Search Documents

By P. C. Lighthall, D. W. Zandee, W. Shukin

"IntroductionThis chapter deals with the on land disposal and storage of fine tailing in slurry form behind dams. Other types of tailing, such as coarse dry cobbs from magnetic separation of iron ores and other dry materials, have special problems and are not addressed in this paper. The disposal of mine waste is not included, except as such materials may be of value in the construction activities related to tailing disposal.In earlier North American mining, mines were smaller and frequently disposed of their tailing by direct discharge into neighbouring streams or bodies of water. Where that was not practical or not permitted, the solids were collected in tailing ponds and only the effluent liquids were released or decanted. The dams used for these early impoundments were fragile structures and failures were common. With the advent of large, low-grade open pit mines, and increasing awareness of environmental and safety considerations, recently established mines have carefully-designed tailing disposal systems, with wellconstructed dams and attention given to protection of the environment. Older mines are being improved or at least being examined critically with a view to upgrading as necessary to meet the new standards.Modern tailing disposal systems are highly variable and unique to each mine. Tailing pond selection and design is dependent on available topography as also is the design of transport and water reclaim systems. Suitable sites that are at higher elevations than the mills or distant from them may require that the tailings be pumped. Dams, either earth or rock structures built of the most convenient and economic material, are usually a suitable mix of local borrow, mine waste and coarse tailings. The most economic structures are those built mostly of coarse tailing."

Jan 1, 1989

By S. Shimaya, T. Maejima, M. Shimo

"The authors conducted the in-situ gas-tightness tests in a fractured rock at the Namikata underground LPG storage site in Ehime prefecture, Japan. The test consisted of two independent setups, a gas-tightness test that used boreholes, and a chamber-scale test that used a horizontal drift sealed with a concrete plug. In each test, the gas pressure was increased up to the onset of the measurable gas flow to obtain the maximum containment pressure. This paper discusses the hydraulic conditions for gas leakage initiation and the importance of the pore pressure measurement for monitoring the gas-tightness of the LPG storage cavern based on the test results.INTRODUCTIONJapanese first underground LPG storage plant was constructed by JOGMEC, the Japan Oil, Gas and Metals National Corporation, at Namikata in Ehime prefecture in granitic rocks (Kato et al., 2007). The “hydraulic sealing principle” (Åberg, 1977) that utilizes groundwater flow into an unlined cavern to prevent the leakage of gas through fractures in the surrounding rock mass was employed for storage of LPG. This paper describes the results of the in-situ tests performed at the Namikata Site to obtain information on fundamental gas-tightness characteristics of fractured rock. Two types of in-situ tests, a borehole gas-tightness test and a chamber gas-tightness test, were carried out near the storage caverns. Figure 1 shows the cavern layout of the Namikata underground storage plant and the test locations. The storage facilities consist of three caverns (W26m×H30m×L485m). The cavern crown lies at a depth of 150m below the sea level in Cretaceous granitic rock (Figure 1). Water curtain boreholes excavated from the water gallery tunnel at EL-125m level are located above and side of the caverns to prevent water drainage from fractures during the construction stage as well as during operation. The borehole tests were performed from a drilling adit excavated from the eastern end water gallery tunnel, while the chamber test was conducted at the southern edge of an exploratory drift extending from the central water gallery tunnel."

Jan 1, 2015

By Mark Sherman, M. Dennis, Raj Rajamani

"The two Alumbrera 36ft (10.97m)dia. SAG mills were sized, using the FDW ""Grindpower 'I program, to treat an average of 1852 tph each. This paper describes how modelling of the shell lifter design, using the Millsoft program, identified milling inefficiencies caused by poor charge motion. This explained the ""as built"" circuit's inability to achieve the throughput rates predcted by the circuit's designer. Use of the Millsoft program to design a new, dramatically different lifter configuration, in conjunction with a different approach to variable speed drive utilization, has resulted in an improved charge motion and a 30% increase in hard ore milling rates. The new lifter design has allowed the designer's predicted average throughput rates to be achieved.IntroductionThe Alumbrera project grinding circuit consists of two 36ft dia. X 17ft EGL, 13 500 kW, variable speed, gearless drive SAG mills coupled to four 20ft dia. X 30ft EGL, 6 000 kW fixed speed, gear driven, ball mills. The circuit is configured as two identical grinding aisles, each consisting of one SAG mill and two ball mills. No pebble crushing circuit was installed due to the expected absence of a critical size fraction in the first years of production. However, the grinding circuit layout does incorporate space for a pebble crushing retrofit. At present, only about 5% - 10% of the new mill feed reports as trommel oversize and is recycled back to each SAG mill using a water cannon.The circuit was designed to be ball mill limited and to treat the four major Alumbrera ore types at rates varying between 68 000 tpd, and 89 750 tpd, depending on ore hardness. Average throughput rate, and hence nominal design rate, for the grinding circuit was 80 000 tpd (1 852tph per line at 90% availability)."

Jan 1, 1999

By C. O’Hara, S. Roy, K. Swedburg, J. Katchen

"New Gold Inc.’s New Afton concentrator commenced operation in June 2012, producing a copper-gold-silver concentrate. During the first two years of operation, various optimization efforts have improved mill throughput, recoveries and concentrate grade. Daily mill throughput has increased 20% above the design rate. This was achieved through more consistent instantaneous feed rate and size distribution from the mine reclaim stockpile, higher pebble crusher reliability, changes to the SAG and ball mill grinding media sizes, larger SAG grate openings, reduced SAG discharge screen-deck aperture size and an increase in the maximum ball mill power draw limit. Metal recoveries at New Afton are primarily limited by liberation in the coarser size fractions; therefore, improving the grind size at a given mill throughput has been the main means of improving recovery. The average rougher flotation feed F80 size was reduced from 175µm in Q1 2013 to 165µm in Q1 2014, while the average operating mill throughput increased by 25%. Other flotation circuit changes focusing on recovery improvement include the addition of froth crowders to the rougher cells and the use of a stronger frother. The average concentrate grade increased from 22% Cu in Q1 2013 to 25% Cu in Q1 2014. This was achieved by redirecting the flash flotation concentrate stream to the regrind circuit and by the addition of lime to the cleaner circuit.This paper describes the above improvements made at the New Afton mill. The paper describes the objectives, timing and end result of each area of improvement.IntroductionThe New Afton Mine is situated approximately 10km west of Kamloops, British Columbia, 340km north-east of Vancouver. The mine has a moderate climate, access to transportation and electrical infrastructure, nearby fresh water supply, and close proximity to industrial and mining service businesses. The population of Kamloops is around 90,000 with most mine employees living in or around the city."

Jan 1, 2015

By D. S. Hines

The purchase of mechanical equipment for mines is not unlike the purchase of other materials or supplies in general principle, but on account of the major part such equipment plays in the operations, and of the fact that life and valuable property are at stake, the matter demands the most careful attention on the part of the purchaser. The problems and difficulties encountered are dealt with below in their sequence in the purchasing procedure. Requisiting Although it is quite a common practice to submit a tentative specification of requirements to recognized manufacturers of equipment- soliciting alternative propositions or recommendations for study in the selection of certain equipment-as a rule the first step in purchasing procedure is the requisition. Primarily, it is the form that carries to the purchasing department the record of equipment wanted. A full and complete description or specification, and accuracy of record, are the important points to be insisted on in a requisition. Too much attention cannot be given to this detail, as this is one of 'the most important phases of purchasing work. Incomplete information, either in specification or detail, leads to delay in handling the requisition, and, if not detected in the purchasing department, may mean receipt of material which cannot be used for the purpose intended. In addition to description of material or equipment to be ordered, the requisition should also show where or what the equipment is for, whether for operating or new work. If for capital account, the number of the authority for expenditure should be given for record and distribution purposes.

Jan 1, 1930

By Marc C. Bétournay

Hydrogen fuelcells are a known technology, having been applied to stationary (e.g equipment, buildings, power plants) and vehicle applications (e.g transit buses, space shuttles). There is currently a growing need to provide alternate power systems to diesel fuel for underground mining vehicles to improve underground air quality and reduce production costs and green house gas emissions. To date, however, fuelcells have not been exposed to underground mine air and physical conditions. A testing program was carried out to provide information on the vulnerabilities of fuelcells as part of a number of proof-of-concept projects to apply hydrogen power to underground mining vehicles. The fuelcell type of choice for the industry, the Proton Exchange Membrane, would function at the range of temperatures encountered in underground and surface operations, and use hydrogen that is stored under low pressure and risk. A small fuelcell stack was tested in a cooperative project between CANMET, the Fuelcell Propulsion Institute, INCO, the Ontario Ministry of Labour, Sandia National laboratories and H-Power. This article will review the tests carried out to measure the effects from high humidity, mineral dust, diesel emission gasses and diesel particulate matter as well as from shock and vibration provided to the unit in underground conditions, at INCO?s 175 Orebody minesite and INCO?s Stobie Mine. The test results provided will show that the unit was not affected by the underground conditions: physically and electrically the unit performed without any reduction in operation or adverse effects imposed.

May 1, 2003

By T. W. Wlodek

"AbstractThe results of research into the fatigue properties of SAE 1080 carbon steel and nickel-chromium-molylbdenum steel for mining drill rods are analysed and described in detail.The effect of water corrosion on the fatigue strength of drill rods of these two steels in the as-rolled condition has ,been investigated and the beneficial influence of shot-peening on their dry and water-corrosion fatigue strengths determined by employing the method developed previously (1).Eight S-N curves for as-rolled and shot-peened mining drill rods under both dry and water corrosion conditions have been derived and their shape and relative position are discussed. The main features relating to field performance of the drill rods are analysed.Purpose of Research and Outline of ProgrammeDRILLING holes in rock and ore by means of drill rods attached to a pneumatic drill is a basic procedure required in mining operations. Detonation of explosives placed in these holes is at present the only practical method of breaking down the rock and ore.A drilling rod is supported by its bit end in the drilled rock. Its shank end, fixed in the drilling machine, transmits impact energy to the cutting edges of the bit. On the field performance of the drill rod depend a number of basic mining operations such as sinking, drifting, and stoping. The drill rod is there-fore regarded as one of the most important tools used in the mining industry."

Jan 1, 1952

The stability of paste fill bulkheads forms an integral part of a successful paste fill system. Bulkheads are constructed at the draw points of open stopes to contain paste fill while the initial pour cures and forms a consolidated plug. Mobilization of uncured paste fill as a result of a bulkhead failure can lead to significant consequences, including endangering the safety of personnel, property damage and production losses and delays. The loading conditions in the paste fill and the resultant lateral loads on the bulkheads are complex and are dependent on many factors. This paper presents a case study of several paste fill bulkhead failures; the results of an in-situ pressure monitoring program to ascertain the pressure loads, and the subsequent paste fill bulkhead evaluation.

May 1, 2007

By C. H. Stockwell

RICE LAKE-BERESFORD LAKE area, situated 100 miles northeast of Winnipeg (Figure 1), is Manitoba's foremost gold mining district, although it is exceeded in gold production in the Province by the Flin Flon base-metal mining district. At present, the area is producing at the rate of about one and three-quarter million dollars annually, almost entirely from the San Antonio and Gunnar mines. The total production to date is about $14,000,000. Of this total, over $7,000,000 has come from the San Antonio mine, over $2,000,000 from the Gunnar mine, about $4,000,000 from the Central Manitoba mine, and the balance from several smaller properties. The writer has led Geological Survey parties in the area for the past four summers. The present paper gives a summary of the results of this work and also includes the findings of C. S. Lord, who was in charge of a party for one year. Much valuable information was obtained from earlier published reports on the area and from officials of mining companies, to whom the writer is indebted for their kindly co-operation. It is impossible in this short paper to give proper credit to the earlier workers or to discuss certain points o disagreement between their conclusions and those presented here. For further information the following references may be consulted.

Jan 1, 1940

By Kevan Ford, Getulio Junior, Rob Henderson, Wayne Philips, Chris Martin, Rob Thorpe

"Plant 2 at the Kinross Paracatu gold operation in Minas Gerais State, Brazil, was commissioned in late 2008. Designed to be the largest tonnage, lowest grade gold milling operation in the world, Plant 2’s throughput has steadily increased towards its design capacity of 5087 tons per hour.The plant employs a gold-specific flotation scheme to recover the majority of gold, which is present as discrete free gold particles. Additional gold is recovered by jigs in the grinding circuit, and the jig concentrates are reground, upgraded and subjected to intensive cyanide leaching. The flotation cleaner concentrate is reground and leached using a conventional CIL circuit.One year after start-up, with the plant stabilizing operationally, plant circuit surveys were completed by a joint team from Kinross Paracatu and Blue Coast Metallurgy Ltd. The surveys audited the flotation and concentrate treatment circuits to investigate the metallurgical performance.This paper describes the Plant 2 operation and how the surveys were designed and executed. Some of the quality control systems that were employed to provide meaningful data from such a low grade gold ore are described and findings and actions taken to improve metallurgy as a consequence of the surveys are discussed.INTRODUCTIONThe Paracatu mine is located two kilometres north of the city of Paracatu, in the north western portion of the state of Minas Gerais, Brazil, 230 km southeast of the national capital Brasília (shown in Figure 1). The present day Paracatu mining operation, fully owned by Kinross Gold, through its Brazilian subsidiary Rio Paracatu Mineração (RPM) is designed to be the largest tonnage, lowest grade free milling gold operation in the world.The deposit currently hosts some 1.2 billion tonnes of ore at a grade of ~0.41 g/t gold, hence contains a total gold reserve of over 20 million ounces. At a designed plant throughput rate of 61 Mt/year the mine life goes beyond 2030."

Jan 1, 2011

By A. G. Eccles

"INTRODUCTIONWestern Mines' copper-lead-zinc operations are located in Strathcona Provincial Park, near the geographic centre of Vancouver Island. This park includes Buttle Lake, which flows into the Campbell River water system. The latter provides domestic water for the Town of Campbell River, approximately fifty-eight miles from the mine site.Operation of the concentrator commenced in December 1966, at which time the tailings were discharged into a small tailings pond near the plant. On May 8, 1967 Permit No. 185 was granted to the company, allowing discharge of the tailings, through a submerged outfall, to the bottom of Buttle Lake.Needless to say, the concept of operating a mine within a park, and the discharge of tailings into Buttle Lake generated considerable controversy. However, this has all but been eliminated over the years by the proven effectiveness of Western Mines' pollution control program. In 1973 this program was further upgraded with the addition of an alkaline chlorination plant. Effluent treatment by this method became necessary as a result of process modifications, and has been effective in maintaining the levels of characteristics in the tailings within the ever increasing pollution control requirements imposed on the industry."

Jan 1, 1977

By D. M. Muir

Many plants produce iron(II)/(III) waste liquors which must be treated by neutralisation and precipitation to remove the iron. Iron can be precipitated as crystalline goethite or jarosite by controlled oxidation at low pH and as magnetite by controlled oxidation at high pH, but only at elevated temperatures (>70°C). This study focuses on the characterisation and settling properties of the iron oxides produced at ambient temperatures using various neutralising agents in order to improve the performance of thickeners. It was found that two-stage addition of caustic to FeC12 solutions produced a fast settling material characterised by Mossbauer spectroscopy and XRD as maghemite and magnetite. However, lime and magnesia additions resulted in more ferrihydrite formation and much lower settling rates because of the enhanced oxidation of Fe(II) by air. Settling rates decreased significantly as the proportion of Fe(III) to Fe(II) in the liquor increased. The mechanism of iron oxide precipitation is discussed together with some reasons for the different behaviour of the neutralising agents.

Jan 1, 2006

By Toshiharu Teranishi

When we apply the Au nanoparticle superlattices to the future nanooptical and nanoelectronic devices, the control of not only the particle size but also the interparticle spacing and symmetry of superlattice are the essential problems to be overcome. First, we developed a novel synthetic procedure to precisely control the particle size of alkanethiol-protected Au nanoparticles in the range from 1.5 to 9.7 nm by the heat-treatment of the small Au nanoparticles in the solid state. Absorption and nonlinear optical properties of alkanethiol-protected Au nanoparticle superlattices were then elucidated. On the other hand, the hexagonal close-packed (hcp) 2D superlattices of small Au nanoparticles with the interparticle spacings from 1.9 to 3.6 nm were successfully prepared by using newly-synthesized ligand for single electron tunneling devices. Finally, various symmetric superlattices, such as chain (2-fold), quasi-honeycomb (3-fold), square (4-fold), etc., of Au nanoparticles could be produced by making use of interligand interactions or some templates.

Oct 1, 2003

By C. E. Baltzer

This paper highlights the electric power situation in Canada, and introduces brief explanation of the salient differences between electrical practice in the United States and Canada. The availability of bask energy in the two countries is touched on, also the hydro versus thermal outlook as applying to Canada. De-v2lopment of thermal-electric power is dealt with in some detail, followed by Canada's thermal-electric power requirements, present and future. The fuel requirements for steam-electric generating plant are assessed on the basis of a survey recently made, and the location and size of the major thermal plant operations are given. Fuel contractual obligations on the part ?of suppliers and consumers are mentioned. Finally, an opinion is expressed in regard to the types of f.uel in ?demand on a regional basis with emphasis on the need for coal in the several areas dealt with.

Jan 1, 1958

By J. C. Loretto

"OPENING REMARKS Yesterday and today we have heard some very interesting papers on operating matters and some of you are probably wondering what we are now doing talking about Communications in Plant Design. Let me tell you! Before the techniques we have heard being discussed can be used, there has to be a properly operating plant. It is certainly a fact that many mineral processing plants achieve only limited success and a number of them can even be said to be failures. Some of you sitting here are probably living with operating problems that are clue to errors in the design.If the histories of these problem plants are examined, it will be found that in many cases, the necessary skills were available during the period of the plant design. There was extensive operating know¬ledge together with a full range of project expertise. Why then the failures? In a substantial number of cases it can be traced to the old, old problem of communications. As plants get bigger, money costs more and smooth startups become more important, it becomes less and less economic to fix up any design errors during plant operations.During our careers in mineral processing, nearly all of us will be involved in at least one plant design and I feel that it is as well if we understand some of these communication difficulties that can lead to a problem plant. There is little point in us being experts in mineral processing if the knowledge we have acquired doesn't somehow get incorporated into the plant.I would, therefore, like to present this short paper that mentions a few of the significant communication problems that can occur during the design of mining and mineral processing plants, together with some thoughts on answers to these problems."

Jan 1, 1973

By J. A. Bos, Z. Dai, P. Quinn, A. Lee

A flowsheet is being developed for processing Thompson ultramafic low-grade nickel ores. This type of ore is characterized by high content of serpentinized magnesium silicates which generate slimes during comminution. Flotation of this type of ore proves difficult due to problems associated with the slimes. The flowsheet, based on extensive laboratory and miniplant flotation tests, consists of two key components: desliming by hydrocyclones prior to flotation and using soda ash for pH control in flotation. Satisfactory metallurgical results have consistently been achieved in laboratory full circuit simulation and miniplant tests.

Jan 1, 2009

By Jose R. Hernandez-Aguilar

"Three models to predict the effect of bubble size (Db) on metallurgical response were tested in a pilot-scale flotation column at Teck Highland Valley Copper mine. The column was fed with slurry collected from the Cu/Mo separation circuit. The first model was the one developed by Gorain et al. (1997), which assumes that the collection zone rate constant (kc) is inversely proportional to Db. The second model was the one proposed by Hernandez-Aguilar et al. (2010), which considers kc as an inverse square function of Db. The third model was the one developed by Yoon and Luttrell (1989) which provides expressions to describe the efficiency of particle collection (E) based on first principles. The results showed a significant bias between experimental and predicted data using the model of Gorain et al. (1997), possibly reflecting the model’s inability to explain the impact of bubble size, bubble rise velocity and flow regime on E. The model of Hernandez-Aguilar et al. (2010) well described the experimental evidence. The model of Yoon and Luttrell gave accurate and unbiased predictions. However, Yoon and Luttrell’s approach calls for a criterion to determine whether the flow regime is potential or intermediate, a subject that requires more fundamental research.INTRODUCTIONParticle collection, i.e., bubble-particle collision followed by attachment, is the basis of flotation. In a quiescent environment (such as the one observed in a column, or away from the impeller in a mechanical cell), a collision event can take place as long as the “degree of turbulence” caused by the rising bubble does not prevent particle and bubble to flow in close proximity. Upon collision, the particle slides on the bubble surface for a period of time. If the particle is hydrophobic, attachment occurs when the “sliding time” is longer than the “induction time”, which is the time required to thin and rupture the intervening liquid (usually water) film forming a three-phase contact angle. While the induction time is largely influenced by the degree of hydrophobicity of the particle, the degree of turbulence is governed by the bubble size. Generally, direct control of bubble size is not exercised by most mineral processing practitioners, in spite of its obvious importance. Studies to model the effect of bubble size on particle collection using fundamental approaches have been conducted (e.g., Anfruns and Kitchener, 1977; Webber and Paddock, 1983; Yoon and Luttrell, 1989; Dai et al., 1999). However, these models have been validated under highly idealized laboratory conditions (micro-scale experiments using single minerals and uni-sized bubbles), far from resembling those existing in practical industrial applications. Fundamental studies to interpret the effect of bubble size on particle collection in industrial environments are largely absent in the literature. Partly because of this lack of practical knowledge, many mineral processing practitioners perceive laboratory “bubble size” studies to be valuable academic exercises, but not something that can be directly applied to daily production issues."

Jan 1, 2011

By W. A. Lang

Introduction Under our present civilization, industrial developments will be greatest in those areas in which energy .can be most economically produced and efficiently used, where labour is in adequate supply, and where markets for the products of industry are available. A knowledge of fuels- the present major sources of energy- and of their utilization is therefore of vital importance. With that in mind, the aim in this paper will be to outline the known reserves of fuels in Alberta, to give their characteristics, to indicate the markets served by each, and to offer some suggestions for the future development of the coal industry. The paper should be regarded as a compilation of published data rather than as an original treatise. Alberta is richly blessed by having large reserves of mineral fuels. The estimated reserves of coal are 46,562 million tons. Alberta is the oil and gas province of Canada. The world's largest deposit of bituminous sand occurs along the Athabaska river in Alberta. In addition, there are large areas of forested land in the northern and western sections of the Province, and the rivers serve for the development of hydro-power.

Jan 1, 1949

By W. P. Campbell

Foreword At the outset, it should be stated that this paper does not pretend to present a panacea for the ills that 'frozen' wells are heir to, but rather is an attempt to bring to the attention of those whose special concern it is, a little theory and some facts, which have been brought to light recently, in connection with the problem of 'freezing' as it applies to naphtha-producing wells in the Turner Valley field, and to draw some conclusions that follow from the facts discovered. It should also be stated that the investigation is not to be regarded as in any sense complete, but in progress. Doubtless new facts will be brought to light from time to time which may modify present ideas on the subject, but whether favourable or contrary, these will be welcomed, as the purpose of the Department is to secure as complete information as possible of the factors contributing to 'freezing', since this must be the first step to an intelligent attempt to remedy or prevent its occurrence, if such can be done. It is possible, too, that the cause or causes of freezing may not be the same in all cases, but whether this be so or not will have to be determined later as new information comes to hand. Introduction One of the worries which must constantly confront the operators of gas-naphtha producing wells in Turner Valley-although all, fortunately, have not met with it-is the possibility of the occurrence of what is commonly called 'freezing' (going off production).

Jan 1, 1930

By Carl Bertrand, Patrice Nadeau, Claude Bazin

"Rio Tinto Fer et Titane processes the ore extracted from the Lac Tio orebody to concentrate the hemo-ilmenite (FeO.TiO2-Fe2O3) mineral that is subsequently smelted to produce pig iron and titanium oxide slag. The ore is crushed, heat treated (roasted) and concentrated using dry magnetic separators. This paper describes a model to predict the magnetic susceptibility of the roasted ore and its behaviour in the magnetic separation plant. The model uses a classification of the ore as a function of the size and magnetic susceptibility of the particles. A subsequent division into mineral species allows the simulation of the magnetic separation process. The model is used to assess various operating options when process disturbances occur.INTRODUCTIONOre processing operations consist of ore size reduction followed by the recovery of valuable species in a concentrate that is subsequently sold for its minerals or metal content. The concentration processes are based on the physical and/or chemical properties of the minerals contained in the ore. Flotation is typically used to recover minerals of base metals such as copper, zinc, lead or nickel. Iron ore and other dense minerals are typically concentrated by gravity separation processes. Magnetic separation uses the magnetic properties of the minerals to concentrate magnetite and other minerals, to clean coal concentrate and to recycle ferrosilicon for dense separation processes (Brophy, 1985).Magnetic separators can be divided into low and high intensity separators and high gradient magnetic separators (Gillet, 2008). Most of the low gradient magnetic separators are built as rotary drums that are operated in wet or dry conditions. Dry magnetic drum separators are used by Rio Tinto Fer et Titane in Sorel-Tracy, Canada to concentrate hemo-ilmenite from the ore extracted at the Lac Tio Lake mine near Havre St-Pierre, Canada. The analysis of production data suggests that process improvement could be achieved by identifying key variables for the control of the magnetic separation circuit and/or by modification to the circuit flowsheet. The use of a process model was considered to be an effective approach to conduct a preliminary analysis of the circuit with a view toward process optimization. However, the literature contains few detailed studies dealing with the modelling of magnetic separation processes."

Jan 1, 2011