Search Documents

By Ursula E. Wolff

The precipitation of carbides from an alloy containing 33 pct Ni, 21 pct Cr, balance iron, was investigated electron microscopically by means of extraction replicas and thinned metal foils. Annealing temperatures ranged from 565°to 870°C and up to several thousand hours. M23C6 precipitated in pain boundaries, incoherent and coherent twin boundaries in that sequence. The orientation relationship between carbides and austenite matrix was determined and correlated with the morphology of the carbides and with the type of boundary in which precipitation occurred. In large-angle grain boundaries, as well as in coherent twin boundaries, the carbides had the same orientation as one of the adjacent pains. These carbides formed sheets of individual flakes with shapes related to the orientation of the boundary. In incoherent twin boundaries carbides precipitated in ribbons composed of pavallel rods. An unidentified subcarbide was found to precede precipitation of M23C6 in these boundaries. The M 23 C6 rods had a kind of fiber texture with (110) parallel to the long dimension of the rods and ribbon, and with orientations of both of the adjacent twin-related austenite crystals Predominant in the texture of the carbide. A hard sphere crystal model has been used to discuss orientation and morphology of the carbides in terms of free volume and vacancies available in the boundaries. A number of papers have dealt with the morphology of chromium carbide (M23 C6) precipitated in austenitic stainless steels.1"7 In all these investigations, the carbides were examined in the electron microscope by means of extraction replicas. With this technique, the carbides retain the spatial distribution they had in the bulk sample. However, since the matrix is dissolved in the process, the particles can turn in an unpredictable way; and the orientation relationship between matrix and carbides cannot be established. In this paper the results of studies on extraction replicas and on thinned metal foils are reported. These studies were undertaken to determine the matrix-to-car bide orientation relationship, and to correlate the orientation of the carbides with their morphology. PROCEDURE The material used was an austenitic alloy with 33 pct Ni, 21 pct Cr, balance iron, containing approximately 0.05 pct C. Coupons of 1.25-mm sheet were first solution-annealed at 1050°C for 15 min and air-cooled. Then, to precipitate the carbides, samples were isothermally annealed in the range from 565" to 870°C for times up to several thousand hours. All further specimen-preparation procedures were carried out after the final anneal. Carbon extraction replicas from polished and etched surfaces were made with 10 pct bromine in methyl alcohol.' Thin foils were prepared from punched-out 3-mm-diam disksg which fit into the electron-microscope holder. The disks were prethinned by grinding to approximately 0.5 mm thickness, and then electro-polished in a polytetrafluoroethylene holder1' with a solution containing 5 pct perchloric acid in acetic acid to which 10 g per 1 Cro3 and 5 g per 1 nickel chloride were added (etchant modified from that of Briers et al."). This solution dissolves neither the carbides nor the austenite around the carbides preferentially. By using extraction replicas, electron micrographs and selected-area electron-diffraction patterns were taken from the same carbide arrays. By using thin foils, electron micrographs were made from a grain boundary area containing carbides. Electron-diffraction patterns were then taken from the same area and from each of the adjacent grains separately. In this manner, the orientation of each grain could be determined without interference by the carbide pattern. A peculiarity of extraction replicas should be pointed out. After the matrix is etched away, the carbide arrays float freely in the etching and washing solutions, and are held in place only at the anchoring points in the carbon replica. When the replica is picked up with a screen the carbide arrays tend to flip to one side. Thus, while the surface features are preserved, the original arrangement of the carbides may severely and unpredictably be disturbed whenever the specimen contains large amounts of interconnected carbides. Nevertheless, it is possible to correlate the different morphologies of the carbides with the type of boundary in which they have precipitated. RESULTS 1) Extraction Replicas. Fig. 1 shows that the grain boundaries usually are curved, multicornered surfaces of random orientation. The coherent twin boundaries (which are (111) planes) cut a grain into parallel slices. Incoherent twin boundaries occur at the ends and on the steps of twins and are often narrow, parallel-sided strips which are much longer than they are wide. Different morphologies can clearly be distinguished for the M23Ce carbides precipitated in each of these types of boundaries, and agree well with those observed by kinzel.2 The kinetics of this precipitation has been investigated." The first carbides precipitate in junctions of three grain boundaries and fan out from there into the adjoining boundary surfaces, Fig. 2(a). These carbides are oriented randomly, Fig. 2(b), and become coarser and thicker as annealing time increases. The large-angle grain boundaries are next to fill

Jan 1, 1967

By Albert G. Zima

According to recently puhlished statistics, it is predicted that as much oil must be produced during the next 16 years as has been produced during the past 75, in order to satisfy the high rate of consumption of petroleum products. During 1934, over 17,000 oil wells were completed in the United States, and it is expected that over 20,000 additional wells will be drilled during the current year. Were it not for the remarkable progress made during recent years in the improvement of drilling technique and in the development of equipment used in the production phase of the oil industry, it is doubtful whether sufficient oil could be produced to meet present requirements. A few years ago, wells seldom were deeper than 3500 to 4000 ft., owing to the limitations of the drilling methods and equipment employed. Today, however, through the application of scientific drilling methods and the adaptation of modern equipment and improved materials, many wells range from 6000 to 8000 ft. in depth, and a few recent completions exceed 10,000 feet. Drill Tools Modern rotary drilling tools are the product of ingenious design and careful selection and adaptation of materials used in their construction. They must withstand terrific abrasion and, because of their compactness, must be designed to resist exceedingly high unit stresses. In bits, core drills and reamers, the bodies are made of either forged or cast alloy steels, heat-treated to develop a combination of high strength and toughness. To provide sufficient strength to the threaded portions and to protect the threads from distortion or damage, the box or pin sections of the tools are hardened to approximately 310 to 330 Brine11 hardness number. Drill and reamer cutters are generally of the movable type; i.e., serrated cones, cylinders or disks, which can readily be replaced when

Jan 1, 1935

By Albert G. Zima

According to recently puhlished statistics, it is predicted that as much oil must be produced during the next 16 years as has been produced during the past 75, in order to satisfy the high rate of consumption of petroleum products. During 1934, over 17,000 oil wells were completed in the United States, and it is expected that over 20,000 additional wells will be drilled during the current year. Were it not for the remarkable progress made during recent years in the improvement of drilling technique and in the development of equipment used in the production phase of the oil industry, it is doubtful whether sufficient oil could be produced to meet present requirements. A few years ago, wells seldom were deeper than 3500 to 4000 ft., owing to the limitations of the drilling methods and equipment employed. Today, however, through the application of scientific drilling methods and the adaptation of modern equipment and improved materials, many wells range from 6000 to 8000 ft. in depth, and a few recent completions exceed 10,000 feet. Drill Tools Modern rotary drilling tools are the product of ingenious design and careful selection and adaptation of materials used in their construction. They must withstand terrific abrasion and, because of their compactness, must be designed to resist exceedingly high unit stresses. In bits, core drills and reamers, the bodies are made of either forged or cast alloy steels, heat-treated to develop a combination of high strength and toughness. To provide sufficient strength to the threaded portions and to protect the threads from distortion or damage, the box or pin sections of the tools are hardened to approximately 310 to 330 Brine11 hardness number. Drill and reamer cutters are generally of the movable type; i.e., serrated cones, cylinders or disks, which can readily be replaced when

Jan 1, 1935

By K. K. Kershner, W. A. Calhoun, C. W. Funk

Future resources of aluminum may require the utilization of low grade ores to provide a more permanent protection for the nation. Aluminum minerals such as cloy, shale, and high iron laterites may become important sources. An evaluation of reserves is given. New laboratory results are reported on the Vereinigte desilication process. THIS report on future resources of aluminum metal emphasizes the necessity for investigating utilization of low grade potential ores to provide more permanent protection for the nation. Partial or complete interruption of the importation of high grade aluminum ores must be given consideration. Ultimately, aluminum minerals such as clay, shale, and high iron laterites may become the principal sources of aluminum. The development of extractive processes for treating these low grade materials is a step in long-range national preparedness that should receive more attention. In formulating such processes, the application of beneficiation methods for the purpose of classifying the several types of minerals before subjecting each type to the more expensive extractive procedures should be considered, and a careful survey of the basic factors of power sources, transportation facilities, and sources of raw material should be made. Domestic Bauxite Resources Of the domestic supply of current, treatable-grade bauxite, 95 pct comes from Arkansas. The present reserve of Arkansas bauxite suitable for metal production, including abrasive-grade, Bayer-grade, and modified Bayer-grade ores, is 34,000,000 tons. The total reserve of bauxite of all grades is approximately 75,000,000 tons. Reserves are estimated on a mined and dried basis. Data available to the Bureau of Mines in 1948 to 1949 were used in preparing Table I, which shows a breakdown by grades of bauxite for about a half of the reserves of the state. The modified Bayer ore, 10,555,500 long dry tons, is based on a cutoff of 8 to 15 pct silica. The sub- marginal 10,074,700 long dry tons is assumed to contain more than 40 pct gibbsite, more than 15 pct silica, and less than 32 pct available alumina. A considerable amount of this low grade material was consumed in 1949 and 1950. Additional tonnages of bauxitic and kaolinitic clays are indicated by the Bureau of Mines drilling project.' Applying a 50 pct factor to arrive at long tons mined and dried, the results of this project are approximately 31,500,000 tons kaolinitic clay at +35 pct Al²O3 and 11,800,000 tons kaolinitic clay at 20 to 35 pct A1,0,. Total reserves of kaolinitic clays are probably quite extensive—several times the reserves shown in the Bureau's work. Total reserves of bauxitic and high iron clays from the drilling program and previously established figures are 63,980,000 tons. The mineral dressing methods,' the lime-sinter process, he lime-sinter modification of the Pederson process," the lime-soda sinter process,"-' and the Alcoa combination processa. have been described in the literature and will not be elaborated upon here. The less familiar Vereinigte Aluminium-Werke process used by the Germans during World War 11 may require some amplification. It was used to bene-ficiate boehmite ores containing 12 to 18 pct silica for a feed to the European Bayer process. Ore was

Jan 1, 1952

By E. H. Dix

The success of the Charpy impact test in the steel industry has led those interested in aluminum alloys to investigate the possible application of this test to aluminum and its alloys. In this paper are set forth the results of a few preliminary tests made at the Lynite Laboratories of the Aluminum Manufactures, Inc. In order to study more thoroughly the significance of the Charpy test, slow-bending tests have been made duplicating the arrangement of the impact machine. Tests have been made on both notched and unnotched specimens of a series of copper-aluminum alloys. Apparatus The standard American-made Charpy impact machine delivering a blow of over 200 ft.-lb. was much too large to test aluminum-alloy specimens of the same type used for steel, so that it was necessary either to adopt a larger specimen or to have a special light-weight hammer made. Since there is no known relation between specimens of different sixes, even though geometrically similar, it was decided to adhere to the 10 by 10 mm. specimen. Accordingly, Sauveur and Boylston, the American makers of the machine, were asked to construct a special light-weight pendulum adapted to their standard machine, this pendulum to have one-tenth the capacity of the standard. The writer wishes here to acknowledge his indebtedness to Mr. H. M. Boylston for the personal interest and care exercised in constructing this pendulum. The machine with the light-weight hammer in place is shown in Fig. I. It is mounted on a concrete foundation with the concrete covering the flange on the base of the machine. Vibration is further prevented by four 5/8-in. (15.8 mm.) foundation bolts. The large standard hammer shown against the wall was also used for some of the unnotched bars that required more than 20 ft.-lb. to rupture. When the light-weight hammer was received, it was carefully cali-

Jan 1, 1921

By John Norton

IN recent years, the damping capacity of metals has come to be recognized as an important index of certain types of structural change. In a number of instances, this property has proved to be particularly sensitive, but insufficient work has been done to permit a general inter-pretation. There is considerable question at the present time as to just what factors are responsible for the internal dissipation of energy when a metal is carried through a cycle of stress, and these factors must be ascertained if the value of the damping method as a metallurgical tool is to be determined. Since internal stresses are among the chief causes of dissipation of internal energy, or damping capacity, it was thought that a study of the changes in damping during the recovery and recrystalliza-tion of a cold-worked metal might throw some light upon the subject, particularly if the damping changes were correlated with other properties that are better understood. Probably more work has been done on the recrystallization phenomena of alpha brass than on any other metal, so this was chosen as the material for the present investigation. Damping measurements on brass have been made by Förster and Köster.1 They showed that the annealing of a brass that had been cold-drawn to 50 per cent reduction produced a rapid fall in the damping, a flat minimum occurring at approximately the temperature of recrystal-lization. The damping remained at a low value until grain growth was well under way and then it increased rapidly with increasing grain size. Köster and Rosenthal2 continued the work in greater detail. They pointed out that the damping decrease does not correspond to the hard-ness drop but occurs at a lower temperature, suggesting that the relief or redistribution of internal stresses has a large effect while the actual recrystallization effect is small. They also show the increase in damping at the higher annealing temperatures. Their curves are reproduced in Fig. 1.

Jan 1, 1940

By Masatsugu Taniguchi

Onoda Cement Co., Tsukumi is one of the largest limestone producer in Japan. From mines called Suisho and Ganji, it supplies limestone for cement plant, lime manufacture, iron and steel industries and for many purposes. The Suisho mine is highly productive, though it's operations are governed by the utmost regard for its impact on the surrounding environment. However, it became difficult to meet additional expanding demand and to assure continuity of high rate production. Present production rate 1s 6 million tons per year. The Ganji mine, some 2 km south west of the Suisho mine, began first-stage development In mid- 1973 and in january I976 started production. The capacity of major facilities is 9 million tons per year. Full production is predicted in 1979. Mining and milling methods of these mines under strict environmental considerations are discussed.

Jan 1, 1976

By Elwood G. Haney, R. N. Parkins

Stress corrosion cracking of two heats of 18 pct Ni maraging steel in rod form immersed in an aqueous solution of 0.6N NaCl at pH 2.2 has been studied on un-notched specimens stressed in a hard tensilf machite. Austenitizing temperature in the range 1830 to 1400 F has been shown to have a marked influence on the propensity to crack, the loulest austenitizing- temperature producing the greatest resistance to failure. In the nzosl susceptible conditions, the cracks followed the original austenile grain boundaries; but when tlze steels zcere heal treated to inproze their resistance to stress corrosion, the cracks becatne appreciably less branched and slzouqed significant tendencies to become trans granular. Electron metallography of the steels indicated the presence of snzall particles, possibly of titanium carbide, along- the prior austenite grain boundaries and these particles u:ere more readily detectable in the structures that were most susceptible to cracking. Crack propagation rates, which appeared to be dependent upon applied stress and structure, were usually in tlze reg-ion of 0.5 mm per hr and may, therefore, be e.xplained on tlze basis of a purely electrochetnical ,nechanism. However, there is some ezliderzce from fractography that crack extension may be assisted by ttlechanical processes. Anodic stit)zulation reduced the tiwe to fracture, although cathodic currents of small magnitudes delayed cracking-; further increase in cathodic current resulted in a sharp drop i,n fracture litne, possibly due to the onset of hydrogen ewbrittlement. THE use of the high strength maraging steels, with their attractive fracture toughness characteristics, is restricted because of their susceptibility to stress corrosion cracking in chloride solutions. Although this limitation has resulted in investigations of the stress corrosion susceptibilities of these steels, there have been few systematic studies aimed at defining the various parameters that determine the level of susceptibility. It is the case that the usual tests have been performed with the object of defining some stress or time limit, on unnotched or precracked specimens, within which failure was not observed,' but while such results may be of some use in design considerations, they are necessarily concerned only with the steels as they currently exist and not with their improvement to render them more resistant to stress corrosion failure. This omission may be considered unfortunate because the indications are that stress corrosion in maraging steels shows dependence on structure in following an intergranular path, and since experience with other systems of intergranular stress corrosion crack- ing is that susceptibility may be varied by modifying heat treatments, a similar effect may be expected with maraging steels. It is sometimes from such observations that a fuller understanding of the mechanism of stress corrosion crack propagation begins to emerge, leading in time to the development of more resistant grades of material. The present work was undertaken to study only one aspect of the influence of heat treatment upon the cracking propensities of the 18 pct Ni maraging steel, namely the effect of austenitizing temperature, although certain ancillary measurements and experiments have been undertaken. EXPERIMENTAL TECHNIQUES Most of the measurements were made on a steel, A, having the analysis shown below, although a few results were obtained on a steel, B, having a slightly different composition. Both steels were supplied in the austenitized condition, A as 3/8-in-diam rod and B as 1/2-in.-diam rod. Cylindrical tensile test pieces were machined from the rods: the overal length was 2 1/2 in., the gage length 1 in. and the diameter 0.128 to 0.136 in. The stress corrosion tests were carried out with the specimens strained in tension in a hard beam testing machine, the necessary total strain being applied to the specimen over a period of about 30 sec, after which the moving crosshead was locked in position and the load allowed to relax as crack propagation proceeded; the load relaxation was recorded. The load was applied after the specimen had been brought into contact with the corrosive solution, the latter being contained in a polyethylene dish having a central hole through which the specimen passed, leakage being prevented by the application of a film of rubber cement. The specimen was in contact with the solution for over half of its gage length and the solution was exposed to the air during testing. The solution was prepared from distilled and deionized water to which NaCl was added, 0.6N, and the pH adjusted to 2.2 by HCl additions. The composition of the solution

Jan 1, 1969

By John D. Meahin

THE use of digital methods for generating crystallo-graphic data is well-established and many programs are now available. Transmission electron microscopy usually requires a knowledge of the electron diffraction pattern which is obtained by plotting a planar section through reciprocal space. With cubic symmetry these sections are very easily produced, but with hexagonal and lower symmetry systems considerably more labor is involved. Johari and Buchanan1 have written a Fortran program for generating standard projections and along similar lines we have produced a short but completely general program for generating any section through reciprocal space. The required inputs are the lattice parameters and angles for the real crystal. The Miller indices of the direction [U, V, W] parallel to the electron beam are then specified and the program will generate the Miller indices of the plane normals perpendicular to [U, V,, W] up to some specified integer. A subroutine can be inserted to test for forbidden reflections if desired. We have used such routines for fct and hcp crystals. As each permitted index is generated it is printed or punched out and no storage arrays are utilized in the computer. The normal diffraction pattern corresponds to the zero-order Laue zone, but with thin crystals or crystals of large lattice parameters the higher-order Laue zones may contribute to the diffraction pattern. Accordingly the program will generate successive Laue zones and project them onto the zero-order zone. The output of the program first lists the zone axis [C, V, W] and the Laue zone, and then gives a list of permitted reflections and the corresponding XP and YP coordinates of the reciprocal lattice point in angstroms-'. In addition, ZP, the perpendicular distance of the reciprocal lattice point from the (U, V, Ur) plane in reciprocal space is given, as is the reciprocal interplanar spacing. In the case of the zero-order Laue zone ZP is zero. A diffraction spot from the higher-order Laue zones will be very slightly displaced from the computed coordinates as its position in an actual pattern is given by projection along the diffracted beam2 and not along [u, V, w]. For any given electron wavelength this correction could be readily incorporated into the program, but as it only amounts to -1 pct it was decided to leave the program in its most general form, i.e ., a computation of points

Jan 1, 1970

By Linn Bradley, W. W. Strong, H. D. Egbert

A hot-dry method of cleaning the gas from blast furnaces has been shown1 to conserve the sensible heat energy of the gas, and in general it thus permits of a higher flame temperature. The electrical method of cleaning gases removes from 98 to 99 per cent. of the suspended matter in one operation when operating properly, thus making possible the use of a very clean gas for burning in the stoves. The use of such clean gas thus makes feasible a different type of hot-blast stove construction from that being used at present. It therefore seems advisable to construct the stoves from the viewpoint of getting the maximum amount of heat energy into the products of combustion. By preheating the air added to the top gas and obtaining a better mixture of the air and top gas, less excess air will be required and a higher flame temperature obtained from the combustion of the top gas. The interior of the stove should be provided with a kind of brick that will withstand a high flame temperature, will conduct the heat energy along certain directions, insulate the flow of heat along other directions and at the same time store heat energy so as to make the flow of such energy more uniform. It is quite likely that these results can be best obtained by using several kinds of bricks: one type which is a good insulator of heat energy to be used for lining the stove and for making partitions through the stove to restrain the flow of heat; another type of brick or material with high refractory qualities; and a third type which will be a good conductor of heat energy. The surface of the stove exposed to the atmosphere should be a minimum in comparison to the mass of checkerwork which it is possible to obtain, due regard being paid to other conditions. With clean and hot furnace top gas it will be advisable to consider a rearrangement of the checker work in the stoves. One season for the present size and shape of checker openings is to provide facility for

Jan 1, 1917

By W. Tovote

This paper is based upon 12 years' experience in the Southwest, including three years that were spent in constant traveling as examining engineer for the Phelps-Dodge Corporation. The material was gathered during rather extensive work in Bisbee, Clifton-Morenci, Globe, and Tombstone, and also on short and rapid trips into most of the mining camps and prospect fields of New Mexico, Arizona, the desert country of California, and as much of Sonora as was safe at the time. My methods of observation and my deductions are not put forward as new or scientific; they are simply rough field methods, based upon short notes, rough sketches, and largely upon memory, which I have found useful for coördinating geological data for the purpose of passing quick judgment on mining possibilities in certain districts exhibiting uniform characteristics. The opportunities for observation have been better these last few years than ever before, due to the unprecedented activity in mining, which has caused the reopening of hundreds of old mines and the starting of even more numerous prospects all over the mining states. Possible Systems of Classification By Geological Provinces There are a number of well defined geological provinces in the territory under discussion, and a study of their individual features is of interest. The following are a few of those that are most striking in their uniformity. 1. The "Desert province," extending roughly from Wickenburg, Ariz., to and beyond Barstow, Cal. In its north-south extent it reaches up to the Colorado River and down into Sonora, but overlaps other provinces. It is characterized by a worn-down basement of schistose and granitic rocks, on which rest remnants of Paleozoic and pre-Paleozoic sediments, including very old limestones. The sediments are disrupted and contorted. Alteration in the mineralized areas is very prominent, especially in the schists and limestones. Cenozoic volcanic rocks, principally of semi-basic composition, have been intruded into this complex and sometimes cover it as lava flows. 2. The "Yavapai schist" province, similar to the one first mentioned, consists of metamorphosed basic and semi-basic rocks. It lies in northern

Jan 1, 1920

By G. R. Speich

A cellular precipitation reaction in which cells consisting of an Ni3Ti (DO24) phase and austenite are formed has been studied in an austenitic Fe-30 Ni-6 Ti alloy. The variation of the growth rate and interlamellar spacing of the Ni3Ti cells with temperature has been determined m the range 400" to 975°C; the interlamellar spacing is proportional to the degree of undercooling; the growth rate can be expressed by an equation of the form G = K?T)2 exp(-Q/RT). The habit of the Ni3Ti lamellae is (001)Ni3Ti (111)y;[010]Ni3T2 [010]y. An almost perfectly coherent interface is formed between Ni3Ti lamellae with this orientation rela -tionship and the intervening austenite. This first Ni3Ti cellular product is subsequently consumed by a second cellular reaction of much coarser spacing. CELLULAR precipitation reactions have been studied in copper-base,1,2 Au-Ni,3 pb-sn,4 and iron-base ferritic5,6 solid solutions, and this mode of precipitation has been treated theoretically by smith," Turnbull,8,9 cahn,10 and more recently by bohm.11 In the case of substitutional austenitic iron-base alloys little or no data are available, Cellular precipitation reactions are well known in austenitic nickel-base alloys12,13 but usually these reactions do not proceed to completion because of general precipitation occurring in the matrix, and they have not been studied in detail. Precipitation from an austenitic Fe-30 Ni-6 Ti alloy was studied as part of a larger investigation of the mechanisms of precipitation from substitutional iron-base alloys. This alloy, austenitic at high temperatures, decomposes at lower temperatures by a double cellular precipitation reaction. The first decomposition product consists of alternate lamellae of an Ni3Ti(DO24) phase and austenite. The reaction proceeds to completion, consuming all of the original austenite. This first cellular product is subsequently consumed by a second cellular reaction of much coarser spacing. The first cellular reaction was studied in detail by light and electron microscopy, hardness measurements, and by X-ray and electron diffraction. Interlamellar spacings and growth rates were measured during isothermal aging in the range 400" to 975°C. The orientation relationship between the Ni3Ti and austenite lamellae was determined and indicates that an almost perfectly coherent interface exists between the two phases. This first Ni3Ti cellular reaction is of particular interest because it occurs over such a wide temperature interval. This allows cellular growth rates and interlamellar spacing data to be obtained for much larger degrees of undercooling than reported hitherto. MATERIALS AND EXPERIMENTAL PROCEDURE The Fe-30 Ni-6 Ti alloy was prepared from electrolytic iron, Mond nickel shot, and sponge-purity titanium* by vacuum melting in a zirconia crucible

Jan 1, 1963

By Carl D. Broadbent

In 1956, Kennecott Copper Corp. instituted a slope mechanics program. Its objective was to obtain effi-ient and safe pit slopes. Since then, Kennecott has onducted a great deal of research into the area, most otably at the Kimbley Pit. This paper, which describes the transitional work at this period and draws from the pertinent experimental work done by others, paves the way for the next step of the program: refining the design process and applying it for profit. The goal of slope mechanics is to achieve efficient and safe pit slopes. In the case of ultimate mine slopes, the objective is to minimize the stripping ratio by steepening the slopes to their maximum stable limit. On the other hand, the inclination of working slopes is normally established by operating space requirements and the function of slope mechanics should be the continuous surveillance of slope conditions to assure long-term stability and provide timely warning of impending slides so that corrective measures may be incorporated in production planning. In 1956, Kennecott instituted a program to provide

Jan 1, 1970

By T. E. Leontis

Data are presented in this paper to show that addition of zirconium to sand-cast Mg-Th alloys effects a marked decrease in the grain size of these alloys which is accompanied by a significant increase in the mechanical properties over the entire range of thorium content investigated. The beneficial effect of zirconium on the strength properties is maintained at elevated temperatures up to 700°F. In addition the alloys exhibit exceptionally high creep resistance at temperatures up to 600°F. Zirconium does not greatly improve the strength or creep characteristics of extruded Mg-'Th alloys. Cerium is not a desirable addition to Mg-Th-Zr alloys. IN a previous paper,' it was shown that addition of thorium to magnesium imparts exceptionally high resistance to creep at elevated temperatures both in the sand-cast and in the extruded states. The large grain size of the sand-cast alloys, however, renders them of questionable value as engineering materials. Sauerwald² showed that the grain size can be reduced effectively by the addition of zirconium. Results of a detailed study of the properties of Mg-Th-Zr alloys over a wide range of thorium content are presented in this paper. In accordance with the preliminary findings of Sauerwald,² it is shown here that Mg-Th-Zr alloys possess the unusual combination of fine grain size and a high level of strength and creep resistance at elevated temperatures. Some information on the effect of cerium on the properties of Mg-Th-Zr alloys is presented also. Effect of Th on Solubility of Zr in Molten Mg Sand-cast test bars and 3 in. diam extrusion billets of Mg-Th-Zr and Mg-Th-Ce-Zr alloys* were pre- pared according to the procedures described in the previous paper.' The zirconium was added in the form of sponge metal as supplied by the Bureau of Mines.' The maximum amount of zirconium that usually can be introduced into magnesium at the customary alloying temperature of 1350° F is about 0.7 pct. The analyses in Table I clearly show that thorium in- creases the solubility of zirconium in liquid magnesium. The tabulated zirconium contents are designated as "acid soluble;" this serves to distinguish these values from the small amount of zirconium that is not dissolved when the alloy is subjected to the action of a dilute acid solution. The "acid-insoluble" zirconium is believed to be ineffective as an alloying ingredient. The acid-insoluble zirconium contents ranged between 0.03 and 0.16 pct in the present alloys, the tendency was toward higher values in alloys with higher thorium content. In contrast to the effect of thorium, cerium decreases the solubility of zirconium in magnesium. This is shown by the three Mg-Th-Ce-Zr alloyst in- cluded in Table I and stands in agreement with the observations of Nelson and Stricter".' on Mg-misch-metal-Zr alloys. Effect of Zr on Grain Size of Mg-Th Alloys The potent effect of zirconium as a grain refiner has been demonstrated for many types of magnesium alloys.3-8 Of greatest importance to date are Mg-Zn-Zr alloys5,6,8 and Mg-mischmetal-Zr alloys.3,4,7 Zirconium has also been found to exert a marked grain-refining action on Mg-Th alloys. All the Mg-Th-Zr alloys cast in the form of ½ in. diam test bars have an exceedingly fine grain size (Table I). Reference to the previous paper' will show that binary Mg-Th alloys containing up to 6 pct Th are almost completely columnar even in the M in. diam reduced section of a test bar, and that 10 to 50 pct Th alloys have an equiaxed grain structure of 0.03 to 0.08 in. The data in Table I also show that addition of cerium to Mg-Th-Zr alloys has no effect on the grain size. In addition to increasing the strength properties, the fine grain size of Mg-Th-Zr alloys

Jan 1, 1953

By James Aston

A proper consideration of this subject is not confined to the technical channels of production and metallurgy. It concerns an industry, and should cover economic aspects which are of material importance in any program of development. The discussion may logically be treated under three subdivisions, as follows: (1) manufacture, (2) characteristics related to quality of material; (3) adaptability and exploitation of product. Manufacture of Wrought Iron The manufacture of wrought iron is the most ancient art of the ferrous metal industry. The eighty years or less of existence of processes identified with our modern "Age of Steel" is a relatively brief interval compared with the several thousand years associated with the production of wrought iron by man. From the primitive early methods of production, manufacture for many centuries followed the line of direct reduction. There were developments as experience was gained through the years; but man's needs for a strong, ductile, forgeable product were met by reducing the ore to metallic iron in a single-stage operation. Following the development several centuries ago of what has become our modern blast-furnace operation, manufacture of wrought iron was gradually transformed into a two-stage method of first producing cast iron and then refining this to the desired degree of forgeability; the forerunner in principle of today's scheme of manufacture of steel. The product retained the essential characteristics of highly refined base metal with iron-silicate slag incorporation, which were associated with the material resulting from direct reduction methods. Cort's invention of the puddling process in 1784 is a landmark in wrought-iron manufacture. It consisted essentially in adapting a coal-fired reverberatory furnace to the refining operation; thus lifting the industry out of the slough of

Jan 1, 1935

By Carle R. Hayward

SulphuR has long been one of the banes of the steel manufacturer and often no effort and expense have been spared in order to reduce it to a small per cent. in the finished product. This condition is due to a general conviction that in many cases where steels have failed in service, sulphur has been the cause. But there has been a growing feeling in recent years that the verdict against sulphur has been unnecessarily severe. In cases of segregation it was present in. augmented amounts along with other impurities, but it had not caused the segregation. High sulphur in pig iron is caused by poor furnace conditions and the sulphur is merely one indication of an iron that has not been properly reduced. No amount of subsequent treatment under oxidizing conditions in the open-hearth furnace can remedy the defects, although the per cent. of sulphur may be considerably reduced. In other words, the causes of bad steel can frequently be traced back to bad pig iron, and sulphur is merely one indication that the pig iron is bad. The writer recently visited a steel plant where a mass of evidence had been accumulated which substantiated this fact, and the superintendent was emphatic in stating that high sulphur was not harmful provided the steel was not otherwise poor due to insufficient reduction in the blast furnace. The presence of a moderate amount of sulphur is desirable from the standpoint of the man who machines the steel. The low-sulphur material drags and the production of a smooth surface is very difficult. A slight increase in sulphur enables the machinist to produce a smooth surface without difficulty. Since, therefore, such large quantities of steel are subjected to machining, it becomes highly important that the sulphur controversy should be settled, and if its presence is proved to be harmless the ban on it should be lifted. Among the recent papers on the effect of sulphur on steel is one by Dr. J. S. Unger, Manager of the Central Research Bureau, Carnegie Steel

Jan 1, 1917

By Arthur B. Cummins

POWDERED nonmetallic minerals and rocks of many different types are used extensively in industry for incorporation in compositions and manufactured products The term "mineral filler" is commonly employed to designate a material that is used for a specific purpose but not as an essential or reactive component Such a definition is not without objections, and it is indeed difficult to define fillers in any fully satisfactory manner, since the term has come to have so many different meanings and to cover such a wide range of uses. A filler is defined, for the purposes of this chapter, as a substantially inert material not specifically employed as a reactive or essential component, the primary function of which is to modify the properties or processing of a composition of matter or fabricated article Emery1 has emphasized that fillers change the properties of the product but are themselves unchanged in compounding or use The term "filler" appears to be rather general when referring to usages m bituminous compositions, rubber, composition floorings, fertilizers, plastics, textile finishes, and some others. In paper manufacture, in the paint industry and with insecticides, other terms are frequently employed, as is indicated, herinafter By placing emphasis on the function of the material used in modifying the properties of the composition or article, it is believed that a more useful classification of filler products and their applications may be derived. FUNCTIONS OF MINERAL FILLERS All of the manifold functions of mineral fillers cannot be listed in a summary review. A survey of the uses for these materials, however, shows that in nearly all cases the powders are employed to modify the properties of a composition of matter or those of a fabricated article, or to perform some useful function In the manufacture of either. A generalized list of these useful functions may be given is follows 1 To Modify Optical Properties Color Surface texture Opacity Brightness and gloss (as in paper and plastics) Flatness (as in lacquers and paints)

Jan 1, 1949

By F. W. Newhall, L. N. Plein

During the latter part of the year 1931, the Republic mine of the Republic Steel Corporation, at Republic, about 4 miles south of Brownsville, Pa., was mining coal along four rib or fracture lines. One of these lines, the west butt rib line, was retreating towards a concrete-lined air shaft, 320 ft. deep, which had been sunk in 1911 for ventilation purposes. With the normal rate of mining at that time, it was expected that this rib line would pass the shaft in three or four months and the shaft would then be abandoned and allowed to cave. Realizing the opportunity presented for the study of an unusual case of ground movement, the question of conducting the study was presented by the junior author to thechairman of the Institute's committee on Ground Movement and Subsidence, Mr. George S. Rice, who presented the matter to Mr. G. H. Morse, General Manager of the Northern Mines, Republic Steel Corporation, and he agreed to cooperate with the Bureau of Mines in making the study, the results of which arc presented in this paper. Acknowledgments are due to Mr. Morse for his full cooperation in this work and to Mr. G. S. Rice and Mr. J. W. Paul, both of the U. S. Bureau of Mines, for their advice and guidance during the course of the work. The authors are indebted to Mr. B. F. Herbert, mining engineer, Northern Coal Mines, Republic Steel Corporation, who assisted in all the surveys, and Mr. W. H. Smith, draftsman, U. S. Bureau of Mines, who prepared all illustrations for publication. Geologic Conditions The shaft is at Merrittstown, which is about one mile northwest of Republic. The topography in the immediate vicinity of Merrittstown consists of rolling country dissected by the meanders of Dunlap Creek and its tributaries. The surface slopes of the hills are gentle and their average gradient is less than 6º. The area at the point where the study was made lies on a hillside sloping towards the southwest, the gradient, varying from 1º to 14º. Fig. 1 shows contour lines at 5-ft. intervals on

Jan 1, 1936

By L. N. Plein, F. W. Newhall

During the latter part of the year 1931, the Republic mine of the Republic Steel Corporation, at Republic, about 4 miles south of Brownsville, Pa., was mining coal along four rib or fracture lines. One of these lines, the west butt rib line, was retreating towards a concrete-lined air shaft, 320 ft. deep, which had been sunk in 1911 for ventilation purposes. With the normal rate of mining at that time, it was expected that this rib line would pass the shaft in three or four months and the shaft would then be abandoned and allowed to cave. Realizing the opportunity presented for the study of an unusual case of ground movement, the question of conducting the study was presented by the junior author to thechairman of the Institute's committee on Ground Movement and Subsidence, Mr. George S. Rice, who presented the matter to Mr. G. H. Morse, General Manager of the Northern Mines, Republic Steel Corporation, and he agreed to cooperate with the Bureau of Mines in making the study, the results of which arc presented in this paper. Acknowledgments are due to Mr. Morse for his full cooperation in this work and to Mr. G. S. Rice and Mr. J. W. Paul, both of the U. S. Bureau of Mines, for their advice and guidance during the course of the work. The authors are indebted to Mr. B. F. Herbert, mining engineer, Northern Coal Mines, Republic Steel Corporation, who assisted in all the surveys, and Mr. W. H. Smith, draftsman, U. S. Bureau of Mines, who prepared all illustrations for publication. Geologic Conditions The shaft is at Merrittstown, which is about one mile northwest of Republic. The topography in the immediate vicinity of Merrittstown consists of rolling country dissected by the meanders of Dunlap Creek and its tributaries. The surface slopes of the hills are gentle and their average gradient is less than 6º. The area at the point where the study was made lies on a hillside sloping towards the southwest, the gradient, varying from 1º to 14º. Fig. 1 shows contour lines at 5-ft. intervals on

Jan 1, 1936

By Herbert Dlaska

The BBU - rotary hearth treats lead concentrates and battery scrap by the roast-reaction process. It corresponds in principle to the long-known Newnam hearth, however its hearth-basin is not straight but curved to a closed ring. In operation this annular hearth is filled with liquid lead and rotates around a central blast-box. The charge, heated to a glowing-red, floats on top of the lead bath, into which air is blown from the blast-box through a horizontal slot-type tuyere. Ore pellets and brown coal are continuously charged onto the reacting mass from two storage bins. Lead is set free by the roasting reactions and trickles through the charge into the lead bath from where it is tapped from time to time. The reacting mass is continuously stirred by a mechanical agitator and backed, by a mechanical shovel, against the water-jacketed wall of the blast-box. The gangue of the charge forms lumps of scorified character, the so-called hearth slag or grey slag, which are discharged from the hearth. The waste gases are collected in a hood and conducted to a baghouse from where the fumes and dust are automatically transported to the pelletizing installation and are recycled with new material. The daily output of lead bullion depends mainly on the lead content of the charge. With lead concentrates containing 74% lead, about 24 tons of lead bullion per day are produced on the hearth at a direct lead recovery of about 89 per cent. Approximately 10 per cent of the lead content of the new material passes into the hearth slag from where it can be recovered in a blast furnace or in a rotary furnace. For small lead smelters the BBU-process represents the most economical way of melting high-grade lead concentrates. The process requires a relatively small capital investment, consumes little fuel, utilizes cheap fuel and is very flexible. Further, of great importance, is the fact that battery scrap can be treated by the BBU-process with very good results.

Jan 1, 1970