Search Documents

By H. Y. Yancey, B. M. Bird

One of the problems studied by the U. S. Bureau of Mines in cooperation with the University of Washington has been the re-treatment of table middlings. Hydraulic classification has given the best results. Instead of using the classifier to prepare the feed to the tables, as has been the practice for many years in ore dressing, it is used to separate part of a middling product that cannot be re-treated successfully on the table. Middlings are desirable in a table plant because the separation according to specific gravity is incomplete; that is, in the products of the table there is always an overlapping of free particles of coal and refuse that can be distinguished with heavy liquids such as are used in the float-and-sink test. The causes of this overlapping may be divided into two groups, those outside the table separation itself and those inherent in the table separation. The first of these groups includes, among other causes, the following: (1) poor adjustments of the table, (2) overloading or underloading the table, (3) irregularities in the quantity and quality of the feed, (4) irregularities in the power and water supply, and (5) a vertical dancing motion of the table deck due to weak foundations. These causes of overlapping are largely unnecessary in a properly designed and constructed plant; but whenever they are present they materially affect the character of the middling product, and hence the problem of re-treatment. The other group includes three additional causes: (6) small differences in specific gravity between coal and impurities, (7) a size-specific-gravity relationship of the coal and refuse particles in the table feed such that the sizing action of the table opposes the separation according to the specific gravity, and (8) shapes of particles that prevent a separation. The sixth, small differences in specific gravity, may be a very important reason for an incomplete separation. The change in specific gravity from coal to shale is always gradual and the designation of one part as coal and another part as refuse is arbitrary. If some specific gravity, such as 1.45, is chosen as the dividing point between washed coal and refuse,

Jan 1, 1930

By Donald A. Brobst

The minerals barite (BaSO4) and witherite (BaCO3) are the chief sources of the element barium and its compounds needed for many industrial processes and products. Barite, the principal ore mineral, is found the world over and is abundant and widely distributed throughout the United States.3 Witherite is much less common than barite, though more desirable in many ways as a raw material for the production of barium chemicals. England is the chief producer of witherite. Witherite is not mined in the United States at the present time, but it has been mined with barite from a deposit at El Portal, California. Barite is also called barytes, tiff, cawk, or heavy spar. Ordinarily it is a heavy mineral that crystallizes in the orthorhombic system. It is colorless, white, or gray, and transparent to opaque. In some deposits barite is black, yellow, brown, red, green, or blue because of included impurities. The streak is white and the luster vitreous to resinous or pearly. The specific gravity of pure barite (65.7 pct BaO and 34.3 pct SO3) is calculated to be 4.5, but inclusions and impurities in natural barite may reduce this value considerably. Well-formed crystals are generally tabular and have three cleavages. The barite of many deposits, however, has an uneven fracture and an apparent cleavage caused by separation along planes between successively deposited layers. The hardness is 2.5 to 3.5 on Mohs' scale. Commercially the terms "hard" and "soft" are used to refer to ease of grinding. Barite is relatively insoluble in water and acid, and thus can be used as a chemically inert material. Witherite, the natural carbonate of barium (77.7 pct BaO and 22.3 pct CO2), crystallizes in the orthorhombic system. The fracture is uneven and the luster is vitreous to resinous. The hardness is 3 to 3.5. The specific gravity of the pure mineral is calculated to be 4.29. It is transparent to opaque. The color is ordinarily white, gray, yellow, brown, or green. Geology and Distribution of Deposits Workable deposits of barite are widely distributed throughout the world in many geologic environments in sedimentary, igneous, and metamorphic rocks. Most deposits can be classified into three main types: (1) vein and cavityfilling deposits; (2) bedded deposits; and (3) residual deposits. 1. Vein and cavity-filling deposits are those in which barite and associated minerals occur along faults, gashes, joints, and bedding planes, and in breccia zones and solution channels. They also occur in various collapse and sink structures in limestone. Sharp contacts of the veins and cavity fillings with wall rocks are common. Barite cements fault and collapse breccia by replacement of the matrix or by filling voids. Large-scale replacement of the wall rocks beyond ore-controlling structures is rare. Barite in vein and cavity filling deposits is generally dense, "hard," and white to gray. Associated minerals are fluorite, calcite, ankerite, dolomite, quartz, and many sulfide minerals, especially pyrite, chalcopyrite, galena, and sphalerite. Gold, silver, and rare earth minerals occur with barite in some deposits in the western United States. Barite is also a gangue mineral in metallic ore deposits but production as a byproduct from such deposits will be affected by many economic factors. The host rocks are igneous, sedimentary, and metamorphic rocks of pre-Cambrian to

Jan 1, 1960

By V. R. Degner

The trend in both the metallic and nonmetallic mining industry is toward processing increasingly higher tonnages of lower grade ores, thereby resulting in a growing interest in progressively larger volume individual machines in the flotation circuit. Because of the relatively high cost of large flotation machine development and evaluation, it is important to establish a rational basis by which the existing smaller flotation machine experience can be extrapolated to establish the configuration of the next larger family of flotation machines with a minimum of development modification in the field. This Paper reviews the R&D approach used in translating smaller flotation machine experience to the configuration of a 28.3 m3 (1000 cu ft) induced air machine. Internal cell hydrodynamic principles, which governed this extrapolation, and cell (liquid) surface and froth management considerations will be reviewed, and prototype machine mill tests will be summarized.

Jan 1, 1981

By Bernard Moore

THE last few decades have witnessed the introduction of many new nonmetallic mineral products and changes in the use of many of those already well known. Among these is diatomite, formerly employed as a mild abrasive and, at one time, as the absorbent material in dynamite. Now nearly 100,000 tons a year are mined and milled into such things as filter aids, cement admixtures, insulants, fillers, absorbents, cosmetics, cleansers, etc. Pumice, commonly regarded as only an abrasive, is now also employed as an insulant, as light-weight aggregate and as a concrete admixture. With increasing use of insulants, light-weight aggregates, and acoustic stuccos and plasters in the building trades, both these mate-rials should find increased application. Very large deposits occur in eastern Oregon and have been studied by the U. S. Geological Survey in cooperation with the Oregon State Mining Board.

Jan 1, 1934

By M. L. Brashears

IN the last 15 years industrial use of ground water has more than doubled, and in 1951 amounted to 5 billion gallons per day. A similar sharp increase in the utilization of ground water for irrigation and public-water supply occurred in the same period. In many areas rapid increase in withdrawal from wells has taken place almost entirely unhampered by regulatory control and with little or no integration of effort. As might be expected, the chief interest in many regions has been maximum production rather than sustained perennial yield. As a result, widespread depletion of underground reservoirs and deterioration of the quality of the water stored in them has taken place in many areas, even though total pumpage in the United States is far below ultimate potential. Of even more concern is the fact that excessive withdrawal has drawn salt water into the reservoirs beneath many heavily populated centers along the Atlantic, Gulf, and Pacific coasts, causing costly abandonment of pumping plants.' Many hydrologists expect that consumption of water will rise rapidly in the near future, and some predict that industrial requirements will more than double in the next decade.2,3 Thus it appears likely that the draft on many already heavily pumped underground reservoirs will be greatly increased and the search for additional sources of usable ground water intensified in years to come. In view of this, industry as a whole will be forced more and more to recognize the potentialities and limitations of ground-water reservoirs and to utilize them more effectively to prevent costly water shortages and disruption of production. Through painful experience, some industries are already well aware of the need for effective water utilization, and have managed individually or through joint effort to check trends threatening to deplete underground reservoirs completely or to impair the quality of the water. Various remedial measures have been used to bring about successful management of local or regional ground-water resources. Of these, replen-ishment of aquifers by recharge wells or basins has played an important role in overcoming some ground water problems. Artificial recharge of underground reservoirs by water spreading has been practiced successfully in the United States for many years. In the West it has become an important method of salvaging flood run-off for irrigation of crops and maintenance of public water-supply reserves, and it is used to some extent in parts of the East. Artificial recharge by means of wells, on the other hand, is a relatively new development. Until recently it was employed in only a few areas, principally along the East coast. For the last few years, in the ever increasing search for additional water supplies, industry has had greater recourse to this method. Utilization of recharge wells to control the temperature and quality of underground water supplies is also being considered seriously. Operation of recharge wells, like water spreading, is governed largely by local conditions. It requires water relatively low in turbidity, whereas in some areas water spreading has been used successfully with water of high turbidity and silt content. However, water spreading must be employed in large areas and can be carried on effectively only where aquifers crop out at the surface. Recharge wells can be used in limited space. Recharge wells are similar to production wells except that the water flows in the opposite direction. Thus any water-bearing bed that will yield water to wells may be recharged by wells. Often, however, the water available for recharge is of a different character and temperature from that existing in the ground-water reservoir and if transmitted directly underground from a recharge well to a production well might require expensive or difficult treatment before it could be used. Fortunately the physical characteristics of reservoir beds, which control the movement and behavior of ground water, are generally not homogeneous. Moreover, the movement of ground water is very slow because of the frictional resistance of the reservoir beds. By taking full advantage of hydrologic and geologic conditions, it is therefore possible in many instances to bring about favorable changes of temperature and dilution as the water moves from the recharge wells underground to the production wells. Furthermore, if the natural quality or temperature of ground water is unfavorable for industrial purposes, recharge wells may be used to introduce water of more favorable quality or temperature into the ground-water reservoir. When water is discharged into a recharge well, the head in the well is increased. Because of this, a cone of elevation is produced on the water table or the artesian pressure surface in the area surrounding the well. The cone of elevation is similar to the cone of depression produced around a pumping well except that the apex of the cone is above the water table or artesian pressure surface. Thus if a recharge well and a production well tapping the same water-bearing bed are close together, as would be the case at many industrial plants, some of the water discharged from the recharge well would be drawn into the production well within a short time. Under such conditions it is apparent that water of unfavorable temperature and chemical characteristics should not be used for recharging. The more important ground-water reservoirs in the United States often consist of alternating layers of impermeable beds and porous material that will yield water readily to wells. Physical characteristics of individual beds in a ground-water reservoir may not persist over great distances, the impermeable layers grading into beds that will yield large quantities of water. Thus the water-yielding material in underground reservoirs, whether large or small,

Jan 1, 1954

By H. J. Levinstein, H. J. Guggenheim

RbFeF3 is a transparent ferromagnet with a large faraday rotation which permits the direct observation of magnetic domain structures in bulk crystals. If the position of dislocations within the crystal were known a study of domain wall dislocation interactions would be possible. In this paper an etch pitting solution is described which gives a one-one correspondent between the etch pits and the dislocations intersecting the (100) surfaces of RbFeF3 crystals. In addition, RbFeF3 is shown to have sufficient plasticity so that known arrays of dislocaticms can be put into the crystal. It is concluded that RbFeF, is an ideal material for the investigation of domain wall dislocation interactions. THE influence of lattice defects on the motion of domain walls in ferromagnetic materials has been studied extensively both theoretically and experimentally.4 The experimental data obtained has been qualitative in nature due to the lack either of a quantitative knowledge of the magnetic domain array in the material or of the nature of the dislocation configuration in the material. At room temperature RbFeFJ has the cubic perovskite structure. It is ferromagnetic below 86°K.5,6 It is also transparent and has a large faraday rotation in the magnetic state.7 The domain structure of this material is observable in three dimensions in crystals which are millimeters in thickness.' Since RbFeF3 satisfies the requirements of having an easily visible three-dimensional magnetic domain structure, it was of interest to determine if the dislocation structure of the material could be determined and if the material was sufficiently plastic so that dislocations could be introduced into the as grown crystals. This is a report of the results of that investigation. EXPERIMENTAL PROCEDURE The crystals of RbFeFs used in this experiment were grown by a technique described elsewhere.5 In order to obtain flat strain-free surfaces, the samples were first cut to the crystal orientation desired and the surfaces were polished by employing standard metallographic techniques. The samples were then immersed in a solution of 1 to 3 g of KOH in 100 ml of water. This solution removes the damaged surface layers uniformly leaving a film on the surface of the sample. Etch pits are obtained by immersing the sample in an approximately 50-50 solution of 30 pct peroxide and concentrated acetic acid. The film formed during the KOH treatment turns deep red in color in the etching solution and flakes off the sample. The etching time required depends upon the pit size desired and

Jan 1, 1970

By Eizo Yabuuchi, Yukito Imanaga

INTRODUCTION In treatment of mine drainage, it is well known that the neutralization by calcium carbonate is far better than by slaked lime because of cheaper cost and better precipitability of its deposit. However, in case of iron ion contained in the mine drainage consists of ferrous salt, the ferrous salt must be oxidized to ferric salt before neutralization, because the ferrous salt does not react with calcium carbonate. At Yanahara Mine, during the period of 1950 through 1956, ferrous ion in the mine drainage had been oxidized to ferric ion, simultaneously neutralized by adding calcium carbonate into the aerated drainage. During the period of 1961 through 1974, after passing through many kinds of treating methods, the neutralization had been carried out by addition of calcium carbonate into the drainage after oxidized its ferrous ion to ferric by using nitrous gas as an oxidizing catalyzer. Meanwhile we had made an experiment on the oxidation of ferrous ion by utilizing iron bacteria, and developed a method which oxidized ferrous ion in large quantities briefly by cultivating and concentrating iron-oxidizing bacteria. Since 1974, we have been operating successfully for treating the drainage at Yanahara Mine by means of utilizing these bacteria.

Jan 1, 1976

By D. L. King, B. A. Schepman

A number of unique thickener mechanism designs with the operating results achieved in various installations are discussed. These unusual designs include new types of raking arms, lifting devices, and feed-wells employed to obtain higher underflow densities and minimum operator control or improved overflow clarity. Several installations of large thickeners in which the underflow lines pass upward through the center to eliminate tunnels are reviewed. The location of the lines and pumps with the maintenance and operating records are included. Several types of automatic lifting device controls are used to provide storage in the thickener. Some of the installations employing underflow density controls are achieving excellent operating results. Thickeners or sedimentation basins are used in minerals beneficiation plants for three basic purposes. These are 1) Concentration, or to raise the density of a liquid-solids slurry. 2) Clarification, or removal of finely divided solids from a slurry. 3) Hydroseparation, or removal of a specific fraction of solids from a slurry. The concepts that control the size and configuration of basins used for these purposes are different. Likewise, different equipment is properly employed to accomplish these various objectives. The pattern of liquid and solids flow in the clarification zone of a sedimentation basin used for thickening or raising the density of a pulp normally is not critical. That is, the solids normally will drop or plunge to the bottom quite readily, and the liquid separates itself from these solids so as to overflow the basin in a relatively clear condition. When clarification or removal of finely divided particles is to be accomplished, the flow patterns in the basin are extremely important. The velocity of the incoming stream must be dissipated and the liquid flow distributed ]In the tank so that the feed is not divided into streams that flow directly to the overflow carrying the fine:ly divided solids that are to be removed. Similarly, the configuration of the arms that provide the raking and thickening of the pulp is not as important in basins primarily devoted to clarification. In thickening, the design of the arms and the manner in which the pulp is moved or worked, can contribute appreciably to the thickening process and achievement of a higher density underflow. THICKENING As the grade oi ore bodies throughout the world generally decreases, and chemical processes, hydro-metallurgy, and other more refined methods of minerals beneficiation are required, problems in thickening become more acute. Difficult operating conditions, previously encountered only occasionally in thickening metallurgical slurries, or clarifying process streams in the mill, are now the rule rather than the exception. Fig. 1 illustrates some of the different types of raking arms that are successfully achieving the desired goals in pulp thickening. The conventional raking arms consist of a relatively simple truss with the blades attached to the bottom chords. This design provides proper Concentration of many 'normal' slurries. A modificaiion of this design as shown in the center is being used with excellent results on large thickener basins where it is desirable to have a

Jan 1, 1962

By Philip M. McKenna

WHEN a new material becomes available to industry, it is useful to describe its properties as a guide to its most effective application; and when the new material may be produced in compositions having a series of graded properties, tests to select the combination of properties best adapted for various uses are helpful. The class of materials to be considered in this paper are hard tool materials produced by processes of powder metallurgy from hard carbide constituents and various matrices of iron, nickel or cobalt, or alloys of them with tungsten, or tungsten and carbon. The customary use of carbide hard alloys is for metal-cutting tools; although wire-drawing dies, lathe centers, follow rests, grinding rests, burnishers, rolls, extrusion dies, measuring gauges and micrometers, and a number of other tools are also made with these hard alloys as the essential wear-resisting parts. The properties and tests to be considered are those affecting these uses. In the development of tool materials since the industrial revolution we have had carbon tool steels, Mushet steel, high-speed steels, stellites, and now cemented carbide compositions. For an understanding of the latter category of materials their properties and uses relative to the older and more familiar tool materials will be considered. Hardness has been the property of greatest practical interest in tool materials. The word "hardness" is a generalized term lacking definite¬ness unless the specific test used is described. However, efforts to explain physical properties as a consequence of chemical bond, and distance between atoms in chemical compounds have been illuminating. This seems the most generalized attack on the problem, and is based upon the idea that atoms in a lattice are held together as the square of the valence and inversely as the square of the distance between the atoms. The compounds compared must all be of the same crystalline arrangement. It is interesting to note the values of the figure [V ] a number of

Jan 1, 1938

By I. R. Kramer

A delay time for yielding in cold-worked face-centered-cubic metals was found. Slip on (123) planes was observed. Glide on these planes occurred during the delay-time period before slip starts on the (111) planes. AN important approach to the study of the anchoring and blocking of dislocations is available through the delayed-yield phenomenon which has been observed in body-centered and hexagonal close-packed metal by several investigators. Clark and his associate1-5 showed that a delay time for yielding is present in mild steels and fine-grain molybdenum. Type 302 stainless, SAE 4130 normalized, SAE 4130 quenched and tempered, and 24s-T aluminum aid not have a delay time. Kramer and Maddin6 studied the delay-yield effect. in metal single crystals. While they found a delay time in body-centered-cubic metals none could be found in the face-centered-cubic metals. Later7 a delay time was found in hexagonal close-packed metals. cottrell8 has proposed an explanation for the difference in the yield phenomena of b.c.c. and f.c.c. metals based upon the anchoring of edge dislocations by the proper types of impurity atoms (C and N). In the body-centered-cubic lattice the interstitial atoms are near a cube edge and can interact with an edge dislocation, while in a face-centered-cubic lattice the distortion around an interstitial atom is of spherical symmetry and cannot anchor a screw dislocation which has practically no hydrostatic component. Cottrell's theory seems to account rather well for the behavior of body-centered-cubic . metals. EXPERIMENTAL PROCEDURE The apparatus used in these experiments is essentially of the same design as described previously.' Single crystals 1 in. long and having a diameter of % in. were placed in a pendulum which consisted of a bar 8 ft long designed with a crystal holder to accommodate the specimen at low temperatures. This portion of the apparatus was supported on fine molybdenum wires. A bar of the same diameter and length comprised the other portion of the apparatus. This bar was supported on a set of roller bearings arranged around the periphery of the bar to allow accurate alignment. This bar was propelled by means of a spring-loaded gun and allowed to strike the lead bar in front of the single-crystal specimen. SR-4 type A-8 resistance strain gages were cemented to the specimen and the strain measurements were obtained by amplifying the strain-gage output by means of a high-gain preamplifier. A tektronix 545 oscilloscope was used together with a polaroid camera to record the strain and time sweep. An Ellis Associate Bridge was used to calibrate the strain gages and calibration readings were obtained before each test. The sweep of the time signal was initiated by means of a miniature thyraton which was fired when the two bars came into contact. The single-crystal specimens were cut from single-crystal bars about 12 in. long, grown by a modified Bridgman technique. The aluminum crystals were made with material of 99.99 pct purity while the purity of the copper was 99.999 pct. A cut-off wheel was used to prepare the specimens which were then machined to the desired length. The two opposite faces of the specimen were parallel to each other and perpendicular to the axis of the specimen. The specimens were compressed 1 pct. No machining followed thereafter. In some cases prestraining was carried out in liquid nitrogen by impacting the specimens directly in the apparatus so that subsequent observations could be made without allowing the specimen to warm up to room temperature. The single crystals were compressed 1 pct at room temperature in a hand press without much control of the rate of deformation. In some cases specimens were recompressed to obtain the desired length change. As far as could be determined in these experiments this factor did not seem to influence the results. The SR-4 strain gages were glued with a cellulose type cement onto the specimen surface and baked at 45°C for 12 hr. As a check on the baking treatment gages were allowed to dry at room temperature. All delay time tests in this paper were conducted in a liquid nitrogen bath at -195°C. A schematic delay time oscilloscope trace is shown in Fig. 1. At point B the elastic stress wave caused by the impact reaches the strain gage on the specimen. The portion BC is the elastic strain. In this investigation the strain at point C was used to calculate the critical resolved shear stress by multiplying by the proper modulus depending upon the orientation of the single-crystal specimen. The time between C and D is the delay time portion of the curve. This portion of the curve is fairly flat but does have a definite microstrain associated with it. After the point D is reached the specimen deforms rapidly and the strain reaches a maximum at E. Following this, depending upon the length of the bar behind the specimen, the strain remains constant for a period and then decreases when the reflected elastic wave returns from the end of the pendulum bar. A permanent plastic strain is recorded on the oscilloscope trace and also measured by a strain-measuring bridge. The strain, E p,

Jan 1, 1960

By John J. Secretary Egan

The present list of problems relating to the physical chemistry of steelmaking has been prepared by the Committee on the Physical Chemistry of Steelmaking, from answers to a questionnaire submitted to a number of metallurgists engaged in both industrial and educational work throughout the United States. The purpose of the project is to make available to research laboratories a list of problems, all reduced to their simplest terms, the solution of which would aid in creating a better understanding of the steelmaking process. It is not intended to restrict the problems to practical steelmaking. The list also includes the study of the properties, and their correlation, as well as the physical and chemical reactions, of all substances that occur or that may be in any way associated with steelmaking operations, such as metallic substances, refractories, nonmetallic inclusions, and the constituents of slags. Many of the problems can be carried out in university or other research laboratories. Others may be most successfully attacked by cooperation of the research men with the operating personnel. It is the Committee's earnest wish that this cooperation be fostered. It is requested that investigators who are working on any of the problems listed and who anticipate future publication of their results, notify the Secretary of the Committee that such investigation is in progress. Suggested additions to the present list are also requested. The Committee is undertaking to act as a clearing house for information regarding the topics in this field that are being actually studied. Interested persons are invited to correspond with the Secretary. I. Data involved in the state of equilibrium for the various systems (laboratory work, almost entirely). A. Specific heats, heats of formation, entropies and free energies of various PURE ELEMENTS OR COMPOUNDS; ALSO CERTAIN TYPICAL SLAGS AND REFRACTORIES I. Determination of specific heats and entropies of oxides, sulphides, nitrides, etc, over a wide temperature range. 2. Determination of free energies of oxides, sulphides, nitrides, etc., over a wide temperature range. 3. Determination of the heats of formation of the oxides, sulphides, nitrides, etc. 4. Determination of the thermodynamic properties of the more important mineral-ogical constituents of the basic open-hearth slags such as calcium silicates, calcium phosphates, calcium ferrites, manganese silicates, FeO and Fe2O3. 5. Determination of the specific heats of open-hearth slags, including liquid silicates, if possible.

Jan 1, 1941

By John J. Secretary Egan

The present list of problems relating to the physical chemistry of steelmaking has been prepared by the Committee on the Physical Chemistry of Steelmaking, from answers to a questionnaire submitted to a number of metallurgists engaged in both industrial and educational work throughout the United States. The purpose of the project is to make available to research laboratories a list of problems, all reduced to their simplest terms, the solution of which would aid in creating a better understanding of the steelmaking process. It is not intended to restrict the problems to practical steelmaking. The list also includes the study of the properties, and their correlation, as well as the physical and chemical reactions, of all substances that occur or that may be in any way associated with steelmaking operations, such as metallic substances, refractories, nonmetallic inclusions, and the constituents of slags. Many of the problems can be carried out in university or other research laboratories. Others may be most successfully attacked by cooperation of the research men with the operating personnel. It is the Committee's earnest wish that this cooperation be fostered. It is requested that investigators who are working on any of the problems listed and who anticipate future publication of their results, notify the Secretary of the Committee that such investigation is in progress. Suggested additions to the present list are also requested. The Committee is undertaking to act as a clearing house for information regarding the topics in this field that are being actually studied. Interested persons are invited to correspond with the Secretary. I. Data involved in the state of equilibrium for the various systems (laboratory work, almost entirely). A. Specific heats, heats of formation, entropies and free energies of various PURE ELEMENTS OR COMPOUNDS; ALSO CERTAIN TYPICAL SLAGS AND REFRACTORIES I. Determination of specific heats and entropies of oxides, sulphides, nitrides, etc, over a wide temperature range. 2. Determination of free energies of oxides, sulphides, nitrides, etc., over a wide temperature range. 3. Determination of the heats of formation of the oxides, sulphides, nitrides, etc. 4. Determination of the thermodynamic properties of the more important mineral-ogical constituents of the basic open-hearth slags such as calcium silicates, calcium phosphates, calcium ferrites, manganese silicates, FeO and Fe2O3. 5. Determination of the specific heats of open-hearth slags, including liquid silicates, if possible.

Jan 1, 1941

By N. S. Stoloff, M. Gensamer

The effects of temperature, grain size, and magnesium content on the strength and ductility of cadmium were studied in the range -269° to 23 °C. A sharp drop in ductility between -140° and -190°C marked a transition in fracture mode from ductile shear to inter gvanular fracture. The addition of up to 15.35 wt pct Mg in solid solution raised the transition temperature, and for two compositions produced basal cleavages. The relatively high ductility of unalloyed cadmium at cryogenic temperatures is attributed to temperature independence of the yield stress and the absence of dislocation locking. ALTHOUGH numerous studies have been made of the mechanical properties of cadmium single crystals,1-5 no comprehensive investigation of deformation and fracture in polycrystalline cadmium has been carried out. This investigation was initiated to determine the mechanisms of deformation and fracture in polycrystalline cadmium, and to attempt to correlate these mechanisms with the behavior of other metals of hexagonal close-packed structure. A second objective of this work was to determine whether the slip systems and mode of fracture of polycrystalline cadmium could be altered by reduction of the axial ratio, which is 1.886, through alloying. Dorn and co-workers' have been able to induce prismatic slip in magnesium through alloying to reduce the axial ratio. Single crystals of cadmium are so highly ductile that glide strains of 400 pct are observed at room temperature, and 80 pct at -269°c.l Failure in every reported case is by necking down and shearing off of the crystal. Cleavage in cadmium single crystals has never been observed. Magnusson and aldwin reported a ductile to brittle transition for polycrystalline cadmium at about —160 C for specimens tested at a strain rate of 0.05 in. per in. per min in tension. However, even at -196° substantial ductility was retained. The transition temperature was strain rate dependent, impact loading at 19,000 in. per in. per min raising the transition temperature to about -85°C while leaving the low temperature ductility unchanged. No information was given on microstructures or fracture mode, nor were stress-strain characteristics reported. In the present investigation, tensile tests were carried out on polycrystalline cadmium and solid solution Cd-Mg alloys to determine flow stresses, work-hardening behavior, fracture strength, and fracture ductility. Variables employed included temperature, alloy content (and c/a ratio), and grain size.Some compression data also have been obtained for comparison purposes. I) EXPERIMENTAL PROCEDURES A) Polycrystalline Cadmium. Two purities of cadmium were employed in this investigation. Cadmium of 99.95 pct purity was supplied by Belmont Smelting and Refining Co. Cadmium of 99.99+ pct purity was supplied by American Smelting and Refining Co. Threaded cylindrical tensile specimens were machined to give approximately a 1/2 in. long straight gage section with a reduced diameter of about 0.110 in. Specimens were heat treated in evacuated pyrex capsules in the range 140" to 290°C to produce desired grain sizes. All specimens were polished in a solution containing 320 g Cr03 and 20 g NaS04 in 1000 cc of H20. Occasionally this solution caused staining of the specimen, in which case a further polish with a solution of one part HN03 and two parts H202 in two parts ethyl alcohol was employed.' Tensile testing was carried out on a screw-driven Instron machine, at a constant rate of crosshead movement, which for most tests was 0.01 in. per in. per min. Load vs time, and therefore load vs total strain, were recorded. Temperatures from -196" to -40°C were obtained by passing nitrogen gas through a copper coil immersed in liquid nitrogen, and then feeding the gas into a jacket around the specimen. Tests at -269°C were carried out in a helium cryostat, at a crosshead rate of 0.1 in. per in. per min, with specimens of 1 in. gage length. Compression specimens were tested in a jig similar to one designed by ilman. The jig was mounted on the under side of the Instron crosshead. Load was transmitted by means of a rod connected to a movable part of the jig at one end, and the load cell at the other end. A downward movement of the crosshead applied a compressive load to the specimen.

Jan 1, 1963

By Daniel R. Shawe

Large tabular beryllium deposits in waterlaid rhyolitic tuff at Spor Mountain, Utah, contain the world's largest known resources of beryllium (as bertrandite). The district also has produced fluorspar and uranium. The largest beryllium deposit is about 2.5 miles long, and known deposits contain many million tons of material with at least 0.5 per cent BeO. The beryllium-bearing tuff (Pliocene?) underlies topaz-bearing rhyolite ( Pliocene?) that contains unusually high amounts of beryllium, fluorine, and uranium, and overlies other volcanic rocks (Pliocene? or Micocene?) and marine carbonate and elastic rocks ( Paleozoic). The deposits occur in hydrothermally altered tuff only where it contains abundant carbonate pebbles eroded from the Paleozoic rocks and where the tuff was deposited as thick layers in now-buried paleovalleys. Basin and Range faults, thrust fa ults, and possibly strike-slip faults formed in this part of the Basin and Range province during the late Tertiary, and volcanic rocks were extruded. Beryllium mineralization probably occurred during this episode. Undoubtedly the beryllium deposits are related genetically to the topaz-bearing rhyolite, but the details of their genesis are not certain and probably are complex. Beryllium deposits are close to major faults, and locally the beryllium is concentrated at faults, indicating fault control of mineralization. Some elements in the deposits, such as lithium, however, are evenly distributed in certain Luff beds and perhaps were introduced prior to faulting. Still other elements, such as manganese and lead, were concentrated in the beryllium deposits and subsequently were leached along late fractures, indicating a period of metal redistribution following mineralization.

Jan 1, 1968

By Milton E. Wadsworth, John N. Ong, W. Martin Fassell

The temperature and oxygen concentration dependence on the reaction of sphalerite in oxygen at pressures from 6 to 640 mm Hg have been investigated in the temperature range 700° to 870°C. Sphalerite has been found to oxidize linearly over this entire temperature and pressure range. At higher rates, considerable self-heating was observed. The dependence of the oxidation rate on the oxygen concentration may be expressed by: Rate = k' where k' is the specific rate constant and 0 = K1[O2]/(1 + KI[O2]), where K1 is the equilibrium rate constant for the adsorption of oxygen on sphalerite. Values of the activation energy and the enthalpy of adsorption were found to be 60.3 and —59.6 kcal per mol, respectively. Data have been presented that indicate conditions under which either a sulphatizing or an oxidizing roast may be obtained. ROASTING processes have been employed in the metallurgy of a great number of basic metals in use today. Until recently, however, little attempt has been made to deduce the fundamental mechanism by which oxidation takes place. Structural changes upon oxidation have been investigated1 = and thorough work has been performed with regard to the reaction products and the thermodynamics of the oxidation reactions. The objective of this investigation was to determine the rate of oxidation of sphalerite and to apply the absolute reaction rate theory in the theoretilcal interpretation of the experimental results." "O Description of Apparatus The apparatus contains the following features: 1—a furnace with gas system, 2—an autographic weighing system, and 3—a temperature control system. Furnace With Gas System—The furnace was mounted by a yoke on each end and was free to travel up and down on steel guide rods, permitting the introduction and removal of samples from the apparatus with minimum difficulty. The furnace was heated by three sections of Kanthal wire wound externally on a zirconia tube and insulated with Fiber-frax. Pure gases or mixtures of gases were introduced into the lower end of the furnace through two flowmeters, a mixing chamber, and a gas-tight sparger, Fig. 1. The gaseous products of the reaction and the unused gases were prevented from escaping to the atmosphere by maintaining a small negative pressure on the system. This procedure permitted air from the outside to enter through the small an-nulus around the quartz suspension fiber and prevented the escape of the internal gases. Autographic Weighing System—The autographic weighing system consisted of an adapted gold balance, a photoelectric circuit, and a weight recorder, Fig. 2. The sample was suspended from one end of the balance beam by means of a platinum chain outside the furnace and a long thin quartz fiber on the inside of the furnace. On the other end of the balance beam, the necessary weights were added to counterbalance the sample. In addition, a calibrated chain was added to the balance which was linked directly to the weight recording unit. Control was effected by means of a photoelectric circuit." A parallel beam of light from a strong source was directed onto a small front-surfaced aluminum mirror mounted in the middle of the balance beam and then to a front-surfaced mirror mounted on the ceiling of the room. The beam was then reflected onto a front-surfaced right prism at a distance of 9 ft from the balance

Jan 1, 1957

By Kenneth B. Ray, George R. Gardner

The application of wet cleaning processes for the beneficiation of bituminous coal has created in some localities a problem in the recovery and disposal of fine solids in the washery water. The maximum allowable concentration of these solids in the washery circuit that is consistent with satisfactory operation of the cleaning units remains a controversial point. It has, however, been generally recognized for a number of years that some degree of control should be exerted over the concentration of such material. Early methods of control involved intermittent or continuous discharge of a portion of the plant slurry into near-by streams or settling ponds, and this persisted even after the adoption of settling tanks or cones. The practice is not always economical, for two reasons: first, because of the waste of coal, and, second, because it is sometimes difficult and expensive to obtain an adequate supply of water. The latter condition often is aggravated by chemical treatment of the make-up water that is necessary to prevent excessive corrosion of plant equipment. The modern approach to this problem has been the adoption of continuous thickening devices. However, because such equipment occupies considerable plant space and is somewhat expensive to construct, the practice of loading these thickeners beyond their rated capacity is widespread, therefore often the performance of such units is not altogether satisfactory. In recent years, European washeries have increased the rate of settling of the fine coal from the slurry by the addition of specially prepared starch solutions. These reagents cause flocculation of the solid particles and thereby increase the rate of sedimentation. The first important work on the flocculation and clarification of coal slurry was done by Henry, who developed the Henry process and used it successfully in Belgian preparation plants. Soon after the initiation in Belgium, the process was introduced into England, where subsequent investigation developed similar processes, which were successfully used in

Jan 1, 1940

By George R. Gardner, Kenneth B. Ray

The application of wet cleaning processes for the beneficiation of bituminous coal has created in some localities a problem in the recovery and disposal of fine solids in the washery water. The maximum allowable concentration of these solids in the washery circuit that is consistent with satisfactory operation of the cleaning units remains a controversial point. It has, however, been generally recognized for a number of years that some degree of control should be exerted over the concentration of such material. Early methods of control involved intermittent or continuous discharge of a portion of the plant slurry into near-by streams or settling ponds, and this persisted even after the adoption of settling tanks or cones. The practice is not always economical, for two reasons: first, because of the waste of coal, and, second, because it is sometimes difficult and expensive to obtain an adequate supply of water. The latter condition often is aggravated by chemical treatment of the make-up water that is necessary to prevent excessive corrosion of plant equipment. The modern approach to this problem has been the adoption of continuous thickening devices. However, because such equipment occupies considerable plant space and is somewhat expensive to construct, the practice of loading these thickeners beyond their rated capacity is widespread, therefore often the performance of such units is not altogether satisfactory. In recent years, European washeries have increased the rate of settling of the fine coal from the slurry by the addition of specially prepared starch solutions. These reagents cause flocculation of the solid particles and thereby increase the rate of sedimentation. The first important work on the flocculation and clarification of coal slurry was done by Henry, who developed the Henry process and used it successfully in Belgian preparation plants. Soon after the initiation in Belgium, the process was introduced into England, where subsequent investigation developed similar processes, which were successfully used in

Jan 1, 1940

By Frank R. Van Horn

It is customary to ascribe two general modes of occurrence to natural gas, namely, shale gas which, as the name indicates, is found in shale, and reservoir gas, which occurs in sandstone, conglomerate and dolomitic limestone. Both of these types are found in the Cleveland district. The shale gas has been produced on a small scale for a long period of years, probably dating back as far as 1883. Shale gas is a low-pressure gas, small in volume with variable pressure, and is limited to no definite horizon. It is generally independent of oil, may last for a long time, and is not dependent to any great extent on the structure of the rocks. There are many such wells in the district which range from 400 to 1,840 ft. in depth, although most have been completed at about 800 ft. This indicates that the wells pass through the Cleveland and Chagrin shales into the Huron or Portage shale of the Upper Devonian. During the last 2 years great interest has developed in a deeper-seated reservoir gas. What is commonly called reservoir gas is generally a high-pressure gas occurring in large volume at a definite horizon. Oil may, or may not, be associated with the gas, and in most regions in which reservoir gas is found, the geological structure is of great importance. This type of gas occurs in all large fields such as those of West Virginia which have been supplying Cleveland until the recent discovery of local gas at great depths in commercial amounts. Historical Outline The oldest well producing reservoir gas in the district was drilled in 1886 in Newburg for what was then known as the Cleveland Rolling Mill Co. This well was 3,000 ft. deep, and was thought to have reached the "Clinton" formation. Two "sands" showing small amounts of oil were recorded in the Niagara limestone at depths of 2,658 and 2,686 ft. This is about the horizon of the so-called Newburg sand which has proved to be of some importance as a source of gas and oil by recent drilling operations. The rock pressure was reported to be 400 to 500 lb. per square inch, but since the volume was only 14,000 to 16,000 cu. ft. daily, the well was not only considered unsuccessful but was thought to prove the absence of high-pressure gas in commercial quantities in the Cleveland district.

Jan 1, 1917

By Russell W. Dayton

The metallurgical polarization microscope has been utilized in several researches in the last few years, thus attaining a fair degree of prominence, but little has been written in a manner suitable to a metallurgist concerning the theory of this instrument. In this investigation the theory was carefully studied, and the results are presented here in a detailed manner, yet as simply as possible. The theory is discussed with particular reference to the three chief functions of the instrument: (1) determination of anisotropy; (2) effect of strain; and (3) identification of inclusions. Each of these is investigated experimentally, with especial attention to the mechanism of producing any effect. Where possible, the discussion is supplemented by photomicrographs. The instrument used had numerous defects as a polarization microscope; these and their remedies are discussed. In the microscopic study of transparent mineral sections (chalcography) the use of polarized light has aided tremendously in the identification of a mineral. The determination of strain in transparent substances (photoelasticity) by the use of polarized light has lately become a commercial process, used in testing finished glass articles. The success of the use of polarized light with opaque materials has not been so great. The magnitude of the effects obtained is much less than that of the corresponding effects with transparent materials, and the mechanical difficulties are much greater. Königsberger,"' i in 1909, was the first to apply polarized light to the microscopic study of opaque substances; Endell and Hanemann(2) were the next, in 1913. In 1919 and 1920, Wright(3,4) prepared two papers on the subject. In the first he developed the detailed mathematical theory from the viewpoint of the electromagnetic theory of light, and in the second described the various methods in use, giving improvements of his own. Schwarz(5)

Jan 1, 1935

By Russell W. Dayton

The metallurgical polarization microscope has been utilized in several researches in the last few years, thus attaining a fair degree of prominence, but little has been written in a manner suitable to a metallurgist concerning the theory of this instrument. In this investigation the theory was carefully studied, and the results are presented here in a detailed manner, yet as simply as possible. The theory is discussed with particular reference to the three chief functions of the instrument: (1) determination of anisotropy; (2) effect of strain; and (3) identification of inclusions. Each of these is investigated experimentally, with especial attention to the mechanism of producing any effect. Where possible, the discussion is supplemented by photomicrographs. The instrument used had numerous defects as a polarization microscope; these and their remedies are discussed. In the microscopic study of transparent mineral sections (chalcography) the use of polarized light has aided tremendously in the identification of a mineral. The determination of strain in transparent substances (photoelasticity) by the use of polarized light has lately become a commercial process, used in testing finished glass articles. The success of the use of polarized light with opaque materials has not been so great. The magnitude of the effects obtained is much less than that of the corresponding effects with transparent materials, and the mechanical difficulties are much greater. Königsberger,"' i in 1909, was the first to apply polarized light to the microscopic study of opaque substances; Endell and Hanemann(2) were the next, in 1913. In 1919 and 1920, Wright(3,4) prepared two papers on the subject. In the first he developed the detailed mathematical theory from the viewpoint of the electromagnetic theory of light, and in the second described the various methods in use, giving improvements of his own. Schwarz(5)

Jan 1, 1935