Search Documents

By M. Oliazadeh, A. Vazirizadeh

"The inclusion of small amounts of silicon, phosphorus and sulphur in iron ores or concentrates can have a profound effect on the steel making process and thus on the final iron and steel products. In nature however, it is inevitable that iron deposits contain unwanted elements. Each element has its own distinct effect on the final steel product. The effect of high silicon is the formation of gray iron. Phosphorus mainly increases hardness and strength, lowers solidus temperature and increases fluidity and cold shortness. Finally sulphur contamination causes cracks in the iron texture when smelting and forms white iron when casting. Overall, the acceptable level of phosphorus, sulphur and silica in the iron concentrate should be less than 0.04%, 0.15 % and 1.5 % respectively.Scarcity of high grade iron ores necessitates using lower grade ores with higher amounts of impurities. The purpose of iron concentrators is to increase iron grades to an appropriate level suitable for steel making as well as removing impurities. Although many impurities can be traced in the ore, the most predominant impurities are limited to one or two elements. In this paper the beneficiation methods for removing SiO2, P and S are presented, including flotation, and the parameters that need to be considered in the design of beneficiation plants are discussed. Finally industrial cases are discussed along with their metallurgical performance.INTRODUCTIONIn metal sector, value of iron ores and concentrates is determined by iron percentage as well ascontent of:• Useful elements (Mn, Ni, Cr, V, Ti): natural alloying elements in steel• Deleterious impurities (S, P, As, Zn, Pb, K, Na): impair metal properties or complicate operational process in blast furnace• Fluxing components (Si, Ca, Mg,, Al)Sulphur and copper result in red-short, phosphorus is the cause of cold brittleness and arsenic and copper decrease welding characteristics. Sulphur should not exceed 0.15 in commercial ore. Acceptable sulphur content in ores and concentrates for producing sinter and pellets is 0.6%max, as sintering and heat hardening of pellets remove sulphur 60-90%. Phosphorous content in ores, sinter and pellets is limited to 0.07%-0.15%. 0.00.1% As max, 0.1-0.2% Zn max and up to 0.2% Cu are allowed in iron-ore part of the blast furnace burden for the production of standard conversion pig iron. Slag-forming components are divided into basic oxides (Ca, Mg) and acidic (Si, Al). Higher ratios of basic to acidic oxides are preferred since this reduces raw fluxing material."

Jan 1, 2016

By D. A. Akinlade, N. L. Richards, D. C. Murray, W. F. Caley

To investigate the effect of adding Ti to a Ni-Cr-Fe powder metallurgy alloy, a thermodynamic software package was used to predict the phase transformations that occurred during thermal processing. Specifically, the effect of adding 3w/o Ti to a 6w/o Al modified ternary Ni-Cr-Fe alloy (the quaternary) was simulated and the phase transformations that might occur in the material on sintering were obtained using the thermodynamic modeling tool. These predictions were subsequently compared with experimental results obtained by X-ray diffraction and metallography. For comparison, selected compacts were prepared containing only the ternary + 3w/o Ti (no Al). Based upon compressibility curves, the optimum pressure for producing the new Ti compacts was 500 MPa vs 600 MPa for the quaternary composition with Ti. In each case, hardness of the base alloy was enhanced by the Ti addition whereas the residual porosity remained relatively constant at about 19%. Finally, although SEM/EDS failed to confirm the presence of Ti in the gamma prime intermetallic, XRD spectra showed a shift in lattice parameter on addition of Ti, suggesting that the intermetallic was of the form Ni3(Al,Ti).

Jan 1, 2010

By Mory M. Ghomshei

"The cost of deep underground mine cooling depends on a number of geological, environmental and economic factors such as the temperature gradient in the mine, the outside air temperature, and the local price of energy. While geological factors, being static, can be controlled to some extent during the mine design, the environmental and economic factors dynamically change and therefore can only be controlled through a flexible mine ventilation system.With an average temperature gradient of 20–25°C/km, the virgin rock temperature at 2,000 m can reach 45–60°C. Conventional cooling at such depths could lead to exorbitantly high costs. In-mine geothermal heat pumps can considerably reduce the cost of cooling through energy communication with the centralized absorption chillers, which service the mine from the surface.It is shown that in-mine heat pump systems can be a viable option for reducing operating expenses and providing some degree of flexibility to cope with fluctuating energy costs. The price of Natural gas and electrify are the most important variables for optimizing the level of interaction between the surface and inmine cooling systems. Deep mine waters can be used to carry a portion of the mine heat to the surface, where the heat from mine can be used as a supplementary energy source for absorption chillers. As an extra benefit, the heat output of the chillers can be used for district heating and or greenhouse growing.The case of cooling deep levels of deep mines in Sudbury Canada (e.g. Creighton Mine) has been discussed. It is shown that an initial 1MW in-mine geothermal heat pump system can save significantly on the cost of cooling. Such a demonstration project will allow R&D on viability of larger similar systems to be incrementally added in the future.INTRODUCTIONThe amount of heat generated in deep and ultra-deep mines depend primarily on the regional temperature gradient and the thermal conductivity of mine rocks. The conductive heat flow is quantifiable and can be minimized or optimized in the process of mine design. Another important heat source can be related to underground equipment such as diesel machinery which often have low efficiencies (approximately 25–35%). This heat source can be controlled and reduced though improving efficiencies or using electrical equipment, which offer a much better efficiency (approximately 80–90%). Mine waters can also be a significant heat source (convectively bringing large amounts of heat into the mine workings)."

Jan 1, 2019

By John H. Schloen

"The object of this paper is to review electrolytic copper refining as it was in 1954(1), as it is now in 1984, and to comment on the many improvements which have been made in the last thirty years.In 1954, and even in 1984, the ASTM specification B 115 for cathode copper was 99.90% minimum copper plus silver content and 100% minimum electrical conductivity, IACS standard. However, to meet competition and to satisfy the requirements of the fabricators and the electrical industry, the electrolytic refinery must supply a product of 99.95% to 99.96% minimum copper content, and 101fJlo minimum electrical conductivity.The range of cathode impurities reported by 20 major copper refineries in 1954 are given in Table I.The much more rigid British Specification, DD 78, for high-purity cathode copper, specifies individual elements, as well as groups of elements, as shown in Table 2.The Svenska test has been replaced by a similar procedure which uses 2.r mm diameter wire. The ISO test is the one listed in the DD 78 specification. In Table 3, corresponding values for the Svenska and ISO test s are given for various wire bar coppers."

Jan 1, 1986

By L. Xu, A. Vazirnegad, R. Bhaskar

"Respirable dust samples are collected by the U.S. Mine Safety and Health Administration (MSHA) and mine operators as part of the requirements of the Federal Coal Mine Health and Safety Act of 1969. About 1.85 million respirable dust samples collected by MSHA were analyzed for the period 197/ to 1990 f or the states of Alabama, Colorado, Illinois, Kentucky, Ohio, Pennsylvania, Utah, Virginia, and West Virginia. Trends in coal dust exposure of continuous miner operators, helpers, and roof bolters were analyzed. The reported production in each of the nine states was analyzed. The relationship between average dust exposure and coal production was evaluated. In addition, the differences between mine operator and MSHA inspector collected data were examined for each state. The average exposure levels for the three occupations - miner operator, miner helper, and roof bolter were also compared.The data indicate that the dust exposure levels have significantly dropped over the last twenty years, while at the same time production has increased, attesting to the ability of the U.S. mining industry to adapt successfully to the stringent dust control regulations. In terms of coal production, it appears that some states, such as Utah, Illinois, and Kentucky, were able to increase their production significantly relative to others, such as Pennsylvania and Virginia. The relationship between dust concentration and coal production is, at best, tenuous. 11 implies that existing dust control technology has assisted several mine operators to meet dust standards, while, at the same time, enabling mines to produce more coal than before. Comparison of data collected by MSHA and mine operators indicate that MSHA inspectors recorded higher dust levels and lower shift production relative to mine operators."

Jan 1, 1993

By C. John Sullivan

Is there a relationship among the Sudbury nickel ores, the Cobalt deposits, and the Huronian, Athabascan and North Australian uranium provinces? All are within intracratonic basins, with ore near basal unconformities. There are similarities in the geochemical "fingerprints" pointing to basic igneous rock affiliations. Some show a time relationship to basic igneous activity and to great rift systems. Many basic dykes show radioactivity at their edges. A spatial relationship between the uranium-cobalt-nickel ore at Midwest Lake, Athabasca, and basic igneous rock is reported. These remarks are not meant to imply, necessarily, a direct genetic connection between the basic dykes, etc., and the ore. In some cases, the relationship may be similar to that noted between basic and ultrabasic intrusives and volcanic massive sulphide ore deposits. Crustal thinning in these areas, associated with graben, appears to have favoured volcanic activity, as well as basic intrusives. Probably, the potential of the Huronian should be re thought . Athabascan-type ore may be present . New data on mineralization in Turner Township, Ontario, suggest this. The mineral possibilities of other basins should be reconsidered. It is to be remembered that the Athabascan and Kombolgie basins were neglected for many years. Intracratonic sedimentary-igneous basins contain many of the greatest mineral fields of the world.

Jan 1, 1979

By Robert D. Brown, Robert B. Parsons

"Careful tax planning and proper attention to the regulations can result in an optimum deduction ""of the 25% federal resource allowance. Introduced in the Income Tax Act in1976, in part to compensate for the disallowance of provincial mining taxes and royalties. the 25% ""resource allowance"" is a permitted deduction in computing taxable income from mining and petroleum. However, the rules relating to the deduction are complex, and the importance of the deduction which can readily exceed 25% of net income- is frequently underestimated. This month, Tax Notes discusses the basic rules of calculating the resource allowance, and suggests some tax planning aspects which may warrant consideration.May 6, 1974 - "" .. . our provinces have adjusted royalties, mining taxes and other arrangements to derive what they perceive to be a fair share for the benefit of their people. However, a provincial resource is also a national resource... I am proposing that revenues derived by provincial governments in respect of production from a… mineral resource should no longer be.\ deductible in computing the income of the operator. .. I am proposing that. .. there be an extra abatement from federal income tax in respect of taxable production income.. .fifteen points in the case of mineral profits. .. "" - The Honourable John N. Turner, Minister of Finance. June 23, 1975-"" '"" to meet, at least in part, the request for some form of deductibility in the tax system for provincial resource levies... to offer more incentive to those who explore and develop in Canada. .. I am now proposing, the extra fifteen point abatement of federal taxes would be withdrawn... at the same time, I am introducing a new resource allowance, which would be an extra deduction from income equal to 250/0 of production income.. ."" - The Honourable John N. Turner, Minister of Finance."

Jan 1, 1980

By Y. Kocaefe, D. Bhattacharyay, D. Kocaefe

The carbon anodes used in the electrolytic production of aluminum are made of petroleum coke, recycled anodes and butts, and coal tar pitch. Due to technological advances in the aluminum production technology, aimed at increasing production and decreasing energy consumption and greenhouse gas emissions, better quality anodes are required. Presently, the anode quality is evaluated by visual inspection and the analysis of a small core taken from 1.5-2% of the anodes produced. The visual inspection is susceptible to human error and limited to surface imperfections. The analysis of cores takes time, and therefore, it is difficult to determine the existence of a problem and intervene at the right time. In addition, the core does not represent the whole anode due to the non-homogeneity of anodes. A validated online anode quality control system can highly improve the situation. In this article, an electrical resistivity measurement method developed for this purpose is presented.

Jan 1, 2014

Adaptive processing is often related to the mineral composition of the mining block currently processed. The portions of waste, ore and secondary product minerals considered are always positive and typically sum to 100% (i.e. a composition). A typical solution to predict block averages of spatially dependent quantities would be block kriging. However, kriging is based on spatial correlations and it has been repeatedly shown that correlations of compositional data are spurious and blurred by the constant sum constraint. Aitchison (1982) proposed a general solution for compositional problems, based on transforming the compositional data to a set of logarithms of ratios of components, and analysing the transformed scores. The transform is chosen to be invertible to ensure that no information is lost in the process. This methodology avoids spurious correlation problems and ensures coherence between results obtained with different subcompositions. Pawlowsky-Glahn and Olea (2004) adapted the approach for point-support geostatistics, allowing the prediction of point compositions from spatially neighbouring data, without the artefacts induced by standard multivariate cokriging. Unfortunately upscaling the results of this approach with block cokriging is not straightforward, because of the nonlinearity of logratio transforms. Furthermore, we have to consider those nonlinearities created by the dependence on the block composition of extraction efficiency and processing costs of the possible processing choices. This paper proposes a solution for predicting the conditional expectations of the benefit of processing the block with each processing choice using geostatistical simulations of the local values of the composition and the resulting block integrals. The computation for a large number of blocks can be done efficiently using Cholesky decomposition. The approach also allows the calculation of prediction errors for expected compositions and expected benefit at almost no additional computational cost. Such compositional approach is necessary, for example when processing choices depend on proportions of certain minerals after other components have been removed; or if processing alters the composition in a multiplicative way, by partially removing a portion of some components.

Aug 1, 2013

By Harold S. King

TWO summers ago I had the privilege of visiting No. 18 colliery at Glace Bay. Underground, we travelled along the haulage-way behind a powerful electric locomotive. The motor in this locomotive began to smoke badly and a carbon tetrachloride type of extinguisher was used several times during the trip. At the time, I noted a strong odour of phosgene. On my return to Sydney, I spoke to Mr. Harold Gordon, Assistant to the General Manager of the Dominion Steel and Coal Corporation, and warned him of the danger of using this type of fire extinguisher in confined spaces, since it is a well known chemical fact that phosgene, a dangerously toxic gas, is formed by the decomposition of carbon tetrachloride. This danger does not seem to be widely recognized, so it seems advisable that a more general warning be published. Attention was first drawn to the danger by the death of two men in the United States Navy Department subsequent to breathing fumes from carbon tetrachloride used in a fire, and when an employee of the Bureau of Mines also was overcome while fighting a fire with carbon tetrachloride liquid. These accidents led to an investigation of the decomposition products of carbon tetrachloride by a group of workers in the Research Laboratory of the Pittsburgh Experimental Station, U.S. Bureau of Mines, the results of which were published in the October, 1920, number of the Journal of the .Franklin Institute (1). Their experiments were conducted by two methods. The first consisted in applying the liquids to actual fires and -to hot metal in a closed room of 1,000 feet capacity, where the gaseous products, mixed with air, could be retained and analyzed. The second method was to pass the vapour:s in air through heated tubes of iron or quartz, where the humidity of the air and the temperature could be controlled.

Jan 1, 1939

By Cy Jordan, Ben Burdett, Adrian Dance, Jack Rainey

"In 1997, EIMCO Minerals installed a knowledge-based control system on one of the five primary grinding lines at Highland Valley Copper. The objective of the system is to maximise throughput without affecting circuit product size or flotation recovery. The system was commissioned in October 1997 on a SAG mill/ball mill circuit following a plant audit and upgrade of the control instrumentation.The system monitors and controls the SAG mill power, bearing pressure and recycle load by manipulating the solids feedrate, water addition and mill speed. The two ball mill and cyclone circuits are controlled through water addition at various points in the circuit as well as the number of operating cyclones.An on-line particle size analyser is used to measure the cyclone overflow quality. Models of the SAG mill charge level and overflow product size are also incorporated. A method of predicting the SAG mill power response to feedrate changes is used to lessen the effect of dead time for improved mill power control. In the future, inferred measurements of SAG feed particle size and hardness will allow changes in ore behaviour to be predicted and compensated for by the system.This paper describes the development of the project -from installation and commissioning to modifications and refinement -along with prospects for the future.BackgroundIn early 1997, EIMCO Minerals was contracted by Highland Valley Copper to install a knowledge-based or expert system control strategy on one of the five grinding lines in the mill. This was to become the start of the Advanced Control Project at Highland Valley Copper (HVC). This paper will review the progress of the Project as well as discuss the prospects for the future.Following a preliminary engineering study (or plant audit) by EIMCO in 1996, it was decided to implement an advanced control system in order to improve plant operations and increase productivity. The study suggested that such a system had a pay-back period of a few months through increased throughput without loss in flotation recovery. Highland Valley already had successfully applied higher level control through their Elsag Bailey distributed control system (DCS) and this was the next stage in process optimisation."

Jan 1, 1998

By D. H. Wilson

"This paper examines the increasing need for mechanical-electrical people within the industry and some of the reasons why such a shortfall exists. It is suggested that, in part, it is image related. The present industry-education relationship in addressing the situation is examined and some thoughts are expressed on how these may be built on, in order to help solve the problem of attracting people to this critical area.IntroductionAs a long-time proponent of plant engineering and maintenance as a management function, I would like to review the progress made by the industry/ educational approaches in satisfying the needs in that area. In doing so, I would like to make the following points:1) that there has been an accelerating shortfall of mechanical-electrical people relative to the needs of the industry;2) that the condition will probably get worse before it gets better; ,3) that the past industry I educational approaches to alleviate the problem have met with limited success; and finally4) I would like to review some of the things being done and consider how these efforts might be extended."

Jan 1, 1981

By M. Sukhram

This paper presents a technique to determine the direction of velocity in liquid aluminum (Al) by measuring the temperature distribution within a cylindrical rod while it is inserted into the flow. The heating pattern of the rod is a result of the interaction of the thermal fields of the rod with the liquid Al. This interaction freezes aluminum onto the cylinder in a characteristic pattern and as a result the temperature response within the rod also follows a distinctive heating pattern. Monitoring the temperature within the cylindrical rod as a function of spatial and temporal coordinates, the direction of velocity can be inferred. Experimental research work involving liquid Al was conducted at the University of Toronto using the Revolving Liquid Metal Tank (RLMT). The RLMT is a resistance furnace which can hold up to 50kg of liquid Al. In this RLMT tangential velocities up to 0.35m1s can be generated. Experimental data for different superheat and magnitude of velocity demonstrate that the sensor records different heating patterns under different fluid flow conditions. Using the transient temperature information, the direction of velocity of the molten Al flow field can be detected.

Jan 1, 2011

By A. Haque

"This paper describes an improved formulation of an analytical shear strength model developed by Haque & Kodikara (2012) by incorporating the failure of regular concrete/rock joints subjected to CNS condition. Sokolovskii’s analytical solutions developed for failure stress of slopes have been found to be effective in this regard. The analytical models have been validated for predicting the shear behaviour of concrete/rock joints subjected to various CNS loading conditions. The model has been found to accurately predict the dilation, normal stress and shear stress behaviour for a regular triangular saw-tooth joint up to the peak shear stress. Moreover, the peak shear stresses of concrete-rock joints with asperity angles ranging from 5 to 27.5o compared reasonably well with the available laboratory test results.INTRODUCTIONA new shear strength model for elastic regular triangular concrete/rock joints loaded under Constant Normal Stiffness (CNS) boundary condition has been developed by Haque & Kodikara (2012). The salient feature of this model is its capability of accurately estimating the normal and shear stresses of joints with shear displacements under CNS condition by incorporating the elastic deformation of asperities. However, the shear strength model of Haque & Kodikara (2012) for the elastic asperities cannot be directly employed to predict the peak shear stress of a joint experiencing plasticity under applied loads. Therefore, the model inevitability requires articulation of an appropriate shear failure criterion simulating the boundary conditions of the loaded asperity to predict the peak shear stress and corresponding normal stress and dilation behaviour of concrete/rock joints. Sokolovskii (1960) developed a set of analytical solutions for failure stress of slopes comprising c-??soils, which can be exploited effectively to simulate the failure condition as encountered for loaded regular triangular concrete/rock joints (Seidel & Haberfield, 2002)."

Jan 1, 2015

By B. A. Watters, G. A. Parslow, F. H. Mcdougall

Carbonate-rich rocks occur at several localities within the Flin Flon volcanic sequence of the eastern Amisk Lake area. The rocks occur in two areas: as a group of small occurrences on islands within Amisk Lake and as two much larger linear belts running parallel to the regional structure east of Amisk Lake. Mineralogically, the rocks consist of talc and Ca-poor ankerite with occasional graphite. Segregation of these minerals and colour variation impart a well-defined planar fabric to the rocks and where the units are fairly continuous (e.g. Mosher Lake), their trend and attitude suggests a concordant relationship to the volcanics. Major and trace analysis of22 samples confirms the presence of two types, with one type being represented in each of the two areas. Most of the elements studied can be used to characterize the two groups, but three elements in particular give a clear separation: Mg, AI and Ni. Recalculation of the major element analyses, on a water and carbonate-f ree basis, indicates that one group (large concordant bodies with high MgO, high Ni and low AI20.J is altered ultrabasic material of peridotitic or dunitic composition. Because no relict igneous material is observed, and the contacts are apparently very sharp, it is possible that the hydration-carbonization process occurred simultaneously with intrusion, .in a closed system. The other group (small occurrences with relatively low MgO, low Ni and high AI203J represents alteration of basaltic rocks. AIthough some analyses suggest the introduction of calcium, as carbonate, along with the volatiles, the major oxides have remained remarkably stable during the alteration process(es).

Jan 1, 1981

By H. Langlois

"Included in the Mines Gaspe mining complex located at Murdochville, Quebec, is a copper smelter which comprises a reverberator furnace, two Peirce-Smith converters, an anode furance, and a sulphuric acid plant.The 50% smelter capacity available is supple mentedby custom concentrates for treatment. As these concentrates can be varied and extremely complex many modifications and improvements have been brought about to optimize and make the process more flexible since its inauguration in 1955.IntroductionThe copper smelter of the Mines Gaspe mining complex is located in Murdochville, a small municipality in the heart of the Gaspe peninsula, 90 km northwest of the town of Gaspe .This metallurgical installation has a daily smelting capacity of 650 tonnes of concentrate and an output of 250 tonnes of copper and 900 tonnes of sulphuric acid. Its main components are: a reverberatory furnace, two Peirce-Smith converters, one rotary anode furnace and one acid plant. The gases, which are produced by the converters, are treated at the acid plant then combined with gases from the reverberatory furnace before being vented through a 152 metre high stack .From the beginning of its operation until the present day (1991), the smelter has treated 7 million tonnes of concentrate and 100 thousand tonnes of scrap for a production of 1.8 million tonnes of copper and 2.2 million tonnes of sulphuric acid."

Jan 1, 1993

By P. Homola, M. Karlík, M. Slámová

"Aluminum sheets (AA1199, AA8006, and AA5754) were processed by accumulative roll-bonding (ARB) in the temperature range from 20 to 350°C. The microstructure of the sheets was characterized by means of scanning and transmission electron microscopy and electron backscattered diffraction. Mechanical properties were monitored by hardness measurements and tensile tests. Increasing strain (number of ARB cycles) led to incremental development of lamellar microstructure with a decrease of the spacing between high-angle grain boundaries in the normal direction of sheets. ARB process produced an important increase of strength while maintaining thickness and relatively high ductility, without accenting of the anisotropy of mechanical properties of sheets. The level of hardening decreased with the processing temperature and at 300 and 350°C ARB caused even the softening of the material due to the recovery of the deformed microstructure or partial recrystallization during heating to ARB processing temperature.INTRODUCTION Accumulative Roll Bonding (ARB) is a technique of grain refinement by severe plastic deformation (SPD) proposed by Saito et al. (1999). One ARB cycle consists in sheet cutting, surface treatment, stacking of two pieces, heating (optional), and rolling with 50% reduction in thickness. Since the sheet thickness remains unchanged by this cycle, ARB processing can be repeated as many times as desired. The goal of ARB is to impose an extremely high plastic strain on the material, resulting in structural refinement and strength increase without changing specimen dimensions. After several cycles, ultra-fine grained (UFG) materials with high strength and relatively high ductility are produced. An advantage of this method is that it does not require any special equipment as other SPD methods such as equal channel angular pressing (ECAP) (Valiev & Langdon, 2006), high pressure torsion (HPT) (Valiev et al., 2000), or cyclic extrusion and compression (CEC) (Richert et al., 1999), but only a conventional rolling mill and so it is seen as an economically viable and industrially scalable processing route. ARB processing has been successfully applied to various kinds of metallic materials at room or elevated temperatures (Tsuji, 2005). Besides processing single metals and alloys, ARB has also been used for creating ultra-fine grained and nanograined metallic composites (Wu et al., 2010; Qu et al., 2014)."

Jan 1, 2018

By S. V. Burr

"IntroductionOne of the more puzzling geological enigmas, in the writer's opinion, is how rock can move sideways with respect to other rock. In the writer's study of regional northwest-southeast folding in North America (Burr, 1980), he may have found the answer to horizontal offset.Horizontal OffsetSideways movement or horizontal offset does not mean that the movement was, or is, horizontal. As indicated below, the actual movement may be at a high angle from the horizontal. However, it is the horizontal VECTOR, or offset, which is measured on surface by geologists. Vertical movements (thrust, normal, reverse) can be understood, as they involve blocks of rock , generally separated on four to six sides, which have been pushed up or subsided. Vertical faulting across dipping strata can produce APPARENT horizontal offsets. However, this thesis deals only with ACTUAL offsets.The ProblemFigure 1 is a plan view of a simple hypothetical horizontal offset. Three vertical dykes are intersected by a fault lineament. Two dykes exhibit no movement; the middle dyke has been offset a distance (a). Vertical faulting would have produced no horizontal offset. How can a horizontal distance (a) disappear or appear? Rock expands or contracts in infinitesimal amounts.SolutionThe map (Burr, 1980) shows the writer's interpretation of regional northwest-trending folds in Ontario. The writer made two observations about horizontal offsets during his thirty year study of these folds:1) All major horizontal fault lineaments strike at a high angle to the northwest fold axes. Many of the northwest-trending lineaments are fault s, but their movement is essentially vertical.2) Close to many of the known horizontal offsets (and several lineaments), there are areas where plunge reversals are so frequent and close together it is impossible to draw in all the fold axes at a scale of 1 inch = 4 miles, and, in the highly faulted Espanola area southwest of Sudbury, Ontario, all the indicated folds cannot be easily separated at a scale of 1 inch = 1 mile. The writer has observed folds less than 30 feet apart next to the strong Puskitamica-Chibougamau fault in northern Quebec."

Jan 1, 1982

By P. E. Auger, J. E. Gill

"The zinc deposits to be described are in Lemieux township a few miles south of the Tabletop mountains, in the central part of Gaspe peninsula, Quebec. Although they have not been worked, they constitute a potential source of zinc and lead and structurally are of considerable interest.GENERAL CHARACTER OF THE OCCURRENCEThe deposits are in sharp-walled quartz-carbonate veins and breccia zones carrying locally, and in varying amounts, sphalerite, galena, pyrite, marcasite, chalcopyrite, and specularite. Those so far investigated strike generally north-south, have steep dips, and cut through sediments of Lower Devonian age, mostly calcareous argillites or siltstones. Wall-rock alteration is negligible.BROADER STRUCTURAL FEATURESThe principal known occurrences are in the south-central part of a dome structure measuring 6 by 5 miles. The argillaceous sediments are overlain, on the flanks of the dome, by sandstones and lavas. These have been stripped from the central part of the dome, revealing the veins in the argillites beneath. The veins formed after the volcanics, but the fractures and breccia zones in which the deposits formed are confined mainly to the argillite series, presumably because of the greater strength of the lavas.The argillite series is cut by dykes, sills, and small stocks of diorite and acidic 'porphyries' that are older than the veins.THE FEDERAL HILL AREAThe distribution of known veins is shown in Fig. 1. The characteristic features of the veins are well illustrated by the Federal Hill area shown in Figs. 2, 3, and 4, and described below."

Jan 1, 1954

By A. J. Rigby

Computer generated, actual-scale furnace models have been imported into a rendering software application to provide for impressively realistic surface features and lighting. When these models are imported into a 3D engine framework, it is possible to create content-rich virtual environments allowing for complete interactivity and could provide for a powerful tool to conceptualize refractory lining designs. This technology has been applied to illustrate the optimized design concept of an anode-refining vessel, which can be expected to be completely relined in six days and to last for 4-5 years with minimal partial relining. This technology could easily be applied to other smelter furnace, converter and refining vessel designs.

Jan 1, 2007