Search Documents

With the recent wider introduction of friction hoists of the Koepe type. for winding from depths of more than 3000 feet it has been found that failure by fatigue is the most common form of rope deterioration. Large numbers of wire breaks occur near the centre of the rope cross-section and it is difficult to detect these with certainty using the preferred d.c. magnetic test. For best results with conventional search coils their dimen- sions should be related to the typical wire break field pattern surrounding the longitudionally magnetised rope. The field of a broken wire was experimentally determined, using a Polish type MD6 Defectograph wire rope testing magnet and a short prepared length of rope with a movable simulated broken wire. The external field distortion perpendicular to the rope was measured by means of a gaussmeter and Hall probe. The advantages of this method are that terrestial magnetism and inherent rope "noise" have no effect on the results.

Jan 1, 1971

By Swift J. D

A key parameter affecting the performance of gravity thickeners in hydrometallurgical processing operations is the aggregation state of the feed after the addition of a flocculant. New procedures which measure the settling ratelsize relationship and the size distribution of aggregates in their process liquors have been used to quantify the aggregation state of the feedwell, overflow and underflow streams in a tailings thickener. The data obtained have been related to the thickener's operation and to a change in the flocculant dosage. A comparison is also made between the settling rate/size relationships determined with these new procedures and the mud-line settling rates from cylinder tests.

Jan 1, 1991

A novel solvent extraction process, called the SOHNEX process, has been developed at the University of Utah. In this process, the organic and the aqueous phases flow countercurrently in a horizontal vessel, and the emulsion between the two liquid phases is generated by high-velocity gas jets injected at the bottom. The gas jets are located at certain intervals along the bottom of the vessel with phase disengagement zones on either side of the plume zone created by the gas jet. The system is simple, having no mechanical moving parts or complex internal structures, and yet provides good contact between the phases with minimal backmixing. Tests have shown that emulsions with a wide range of specific interfacial area, including that typically encountered in mixer-settlers, can be generated in this process. It has significant built-in flexibility of operation including the control of the flowrate and hold-up of each liquid phase. The SOHNEX process overcomes the difficulties in the operation of conventional solvent extraction equipment such as mixer-settlers and column extractors. A major advantage of the SOHNEX process is that the energy of mixing can be closely controlled by adjusting the strength of the gas jet. This allows an optimal control of the drop-size distribution of the dispersed phase and thus the specific interfacial area. The process is continuous, and any number of extraction and separation stages may be built into a single vessel. The gas can be recirculated in a closed loop, thus eliminating solvent loss and mist problems, especially for high-temperature operations. The SOHNEX problem can handle solutions that contain suspended solids and that form third phases. The simplicity of the equipment and operation with low maintenance will mean much reduced capital and operating costs as well as low environmental risks and improved safety. The SOHNEX process has been tested for continuous copper extraction from a dilute solution. Calculations also showed that uranium and other radioactive elements can readily be extracted in a small unit of the SOHNEX extractor while satisfying the nuclear criticality condition.

Jan 1, 2000

Opencast blasting is notoriously subject to variable blasting conditions, some of which are related to changes in ground conditions and some to human and equipment factors. As drilling and blasting constitute a high proportion of working costs, control in this area is crucial for good management. During a recent exercise, wireline logging of blastholes was shown to have the potential to provide invaluable data for optimising blasting control and design. The paper reports on the exercise undertaken, showing that serious misconceptions as to the borehole diameters, explosive densities and posi- tions of decking were quickly corrected using the method. Potential use in blast design is discussed, as are the cost implications.

Jan 1, 1988

The Directional Drill Monitor (DDM) is an advanced instrument for real time in hole surveying. It was developed by Du Pont (Australia) to suit Australian gassy coal mining conditions. The instrument consists of three units: i. Down hole transmitter ii. Acoustic transducer iii. Data receiver processor unit (i.e. up hole unit). This paper describes the function of each unit in detail and highlights the importance of the DDM in long hole drilling efficiency. Surveying is carried out independent of hole depth. Each survey takes 2-3 minutes to complete, the frequency of surveying to control borehole trajectory is determined by the accuracy required for a particular hole.

Jan 1, 1992

By Conochie DS

SIROSMELT is a successful new pyrometallurgi- cal furnace system using a top-entry lance which can be submerged in both slag and matte. The lance is of simple construction, and is cooled by process air. Pilot plant work commenced in the CSIRO Division of Chemical Engineering in 1972 using a 50 kg batch reactor. This paper traces the development of the technology through various slag cleaning and smelting processes up to a scale of 5 tonnes per hour continuous feed. Strong co- operation between CSIRO and the Australian smelting industry has contributed greatly to the success of SIROSMELT.

Jan 1, 1984

By Zamel GI

The utilisation of fossil fuels, including coal (of which Australia is a large producer and exporter) is a significant contributor to the emission of greenhouse gases. Methane gas, formed during the coalification process, is present in coal seams to varying levels depending on the rank and depth of the deposit. This gas usually escapes to the atmosphere during mining operations without prior conversion to C02 or utilisation as fuel. The quantity of methane released can represent from less than one percent to more than five percent of the carbon content of the coal mined. Per unit of carbon, methane has a greenhouse impact many times that of C02. The emission of uncombusted methane to the atmosphere can therefore represent a greenhouse impact of similar porportions to that of the CO2 formed by combusting the mined coal. However, greenhouse emissions from coal can be minimised by collecting the coal seam methane and converting it to water vapour and the less damaging form, CO2. If such conversion is carried out while performing useful work, the methane can further reduce greenhouse emissions by displacing other fossil fuels. Technology has been developed to allow coal seam methane gas to be economically collected in a pure form, uncontaminated with air. This pure methane can be used to supplement natural gas supplies, to generate power or for the production of chemicals or substitute transport fuels. By collecting and utilising coal seam methane, the greenhouse impact from the mining and use of coal can be minimised, with significant reductions possible in the case of gassy deposits.

Jan 1, 1989

By Watsford RMS, Wickham P

In October 1980 the two existing flotation circuits were combined into a single new circuit. This circuit used modern 11.3 m3 flotation cells which replaced 1.4 m3 units. Sometime after this change, a significant deterioration in metallurgical performance occurred. This paper describes the work done to discover the causes of deterioration in performance and actions taken. The program implemented to prevent a future occurrence is also presented. The work included analysis of routine plant data, analysis of surveys to obtain element and mineral flows on both a sized and unsized basis, some quantitative mineralogy, and analysis of some external factors.

Jan 1, 1978

By Hedge AS

Mt Whaleback is one of the largest open-cut iron ore mines in the world. Haulage cost is the single largest component of operating costs at the mine. Past studies towards alternatives to truck haulage have recognised the potential viability of an in-pit crushing and conveying system, dependent on the proportion of uphill haulage. After seventeen years of mining Mt Whaleback still contains more than 1,000 million tonnes of ore, needing 1,800 million tonnes of waste removal to extract it. What was once a quarry has now turned into a large open pit. The increasing proportion of uphill haulage, the need to replace ageing 120 ton and 200 ton trucks and the necessity of achieving and maintaining a higher stripping ratio prompted, in 1984, the initiation of a new feasibility study into the viability of alternative material handling systems. A semi-mobile in-pit crushing and conveying system was found to be most suited to Mt Whaleback conditions. The East Pit was selected as the best location based on the analysis of haulage profiles measured on long term incremental mine plans. A capacity of 22 million tonnes per year was considered achievable by the proven technology currently available. A detailed estimation of capital and operating costs of two systems - one with trucks only and another with trucks, crusher and conveyor - for the removal of 22 million tonnes per year of waste rock, showed substantial cost savings achievable by the proposed system. An economic evaluation of the two systems established the advantages of constructing the in-pit crushing and conveying system. This is now under construction and will be commissioned in early 1987. Experience gained in constructing and operating this installation is expected to influence decisions on similar installations in future.

Jan 1, 1986

Of all of the processes in the mining cycle, blasting has the greatest impact on the efficiency of both mining itself and the initial stages of ore processing. The cost of blasting can be readily accounted for, but the true benefits of an effective blasting operation are seldom measured or reported. This means that blasting is seldom optimised in terms of its overall economic impact on an operation. Blasting operations have evolved according to the environment provided by mine management. Most operations seek to minimise the unit cost of each component process (overburden removal, blasting, excavation and transport, crushing or grinding) without recognising the impact that blasting performance has on subsequent activities. The creation of æcost centresÆ or æmanagement unitsÆ that isolate blasting from its downstream impacts reinforce this trend. Modern blasting technology is regarded as sophisticated by virtue of the mechanical design of the drills, the chemistry of the explosives and the flexibility and reliability of modern blast initiation systems. However, blast performance is controlled by the nature of the rock mass and there is generally an inadequate appreciation of how blast designs should be tailored to suit different rock mass conditions or to meet different blasting objectives. Most operations utilise a limited suite of standard designs without routinely tailoring designs to suit the actual conditions at hand or the objectives of each blast. Mining operations would benefit from tackling the following specific challenges:What is the appropriate target performance for blasting operations to generate the maximum economic benefit for the operation as a whole? How should designs be configured to suit the changing rock mass conditions and operating constraints? What compromise (if any) should be allowed from the ideal to assist conflicting scheduling or other operational requirements? How can blast performance be measured and reported to provide appropriate guidance to future operations? These challenges can be tackled through the process of æblast engineeringÆ. This paper discusses the potential impact of blasting performance on the economics of mining operations and the author argues that very considerable benefits over and above those currently being achieved could be realised by improving the routine engineering of mine blasts. The paper then explores how the industryÆs failure to recognise the economic importance of blasting has resulted in the engineering of blasting operations receiving less management and technical support than is appropriate. Finally, a simple approach to the engineering of routine blasting operations is described as an example of how these challenges can be tackled.

Jan 1, 1999

When the writer first saw the square-set timbering, he was at once impressed with the fact that the frames made by the sets, along the lode amI across it, were composed of panels with rectangular openings, and it was puzzling to understand howsuch a collapsible construction could resist pressure that came unevenly on it. Later he learnt that the sets did not satisfactorily resist such pressure, but mullock filling had, to a great extent, to undertake this duty for them. So it appeared that the setswere practically an expensive scaffolding, enabling the miners to work in the face and carry the stope forward, till the filling was put in behind them to take the pressure of the roof and sides of the excavation. Of course some of the pressure is takenby the sets, but this is because the set timbers prevent the filling being done perfectly; if it were practicable to remove the sets before filling, the filling by itself would more effectively support the back and wall, than do the combined sets andmullock. On the whole, therefore, the sets can hardly be said to be of much benefit where pressure has to be resisted. Despite this, the system has been of immense service in mining wide lodes, but for all that, it can only be pronounced a makeshift.This is no reflection on Deidesheimer, the famous originator of the square set, for, as will be shown later on, this way of...

Jan 1, 1911

By I J. Holland

Located in North West Queensland, XstrataÆs Mount Isa Copper Operations (MICO) is one of the largest underground mines in Australia with annual production exceeding six million tonnes of ore with average copper grades of three per cent. As at 30 June 2006, the Ore Reserve inventory totalled 87 Mt, with annual diamond drilling planned at >40 000 m in order to convert existing resources and test and define exploration targets. The role of the geology department within MICO is to collect, interpret and communicate relevant geological information to ensure the optimal extraction of ore. Routine underground inspections across multiple ore sources are undertaken and the information derived is then distributed to a range of professionals, operational personnel and management. The information is a æreal-timeÆ geological view for the stakeholders. Ongoing data collection and interpretation has developed a strong geological input to all mine planning processes within MICO. This has created strong synergies between mine planning professionals and a throughput benefit has been seen all the way to the concentrator. The MICO geological framework also provides avenues for a geological focus away from short-term production requirements, and as a result significant orebody scale observations and patterns have been realised that have led to an increase in the accuracy of geological and resource models. This has provided practical benefits for short-term scheduling and production, whilst enabling the realisation of long-term benefits that have a strong potential to increase the volume and value of the MICO resource. This paper will discuss the various mine geology contributions at MICO and illustrate some examples where mine geological input from graduate level has added significant value to the MICO business.

Jan 1, 2007

By Fredley D. C

Georgius Agricola wrote in De Re Metallica in 1556 that a prudent a miner should not work in a region ruled by a tyrant-a person inimical to mining. In 1926, Associate Chief Sherman of the United States Forest Service in a speech stated, "It is the policy of the Forest Service to encourage the development of the mineral resources within the boundaries of the National Forests ... a man who fails to cultivate a friendly, helpful, cooperative spirit in his relations with those who are endeavoring to develop the mineral wealth of our mountains has no place in the Forest Service." Both statements are as true today as they were in 1556 and 1926. The challenge to the Forest Service and the mineral industry today is to maintain that cooperation in a world that has changed significantly since Agricola and Sherman. The United States Forest Service manages 77,000,000 hectares of land-mostly in the Western United States-an area equal in size to New South Wales. The vast majority-75 million hectares are National Forests, and 1.6 million hectares are National Grasslands. National Wilderness Areas account for 13 million hectares or rough- ly 17 per cent of the National Forest System. National Forest System lands (NFS) are some of the most visible, scenic and controversial lands in the country. They are also some of the most valuable for their mineral potential and production. The value of mineral produced exceeds US$4 billion per year. There are over 1200 producing mines, 15,000 oil and gas leases, and some of the largest lead, copper, silver, gold, platinum, molyb- denum, and coal deposits in the hemisphere. Every year the Forest Service approves nearly 5,000 mineral operations on the NFS. Much of the NFS (75 per cent) is open to location of mining claims pursuant to the 1872 Mining Law. And an equal amount of land is legally available for oil and gas leasing.

Jan 1, 1991

By Greaves M. C, Amos M. D

A study was made of the instrumentation and technique of atomic absorption spectroscopy developed by Walsh of the Commonwealth Scientific and Industrial Research Organisation (CSIRO), Australia.The method was evaluated for the determination of silver in lead sulphide concentrate. The precision of the procedure developed is equal to that of the uncorrected fire assay method and the accuracy is greater.Brief mention is made of the use of this technique for the determination of silver and other elements in ores and concentrator products.

Jan 1, 1994

Two main aspects need to be considered when analysing a potential petroleum development project. Firstly, an estimate of the recoverable reserves must be made, and in many instances, these reserves must serve as collateral to finance development if outside capital is required. Secondly, the likely production profile and cash flow has to be established, and this cash flow then must meet debt service require- ments and in addition generate the required profits. In making these crucial deter- minations, the impact on the project of a wide variety of risks has to be analysed. A computer model, which represents the project in its entirety, is a great aid in determining project viability. Such a model requires imput from geologists, engineers and economists, and interpretation of the model must also be a joint effort. Communications, and inter react ion amongst individuals and disciplines is essential if the best answers are to be obtained

Jan 1, 1983

Proposals designed to use stockpiles and buffer stocks to achieve price stabilization and better resource use have a long history. They are super- ficially simple to understand. The benefits seem clear. And yet I am well aware that this is not a simple subject: the more one studies it, the more complex it becomes. Worldwide interest in re- source management, while receiving fresh impetus from the OPEC actions, also has a long and chequered history. Those venturing into such ter- ritories must be forewarned of the traps and pit- falls which abound. Interest in these schemes has waxed and waned over the years with the fluctuating fortunes of the producers or consumers. As I write this paper towards the end of 1977, I am acutely aware of the low ruling prices for zinc, copper, and nickel. These sacrifice prices remind me that it is difficult, for example, for a surveyor, to be calm and rational if he is up to his neck in a swamp full of crocodiles. He might be forgiven for forgetting that the aim was to drain the swamp! I am also aware that when swamps are drained, painful and dangerous stumps sometimes stick out. Hence, in looking at the subject of stockpiles and resource management we must not set our sights too high, perhaps not initially hope for perfec- tion, if we want to secure worthwhile changes. My approach is to acknowledge a bias for the market system. We have, however, had experience (remember the 1930s) of some weaknesses in the untrammelled operation of free markets. Thus our international economic relationships over the past 20 or 30 years have been based on a desire to retain as much as possible of a liberal world trading system backed by such organizations as the GATT, IMF, and the U.N. to ensure the necessary cooperation. Some nations have seen this system work only partially in their best in- terests. GATT, for example, has been reasonably effective in liberalizing trade in many manufac- tured goods but far less so in regard to agricultural or semi-processed goods.

Jan 1, 1978

By McKendry J. B

Gretley Colliery is situated at Wallsend, a suburb of Newcastle in New South Wales and is owned and operated by the Newcastle Wallsend Coal Ccnpany, a wholly owned subsidiary of Peko Wallsend Limited. The mine has been an efficient bord and pillar producer by industry standards. However, its continued economic viability was threatened because the bulk of remaining reserves lie in more difficult mining conditions and are of poorer quality. Alternatives were examined to improve productivity and allow Gretley to become more competitive in the current difficult market Environment.

Jan 1, 1988

By Valenta R. K

Copper-gold deposits associated with iron oxide rich rocks (ironstones) form a distinctive and significant ore association which occurs widely, but not exclusively, in the Proterozoic. The ironstone association is geochemically distinct from the BIF-hosted gold association (Phillips and Groves, 1983). Not only is the former association higher in its copper and commonly uranium, FEE, ¦bismuth, molybdenum contents, but also the ironstones in many cases do not originate as chemical sediments. Although both associations form in metamorphic environs, they reflect differing tectonostratigraphic settings and with consequent differences in ore-forming fluids and ore-forming mechanisms. This paper discusses the nature and origin of the ironstone-related copper-gold association, with particular reference to the Tennant Creek district in northern Australia, and emphasises the two stage origin of mineralisation. The genetic model developed has significant implications for other ore-bearing environments.

Jan 1, 1990

Preliminary petrographic investigations of eight Upper Permian coal seams of the Muja sub-basin, Collie Coalfield, reveal that the coal is high in inertinite and relatively low in vitrinite and exinite contents. The exinite content of Collie coal is relatively high when compared to other Australian coal of similar age. In addition the mineral matter content of the coal is very much lower than comparable Permian coal of Eastern Australia. The higher exinite content could be attributed to the type of Glossopteris flora, and the lower mineral matter content to the environment of deposition postulated for the Collie Coal Measures.

Jan 1, 1982

The provision of electrical power is an important consideration in project develop- ment. The first step to be taken in this area is to assess the power requirements of the project. The alternatives of taking a supply from a power authority or providing local generation can then be considered. This requires additional definition of the prob- able characteristics of the supply. The availability of authority power in Australia is limited by the extent of the state power grids. Recent developments now allow these grids to be extended and their load capacity increased to meet major load increases at less cost than was possible pre- viously. The options for local generation include diesel, gas turbine, steam, hydro, solar and wind, each having its particular performance characteristics and costs. The choice of fuel for diesel, gas turbine, and steam plant likewise involves consideration of a range of factors. The arrangements adopted for a number of development projects illustrate some of the aspects which influence the decisions on power supply.

Jan 1, 1986