Search Documents

By Boyd D. M

Minor magnetic anomalies which may be un represented on a magnetic contour map can be extracted from the original survey data and plotted by the described method to provide a rapid interpretation of the magnetic survey, provided that the data has been recorded digi- tally on magnetic tape. The example used comes from 40 kilometers south of Charters Towers, Queensland.

Jan 1, 1977

By Hagen G, Uhlig H

In the Federal Republic of Germany the thermal environment in underground coal mines has deteriorated progressively over the past years. The number and capacity of refrigeration plants have increased correspondingly. In recent years high capacity spray coolers have been used in addition to conventional cooling coils.

Jan 1, 1988

By Zhansen P

This paper describes the test re- sults which give a complete proccess of failure of concrete lining embedded in sand medium under load, including the order of appearance of crack along the lining up to failure. nor each crack appearance corresponding calculation being made to assess the redistribution of moment and thrust force in critical section including crown section, section making 45¦ with the vertical etc. De- flection at the above stated critical sections are also measured at each stage of loading. The pressure along the top hori- zontal surface of embedded lining and the vertical sides are measured by pres -sure gauges embedded in sand medium. fhe test results show a complete figure of rupture characteristics of concrete lining embedded in soft ground which approximates alluvial deposite often occur in metro construction at cities near the river side. These test results have been taken as a reference in assessing the action behavior of concrete lining in certain cities in China.

Jan 1, 1987

By D Maldonado

BlueScope Steel’s Port Kembla sinter machine underwent a major upgrade during mid-2009. The mixing and rolling drum (MRD) was thoroughly cleaned during the upgrade. Space factor measurements taken in October 2009 showed that the drum was operating in the cataract regime in the dry mixing section and the cascading regime in the rolling section, which is optimal for granulation. Sampling carried out during an entry into the MRD showed that both the Sauter mean diameter and the predicted bed voidage increase rapidly during wetting, and then decrease in the wet mixing section. In the rolling section, the granule properties remained constant untilthe drum discharge. Frozen particle analysis, using liquid nitrogen as the quenching agent, were carried out on material collected from the MRD discharge. The results, expressed as a Granulation Index, showed there had been a significant improvement in the granulating performance of the MRD following the upgrade. The plant studies were also complemented with laboratory scale experiments which aimed to optimise the granulation process. The effect of burnt lime on green feed permeability was quantifi ed using the laboratory scale drum at different moisture contents. A significant increase in permeability was apparent once the burnt lime dosing rates doubled from 1.1 - 2.2 per cent w/w (feed basis). The capacity of the burnt lime system at the sinter machine will be increased in order to benefi t from the expected higher permeability, permeability, which will enable the machine to sinter at deeper bed heights.

Jul 11, 2011

Black coals occur in most of the major sedimentary basins in Australia. In addition to the better known Permian coal occurrences of the Sydney, Bowen, Oaklands and Galilee Basins, coals of Permian age occur in the Arckaringa Basin in South Australia, the Bonaparte Basin in Northern Territory and the Collie, Perth and Canning Basins in Western Australia and the Tasmania Basin in Tasmania. Coals of Triassic age occur in the Ipswich Callide and Tarong Basins in Queensland, the Tasmania Basin in Tasmania and the Leigh Creek area in South Aus- tralia. Coal bearing rocks of Jurassic age occur in the Mulgildie Basin and Maryborough Basins in Queensland and in both the Queensland and New South Wales portions of the Clarence Moreton Basin and Surat Basins. They also occur in the Perth Basin in Western Australia. Rocks of Cretaceous age known to contain coal occur in the Styx, Maryborough and Laura Basins in Queensland, the Gippsland Basin in Victoria and both the Queensland and New South Wales portions of the Surat Basin. The coal measures have been deposited in a variety of sedimentary environments and the coals vary widely with regard to thickness, extent, banding characteristics, maceral and ash content. However, they are generally of low rank and most are suitable only for steaming.

Jan 1, 1975

By Flierman GA, Van Toor CH

Investigations were carried out of burden distribution using a full scale model of the furnace top. Various charging sequences were used and large differences were found between ore charged as sinter-pellets and as pellets-sinter. These were attributed to the differences in the angle of repose between the two materials. Permeability index was defined which was independent of the driving rate from which a furnace resistance index was obtained for use in weekly reports. Results are summarised as a single expression between blast rates and pressures and the values of Qbl and Qmax are continuously measured to aid the operators in controlling the wind rate in the safe AP region. Results also indicate a reserve in capacity of No. 7 BF.

Jan 1, 1975

By Carthew J

For more than 30 years shearer loaders have been the most important winning machines for,longwall mining. While the machines of the first generation had a driving power of only 100 or so kW, the present day shearer loaders may be powered by more than 1000 kW. Daily outputs of 24000 tonnes have now been reached, but this still does not set a limit. If the deposit conditions allow, further increases are possible. This requires the optimum coordination of all system components. For this paper the use of coal plows has been of little import as plows have found no favour, and nor are they likely to do so in today's economics in Australian coal mining.

Jan 1, 1988

The winning and upgrading of mineral raw materials necessarily includes size reduction, which serves the liberation and production of marketable products from highly valuable and bulk materials. For crushing, the following factors can be duly accounted for depending on material type and the selection of the suitable machine: ò producing a particular size distribution, ò producing a particular grain shape, ò selective comminution, ò gentle comminution, and ò producing a size range required by a specific process and/or for a specific product.

Jan 1, 1993

By Johnson N. W, Munro P. D, Pease J. D

The Lead/Zinc Concentrator of Mount Isa Mines Limited processes complex fine grained ore from the Isa and Hilton silver-lead-zinc orebodies, producing lead concentrate, zinc concentrate and (until 1996) a low-grade middlings (LGM or bulk) conc

Jan 1, 1997

By R Jacobs

"The Jaguar project is relatively unique in that it was evaluated, financed, built and operated to completion within the last ten years, providing the opportunity to holistically review and reconcile expectations against the actual outcomes. It is a case study that allows wider conclusions to be drawn with respect to the risks and opportunities involved with project evaluation and execution.Jaguar is located in the Leonora Mining District of Western Australia and was commissioned in mid-2007 as an underground accessed, single high-grade volcanic-hosted massive sulfide (VHMS) deposit with an on-site concentrator, producing copper and zinc concentrates exported via the Port of Geraldton to South-East Asian markets.The feasibility study (FS) had several iterations (JML, 2005a); the last dated July 2005 was specifically targeted to secure project funding, and summarised the reserves-only portion of the resource and its planned exploitation. The commissioning of the mine was the transition for the owner Jabiru Metals NL from junior explorer to producer and the project was the dominant asset of the company.Jaguar operated through several significant deviations from the linear project plan set out in the FS, including the Global Financial Crisis (GFC), a corporate takeover and disruption to the mine plan from the onset of material geotechnical issues. Whilst the GFC or mining disruption were not specifically predicted in the FS or peer reviews, the generic effects of the events were assessed in the project risk assessment and they influenced subsequent management decisions. In parallel to the internal project-specific risks, the short planned life of Jaguar was a risk to the continuation of the corporate entity which was being addressed by significant investment into brownfields exploration to extend or replicate the project, and ultimately added value such that attracted a corporate takeover.Holistically, the project delivered the returns predicted in the FS, but in a much different guise than was expected. This paper will describe the reality of operations compared with the study predictions and expectations through the perspective of the project and corporate risk assessment.CITATION:Jacobs, R, 2016. Jaguar base metals project case study – has reality reflected the study?, in Proceedings Project Evaluation 2016, pp 86–97 (The Australasian Institute of Mining and Metallurgy: Melbourne)."

Mar 8, 2016

By McNabb KE, Ward B, Dyer G

Roof conditions at Southern Colliery, the second longwall mine to be established at German Creek, were found to be much stronger and more massive than at the earlier longwall mine on the lease. Investigations were made to ascertain the level of face support required for longwall extraction under the changed geological conditions. Geotechnical information was provided from drillholes and highwall exposures. Downhole geophysical logs, notably the sonic velocity log, were used to obtain a distribution of the major lithological units over the mine area. A representative type section of the strata and geomechanical properties was compiled to form the basis for numerical modelling. Two-dimensional finite element methods were used to predict strata movements and chock loads under cantilevered roof conditions. The model incorporated a 6.3 in thick roof beam either bonded or detached, with either a 2 in or 5 in overhang. The solid rib, immediate roof, chock support and goaf were modelled as distinct parts, in addition a front abutment stress profile, derived from three-dimensional displacement-discontinuity analysis, was superimposed on the model.

Jan 1, 1992

By Nightingale R, Johnson B, Bensley C, Vince A, Keast-Jones R

In order to counter the massive increase in the level of near gravity material that would follow the reduction in dense-medium cyclone separation density at B.H.P. Slab and Plate Product Division's B and C coal preparation plants, "wing tank" systems to control medium density to within ¦0.005RD units have been installed. However, despite very precise density control, cyclone metallurgical performance has been less than satisfactory. The approaches taken to identify the causes of this poor performance and to justify alterations in operational and maintenance practices are presented.

Jan 1, 1987

The Ardlethan tin concentrator had dete riorated considerably in metallurgical per- formance, maintenance and plant availability. This problem was compounded by low tin prices and International Tin Council quotas. Mid- 1976 figures were: throughput - 1300 tonnes per day, availability 83% and metal recovery 537. Major problems existed throughout the circuit from crushing to tailings disposal and with morale, staffing, and housekeeping. With the lifting of the quotas in June 1976, management provided funds to implement a major rehabilitation programme and some fifteen major projects, at a cost of about $1.3 million have been completed to date. The change in performance has been dram- atic, and end of 1977 performance figures are: throughput - 1700 tonnes per day, availability 90% and metal recovery 65%.

Jan 1, 1978

By Zhen Y. Y, Cook A, Jell J. S, Fleming P. J G

Remapping of the Burdekin Basin has resulted in subdivision of the three interfingering basin-wide megafacies previously recognised in the Early to Middle Devonian Fanning River Group. Eleven carbonate and siliciclastic facies are now identified within the three megafacies, representing coastal plain, shoreline, nearshore, and shallow marine shelf depositional environments. The facies reflect two phases of a major transgression. An initial phase, in the Early Devonian, was confined to the far north of the basin, whereas a second, main phase, resulted in the encroachment of the sea from the east or southeast in the Middle Devonian.The proposed depositional model begins with the drowning of a coastal plain and the transgression of shoreline and nearshore facies between granitic and metamorphic headlands and/or islands. This was followed by the deposition of a patch reef and fringing reef complex including stromatoporoid and coral bioherms, biostromes, and oncolitic, crinoidal, and brachiopod-dominated banks/shoals, together with foreslopes and submarine channels, carbonate rubble deposits and terrigenous sediments. Sedimentation during the peak of the transgression was dominated by sheltered carbonate shelf facies, the maximum, flooding surface being recognisable across most of the Burdekin Basin. Progradation of muddy and sandy nearshore bay and shoreline facies soon followed, terminating carbonate deposition.

Jan 1, 1990

By Askew JE

The large, massive low grade gold orebody at Mount Charlotte has demanded an innovative approach to mining engineering. In the last five years several advances occurred in the areas of rock mechanics, mass blasting, blasthole drilling and truck haulage.Successive crown pillar failures throughout the life of the mine had resulted in a continuous geotechnical program, mostly utilisingconsultants. The culmination of this workwas the development of a successful crown pillar support system. Several stopes have incorporated the technique and the most notable success has been the relatively large F3 crown pillar.In hole hammer drilling was introduced to the mine in 1979, but little work had been done to develop a blasting system to suit the 165mm diameter holes. A non-electric sequential blasting system was adapted for use at themine and up to 600,000 tonnes have been fired successfully in an individual blast. Problems with ground vibration were addressed although this work remains incomplete.

Jan 1, 1984

By Moore A. J, Evans R

Blast vibration control and assessment techniques have been developed which supplement traditional charge mass scaling methods. The improved techniques, which can be used to predict air and ground vibration levels at the planning stage, and to assist in the control of blasting operations, have reduced the level of operating risk concerning blast vibration. In addition to such factors as charge mass, distance and blast vibration levels, these additional techniques take account of orientation of the blasting face, topographic shielding, wavefront reinforcement, and meteorological conditions. They have assisted in compliance with specified blast vibration levels for environmental licence and mining lease conditions, the reduction of blast vibration nuisance to residents in the area surrounding a mine, and control of building and rock structure response in adjacent areas on the mine lease area.

Jan 1, 1994

By Ward C. W

Conventional polygonal and block modelling techniques inadequately represent the grade-thickness distribution of some narrow shear and stratabound gold deposits. The polygonal influence of high-grade drill intercepts can result in overestimates of resource tonnages at high-grade cut-offs. Although block modelling methods provide grade smoothing and a better representation of structural continuity, the technique can lack precise definition of ore width. An alternative method known as Spatial Object Modelling (SOM) has been developed on MineMap software to overcome some of these modelling issues. This method does not rely on a uniform cell size and allows grade smoothing between resource intercepts in three-dimensional space. The SOM technique creates grade-thickness bars on regular, user-defined spacings which allow easy visual comparison of raw intercept data to the interpolated model. Model cell values are readily transformed into isopachs, isopleths and resource perimeters for reporting and mine planning purposes.

Jan 1, 1997

By Zeni J. T

Gold was mined from quartz bodies at Ballarat East from the 1850s until closure of the last mine in 1917. The average depth of mines was about 350 m.Ballarat Goldfields Limited (BGL) carried out diamond drilling from surface between 1985 and 1987 which proved the continuation of gold-quartz mineralisation beneath the old mines.During 1989 an underground development program was commenced to access the mineralisation for detailed exploration. The program included two simultaneous shaft developments. These were known as B2 shaft and Llanberris No.1 shaft.

Jan 1, 1992

By Loo C. E

Thirty two polyacrylamide flocculant samples were selected from the wide range offered to the Australian coal industry. An extensive test program was conducted to consider the properties of the flocculants, the substrates, the process conditions and the water chemistry encountered in coal preparation plants. The study indicated that flocculants with molecular weights of 12 to 14 million and degree of hydrolysis around 40% gave the best "average" performance over a wide range of process conditions. The pick-up and filtration of fine coal was demonstrated on a pilot scale to be a critical function of flocculant properties. This study also showed that the agitation intensity during flocculation was a critical parameter in determining the settling rate of the slurry and the clarity of the resulting supernatant. An electronic meter to measure agitation intensity was designed, constructed and tested to demonstrate how, for the first time, laboratory results can be implemented in operating plants.

Jan 1, 1989

By Edwards A. B

Re-opening of the old Proprietary mine has provided new exposures of the system of uralite dolerite dykes observed in 19110 by the Geological Sub-Committee of the Scientific Society of Broken Hill. The newly exposed dykes have been invaded and replaced by the massive ore, with development of manganese garnet and biotite adjacent to the sulphides. A similarly altered dyke in massive ore has been encountered in the North Broken Hill mine.The textures of the unaltered portions of these dykes indicate that they have not been affected by the intense regional metamorphism that has recrystallized the other rocks of the area. Moreover, in mineral composition and textures, in chemical composition, and in cross-cutting relations, they are so similar to the uralite dolerites of the district which post-date the folding and metamorphism of the Broken Hill area, that they must be regarded as typical members of this suite of post-metamorphic dykes.The invasion and replacement of the dykes by the massive sulphide ore, and their metasomatic alteration adjacent to the invading sulphides, establishes that the lode was formed after the dykes were intruded, so that the high temperature features of the ore cannot be attributed to metamorphism and recrystallization, but are primary features of high temperature hydrothermal deposition.INTRODUCTIONTwo cross dykes are recorded on the plan of the 300-ft. level of the Broken Hill lode accompanying the report on the geology of the Broken Hill lode published by the Geological Sub-Committee of the former Scientific Society of Broken Hill (1910). One dyke occurs in Block 12, and the other in Block 13, and both were stated to consist of a dark basic amphibole rock, called diorite for convenience. The more southerly dyke was traced from some distance out in the footwall, and even through the lode, by means of occasionalpatches of it still existing in the ore, in a direction...

Jan 1, 1956