Search Documents

By Iley J. D, Siviour N. g, Moffatt R. J

The process of desilverising by fractional crystallisation with reflux was investigated through laboratory batch tests and continuous laboratory bench scale tests at CSIRO Clayton, to a 300 kg/hr pilot plant at Port Pine. The pilot plant built at BHAS comprised a vertical cylindrical refining column with internal diameter 250 mm and height 3.2 m, attached at the top to an off-set cylindrical stirred crystalliser tank. Crystals were made in the crystalliser by intermittent immersion of steel cold fingers, which were water cooled between immersions. Gas heat was used for melting the crystals at the base of the column and for side compensation heating. A computerised in strumentation system was employed for data logging and for controlling some critical plant operations. A mechanical device was first employed to promote counter-current plug flow of crystals down the column against the rising stream of reflux liquid, but this was found to be unsatisfactory owing to excess noise, frequent mechanical failure, and excessive accumulation of dross. Plug flow was finally promoted by pulsing the column. Low silver levels, less than 1 gitonne, were achieved with both methods of crystal transport under total reflux conditions. The pulsed column gave results for silver and bismuth which agreed with the theoretical predictions of a computer model, but there was some selective drossing of antimony. In the mechanically agitated column, excessive drossing promoted selective removal of most of the antimony and some of the bismuth, and the results after extended operation were well removed from the theoretical predictions. Plant failures and operating problems prevented the achievement of satisfactory product quality with the necessary reliability under production conditions. Other priorities necessitated the termination of the project before the process could be optimised.

Jan 1, 1989

By R J. Butcher

Many deposits have been evaluated as potential block caves over the last 20 years due to the perceived benefit of low operating costs. However, block cave projects are typically capital intensive, with mass mining providing high throughput rates that required large investments in mining, processing and utilities infrastructure. While the key economic metrics in deciding to proceed with a caving project are typically net present value (NPV) or internal rate of return, these may not represent the best decision metrics for some companies. Where a caving project is competing for scarce capital amongst other projects in a company’s portfolio or where the caving project is the only project being evaluated by a company trying to raise capital, other metrics may be more appropriate. This paper explores the use of present value ratio and the minimising of maximum negative cash flow as suitable metrics in determining alternative strategies. Trade-offs between optimising for economic value and capital efficiency measures allow for decision-makers to evaluate potentially higher-risk, higher-capital and maximum NPV projects against lower-risk, lower-capital projects.CITATION:Stewart, C A and Butcher, R J, 2016. Block cave evaluation, in Proceedings Seventh International Conference and Exhibition on Mass Mining (MassMin 2016), pp 809–816 (The Australasian Institute of Mining and Metallurgy: Melbourne).

May 9, 2016

By Kuzmitch O, Morozov A

The main direction in the mechanisation in the mines of the Donbas and the USSR is long-face technology with complexes on the base of hydraulic supports. On the base of the 30 year old experience of exploitation of the coal clearing systems the serious data about the behaviour of the contained rock, display of underground pressure 'on longwalls and preparatory workings have been accumulated. Exploitation works in mines of the USSR are carried out at different depths: from 1000m to 1200m. There are 26 mines in Donbas, which exceed the depth of 1000m. It is the mines of Donbas, where is a rich experience of the exploitation of coal seams in various conditions. Besides, there are wide variations on the factors of the extraction thickness, depth of seam, angle of dip, occurrence of gas dynamics and others. In many scientific establishments, and in Donetsk Polytechnical Institute also, there are scientific research/results, which can be of interest for the coal mining countries.The volume of coal mining from longwall system-mechanised walls in Donbas became stable at the end of the 70s at level of 70 percent. All the efforts to increase this level have not given any notable results, not saying about the technical-economical data, which gradually deteriorate. It shows that positive progress in using the technology for the long walls is over and it is necessary to find new ways of mechanisation of coal winning.

Jan 1, 1991

By Z Li, Z Yan, T Htet, S Zhang

During the pyrometallurgical processes, a substantial quantity of high-temperature ironmaking and steelmaking slags, generated at temperatures ranging from 1400 to 1600°C, is wasted, as the heat contained in these slags is released into the environment during the tapping process without effective utilisation. On the other hand, a significant amount of energy is required to reheat the cold materials for the manufacturing of glass and mineral-wool, often necessitating the addition of high-silica materials to facilitate the production process. In this study, an innovative approach is presented to harness the heat present in molten metallurgical slags to directly produce new raw materials for glass and mineral-wool manufacturing while simultaneously reducing energy consumption and mitigating CO2 emissions. The theoretical amount of waste glass that can be effectively added in the process has been estimated via thermodynamic calculation. Experimental assessments were conducted to examine the impact of high-silica waste materials on the dissolution, melting and fluidity. Potential recipes for glass and mineral-wool manufacturing were suggested and an assessment of the energy savings, and reduction in CO2 emissions with manufacturing of glass and mineral-wool using this innovative approach were included. It was determined that the processes could lead to a reduction of over 26 kg of CO2 emissions per 100 kg of new material used, primarily due to the utilisation of heat from slag and the accelerated smelting process.

Aug 21, 2024

By C M. Zammit, N Cook, F Reith, C L. Ciobanu, J Brugger

The role of biological agents in the gold mining industry is currently limited to the use of microorganisms in bioleaching and bioremediation. However, there is a variety of possibilities in which biotechnology could aid the mining industry in the future. In this article we discuss the potential for the development of these novel biotechnologies and the role they can play in the exploration for new gold deposits, the processing of ores and the post-mining remediation of sites. The development of these biotechnologies has been enabled by rapid advances in our molecular-level understanding of the role microorganisms play in the solubilisation, dispersion and precipitation of gold. An understanding of the distribution of microbial species in soils overlying mineralisation can be utilised to develop bioindicator systems that assist with gold exploration. An in-depth knowledge of how microorganisms interact with gold complexes is being used to develop in-field biosensors, supporting exploration. Processing technologies may be improved based on advances in our understanding of the interactions between microorganisms, ore minerals, cyanide and gold. For instance, cyanide-producing microorganisms are being investigated for use in in situ leaching of gold. In turn, the use of cyanide-utilising microorganisms for the degradation of cyanide is being explored. Combined, the implementation of these biotechnologies in the gold mining sector may revolutionise the industry, leading to greener, more efficient exploration for and extraction of gold.CITATION:Zammit, C M, Cook, N, Ciobanu, C L, Brugger, J and Reith, F, 2013. Possible future applications of biotechnologies in the gold industry - a prospective approach, in Proceedings World Gold 2013 , pp 233-244 (The Australasian Institute of Mining and Metallurgy: Melbourne).

Sep 26, 2013

By N Haque, S Northey

Water in mining, mineral processing and metal production on a life cycle basis has been at the top of agendas for various industries, government agencies, research organisations, academic institutions and communities. As a result, a number of water footprint assessment methodologies have been developed. However, their practical applications in mining and mineral processing industries with specific case studies are still rare.A key objective of the Minerals Down Under Flagship is to contribute to the long-term sustainability of the Australian mining and mineral industries. Researchers in the Mineral Futures theme have developed robust assessment methods to evaluate the impact of mining and minerals technology development on the environment. The future of mining and the mineral industry is strongly linked with its sustainability - better water management strategies will need to be implemented.Life cycle assessment (LCA) has been a recognised method for measuring the environmental impacts of products, processes and services. It provides a scientifically sound method of comparing products and processes using a common basis and identifies so called æhot spotsÆ and opportunities for reducing environmental impacts. The water footprint of mining, mineral processing and metal production using an LCA basis is still scarce in the literature. Research methodology is now being applied in detail for copper, gold and nickel. A primary focus has been the relationship between ore grade and water use for which mathematical models are being developed. These types of models provide inputs for LCA of mining and mineral processing plants and can identify water saving opportunities through scenarios and process route analysis.CITATION:Northey, S and Haque, N, 2013. Life cycle based water footprints of selected mineral and metal processing routes, in Proceedings Water in Mining 2013 , pp 35-50 (The Australasian Institute of Mining and Metallurgy: Melbourne).

Nov 26, 2013

It is no longer adequate when starting a new mine to simply select the best equipment. Today's competitive international commodity markets demand superior efficiency which requires systematic involvement of people in continual improvement of production and commercial processes. True Total Quality of Management (True TQM) principles provide an operating philosophy for maximising productivity and minimising unit costs of output. The presentation will show the practical and successful use of these principles. This paper will introduce the case study and provide background material on True TQM.

Jan 1, 1995

It is no longer adequate when starting a new mine to simply select the best equipment. Today's competitive international commodity markets demand superior efficiency which requires systematic involvement of people in continual improvement of production and commercial processes. True Total Quality of Management (True TQM) principles provide an operating philosophy for maximising productivity and minimising unit costs of output. The presentation will show the practical and successful use of these principles. This paper will introduce the case study and provide background material on True TQM.

Jan 1, 1995

By C A. Foss, K Blay, K Leslie, D Hillan

Magnetic field studies provide remote sensing of magnetisation distributions and a means to investigate moderately- to strongly-magnetised ore deposits that may be partially or totally buried. However, above-surface magnetic field surveys have limited capability to resolve the detail of magnetisation distributions because of the large separation between the magnetisation and the magnetic sensor. While some of this detail is available from magnetic susceptibility logging within boreholes or from magnetisation studies on recovered core, these measurements are limited to the exact trace of the boreholes. The large disconnect between ground or aeromagnetic surveys and highly-localised borehole sampling can cause problems in developing robust source models from magnetic survey data. The measurement of magnetic field in boreholes has the capacity to at least partially bridge that gap by measuring the magnetic field due to magnetisations proximal to, but not intersected by, the boreholes.CSIRO has developed the world’s first downhole magnetic tensor gradiometer. This instrument measures magnetic field gradients in all directions within a borehole. A prototype instrument has been built and tested as part of phase 1 of the Deep Exploration Technologies Cooperative Research Centre (DET CRC). The prototype performed well with magnetic pyrrhotite at the DET CRC test site in the Adelaide Hills and at Carpentaria’s Hawsons magnetite deposit south of Broken Hill. Further work is required to reduce the diameter of the probe so that it can operate in NQ holes (it is currently limited to HQ or wider) and to transform it to a continuous logging tool. The borehole tensor gradiometer can be used to investigate the continuity of magnetisation over a distance of several metres to tens of metres away from a borehole intersection and the structural dip of the magnetic body. It can be used to either replace or augment downhole magnetic susceptibility logging. This instrument is one component of an integrated CSIRO suite of new magnetic field utilities and methodologies for iron ore exploration and development.CITATION:Leslie, K, Foss, C A, Hillan, D and Blay, K, 2015. A downhole magnetic tensor gradiometer for developing robust magnetisation models from magnetic anomalies, in Proceedings Iron Ore 2015, pp 299–304 (The Australasian Institute of Mining and Metallurgy: Melbourne).

Jul 13, 2015

By A Woodley, G Keir

The mining industry faces concurrent pressures of reducing water use, energy consumption and greenhouse gas (GHG) emissions in coming years. However, the interactions between water and energy use, as well as GHG emissions have largely been neglected in modelling studies to date. In addition, investigations tend to focus on the unit operation scale, with little consideration of whole-of-site or regional scale effects.This paper presents an application of a hierarchical systems model (HSM) developed to represent water, energy and GHG emissions fluxes at scales ranging from the unit operation, to the site level, to the regional level. The model allows for the linkages between water use, energy use and GHG emissions to be examined in a flexible and intuitive way, so that mine sites can predict energy and emissions impacts of water use reduction schemes and vice versa. This paper examines whether this approach can also be applied to the regional scale with multiple mine sites.The model is used to conduct a case study of several coal mines in the Bowen Basin, Australia, to compare the utility of centralised and decentralised mine water treatment schemes. The case study takes into account geographical factors (such as water pumping distances and elevations), economic factors (such as capital and operating cost curves for desalination treatment plants) and regional factors (such as regionally varying climates and associated variance in mine water volumes and quality).The case study results indicate that treatment of saline mine water incurs a trade-off between water and energy use in all cases. However, significant cost differences between centralised and decentralised schemes can be observed in a simple economic analysis. Further research will examine the possibility for deriving model up-scaling algorithms to reduce computational requirements.CITATION:Keir, G and Woodley, A, 2013. Regional trade-offs between mine water and energy use - a water treatment case study, in Proceedings Water in Mining 2013 , pp 21-28 (The Australasian Institute of Mining and Metallurgy: Melbourne).

Nov 26, 2013

By G Love, S Maher

In Victoria’s onshore Gippsland Basin, geology is driving brown coal developments, and geologists are key decision-makers. Prompted by volatile energy prices and the likelihood of a carbon constrained future, significant work has been carried out on the next generation of technologies to be applied to this giant resource. These include new-generation gasification technologies, coal conversion processes yielding products as diverse as diesel and fertiliser, drying technologies producing thermal and metallurgical coals and in situ conversion processes. However, coals aren’t coals, and brown coal available for new projects will have different quality parameters and mining economics from that currently mined.New projects are likely to be developed on coals with moisture contents averaging 60 per cent and corresponding low energy values. Whilst ash values will be low, averaging just 5 per cent (dry basis), this will at times approach 10 per cent, which is a level that would challenge the installed-generation technologies. Sulfur values will average 0.4 per cent (dry basis), but at times exceed 0.6 per cent, requiring technologies that address the potential for sulfur dioxide emissions. Whilst localised high levels of the fluxes iron (>1 per cent dry basis) and sodium (>0.3 per cent dry basis) would increase fouling of installed technologies, they may be suitable for selected next-generation technologies.Project viability for this next generation of technologies will be strongly influenced by mining cost, and geologists are playing a role in identifying higher-value coal. At its simplest, this is being achieved for open cut mines through regional, vertical strip ratio assessments, which are considered a first-order proxy for mining cost. Follow up assessments are incorporating mining and processing cost, coal quality penalties and product revenues. At a regional scale, it is informing the likely location and relative timing of future mine developments, as well as thinking around rehabilitation strategies, infrastructure and land-use planning.For deeper coal, factors like macro permeability, the ability to isolate seams from aquifers, groundwater chemistry, pressure temperature conditions, connection with groundwater recharge and in situ biota are being used as vectors to in situ coal conversion opportunities.Matching coal to the next generation of technologies has benefited from regional-scale geological studies of coal quality and mining economics, and has benefited from early engagement between geologists, technology developers and project proponents.CITATION:Maher, S and Love, G, 2014. Matching brown coal to the next generation of Latrobe Valley projects, in Proceedings Ninth International Mining Geology Conference 2014 , pp 77–84 (The Australasian Institute of Mining and Metallurgy: Melbourne).

Aug 18, 2014

By Jaczkowski B

The lower orebody (LOB) at Chingola Divi- sion of Nchanga Consolidated Copper Mines Limited (NCCM) accounts for approximately 30 per cent of the total copper production for the company. The uniformity of the geology of the orebody lends itself readily to a computer based ore reserve calculation and accounting system. The mining units are physically defined such that a hierarchical type of com- puter file organisation can reflect the existing physical interdependencies. In 1972, a project team consisting of one representative from each of the mine planning, operational research, and computer services departments was formed to investigate and to define the technical mining requirements of the dynamic ore reserve system (DORS). The system was finally implemented in 1975ò

Jan 1, 1977

By J Knecht, R Klymowsky, E Burchardt

The wide spread introduction of SAG mills into grinding circuits 20 years ago was the last development which had a major impact on the design and economics of comminution circuits. Single SAG mills were able to replace batteries of high maintenance and cost intensive crushers in order to achieve high throughput operations. Today, where the head grades of gold and copper ores are falling, there is again a strong need for a significant breakthrough to reduce investment and operating costs as well as improve metal recoveries. High-pressure grinding rolls is the new technology available to meet this challenge. HPGRÆs are state-of-the-art in several mining and minerals applications such as the grinding of iron ores and concentrates, and diamond bearing ores. Reasons for their success in these industries are overall cost reductions and improved product properties achieved by the application of high compressive forces. But these ores are relatively soft, with unconfined compressive strengths up to 150 Mpa.

Jan 1, 2000

By A von Johannides, G J. van Hout, L F

In the past various systems have been used to plan the extraction of ore from block cave operations. These systems have varied from rather sophisticated models with empirical ægravity flowÆ rules applied to the very rudimentary models where only the recorded mined tonnageÆs have been accounted for against the available resource. The normal requirement of these models has been to only plan the movement of ground through the drawpoints. Little cognisance has been taken of the other parameters that affect the total mining operations. The intended purpose of the linear program planning system is to not only include the management, resource availability and geotechnical constraints, but to also include the mining rules. The paper will discuss the various constraints that have been considered, and attempt to illustrate where the system better serves the production system than previous ones. A brief technical discussion on the linear programming system is included.

Jan 1, 2000

By E Mielczarski

Determination of the adsorbed layer composition and structure at molecular and atomic levels and understanding adsorption mechanisms and dynamics are vitally important for the preparation of surface layers with specific functions. Direct information, at a molecular level, about mineral surface composition, its structure and surface distribution is crucial to perform an efficient separation process for mineral beneficiation. This information is equally important for modifying surface properties of industrial minerals for specific applications such as: fillers, composites, weathering resistance, etc. An understanding of the mechanisms and kinetics of the interaction of first adsorbed organic molecules with mineral surfaces is a fundamental requirement for the prediction and control of the macroscopic surface properties governing the efficiency of separation technologies or new material formulations. The developed infrared external reflection technique has a unique ability to study interface phenomena, at a molecular level, on heterogeneous substrates. The variety, precision and reliability of information about the interface phenomena delivered by this technique is superior to any other single technique. The experiments are fast and non-destructive. High sensitivity (starting from 20 per cent of the monolayer) in situ collected information in a multiphase system, even in the region of strong absorption of the substrate, makes this technique a very valuable experimental tool. The complexity of the recorded reflection spectra, their sensitivity to variations of the optical properties of all bulk and surface components and their spatial distribution in the system under investigation, are in fact the major strengths of this technique. A few examples of the application of this multi-diagnostic technique, for monitoring surface modifications of semi-soluble minerals for selective flotation, will be discussed in detail in this paper.

Jan 1, 2005

By T O Aspinall

The Australian mineral industry involves a diverse range of expertise and skills. Within that, the mining industry, representing mine planning, mine management and equipment operation, has capital intensive, high productivity equipment and a small but skilled workforce. Continuing education for all personnel in the workforce after formal school courses will be an important contribution towards improving competitiveness. The non-tertiary sector represents a significant proportion of the workforce and requires as much attention as the tertiary educated group. Competency Based Training is now being developed for the mining industry in Australia under the National Training Board and the mining industry is well represented in establishing standards and curriculum. TAFE is a major source of accredited courses but some mining companies are also developing internal courses not necessarily for external accreditation. Articulation of such accredited courses to tertiary mining engineering courses has been considered. The education and training of equipment operators through continuing education requires attention to operating skills, an understanding of the productivity factors under the direct influence of the operator and providing product quality to the customer. The education and training of mining engineers has been widely covered and continuing close involvement of the mining industry is required to ensure well balanced courses in technical and interpersonal skills as well as motivation to continue learning for life. Postgraduate research is a part of continuing education but the mining industry has to continually address the adequate recognition of post-graduate qualifications for the increased technical or management expertise and the development of better analytical and problem solving skills which can be directed towards improving competitiveness. More attention has to be paid to providing adequate financial incentives to attract suitable students, particularly after attaining some experience, and to address their professional career path with a company so they are not significantly disadvantaged by undertaking post-graduate studies. The Chartered Professional Engineer status as provided by The Institution of Engineers, Australia to qualified candidates is being considered by The Australasian Institute of Mining and Metallurgy as a further recognition of a member's specific expertise and competence in mining and metallurgical engineering. Continuing education plays a major part in the maintenance of the expertise and competence required for a professional engineer to develop and also to retain chartered status. Continuing education will be a significant part of the education and training of all the mining workforce towards improving the competitiveness of the mining industry. The major challenges will be the motivation of all towards lifelong learning and the integration of the various programs towards providing the opportunity for a steady and satisfying career progression.

Jan 1, 1994

By P Scholtz

Sustainability is one of those fuzzy words like innovation: everybody has an idea what it means, but if one starts asking for concise definitions then it becomes clear that everybody puts their own nuance on the meaning of these words. It’s not because these are difficult words per se, but rather because our understanding of them is highly dependent on the environment we work, live and play in. To remove any ambiguity and aligned with the risks that are faced by the human population today, the definition for sustainability that will apply for this paper is: generating value in the short term without destroying value in the long term.CITATION:Scholtz, P, 2018. Sustainable post-closure development – is it achievable?, in Proceedings Life-of-Mine 2018, pp 58–59 (The Australasian Institute of Mining and Metallurgy: Melbourne).

Jul 25, 2018

By N Collins, A Woodley, A N. Danoucaras, C McCombe, N C. Kunz

Over the past decade, the mining industry has come to recognise the importance of water both to itself and to others. Water accounting is a formalisation of this importance that quantifies and communicates how water is used by individual sites and the industry as a whole. While there are a number of different accounting frameworks that could be used within the industry, the Minerals Council of AustraliaÆs (MCA) water accounting framework (WAF) is an industry-led approach that provides a consistent representation of mine site water interactions regardless of their operational, social or environmental context that allows for valid comparisons between sites and companies.The WAF contains definitions of off-site water sources and destinations and on-site water use, a methodology for applying the definitions, and a set of metrics to measure site performance. The WAF is comprised of two models: the input-output model, which represents the interactions between sites and their surrounding community, and the operational model, which represents on-site water interactions.Members of the MCA have recently adopted the WAFÆs input-output model to report on their external water interactions in their Australian operations, with some adopting it on a global basis. To support this adoption, there is a need for companies to better understand how to implement the WAF in their own operations. Developing a water account is non-trivial, particularly for sites unfamiliar with the WAF or for sites with the need to represent unusual features. This work describes how to build a water account for a given site using the input-output model, with an emphasis on how to represent challenging situations.CITATION:Woodley, A, Danoucaras, A N, McCombe, C, Kunz, N C and Collins, N, 2013. A robust methodological approach for mine site water accounting, in Proceedings Water in Mining 2013 , pp 335-342 (The Australasian Institute of Mining and Metallurgy: Melbourne).

Nov 26, 2013

By S Hancock, B H. Brady, H Muhlhaus

The aims of this paper are to present the governing science, verify the performance and demonstrate the potential engineering applications of a computational simulator for in situ leach mining of non-ferrous minerals. Assuming that the target mineral is deposited either uniformly within rock matrixes (matrix-hosted) or on fracture walls (fracture-hosted), in situ leaching can be treated as reactive flow and transport in geological media (porous media for matrix-hosted ore deposits and fractured media for fracture-hosted ore deposits). Under this treatment, the processes of in situ leach mining for non-ferrous minerals can be quantified through several sets of equations and these coupled equations have been numerically solved. The computational simulator has been applied to the simulations of one-, two-, and three-dimensional in situ leaching cases. The computational simulator, together with laboratory and in situ leaching tests, can be used to:optimise the leaching chemistry; optimise the in situ scale mining operations; scale up the in situ scale test operation to a full-scale mining operation; and evaluate the post-mining environmental restoration plan.

Jan 1, 2000

By K Faure

At Sams Creek a peralkaline granite porphyry dyke hosts gold-bearing sulfide-quartz-siderite veins. The granite dyke intrudes Ordovician-Silurian metapelite and quartzite, and has thin lamprophyre dykes along its contacts. The mineralised veins and the granite and lamprophyre dykes have been deformed during several phases of folding, the youngest of which is Early Cretaceous. The granite has been hydrothermally altered, with early magnetite-siderite¦biotite alteration overprinted by sulfide and quartz-siderite veins and quartz-perthite-albitesiderite-pyrite-rutile¦sericite alteration assemblages. The sulfide veins are composed of arsenopyrite + pyrite ¦ gold ¦ galena ¦ sphalerite ¦ chalcopyrite ¦ pyrrhotite ¦ graphite, with minor quartz and siderite. The gold contains significant silver (up to 30.8 wt per cent) and ranges in fineness from 692 to 844. Immiscible liquid-rich fluid inclusions, in quartz protected from recrystallisation by enclosing arsenopyrite, contain carbonic liquid that homogenised at temperatures of 320 - 355¦C. The Sams Creek gold deposit is distinguished from the orogenic gold deposit type by its stockwork veining, magnetite-siderite¦biotite alteration, high sulfide content, ore mineralogy and the absence of mineralisation in the metapelite country rocks. Features of the Sams Creek gold deposit do not fit neatly into existing classifications of granite-related gold-bearing deposits. The peralkaline composition of the Sams Creek granite and the absence of molybdenite and paucity of chalcopyrite, are major points of difference with gold-rich porphyry copper deposits. The presence of a lowsulf idation-state ore mineral assemblage, carbonate alteration and carbonic fluid inclusions at Sams Creek are typical of many of the reduced granitic intrusion-related type of gold deposit. However, notable differences are: the reduced type granites are metaluminous and calc-alkaline; and Sams Creek only has high As in contrast to elevated Bi, W, As, Mo, Te, and Sb in the reduced type. The Sams Creek deposit also shows affinities with gold deposits associated with alkaline magmatism, and it appears to be a new variant of this type as an As-Au deposit associated with a peralkaline granite and lamprophyre.

Jan 1, 2004