist . Down to the 600 -foot level the ore was mined and drawn by the shrinkage method . The cut -and -fill method was adopted for the lower levels . Waste rock for stope fill was provided by block-caving an area on the 600 level . Main haulage drifts were driven in the firm footwall , and crosscuts were driven across the mineralized zone at 100 -foot intervals . Grab samples taken from each car of every working place and channel samples cut every 5 feet in development work are considered sufficient for estimating ore reserves .

Jan 1, 1950

By R. V. Higgins

The results of two separate but related studies are given. In the first study, four equations were tested; the object was to determine which would produce a curve that would best fit data points that represent a trend of declining oil production in 90 California fields. Two conventional equations (the Arps and semilog) and two novel equations (extreme-c and double semilog) were tested. The curves were first fitted to the initial 9 years of the 15-year production data and then extrapolated for 6 years to determine how well the extrapolated curve would fit the data points. The generated curves were also extrapolated beyond the last data point to predict rates of future production. The results of the first study showed that no equation was clearly superior to the others in all respects. The semilog equation resulted in the best fit to production data for the first 9 years, but the Arps and extreme-c equations produced a better fit for the extrapolated data for the period of 9 to 15 years. The Arps and extreme-c also gave more realistic production rates when extended to the point where cumulative production equaled reserves. A second study was made to determine if the least-squares technique applied to the Arps equation would result in more accurate extrapolations. The merits of the logarithmic and the nonlogarithmic forms of the Arps hyperbolic equation were also tested. For the logarithmic expression, it was found that one of the constants of the Arps equation reached a value so small or so large that the equation was not applicable to the data of 40 of the 90 California fields. The nonlogarithmic form of the Arps equation was applicable to neither the same 40 fields nor to a few additional ones. When the data and the Arps equation were compatible, the use of the least-squares technique as compared with other methods improved the extrapolation accuracy somewhat.

Jan 1, 1971

By D. G. Foot

The Bureau of Mines investigated energy-efficient methods for recovering potash values from process and waste brines. Laboratory pan evaporation of four chloride brines produced crude salts containing predominantly sylvite, halite, and carnallite. Six sulfate-chloride brines produced crude salts containing primarily schoenite, kainite, leonite, sylvite, carnallite, and halite. Potash grades ranged from 7.2 to 22.2 pct K20, and recoveries from 84 to 99 pct. Sylvite flotation from chloride evaporites, with amine collector, recovered 90 to 97 pct of the potash in a concentrate containing 54.3 to 60.3 pct K20. Fatty acid flotation of the high-sulfate evaporite recovered 78 pct of the sulfate minerals in a 27.8-pct-K20 concentrate. Flotation of the chloride minerals with amine collector recovered 80 pct of the potash in a 59.7-pct-K20 concentrate. Solar evaporation of 10,000 gal of brine recovered 99 pct of the potash in a crude evaporite containing 24.5 pct schoenite and 20 pct sylvite. Continuous flotation in a 100-lb/h process research unit recovered over 95 pct of the potash in schoenite and sylvite concentrates containing 28.0 and 62.3 pct K20, respectively. An economic evaluation suggested a rate of return of 3 pct for a new facility and 9 pct if. the process is adapted to fit an existing plant.

Jan 1, 1984

By J. H. Soulé

"The Copper King copper-gold-silver deposit was discovered about 1880. Various individuals and companies have been interested in the deposit and considerable work has been done, although production, if any, has been small. The deposit is located in the western part of Laramie County Wyo., and is favorably nituated with respect to rail and truck transportation and high-tension power facilities.Mild summers and cold winters characterize the climate. Precipitation averages between 16 and 17 inches annually, with considerable snowfall in the winter. Permanent streams are small and most available water in being stored for use by Cheyenne, Wyo. Range grasses comprise the bulk of the vegetation, with small treed and shrubs common in the most rugged areas.The deposits lie upon land owned by Wyoming, now leased by a group of Wyoming and Colorado businessman constituting the Copper King Mining Co.Primary copper-gold mineralization seems largely confined to an equigranular, relatively fine grained gneiss that is part of a pre-Cambrian complex of metamorphic rocks ranging from schists to pegmatites. The copper minerals are oxidized to a depth of from 100 to 150 feet, with the occasional occurrence of secondary minerals at greater depths. The copper minerals chalcopyrite, malachite, chalcocite, bornite, cuprite(?), and some native copper were observed in Le deposit.In addition to the 4,030 feet of diamond-core drilling in 11 holes done on the deposit by private companies, the Bureau of Mines drilled 3 holes for a total of 2,630 feet. The sample results of this drilling plus available data from previous drilling and sampling are appended to this report."

Jun 1, 1955

By B. C. Parks

This paper is a report on the relationships between petrographic composition, chemical composition, physical properties, and thermal behavior of banded bituminous coal. It describes the relationships between petrographic composition, behavior in various laboratory tests, and carbonizing properties of different petrographic types of coal that occur in relatively thick benches in a single bed of high-volatile A bituminous coal - the Hernshaw bed of Boone County, W. Va. Thin-section microscopic analysis and free-swelling index determinations of the thin-section samples were made of a standard column sample. A standard face sample, a representative channel sample, and representative samples of two prominent petrographic benches of bright and dull coal were subjected to chemical analyses and free-swelling-index, plasticity, dilation, agglutinating, low-temperature carbonization, and BM-AGA retort tests. A float-and-sink separation was also made of part of the standard face sample. The fractions from this gravity separation were subjected to petrographic and chemical analysis and free-swelling-index, plasticity, and dilatation tests.

Jan 1, 1959