Papers - Orientation and Morphology of M23C6 Precipitated in High-Nickel Austenite

The precipitation of carbides from an alloy containing 33 pct Ni, 21 pct Cr, balance iron, was investigated electron microscopically by means of extraction replicas and thinned metal foils. Annealing temperatures ranged from 565°to 870°C and up to several thousand hours. M23C6 precipitated in pain boundaries, incoherent and coherent twin boundaries in that sequence. The orientation relationship between carbides and austenite matrix was determined and correlated with the morphology of the carbides and with the type of boundary in which precipitation occurred. In large-angle grain boundaries, as well as in coherent twin boundaries, the carbides had the same orientation as one of the adjacent pains. These carbides formed sheets of individual flakes with shapes related to the orientation of the boundary. In incoherent twin boundaries carbides precipitated in ribbons composed of pavallel rods. An unidentified subcarbide was found to precede precipitation of M23C6 in these boundaries. The M 23 C6 rods had a kind of fiber texture with (110) parallel to the long dimension of the rods and ribbon, and with orientations of both of the adjacent twin-related austenite crystals Predominant in the texture of the carbide. A hard sphere crystal model has been used to discuss orientation and morphology of the carbides in terms of free volume and vacancies available in the boundaries. A number of papers have dealt with the morphology of chromium carbide (M23 C6) precipitated in austenitic stainless steels.1"7 In all these investigations, the carbides were examined in the electron microscope by means of extraction replicas. With this technique, the carbides retain the spatial distribution they had in the bulk sample. However, since the matrix is dissolved in the process, the particles can turn in an unpredictable way; and the orientation relationship between matrix and carbides cannot be established. In this paper the results of studies on extraction replicas and on thinned metal foils are reported. These studies were undertaken to determine the matrix-to-car bide orientation relationship, and to correlate the orientation of the carbides with their morphology. PROCEDURE The material used was an austenitic alloy with 33 pct Ni, 21 pct Cr, balance iron, containing approximately 0.05 pct C. Coupons of 1.25-mm sheet were first solution-annealed at 1050°C for 15 min and air-cooled. Then, to precipitate the carbides, samples were isothermally annealed in the range from 565" to 870°C for times up to several thousand hours. All further specimen-preparation procedures were carried out after the final anneal. Carbon extraction replicas from polished and etched surfaces were made with 10 pct bromine in methyl alcohol.' Thin foils were prepared from punched-out 3-mm-diam disksg which fit into the electron-microscope holder. The disks were prethinned by grinding to approximately 0.5 mm thickness, and then electro-polished in a polytetrafluoroethylene holder1' with a solution containing 5 pct perchloric acid in acetic acid to which 10 g per 1 Cro3 and 5 g per 1 nickel chloride were added (etchant modified from that of Briers et al."). This solution dissolves neither the carbides nor the austenite around the carbides preferentially. By using extraction replicas, electron micrographs and selected-area electron-diffraction patterns were taken from the same carbide arrays. By using thin foils, electron micrographs were made from a grain boundary area containing carbides. Electron-diffraction patterns were then taken from the same area and from each of the adjacent grains separately. In this manner, the orientation of each grain could be determined without interference by the carbide pattern. A peculiarity of extraction replicas should be pointed out. After the matrix is etched away, the carbide arrays float freely in the etching and washing solutions, and are held in place only at the anchoring points in the carbon replica. When the replica is picked up with a screen the carbide arrays tend to flip to one side. Thus, while the surface features are preserved, the original arrangement of the carbides may severely and unpredictably be disturbed whenever the specimen contains large amounts of interconnected carbides. Nevertheless, it is possible to correlate the different morphologies of the carbides with the type of boundary in which they have precipitated. RESULTS 1) Extraction Replicas. Fig. 1 shows that the grain boundaries usually are curved, multicornered surfaces of random orientation. The coherent twin boundaries (which are (111) planes) cut a grain into parallel slices. Incoherent twin boundaries occur at the ends and on the steps of twins and are often narrow, parallel-sided strips which are much longer than they are wide. Different morphologies can clearly be distinguished for the M23Ce carbides precipitated in each of these types of boundaries, and agree well with those observed by kinzel.2 The kinetics of this precipitation has been investigated." The first carbides precipitate in junctions of three grain boundaries and fan out from there into the adjoining boundary surfaces, Fig. 2(a). These carbides are oriented randomly, Fig. 2(b), and become coarser and thicker as annealing time increases. The large-angle grain boundaries are next to fill