Search Documents

By T. Belem

The main objective of this study is to better understand the effect of underground CPB placement conditions on its microstructural, hydro-mechanical and geochemical properties. To reach this objective, three PVC columns, each 3 m high, were built, and were filled with CPB material. The columns allow simulating undrained (UD), half-drained (HD) and fully-drained (FD) conditions along with the measurement of resulting self-weight consolidation settlement of the CPB. Bleed and drainage waters were also collected from each column for geochemical analyses (pH, Eh, EC, SO42- content). After 90-days of curing time, a total of sixty CPB samples were cored from the backfill columns and subjected to uniaxial compression tests followed by physical characterization (Gs, void ratio, water content, degree of saturation, specific surface area). The results showed that the total drainage water and the maximum observed settlement occur mainly within the first 72 hours after the columns are filled. The corresponding volumetric strains suggest that in situ backfilled stopes simulated behave in a similar way to the fully-drained (FD) or the half-drained (HD) conditions. The MIP test results show that the pore structure varies between the top and the bottom of each column.

May 1, 2007

By A. Azad

SAGD (Steam Assisted Gravity Drainage) is an in-situ oil recovery technique for heavy oil reservoirs. The technique has been successfully applied to many projects in the past 25 years and the process has been, now, well understood. It is now believed that geomechanics plays an important role in SAGD and should be considered in numerical or analytical modeling. Currently, geomechanics is numerically modeled through combining a multi-phase flow and a geomechanical simulator. Numerical modeling is, however, time consuming, need lots of input data, and could not be used for quick decision-making purposes. To decrease the modeling time, this study based on a new version of the Reis drainage model, proposes coupled mathematical model and reserves the effect of geomechanics in the process. Results showed a perfect match with the past experimental and numerical data.

May 1, 2009

By Sunil Koppalkar, Liming Huang

"Since late 1980s the research group led by late Professor Andre Robert Laplante at McGill University undertook fundamental studies and applied research of the Knelson Concentrator (KC) and developed a sustainable method to correctly estimate gravity recoverable gold (GRG). In the early time a concept of ‘free gold’ was used, it was defined as the gold that could be separated and recovered from gold ore by amalgamation. Due to health and safety hazards, its practical use had declined. Around 1994, a methodology using a 3-in Knelson Concentrator to measure gravity recoverable gold was established at McGill University. Through more than 10 years’ improvement and optimization, this technique had become a standard method to evaluate GRG for gold ores, gold plant streams and platinum group metals. Until 2006, about 200 GRG tests had been carried out at McGill University for the ores from all over the world. Recently, a modified version of GRG test (short test) with the advantages of reduced processing time and lower cost had been developed for the mundane needs of gold industry.INTRODUCTIONGold gravity recovery has evolved significantly over the past twenty-five years, mainly because of the advent of the Knelson Concentrator (Knelson 1988, 1990, 1992, Laplante 2000). Now, a series of Knelson Concentrators for different applications are manufactured and used in gold industry all over the world (Knelson Concentrators 2004).In 1980s the Knelson Concentrator gained acceptance from mining industry as an effective device for the recovery of gold from grinding circuit. Knelson Concentrator became the obvious choice because of its design features: a relatively long processing time without concentrate discharge (compared to some other centrifuges, such as Falcon Concentrator and Chinese Yunxi Centrifuge at that time), large throughput capacity, treating a wide size range of material, yielding a high grade concentrate with small mass that could easily be smelted. As more and more Knelson Concentrators were accepted in gold industry, mineral processing engineers faced with challenges: what are the separation mechanisms of the Knelson Concentrator? How much gold can be extracted for an ore if a Knelson Concentrator is installed? For answering these questions, a laboratory scale Knelson Concentrator was created."

Jan 1, 2007

By Bernard Jones

LTUG ? A meeting of many mining companies that are using large tires ? Introduction of the mines and size ? Companies go over their usage of tires and performance ? As a group we discuss how the manufactures are doing with supplies and performance (who's running what sizes and manufactures they are using) ? The mine's best practices they use (which ones work for them and which ones don't) ? Where the mines see themselves going in the future ? What type of tire management the mines have in place

May 1, 2009

By L. S. Urbanoski

This presentation describes a major modernization project at the Geco concentrator. The objectives of the program were to replace obsolete flotation equipment and upgrade process controls.Noranda Minerals Inc. — Gecc Division is located at Manitouwadge in Northern Ontario. The community is situated north of Lake Superior approximately equidistant from Thunder Bay and Sault Ste. Marie.Milling operations began in September, 1957. The mill processes a complex base metal ore by differential flotation techniques to produce copper, lead and zinc concentrates. To date some 43 million tons have been milled, qualifying Geco as a rather major base metal deposit.II. BACKGROUND:The Geco concentrator was designed and constructed in the mid 50's. A number of features specific to a concentrator of that vintage provided the justification for the modernization efforts described herein.Firstly, the mill was constructed without any instrumentation, not even pneumatic controls. Solid state electronics, computers and related instrumentation were unheard of, or rather primitive by today's standards.Secondly, some of the major equipment, in particular the flotation equipment, did not compare favourably to that in use today. MacIntosh flotation machines (more commonly known as Mac cells) were installed at Geco. These cells were prevalent in a number of concentrators built by Noranda, including Quemont Mining Corporation Limited, Gaspe Copper Mines Limited and Noranda — Horne Division. The Mac cells were used for copper and zinc rougher and scavenger operations. Some units were also installed for a pyrite recovery circuit that was never operated. In total, 104 Mac cells were installed in the main flotation area of the concentrator.

Jan 1, 1987

By Dayang Datu Khalil, Charle Amoah, Fred Kock

Abosso Goldfields Limited has been optimizing the comminution circuit at the Damang Mine Operation for the treatment of 100% primary ore. The optimization process started at a base rate of 343 tph when treating primary crushed primary ore, and was increased to above 600 tph with partially crushed primary ore. Abosso Goldfields engaged Orway Mineral Consultants (OMC) to assist with the optimization process in 2009 and the two companies have been working together since, to further refine the process. Continuous improvement was achieved through crushing circuit modifications, changes in operating processes and grinding control system utilization. This paper discusses the improvements developed for the increase in milling capacity and improvements in final product size.

Jan 1, 2012

By W. J. Witte, M. K. Witte

"The purpose of this report is to present a generalized preliminary design and cost estimates for a typical heap leach operation such as might be undertaken in Northern Ontario. This report should be of value to anyone in the mining industry planning, or contemplating, a heap leaching operation in Ontario, either on a large or small scale. While more detailed costing and design work will obviously be required for each specific project being contemplated, the data provided in this report should enable parties to make preliminary estimates of the costs of proposed projects and should identify most of the planning and design parameters that will need to be considered.Although heap leaching has been used extensively as a low cost gold recovery method in other parts of the world for many years, it has only recently become of interest to the Canadian mining industry.In order to investigate and demonstrate the feasibility of using heap leaching in Ontario, the Ontario Ministry of Natural Resources in 1982, undertook to locate a private sector proponent willing to undertake a 10,000 ton demonstration project. This project was to have been carried out at a production scale under normal northern Ontario field conditions. The Ministry was to have provided technical management and design for the designated project."

Jan 1, 1985

By M. Cai

A practical simple method is proposed to estimate the tensile strength (st) of strong brittle rocks from the strength ratio of R= sc/st = 8 sc/sci, where sc is the uniaxial compressive strength and sci is the crack initiation stress in an uniaxial compression test. 8 is the Griffith strength ratio and the term sc/sci accounts for the difference of crack growth or propagation in tension and compression in uniaxial compression tests. sci can be reliably obtained from volumetric strain measurement or acoustic emission (AE) monitoring. With the strength ratio R determined, the tensile strength can be indirectly obtained from the result of uniaxial compression tests. In addition, a practical estimate of the Hoek-Brown strength parameter mi is presented and it is suggested that mi = 12 sc/sci can be applied to strong, brittle rocks in high confinement zone and mi = 8 sc/sci can be applied to low confinement to tension zones. It is found that the predicted tensile strengths and Hoek-Brown strength parameter mi using this method are in good agreement with test data. The rock strength parameters like st and mi, which require specialty tests such as direct tensile (or Brazilian) and triaxial compression tests for their determination, can be reasonably estimated from uniaxial compression tests.

May 1, 2009

By Richard Frentress, Dave Donelon, Robert Henderson, Mike Warnert

"The Round Mountain gold mine is an open-pit mining operation located 97 kilometres north of Tonopah in Nye County, Nevada. Gold has been produced from the property since 1906.Gold is currently recovered using a combination of four independent processing operations. These include a 10,000 ton per day mill, a 30,000 ton per day, crushed ore heap leach, a 150,000 ton per day, run-of-mine ore heap leach and a small high-grade gravity concentration circuit. In 2002, Round Mountain Gold Corporation produced 755,494 troy ounces of gold at a total direct operating cost of US$2.14 per ton ($193/oz).This paper presents a summary of the Round Mountain operations and discusses some of the processing innovations that have enabled the mine to profitably recover gold from a large low-grade ore body.INTRODUCTIONRound Mountain Gold Corporation is a 50/50 joint venture between Kinross Gold Corporation and Barrick Gold Corporation. Kinross acquired its ownership interest in the Round Mountain mine upon completion of combination with Echo Bay on January 31, 2003. The joint venture partners continue to support an aggressive exploration program in the vicinity of the mine in order to add reserves and extend the mine life.The Round Mountain mine currently operates a conventional open pit that is approximately 8,200 feet long, 4,900 feet wide and 980 feet deep. Mining is conducted on 34-metre benches by electric shovels and front-end loaders paired with 150, 190 and 240-ton haul trucks. Blasthole samples are collected and assayed and provide the control for ore segregation. Based upon these assays, blasted pit rock is determined to be run-of-mine Dedicated Pad ore, crushed Reusable Pad ore, high-grade ore or waste.Gold is recovered using a combination of four independent processing operations. These include run-of-mine ore heap leaching (Dedicated Pad), crushed ore heap leaching (Reusable Pad), milling and the gravity concentration circuit. Non-mineralised rock is delivered directly to the waste dumps. Low-grade ore is trucked directly to the Dedicated Pad and medium-grade ore is crushed and placed on the Reusable Pad. High-grade ore is handled in one of three ways: 1) leached on the Reusable Pad and offloaded to the mill; 2) sent directly to the gravity plant with tails reporting to the mill; or 3) sent directly to the mill or mill stockpile. The gold particle size distribution of highgrade ore determines the processing method."

Jan 1, 2005

By Y. Okita

The Goro Nickel Process, developed over a ten-year period, uses a number of novel processing steps and treats two ore types, limonite and saprolite, together. Nickel and cobalt are solubilized using a 270°C pressure acid leach in sulphuric acid, which rejects the bulk of the Fe into the leach residue as hematite particles. The leach liquor, after CCD, is aerated to oxidize any ferrous iron to the ferric form and is neutralized with limestone to precipitate iron as hydroxides together with gypsum from the neutralization of the free acid. Further neutralization with lime, together with steps to remove suspended solids, reduces the iron to trace concentrations. Nickel and cobalt are directly recovered from the low-iron leach solution by primary solvent extraction using Cyanex 301® (SXl) in a high-strength hydrochloric acid solution. Nickel is subsequently separated from cobalt in a secondary solvent extraction circuit using tri-isooctylamine. A granular nickel oxide is made by pyrohydrolysis, and this allows the recycling of hydrochloric acid to SXl. The process is currently being commercialized to produce approximately 60,000 t/y of nickel as nickel oxide granules and approximately 5,400 t/y of cobalt as cobalt carbonate. This paper describes the process development to control the Fe concentration in the SX1 feed solution.

Jan 1, 2006

By R. D. Brown

The Federal Government's White Paper on Tax Reform received further major criticism in the reports of the Committees of the House of Commons and the Senate, which recently completed a lengthy review including public hearings of the government's proposals. These reports both criticized the emphasis placed by the White Paper on its concept of tax equity rather than on a system which would promote economic growth. However, the Finance Committee of the House of Commons was prepared to accept, with modifications, a number of the White Paper's key reform proposals. The Senate Finance Committee was more critical of the basic thrust of the tax reform program and recommended that a modification of the existing tax system would be more appropriate to Canada's needs. Both Committees re-commended a more favourable treatment of mining income than that originally proposed in the White Paper, and to some extent both Committees suggested proposals that were even more favourable to the industry than those set out in Finance Minister Benson's amended proposals made in August of this year. This article out-lines the principal recommendations and comments in the reports of both the House of Commons Committee and the Senate Finance Committee.

Jan 1, 1971

By Sami Hindstrom, Travis Orser, John Starkey

"A great deal of effort has been expended in the last 11 years by the authors and others to identify the correct power required to grind ore in a SAG mill, by developing ore hardness variability functions for the ore body to be mined. This paper describes the next step in the SAG design process, which is choosing a SAG mill to accomplish the required specified design performance.At the test work stage, each ore hardness data point is a unique and discreet bit of information that represents the energy required to grind the ore represented by that sample at optimum SAG conditions. When the design criteria are set, it is now considered necessary that the required power draw in the mill chosen be provided at optimum conditions as well.Based on actual 3-ft diameter pilot plant results, we can now show that the grinding efficiency and throughput drop when the optimum load limit is exceeded. Future work is expected to show a similar reduction in efficiency when exceeding optimum speed. Providing specified power by exceeding these optimum conditions is not adequate and leads to a lower cost but underperforming SAG mill.It is possible in some cases to modify a SAG circuit to force it to perform better, but this often takes time, much effort and costly modifications. In most cases the capital spent on a properly sized SAG mill may prevent production losses that would be many times greater over the extended start up period. This is the direct result of choosing the proper SAG mill at the start.INTRODUCTIONThe sequential steps required for the design of any grinding circuit, have changed dramatically in the last seven years. Previously, it was considered necessary to do six foot diameter SAG mill pilot plant tests on representative samples of minus six inch ore (F80), in order to understand design requirements. It can now be shown that this method is costly and not likely to produce the desired result because it is difficult to recover six-inch material from deep within a new mine. The representative nature of the sample is often compromised when the sample is selected."

Jan 1, 2003

By G. B. Hudson

Previous papers (1, 2) pertaining to the treatment of uranium-bearing ores were concerned with the flotation of the radioactive minerals. In this investigation, the application of flotation to the removal of acid-consuming minerals from uranium ores was considered. Two pitchblende-bearing ores, which, because of the presence if dolomite were abnormally high acid consumers, were studied. In both in-stances commercial reagents of widely varying fatty acid composition proved satisfactory as flotation col-lectors, particularly at a pH of 10.5, for the carbonate minerals. From an economic viewpoint, however, Neo-Fat 42-12 was favoured. A mixture of sodium tripolyphosphate and citric acid was an effective depressant for the pitchblende in the ores. The tailings remaining after the removal of the dolomite by flotation contained, in one case, 88.5 per cent of the uranium in the original sample, and, in the other, 93.8 per cent. Analyses conducted on these tailings and on the original ores showed that

Jan 1, 1963

The information in this document has been prepared as at February 16, 2011. Certain statements contained in this document constitute ?forward-looking statements? within the meaning of the United States Private Securities Litigation Reform Act of 1995 and forward looking information under the provisions of Canadian provincial securities laws. When used in this document, the words ?anticipate?, ?expect?, ?estimate?, ?forecast?, ?will?, ?planned?, and similar expressions are intended to identify forward-looking statements or information. Such statements include without limitation: statements regarding timing and amounts of capital expenditures and other assumptions; estimates of future reserves, resources, mineral production, optimization efforts and sales; estimates of mine life; estimates of future internal rates of return, mining costs, cash costs, minesite costs and other expenses; estimates of future capital expenditures and other cash needs, and expectations as to the funding thereof; statements and information as to the projected development of certain ore deposits, including estimates of exploration, development and production and other capital costs, and estimates of the timing of such exploration, development and production or decisions with respect to such exploration, development and production; estimates of reserves and resources, and statements and information regarding anticipated future exploration; the anticipated timing of events with respect to the Company's minesites and statements and information regarding the sufficiency of the Company's cash resources. Such statements and information reflect the Company's views as at the date of this document and are subject to certain risks, uncertainties and assumptions, and undue reliance should not be placed on such statements and information. Many factors, known and unknown could cause the actual results to be materially different from those expressed or implied by such forward looking statements and information. Such risks include, but are not limited to: the volatility of prices of gold and other metals; uncertainty of mineral reserves, mineral resources, mineral grades and mineral recovery estimates; uncertainty of future production, capital expenditures, and other costs; currency fluctuations; financing of additional capital requirements; cost of exploration and development programs; mining risks; community protests; risks associated with foreign operations; governmental and environmental regulation; the volatility of the Company's stock price; and risks associated with the Company's byproduct metal derivative strategies. For a more detailed discussion of such risks and other factors that may affect the Company?s ability to achieve the expectations set forth in the forwardlooking statements contained in this document, see the Company's Annual Report on Form 20-F for the year ended December 31, 2009, as well as the Company's other filings with the Canadian Securities Administrators and the U.S. Securities and Exchange Commission. The Company does not intend, and does not assume any obligation, to update these forward-looking statements and information. Marc Legault, a Qualified Person and the Company?s Vice-President, Project Development, reviewed the technical information disclosed herein. For a detailed breakdown of the Company?s reserve and resource position see the February 16, 2011 press release on the Company?s website. That press release also lists the Qualified Persons for each project.

May 1, 2011

By W. Leblanc, J. Phalen

This paper tells the story of a serious mine fire on a mechanized longwall face in a submarine coal mine at Glace Bay, Nova Scotia. The story gives, in chronological order, a technical account of the steps taken to investigate, fight and contain the fire. The time during which the events took place spans from June 19 to November 7, 1975.

Jan 1, 1976

By L. Flett, S. Woods, C. Deredin

"Following a significant reduction in world Imperial Smelting Furnace (ISF) capacity from 2003 to 2008, a major optimization initiative was successfully carried out on the lead upgrading and bulk (zinclead) flotation circuits in the Brunswick Concentrator.This paper describes the process improvements that have taken place in order to reduce the quantity of bulk concentrate:•,Increase in lead upgrading rougher flotation circuit capacity•,Installation of a closed-circuit bulk regrind utilizing MillPebs and 150 mm Cavex hydrocyclones•,Installation of two additional cleaner flotation stages on the bulk circuit•,Optimization of the manipulated variables in the lead upgrading and bulk circuitsINTRODUCTIONThe Brunswick Mine (Xstrata Zinc Canada) is located near Bathurst, New Brunswick and is one of the world’s largest lead/zinc mines. Milling of ore commenced in 1964 from the No. 12 orebody, with an expansion in 1966 to accommodate ore from the No. 6 open pit mine. The planned closure of the mine will take place at the end of the first quarter in 2013. The ore is a complex massive sulphide, consisting of approximately 20% valuable minerals, 60% pyrite and 20% silicates.A simplified flowsheet for the concentrator is given in Figure 1. The overall flowsheet involves SAG milling, secondary ball milling, selective flotation, and dewatering by thickening, filtering and drying. The complexity of the flowsheet evolves from the requirements for fine grinding and the production of four concentrates: zinc (sphalerite), lead (galena), copper (chalcopyrite) and bulk (sphalerite plus galena).Primary hydrocyclone overflow feeds the copper-lead aerator-roughers for flotation at pH 9.0 with soda ash. Plant xanthate (80-20 sodium isopropyl and potassium amyl) and AP407 are used as collectors in the copper-lead circuit. The rougher concentrate is directed to the copper-lead regrind circuit and the tailings are fed to the secondary grinding circuit. The secondary hydrocyclone overflow from the secondary grinding circuit feeds the copper-lead rougher-scavenger banks. Rougher concentrates are reground to a P80 of 28 µm prior to three stages of copper-lead cleaning. The first stage of cleaning is done in an open circuit with the tail reporting to the cleaner scavenger. The cleaner scavenger concentrate reports to the regrind circuit and the cleaner scavenger tail combines with the rougher/scavenger tail to feed the zinc circuit. The second and third stages of cleaning are performed in closed circuit with the cleaner tail being recycled to the copper-lead regrind circuit. The average final concentrate grades 23% Pb, 3% Cu and 704 g/t Ag, and is fed to the copper separation circuit."

Jan 1, 2013

By Ish Grewal

"Batch centrifugal gravity concentrators, which produce very high ratios of concentration, have become common place for recovering free gold within milling circuits. Their effectiveness has proven to be especially useful in recovering finer gold particles. The knowledge related to testing, modeling and scale-up of these systems has been well established over the recent decade mostly due to the efforts of the late Dr. Andre Laplante.Gravity separation technologies such as jigs, spirals and shaking tables can provide the increased mass yields required for minerals that occur at higher concentrations than gold, however their effectiveness tends to diminish at finer particle sizes. The development of high mass yield centrifugal concentrators has provided the opportunity to be able to recover a wide range of minerals at finer particle size classes when compared to the more traditional gravity concentration devices. These concentrators also provide additional benefits such as smaller unit footprint and automated operation.This paper discusses the background, current practices and future applications for high mass yield centrifugal concentrators in base metals, sulfides and industrial minerals. Bench scale, pilot scale and plant practice examples are also presented.INTRODUCTIONGravity concentration, one of the oldest mineral beneficiation processes, has evolved over the decades and continues to play an important role in modern mineral processing operations. The development and growth of froth flotation in the early part of the twentieth century led to a decline in the importance of gravity concentration. However, gravity concentration continued to be used for ores that are difficult to beneficiate using froth flotation; such as tin, tungsten, niobium/tantalum, iron, industrial minerals and oxidized coal. In recent decades, many operations have begun to employ a combination of both gravity concentration and froth flotation Since flotation relies on surface chemistry and gravity concentration relies on specific gravity differences, putting these techniques in series provides today’s metallurgist with unprecedented opportunities to maximize grade and recovery of many of these minerals."

Jan 1, 2009

By James F. Archibald

Research has been conducted for the Workplace Safety and Insurance Board of Ontario (WSIB) to characterize thin, spray-on lining materials (TSLs), as well as combinations of TSLs and conventional spray supports, and to assess their capacity for inhibiting damage created by mining-induced rockbursts. This study has been performed to assess the capabilities of such support systems for preventing rock and support material damage that often results due to rockbursting. A variety of TSLs and other spray support media were subjected to the effects of simulated rockbursting, through use of explosive detonation trials, to evaluate their damage mitigation capacity. Results have validated that TSLs and variant layer combinations may be as effective as or better than conventional support materials for mitigating rockburst or like damage in highly stressed mine environments. In civil engineering construction, and typically in underground tunneling operations where concrete linings are applied, liner deterioration is a continuing and pervasive problem that often requires expensive and time-consuming rehabilitation effort. The ability of TSLs to provide effective concrete structural reinforcement while providing sustainable resistance against underground or restricted environmental hazards, as with fires or dynamic failure events, may permit wider use of TSLs than is currently foreseen by the mining industry. Significant benefits for use of TSL materials in concrete liner rehabilitation and for concrete material protection have been assessed.

May 1, 2006

By Mostafa Benzaazoua

Les remblais en pâte cimentés sont de plus en plus utilisés dans les exploitations minières souterraines. Une autre alternative d?utilisation du remblai en pâte consiste à le pomper et à le stocker dans des empilements de surface. En plus d?avoir des avantages d?un point de vue de stabilité physique des ouvrages, le remblai en pâte cimenté en surface permettrait également de stabiliser les contaminants dans la matrice du remblai à l?aide du processus de solidification et de stabilisation. Dans cette étude, des remblais en pâte constitués d?un résidu minier sulfuré renfermant beaucoup d?arsenic et de différents liants ont été testés afin d?évaluer la stabilisation des contaminants dans la matrice de remblai. La méthode utilisée pour évaluer la stabilisation et la solidification des contaminants est le test de lixiviation en extracteur de Soxhlet. Les résultats géochimiques issus de ces essais ainsi que la caractérisation chimico-minéralogique des remblais lixiviés ont été analysés pour comprendre les phénomènes chimiques présents dans les remblais durant le temps de cure. Les résultats obtenus montrent que les sulfures présents dans les remblais étudiés (pyrite FeS2 et arsénopyrite FeAsS) s?oxydent et provoquent la dissolution des hydrates les plus vulnérables (dissolution de la portlandite Ca(OH)2 et/ou décalcification des gels CSH). Le calcium produit permet de précipiter les sulfates (essentiellement sous forme de gypse plus ou moins hydraté) et l?arsenic sous forme d?arséniates de calcium plus stables. Les différents liants utilisés donnent des résultats différents en termes de stabilisation et de solidification qui seront discutés dans cet article.

Nov 1, 2002

By C. Pelley, S. Kelebek, G. Kunzel, S. Gregersen, M. Pollanen

A series of small-scale tests was conducted to evaluate the effect of micro-fracture development, imposed by blasting, on the material properties of the rock as well as its resistance to crushing and grinding. The uniaxial compressive strength, tensile strength, Poisson’s ratio, Pwave, S-wave velocity, point load test index, crushing, and grinding work indices were evaluated for samples without any blasting load and for samples which had received a variety of blast loads ranging from a single impact with a lowstrength detonating cord to a combination of impacts at different times and significant impacts with powder factors close to those used in practical blasts. It was shown that the rock mechanics parameters change even at low impacts, suggesting easier crushing of the rock. Damage values appear to be affected by timing as stress wave superposition affects the damage process. Fragmentation is achieved at higher impact levels while work index modification of the fragments is also observed when high powder factors are used, suggesting improvements in grinding.

Jan 1, 2006