Search Documents

By W. B. Morrison

Anderson, King, and Spreadborough present detailed evidence to show what ~aldwin~' has already pointed out, that, over a relatively small grain-size range (Ad"1/2 ^ 10 mm-'I2, d is average grain diameter), yield point data can fit a number of relationships. Part of the difficulty in obtaining data which reflect only the effect of change in grain size on yielding arises from the fact that in varying the grain size, even though great care is taken, other structural changes are almost certain to occur. In iron alloys, these changes may consist of variations in subgrain size, grain boundary ledge density, and degree of carbon and nitrogen segregation at grain boundaries, all of which are difficult to detect and which may affect yielding, primarily through their effect on dislocation generation. Because of the inherent inaccuracy associated with yield point measurements there is little point in using relatively complex equations to fit data, as was done by Anderson et mnl., rather than the simpler, widely used Hall-Petch equation. In compiling their table of data, it is surprising that they did not include results from certain low-carbon steels,31 in which, as illustrated in Fig. 2, the grain-size range is very much larger than in their Armco Iron. The very fine grains in these steels were obtained by a thermomechanical process. Examination by electron microscopy showed that the grains were separated by high-angle boundarie and contained only an occasional subboundary. The data from these steels obeyed the Hall-Petch equation, and it was shown quite conclusively that they did not fit a d-l or (1-lJ3 relationship. Obviously, a much wider range in grain size than used by Anderson et al. is desirable if we are to determine the true relation between lower yield stress and grain size.

Jan 1, 1969

By W. G. Matteson

BENJAMIN L. MILLER, So. Bethlehem, Pa.-In discussing the question personally with Mr. Matteson I have found that he simply proposed this as a suggestion and he recognizes, as well as a great many other oil geologists and oil operators, that to put into practice such a suggestion would mean the overcoming of many difficulties. Yet perhaps it may be possible to overcome the various objections that may be offered. Undoubtedly one of the most serious objections is that of incomplete and inaccurate well records. Faulty records are worse than no records at all. Perhaps, however, definite instructions and insistence on their observation may remedy this defect after a time. THE CHAIRMAN (M. L. REQUA, San Francisco, Cal.).-This subject is a. very important one, but just how far the National Government can go in .taking action is a question: It involves, of course, the question of State rights. California, I .think, has done very well up to date and probably will do better in the future. The law that was passed at the session of the Legislature 2 years ago is working as satisfactorily as anything of that kind can work with so little experience to guide the framers of the statute. We recognize in California the vital necessity of conserving the oil of the State. We have come to the conclusion that there is not as much oil ,in California as we thought there was. In the month of December the State drew on its oil stocks to- the extent of 1,800,000 bbl. and I think that the January statistics will show probably as much more. There is more or less of a.: panic at the present time among the large marketing concerns regarding the question as to where they are going to get their oil for future requirements

Jan 4, 1917

Safety Factor Characteristic Curves. Their Application to Mine Hoisting Ropes. (Paper by W. A. Boyer, Transactions AIME, 199, 989; Mining Engineering, October 1954. Discussion by B. E. Grant.) ............................................................................................................................. 1101 The Use of Wooden Rock Bolts in the Day Mines. (Paper by Rollin Farmin and Carville E. Sparks, Transactions AIME, 196, 922; Mining Engineering, September 1953. Discussion by Edward Thomas.) ................................................................................................................................. 1101 An Analysis of Mine Opening Failure by Means of Models. (Paper by Bernard York and John J. Reed, Transactions AIME, 196, 705; Mining Engineering, July 1953. Discussion by J. P. Zannaras.) ... 1102 B — Minerals Beneficiation Flotation and the Gibbs Adsorption Equation. (Paper by P. L. de Bruyn, J. Th. Overbeek, and R. Schuhmann, Jr., Transactions AIME, 199, 519; Mining Engineering, May 1954. Discussions by W. E. Ewers and Masayoshi Wada.)........................................................................................... 1103 Manganese Upgrading at Three Kids Mine, Nevada. (Paper by S. J. McCarroll, Transactions AIME, 199, 289; Mining Engineering, March 1954. Discussion by J. Bruce Clemmer, J. B. Rosenbaum, and C. H. Schack.)............................................................................................................. 1105 A Physical Explanation of the Empirical Laws of Comminution. (Paper by D. R. Walker and M. C. Shaw, Transactions AIME, 199, 313; Mining Engineering, March 1954. Discussions by Dimitri Kececioglu, George B. Clark, and Fred C. Bond.) ......................................................... 1106 F — Coal Underground Electrocarbonization of Coal and Related Hydrocarbons. (Paper by T. C. Cheasley, J. D. Forrester, and Erich Sarapuu, Transactions AIME, 199, 908; Mining Engineering, September 1954. Discussions by John G. Tripp and James L. Elder.)....................................................... 1108 Longwall Mining and Mechanization, with Special Reference to Nova Scotia. (Paper by Frank Doxey, Transactions AIME, 199, 701; Mining Engineering, July 1954. Discussion by Louis A. Turnbull.) ........................................................................................................................................ 1109 Cleaning Various Coals in a Drum-Type Dense-Medium Pilot Plant. (Paper by M. R. Geer, W. A. Olds, and H. F. Yancey, Transactions AIME, 196, 696; Mining Engineering, July 1953. Discussion by John Griff en.)................................................................................................................................. 1110 Frontiers in Heat Extraction from the Combustion Gases of Coal. (Paper by Elmer R. Kaiser, Transactions AIME, 199, 304; Mining Engineering, March 1954. Discussion by G. A. Vissac.) ............ 1112 Exploration of the Oaxaca Coal Fields in Southern Mexico. (Paper by Luis Toron and Salvador Cortes-Obregon, Transactions AIME, 199, 505; Mining Engineering, May 1954. Discussion by John D. Price.).................................................................................................................. 1113 H — Industrial Minerals Alkali Reactivity of Natural Aggregates in Western United States. (Paper by William Y. Holland and Roger H. Cook, Transactions AIME, 196, 991; Mining Engineering, October 1953. Discussions by Dexter H. Reynolds and W. L. Merritt.) ......................................................... 1114 Characteristics of Titaniferous Concentrates. (Paper by L. E. Lynd, H. Sigurdson, C. H. North, and W. W. Anderson, Transactions AIME, 199, 818; Mining Engineering, August 1954. Discussion by D. R. Grantham.)........................................................................................................................ 1116

Jan 1, 1955

By John C. Loretta

INTRODUCTION Organizations that regularly use project management services will almost certainly have their own views on the preferred systems and procedures. This chapter, therefore, describes Project Management for the personnel of groups not familiar on a regular basis with project management and deals with the basic questions that these groups can be expected to ask, such as: - What is project management? - Why is it needed? Project Management is the planning, implementation and monitoring of the Engineering, Procurement and Construction activities that are necessary to complete the project in the most economic manner. In the case of a crushing and grinding plant, completing the project would mean bringing it into full operat ion. Engineering is the design work for the purpose of producing drawings and technical specifications for Construction together with technical specifications and quantities for Procurement. Procurement is the arranging of con- tracts so that equipment, material and labour are brought as required to the construction site. Construction covers the on-site activities that bring together the components of Engineering and Procurement so as to arrive at a finished plant. Need & Cost Benefits Project Management systems are needed to allow progress and expenditures to be monitored so that any significant deviations from the plan can be identified and the appropriate corrective action taken. In this way, Project Management is able to give continual updated answers to the Owners broad questions. - What am I getting? - What will it cost? - When will it be ready? The need for Project Management is not always immediately apparent, a common belief being that the existence of the three components -Mining Company - Equipment Supplier - Construction Company - is sufficient to get the job done without a formal project management group. This trio

Jan 1, 1982

By R. R. Klimpel Discussion by C. C. Harris, L. G. Austin

C. C. Harris (Columbia University) — The authors ' have presented relationships for the random division of a magnitude into r + l parts taking account of the order of selection. Interpreting their model in comminution terms, their Eqs. 7, 9 and 11 refer to the one-dimensional case; that is, to the subdivision of a long thin rod at random. It is assumed that the fragments may be indefinitely small. Real materials, however, are limited in the degree of subdivision which can be attained through the intervention of practical restrictions. One in fine grinding is the depletion of microflaws as material becomes finer. Another is the

Jan 1, 1969

US 4,183,794 - Electrowinning zinc from a zinc sulfate solution produced by leaching zinc ore with sulfuric acid. The leach liquor is subjected to electrolysis in a first cell having an insoluble anode to deposit primary zinc on the common electrode. The coated electrode is transferred to a second cell having an alkaline electrolyte, and electrolysis is effected in the second cell to transfer zinc from the common electrode to the second cell cathode in a spongelike form which is readily stripped. R.H.C.L. Ross. Jan 15, 1980. 10 pp. (204-119). Filed: 12-22-77 (863,190). Same: Canadian 1,051,820, dated Apr. 3, 1979.

Jan 1, 1982

By R. F. Slack, J. C. Draper, J. A. Younkins

In 1959, the Duquesne Light Co. was faced with the problem of moving more than 40 million tons of bituminous coal in Greene County, Pa. The coal had to travel a distance of about 4 ½ miles from a new mine portal in Rocky Run Valley to the company preparation plant and loading facilities on the Monongahela River. After careful study of this immense transport problem, Duquesne decided that the belt conveyor system described in the following pages offered the best solution. This system, now in operation, is probably one of the four or five longest permanent overland conveyor systems in existence. The general layout of the entire system is shown in Fig. I. A detailed description of the salient features of the system is presented below. THE MINE The valley of Rocky Run where the system begins is very, very narrow and very steep. It was chosen as the site of Duquesne's new mine portal because it was the only place on this particular property where the Sewickley coal seam cropped out. The valley also had two other advantages. First, it fronted on a state road and, second, it offered a site where some 4 million gallons of water could be stored for use in dust-allaying sprays needed in the mine. The company elected to construct a drift mine in the valley because this would require neither the hoisting time of a shaft mine nor the walking time of a slope mine. As part of the mine construction project, the valley was leveled by relocating its stream and filling its center with material cut from each side.

Jan 11, 1966

The practice of fine-grinding is now being so succeesfully carried on in some fields, notably in West Australia, and its advisability has been so frequently pointed out,l that the matter in this paper is not put forward as new; its chief object being to call attention to the importance of fine-grinding in the treatment of comparatively low-grade oree. I' have been engaged daring the last five years in the cyanide-treatment of ores in the Ohinemuri district (North Island), New Zealand, and I consider that, in the near future, extremely fine-grinding (almost sliming) will become a very im-

Jan 1, 1906

By G. L. Gates

The comments by George L. Gates are appropriate to the characteristics that we sought to feature in our study and they are appreciated by the authors. In our laboratory deposition tests the smoothness of the surface seemed to be more important than the type of surface. However, we also noted that even where very smooth glass, plastic or polished metal coupons were used, scale deposition still occurred though the rate varied. Much more information is needed, however, and new work to solve the mineral scale deposition problem by mechanical and chemical means is expected to continue.

By G. Sachs, G. Espey

It is well known that high residual stresses are created in tubing by the sinking process, in which no internal tool or mandrel is used.l-4 In this process, the wall thickness is usually slightly increased.4,5 In tube drawing with a plug, the residual stresses are gradually reduced with increasing reduction of wall, and, by the conventional approximation methods of stress measurement, no stress is detected in tubing in which the wall reduction is over 50 per cent of the total reduction in cross-sectional area.l,6 It has also been observed that higher stresses are set up by the use of wide-angle dies than by acute dies.? 'he actual stress distribution in drawn tubing has been investigated by a few workers,7"9 but has not been related to the conditions of the drawing process. Some attempts have been made to correlate accelerated cracking tests for stresses in brass products with the magnitude of the circumferential stresses and the condition of the metal. l-10 Materials and Preparation The material used in this experiment was commercial cartridge-brass (70 per cent Cu, 30 per cent Zn) tubing in the straightened and annealed condition.† This tubing was of various outside diameters and had a wall thickness of 0.032 in. It was sunk to 1/2-in. outside diameter by means of an experimental 10,000-lb. hydraulic draw-bench, with a maximum drawing speed of 8 ft. per minute. All dies were of 1/2-in. diameter. Various die materials and contours were used in order to study the effect of die design on residual stresses in the tubing; the specifications for the dies are given in Fig. I. Castor oil was used throughout as lubricant. Chattering occurred in sinking some of the tubing, particularly when dies having the more acute angles were used, but the tubes showing chatter marks did not differ markedly from those with a smooth surface regarding the magnitude of residual stress. The source of the chattering has not yet been revealed. The wall of the tubing becomes thicker during s nking, as previously observed.4,5 The increases in wall thickness were 3, 7 and 9.5 per cent on the average for 6, 20 and 33 per cent reductions in diameter, no effect of the contour being noticeable. The reductions mentioned throughout this investigation do not consider this fact, but are reductions of the outside diameter. For the evaluation of the residual stress two fundamentally different methods were used. The approximation methodl,ll of splitting a certain length of tubing was employed to obtain a bird's-eye view of the effect of various drawing conditions on the circumferential stress measured by the diameter change occurring On splitting. For

Jan 1, 1942

By G. Sachs, G. Espey

It is well known that high residual stresses are created in tubing by the sinking process, in which no internal tool or mandrel is used.l-4 In this process, the wall thickness is usually slightly increased.4,5 In tube drawing with a plug, the residual stresses are gradually reduced with increasing reduction of wall, and, by the conventional approximation methods of stress measurement, no stress is detected in tubing in which the wall reduction is over 50 per cent of the total reduction in cross-sectional area.l,6 It has also been observed that higher stresses are set up by the use of wide-angle dies than by acute dies.? 'he actual stress distribution in drawn tubing has been investigated by a few workers,7"9 but has not been related to the conditions of the drawing process. Some attempts have been made to correlate accelerated cracking tests for stresses in brass products with the magnitude of the circumferential stresses and the condition of the metal. l-10 Materials and Preparation The material used in this experiment was commercial cartridge-brass (70 per cent Cu, 30 per cent Zn) tubing in the straightened and annealed condition.† This tubing was of various outside diameters and had a wall thickness of 0.032 in. It was sunk to 1/2-in. outside diameter by means of an experimental 10,000-lb. hydraulic draw-bench, with a maximum drawing speed of 8 ft. per minute. All dies were of 1/2-in. diameter. Various die materials and contours were used in order to study the effect of die design on residual stresses in the tubing; the specifications for the dies are given in Fig. I. Castor oil was used throughout as lubricant. Chattering occurred in sinking some of the tubing, particularly when dies having the more acute angles were used, but the tubes showing chatter marks did not differ markedly from those with a smooth surface regarding the magnitude of residual stress. The source of the chattering has not yet been revealed. The wall of the tubing becomes thicker during s nking, as previously observed.4,5 The increases in wall thickness were 3, 7 and 9.5 per cent on the average for 6, 20 and 33 per cent reductions in diameter, no effect of the contour being noticeable. The reductions mentioned throughout this investigation do not consider this fact, but are reductions of the outside diameter. For the evaluation of the residual stress two fundamentally different methods were used. The approximation methodl,ll of splitting a certain length of tubing was employed to obtain a bird's-eye view of the effect of various drawing conditions on the circumferential stress measured by the diameter change occurring On splitting. For

Jan 1, 1942

By H. C. Chao, L. H. Van Vlack

Small MnS inclusions with known crystallographic orientations were placed inside powder compacts of low-carbon steel. After the metal was axially campressed with negligible end friction, the deformstions for the metal and the inclusions were compared. The MnS inclusions deformed more when the [100] direction was aligned with the compression axis than when the [111] direction was parallel to this axis. The deformations of the inclusions in the two principal radial directions were equal for each of the above orientations. Inclusions with [110] compression alignments did not deform with radial symmetry. The relative deformation of the inclusion and metal was closely dependent upon the relatiue hardness of the two phases. The relative deformation of the two phases was not sensitive to the rate of deformation. RECENT studies by the authors1.&apos; suggested that the plastic deformation of MnS in steel would probably be highly sensitive to the orientation of the inclusions and to the temperature of the metal. This paper reports an investigation of these factors upon MnS behavior within steel. Manganese sulfide (MnS) possesses an NaCl-type structure and typically has extensive (l10) {110} slip as a separate (noninclusion) crystal.&apos; A secondary slip system, ( l 10) { l l l}, has also been observed where the major slip system is restricted. In general, MnS inclusions must be rated as a highly deformable second phase.3 The amount of sulfide deformation varies, however, with several composition and processing factors. Some of these have been only partially assigned. For example, it is known that minor amounts (<0.01 pct) of silicon within free-machining steels will increase the amount of MnS deformation,4 but the mechanism of the added deformation can only be surmised at the present. Manganese sulfide and steel have sufficiently comparable deformation characteristics so that slip which is started in steel may be continued through the sulfide inclusions and back into the steel if the crystal orientations are favorable.5 A more detailed discussion of previous work on the plastic deformation of NaC1-type crystals and on the plastic deformation of inclusions within a metal is given in Chao&apos;s work.6 EXPERIMENTAL PROCEDURE The manganese sulfide which was used in this study was prepared by previously described methods.&apos; Single crystals of MnS, both as cleavage cubes and as spheres, were oriented within steel powder compacts so that the desired crystal directions were parallel to the direction of axial compression. A four-stage hydrostatic compaction procedure was used and involved the following steps. In the first stage part of the powder was placed in a metal die 1 in. in diameter with a thick (1 in. OD, 5/8 in. ID) rubber liner which had one end plugged. The steel powder was hand-rammed, making it as dense as possible before placing a carefully sized MnS crystal (either as a sphere or as a cube) near the center. The crystal was oriented with the chosen direction vertical; viz., [001], [011], or [111], with the aid of a X10 microscope. A pair of tungsten wire threads 0.020 in. in diameter was inserted along the side of this (&apos;core compact" to locate the desired plane after the compression tests. After the crystal was positioned in the center of the die, more powder was added and carefully rammed by hand. The die was then capped with a rubber plug of the same hardness and thickness as that of the liner. The whole assembly as shown in Fig. 1 was compacted by a ram load of 54,000 lb (about 70,000 psi). In the second stage a smaller, 3/4-in, rubber-lined die was used to give a stress of approximately 120,000 psi. The above process was repeated with the initial compact serving as a core for a larger compact. The final product after sintering was a cylinder 1 cm long and 1 cm in diameter, having a density of 7.54 g per cu cm. This was close to the theoretical density since the metal contained a non-metallic phase. There was no evidence of MnS deformation during the hydrostatic compaction or subsequent sintering. Elevated-temperature hardness data were obtained by procedures previously described.2 Compression tests for inclusion deformation utilized the cylinders which were described above. The critical problem in these tests was the lubri-

Jan 1, 1965

By E. S. Machlin, W. R. Yankee

IN a previous study1 of the effect of heating com-mercial titanium in air on its subsequent friction coefficient against other metals, as well as itself, it was found that the friction coefficient markedly decreased from a value of about 0.7 to about 0.3. A tentative explanation was given that surfaces normally produced at room temperature are not contaminated sufficiently to prevent seizing or welding of the titanium to the softer mating metals. The latter tend to cleanse themselves during rubbing over the harder titanium. It was thought that the lack of a contaminant protective film on the titanium was due to the high solubility of titanium for oxygen and nitrogen and hence an inability to form a contaminant oxide or nitride. This explanation requires the ratio of the surface absorption rate to the diffusion rate to become much lower at room temperature than it is at high temperatures. In order to check the phenomenon further, commercial titanium specimens were nitrided or oxidized at 800°C for 20 hr in flows of prepurified N2 and 01, respectively, at about 1/2 in. H2O above atmospheric pressure. Friction runs were made in argon using a freshly cut copper hemisphere (cut in argon) on surfaces cut successively into the diffusion layers in the titanium (cut in argon) using the techniques described in a previous publication.&apos; DPH values (100 gram load) were made as a function of depth into the diffusion layer using a Tukon tester. Also, micrographs were taken at separate cross sections to indicate the diffusion layers. The results obtained are presented in Figs. 1 and 2, which show the "static" friction coefficient vs hardness for the nitrided and oxidized specimens, respectively. A separate measurement of the friction coefficient of clean copper vs iodide titanium also was made. From results reported in the literature&apos; giving the oxygen and nitrogen contents as functions of the hardness, cross plots were made showing the friction coefficients as functions of the amount of interstitial solute. These plots are given in Figs. 3 and 4. From micrographs of the diffusion layers and the phase diagrams, it was deduced that the data in Figs. l through 4 correspond to the single phase a region. The points observed on the compound regions have been excluded from the figures. It is apparent that nitrogen or oxygen in solution in the a titanium markedly affects the friction coefficient against a softer mating metal. Discussion of Results These results are extremely interesting from both a practical and theoretical viewpoint. The theoretical implications will be discussed first. According to Bowden, the friction coefficient should be given to a good approximation by the relation where a is the fraction of contact area that has welded, a is the shear strength of weaker component, and H is the hardness of softer component. Using this relation alone, it is difficult to understand the results because none of the terms should be affected by a variation in the oxygen or nitrogen content of the harder and stronger metal, titanium. Even if the ratio of S/H for titanium is used in Eq. 1, the ratio has been shown to be independent of oxy-gen or nitrogen content.&apos; If a more rigorous equa-tion is used combining Eq. 1 and a result given pre-viously" for the case where welding is absent, then the relation obtained is µ = a S/H + (1-a) a W aß/H where a is constant and Waß is the work of adhesion between the two metals comprising the friction couple. This relation states that if a is less than 1/2 or so, variation in the work of adhesion Waß between copper and the titanium should affect the friction coefficient markedly. It is reasonable to expect that the work of adhesion will depend on the oxygen or nitrogen content of the titanium. Available data4 show that clean metals and oxides have much lower works of adhesion than the same metals against the

Jan 1, 1955

By Richard Addison, Ronald O. Cranor

Tailings dam construction and operation of Rosario Dominicana&apos;s gold/silver mine in the Dominican Republic is described. Impoundment of 8.5 kt/d of cyanide-process tailings is required in an intensive agricultural area which is also an earthquake and high rainfall zone. The earthfill embankment dam, incorporating internal gravel drains, is described together with methods of construction used. Methods of tailings transport, solution reclaim, and runoff water diversion that have evolved are discussed.

Jan 1, 1982

COMMITTEES Committee on Arrangements DAVID H. BROWNE, Chairman LAWRENCE ADDICKS THOMAS T. READ P. E. BARBOUR BURR A. ROBINSON GEORGE D. BARRON F. T. RUBIDGE KARL EILERS E. MALTBY SHIPP LOUIS D. HUNTOON BRADLEY STOUGHTON H.A. MEGRAW EDWARD B. STURGIS ARTHUR L. WALKER

Jan 4, 1917

Jan 1, 1900

By H. Bloom, H. E. Hawkes

STREAMS and rivers are the principal channels into which the weathering products of rocks and their contained ores are funneled. The inorganic load of a stream system is a crude sample of all the earth materials in the drainage basin of the stream, and the heavy mineral assemblage of sediments is one of the oldest and most successful guides to certain kinds of bedrock ore in unexplored terrain. Early application of this method was made possible by the ease of separation and identification of heavy minerals in the field with the simplest equipment. Water analysis for traces of base metals became a practical possibility about eight years ago with the development of rapid chemical tests that could be carried out at the field site.&apos; , Since that time the water method has been widely used in mineral reconnaissance, and a substantial number of discoveries have been reported. Here again, the techniques developed for this work were relatively simple and could be performed easily at the field site. Sediment analysis by chemical methods, as distinguished from mineralogical, has received less at- tention. Some experimental work was done by Lovering and others," but to the authors&apos; knowledge, chemical analysis of sediment samples has not been used in routine exploration programs until very recently. In spite of the obvious promise of this method, it was not pursued vigorously because of the lack of a simple and portable chemical test that could be used conveniently at the field site or in a field camp. Procedures that had been developed for trace analysis of soils all called for a rigorous chemical attack with hot acids—tests more conveniently applied in processing large volumes of routine soil samples at an established field headquarters. Recently an extremely rapid and simple test was developed by Bloom.4,5 The extractant used in this procedure is a cold solution of ammonium citrate. Elements measured are the heavy metals, principally zinc, lead, and copper. This method differs from the established procedures for soil analysis in that it measures only a small fraction, about 5 pct, of the total metal content of the sample. It has been found, however, that the significant pattern of metals in the sediments of streams below a base-metal deposit can be brought out as well and sometimes better by this simple cold-extraction procedure than by the more tedious methods requiring hot acids. To understand fully the significance of the relation between the readily extractable and the total

Jan 1, 1957

Jan 1, 1951

Jan 1, 1951

By D. H. Yardley

Diversion of the American Falls of Niagara to permit investigation of ways and means to stabilize the falls while retaining or improving its natrual attractiveness is the geoengineering work that has received greatest public attention this year. The falls are re- treating slowly as rock falls occur while talus de- posits at the base have increased in size. One of the noteworthy questions is whether the talus should be removed-i.e. is it providing support to the base, and so what will happen if it is removed? Certainly the appearance would be improved if the talus were taken away. Geoengineering studies involve mapping of joints, stress measurements, core work and rock sampling and testing, Present work will provide data and interpretation for design of a long term stabilization system, Once basic information is obtained, water will be returned to the normal channel until such time as the detailed design is decided upon. The falls will then be diverted a second time while necessary work is performed. A number of site-environmental studies were carried out for the location of nuclear power plants. These projects involve geology, foundation engineering, hydrology, seismology, meteorlogy, marine geology (in some cases), rock mechanics and occasionally blast monitoring. In one case (investigated by Dames & Moore) the site area was underlain by caverns in limestones at shallow depths but with no surface expression. The geotechnical problems consisted of determining proper spacing of drill holes to locate caverns. Spacing was dependent on the smallest size of cavity that could constitute a support-stability problem for the plant. The finite element method of analysis was used to determine stress conditions around cavities of various size and depths, to assist in determining critical parameters.

Jan 1, 1970