Search Documents

By J. N. Van der Merwe

"A major shortcoming of the statistical back-analysis of coal pillar strength is that it relies on the asmined pillar dimensions, not taking into account time-related pillar scaling with subsequent reduction in pillar width. The paper describes an investigation where the rate of pillar scaling was applied to the pillars in the databases of failed and unfailed pillars. The reduced pillar sizes were then used in the same method of statistical back-analysis that had been used in the past.This resulted in an equation for pillar strength which predicts significantly greater pillar strength than the previous statistical analyses, which is similar to the strength which had been found earlier by direct testing of large specimens underground. It is concluded that the lower strengths found by previous statistical analyses are due to the incorrect pillar width being used and that by adjusting the pillar sizes to compensate for scaling, more credible results that correspond to direct testing are obtained.As the newly derived strength equation is time-dependent, it follows that the safety factors and probabilities of failure are likewise time-dependant. An equation to determine the probability of failure is also developed. This results in the safety factor being close to unity at a probability of failure of 50%, which is aligned to statistical expectation. IntroductionSince the Coalbrook mine disaster, caused by massive pillar collapse, there have been several attempts at analysing and defining the strength of coal pillars. It was realized in the very beginning that performing classical strength tests on coal specimens in a laboratory and then transferring those results to real coal pillars could not be successful. The scatter of results is one problem and, more seriously, there is a size effect (at least for small specimens) that made the transformation of strength results to much larger coal pillars underground all but impossible.Two main schools of thought then emerged. Some researchers preferred to perform direct strength tests on large specimens underground, while others relied on statistical back-analysis of failed and unfailed pillar cases, attempting to determine the differences in size and shape that would allow a satisfactory prediction of failure. The latter school of thought resulted in the method that was widely accepted by the South African coal mining industry, described in the landmark publication by Salamon and Munro (1967)."

Jul 1, 2019

By Matthew J. Sheridan

The Bureau of Mines study described in this report was conducted in the Denver, Colo., area (1) to summarize existing conservation practices as related to the most beneficial utilization of deposits of sand and gravel; (2) to identify the conflicting positions of the aggregate producer, the mineral owner, nearby residents, and local government officials responsible for determining land status and for issuing operating permits; and (3) to show the need for planning in Denver and in other expanding communities toward obtaining the benefits of conservation of our rapidly dwindling mineral resources. In order to determine the effects of urbanization on the Denver aggregate industry, interviews were held with owners of sand and gravel operations, with producers of concrete and bituminous pavement, with city and county planning and zoning personnel, and with representatives of various interested organizations. The conservation and ultimate utilization of deposits of construction raw materials near expanding urban areas can best be accomplished by long-range land-use projection and the requesite cooperation of technically advised planning and zoning administrators, government officials, mineral producers, and land developers.

Jan 1, 1967

By Yan Yuan

Stable Nitroxyl polymers, such as poly (2,2,6,6-tetramenthyl-1-piperidinyloxy-4-yl methacrylate) (PTMA), are known to be effective as cathode active materials for lithium rechargeable betteries.The nitroxide radicals displayed a reversible and very rapid redox performances.We present a new synthesized method to get PTMA powder, then a doctor-blading method was used to prepare the PTMA composite electrodes, enabling successful production of homogeneous electrodes. It was characterized through FT-IR and SEM methods.The organic radical battery consists of lithium metal anode and PTMA cathode with an active material content of 65wt%.The best performance is achieved with a thin cathode that shows nearly 100% utilization of the active material (111mAh/g) at 0.1C.Through the electrochemical tests, it was found that there was a stable plateau at 3.5V while discharging. Besides, the cycling stability and rate capability were measured in detail. Although they showed a certain quantity of irreversible capacity on the first cycle, the capacity stabilized after the second cycle.

Jan 1, 2009

By Larry S. Diaz

The paper considers the selection of control instrumentation for a modern flotation plant, as well as the best interpretation and most effective use of the process data obtained. Process control computer availability is considered from the outset. A general philosophy of control is proposed which leads toward a system that is its own reliability monitor. The bulk of the problems are in grinding and classification. Alternative control methods are described that use particle size measuring devices. Flotation controls, based to a large extent upon on-stream X-ray analysis, are reviewed in detail. Reagent control methods are also examined. Methods to analyze the data obtained from the various measurement devices are introduced. These methods would enable an estimate of the validity of the data and require some redundant information. Another objective of these methods is the protection of operating equipment from possible control malfunctions. Although the discussion generally considers some degree of computer usage, this paper attempts to describe instrumentation and data analysis methods that enable control with or without the process control computer.

Jan 1, 1972

By G. S. Beaumont

This report presents a programme of work to demonstrate the use of a surface-based centralised computer control system for the remote monitoring and control of underground conveyors in a US coal mine. The system selected for demonstration was the 'Dynalink' Micro MINOS system which is manufactured by Hawker Siddeley Dynamics Engineering Limited. The site selected was Barnes S Tucker Lancashire No. 20 Mine located near Carrolltown, Cambria County, Pennsylvania. The system concept, operating and application software was designed and developed by the. British National Coal Board. The report describes the selection of the site, specification of the system requirements, commissioning, operation and evaluation of the system under typical US mine operating conditions. Experience with the system, based primarily on the system reliability and performance of conveyor control, was favourable. Mine management personnel felt that the system had successfully achieved its objectives and were keen to expand monitoring and control to other activities.

Jan 1, 1986

By Dean H. Ambrose

[Mining and processing earth's materials form the basic building blocks from which many technology advancements and products are made. Virtually all metallic and non- metallic products are derived from a substance found in our earth that we blend, mold, extrude, or pulverize into something useful, the mining industry is responsible for the first step of this process: extraction from the ground. Mining particularly coal mining. poses significant risks to both humans and machines. As raw materials are]

Jan 1, 2009

By D N. B Skinner, M P. Simpson

At Ohio Creek, 3 km northwest of the Thames bonanza goldfield, porphyry Cu-Au mineralisation is hosted in a dacite porphyry associated with porphyry intrusion breccias and overlying andesites and dacites. The geological setting is a Jurassic greywacke basement overlain by Late Miocene andesite-dacite volcanics which are extensively altered to propylitic and argillic assemblages. Diamond drilling at Ohio Creek in 1978-1981 by Amoco Minerals intersected low grade Cu-Au (0.12-0.20% C~ 0.23-0.4 glt Au) mineralisation An advanced argillic 'alteration cap containing quartz-alunite¦dickite or pyrophyllite-dickite¦diaspore is centred on the adjacent Lookout Rocks and has potential for high sulfidation Au-Cu mineralisation. There is a zonation from potassic K-feldspar-magnetitealteration at depth in the dacite porphyry, through an overlying phyllic quartzsericite- pyrite zone which is overprinted by pyrophyllite in the overlying advanced argillic cap. Early quartz stockwork veinlets associated with the potassic alteration contain fluid inclusions that trapped a highly saline (50-80 wt% NaCI equiv) fluid at high temperatures (450 to >600¦C) indicative of a magmatic fluid. Some chalcopyrite is associated with slightly later quartz-magnetite veinlets, but the bulk of the copper occurs as disseminated chalcopyrite associated with the phyllic alteration. The potassic alteration is surrounded and overprinted by propylitic chlorite¦epidote alteration. Late polymetallic sulfide-quartz-anhydrite veins occur within and around the margins of the porphyry system as in the Kaiser Reef. Fluid inclusions associated with these late veins were formed at temperatures of about 250-320¦C from low salinity (1-3 wfl~ NaCI equiv) fluids. The spatial association between porphyry eu-Au mineralisation, advanced argillic alteration and polymetallic sulfide veins suggests that they are genetically part of the same hydrothennal system. This is consistent with reconnaissanceK-Ar dates of 11.6-10.7 Ma for the intrusive porphyry at Ohio Creek, alunite in the advanced argillic alteration zone at Lookout Rocks and sericite selvedges from the Waiotahi gold-quartz veins at Thames.

Jan 1, 1998

By AIME AIME

HOWARD H. PRESTON, professor of economics and business at the University of Washington, presented a paper before the North Pacific Section, A.I.M.E., on Jan. 23, on the "Economic Aspects of Gold and Silver." He carefully reviewed recent governmental actions that have affected those metals and gave an interpretation of their effects. A brief excerpt from his address; follows: Including the proclamation of March 6, 1933, the principal steps of the present Administration which have carried the United States off the gold standard and led up to the present program have been: (1) The Presidential proclamation of March 6 controlling gold. (2) The monetary sections of the Emergency Banking Act of March 9. (3) Mobilization of gold under Executive orders issued March 10 and April 5. (4) The gold embargo by Executive order, April 20. (5) The controlled inflation bill, May 12. (6) The joint resolution abrogating the gold clauses, June 5. (7) The Executive orders on newly mined gold, Aug. 28. (8) The President's radio address of Oct. 22 and the R.F.C. gold-buying program. (9) New anti-hoarding order calling in small holdings of gold, Dec. 28, 1933 and Jan. 15, 1934. (10) Nationalization and revaluation of gold' (Message to Congress, Jan. 15).

Jan 1, 1934

By K Morrison

Australia’s ageing population means that by 2050 there will be 2.7 people of working age to support each Australian aged 65 years and over compared with five working people per retiree today and compared with 7.5 in 1970 (Swan, 2010). This means that there is going to be a greater demand on social services – for medical and aged care – from a smaller private income base. How will this gap be met? Australia is fortunate in that it has vast resources of mineral wealth; from iron ore, nickel and gas in Western Australia to the giant copper and uranium deposits at Olympic Dam in South Australia.The prospect of a meaningful profit based tax on this vast mineral wealth has been lost through Australian government’s handling of the issue in 2010 and with an industry fiercely opposed to the prospect of a mining tax. Hence, new ways of thinking are required. This paper looks at the issues facing the implementation of a novel scheme whereby Australia leases the mineral resources it extracts and thus derives income over the decades the metals are in-use in pipes, wires and structures with a premium paid for unreturned material or that used in dissipative applications. Applicable minerals could include copper, aluminium, nickel and rare earths. If Australia simply digs up and sells the metals once, the buyer becomes custodian of that resource and they benefit from controlling the future ‘above-ground’ resource stock.A complementary driver for a leasing scheme is the increasing importance of chain-of-custody following initiatives of the Responsible Jewellery Council with gold and diamonds, now with the potential to extend across commodities. The Australian minerals sector could thus position itself as a premium supplier with high social and environmental credentials.Recognising the implementation challenges, this paper includes a review of how such a system could be enforced to ensure that the metal is tracked throughout its life. It concludes with a discussion of the rates and terms should such agreements hold and suggestions for institutional arrangements for enforcing compliance.

Nov 22, 2011

By F. A. Rutledge, J. J. Mulligan, W. H. Kems, R. L. Thome

"As a part of the United States Department of the Interior program for the development and use of Alaska raw materials, the Bureau of Mines is conducting an investigation of deposits f nonmetallic minerals accessible to the Alaska Railroad for use in building materials in the Alaska Railroad-belt area. The results of the investigations, to date, indicate that raw materials for the production of brick products are in plentiful supply as clay in the Anchorage area, as fire clay at Sheep Mountain, and as shale in the Healy Creek coal formations near Healy, Alaska.Shale for the production of lightweight aggregate or Haydite occurs near mile 67 on the Glenn Highway, and preliminary tests give excellent results. Physical tests are new in progress on commercial-size concrete building units made with this aggregate. Another shale deposit in the same formation was located at mile 16 on the Matanuska Branch of the Alaska Railroad, and preliminary tests give comparable results.Natural lightweight aggregate in tree form of pumice and pumicite occurs in Katmai National Monument and has been used with excellent results in lightweight-building units in Anchorage and Fairbanks. These deposits will be investigated in more detail by the Bureau of Mines during 1952.One small perlite deposit near Healy, Alaska, showed excellent expanding properties, and the product compares favorably with commercial perlites being used in the States for plaster and concrete aggregates. Additional investigation by the Bureau of Mines to delimit the known occurrence and, if possible, discover others were planned for the 1951 field season.The pumice from Katmai National Monument also was considered for use as a pozzolan in pozzolan-portland concrete. Tests by the Bureau of Reclamation indicate that the pumice sample submitted by the Bureau of Mines would be satisfactory in strength development but is not outstanding. Natural activity is good and is greatly improved by calcination at 1,4000 F. Water requirements and shrinkage also are satisfactory. However, the material is ineffective in reducing expansion owing to alkali-aggregate reaction; and, if reactive aggregate is used to make concrete, it would not insure against excessive expansion. An attempt will, be made during the 1952 field season to delimit pumicite deposits along the Alaska Peninsula more amenable for use in pozzolan-portIand concrete.Because the Railroad belt has such a rigorous climate, insulation for new construction is of prime importance. Luring the Bureau of Mines, investigation of building materials all samples were submitted for chemical analyses as possible sources of raw materials for the production of rock wool, one of the best insulation mediums. Four areas having deposits of the required constitu¬ents were located as follows: Anchorage area, with Potter limestone and argillite; Cantwell-Windy area, with limestone and shale; West Fork of the Chulitna River area, with limestone and agrillite; and Homer-Seldoyla area, with Seldovia limestone and Homer clay. It was planned to take bulk samples of these formations and submit them for testing during the 1951 field season."

Mar 1, 1953

By A. Roberts

This paper reviews progress in equipment design and in the techniques applied to mine lighting in Great Britain. The incidence of the disease miner's nystagmus, which was a major source of concern only a few years ago, has now diminished, largely owing to improvements in standards of lighting in mines. The reorganisation of the coal mining industry, involving increasing mech-anisation, together with new safety legislation, has brought about the widespread use of mains electric lighting underground. An account is given of some of the results of research to determine the lighting conditions needed for compliance with the compulsory legal requirement of "sufficient and suitable" general lighting at specific localities in British mines. Some details are given of the techniques applied and the results of recent research in the problem of glare from miners' cap lamps. Of the various factors in the working environment of the miner, it is true to say that lighting is seldom given attention comparable with that devoted to other factors, such as dust, heat and humidity, or atmospheric gas content. No doubt one reason for this lies in the ability of the human eye to adapt itself to low brightness levels. Be that as it may, the fact is that at the turn of the 20th century the miner's working light improved little throughout the centuries during which mining technology has developed. Indeed, in coal mines which encounter a methane explosion hazard, flame safety lamps, with a luminous intensity less than one candle power, were virtually the sole means of lighting during almost the whole of the 19th century. The 20th century has witnessed a substantial improvement in lighting techniques underground in coal and metalliferous mining. In Great Britain the general pattern has been one of standards periodically raised by the implementation of Statutory Regulations imposed under successive hlines Acts, but it is fair to add that the more progressive mining companies usually anticipated the Statutory Regulations, which when they have been put into effect have served to turn into general practice what was already being done at the better mines. In earlier years, official requirements were limited to the specification of approved lamp designs, with stipulated minimum values of luminous intensity and light output, but more recently the necessity of satisfactory maintenance of standards during service has been recognized, and the current regulations not only require that a maintenance organisation should exist, but also specify a maximum permissible depreciation below initial approval standards.'

Jan 1, 1961

By Joshua Hoffman, Braden Lusk, John Rathbun

A Flyrock Prevention Taskforce was established in Kentucky with the support of Kentucky's Department of Natural Resources, Kentucky's Explosives Industry, and the University of Kentucky. This paper presents the initial work of the Flyrock Prevention Taskforce towards its missions of identifying the root causes of flyrock incidents based on the analysis of previous events, and tracking the progress of flyrock elimination in the future. Work identifying root causes of flyrock events is presented through the development of a database which manages information about the blasts which caused flyrock. This data includes: blasting and seismograph records, drill logs, videos of the event when available, company notes/incident reports, and any additional information regarding probable cause. Work tracking the progression of flyrock elimination efforts is presented in this paper through the introduction of a flyrock index. Several metrics are proposed for this index, and are discussed for their appropriateness and shortcomings. In order for these indexes to be valid forms of tracking flyrock incident rates additional records must be kept and reported, such as the annual consumption of explosives by surface coal blasting. Suggestions for record keeping, flyrock investigation practices, and means of tracking flyrock incident rates are proposed in this paper.

Jan 1, 2013

By F. A. Seward

A1though the expanding Eltran1 configuration has been used in induced polarization exploration for several years, there has been little application of this method to straight resistivity problems. A comparison of results of resistivity exploration by this technique versus those obtained from Wenner configuration surveys reveals a number of advantages in interpretative resolution as well as in field operation. The application of electrical resistivity to ground-water exploration is well known.= In the past a major portion of this work has been accomplished by use of one or more variations of a technique employing the Wenner3 electrode configuration. With the introduction of the frequency domain technique of induced polarization measurements, used primarily in the exploration for disseminated sulfide deposits, there arose the need for an electrode configuration by which potentials could be measured externally to the current electrode spread in order to minimize coupling between current sending and potential receiving circuits. It was also deemed desirable that the configuration would provide information laterally along profile as well as with depth. To reach these objectives the expanding dipole-dipole configuration (which probably first was used in the electrical transient method of exploration and from which the name 'Eltran' was derived) has been adapted to induced polarization exploration. The author has successfully applied the same techniques

Jan 1, 1963

By S. H. Ash

NINE-TENTHS of the total anthracite deposits of North America are in Pennsylvania. Corrosion of pumping equipment by acid mine waters has been experienced at tremendous cost by mining companies in the anthracite region of Pennsylvania, for many years in many ways. The design and specifications of the large centrifugal pumps as provided in the proposed mine-drainage system (7-35, 45, 46, 48, 54, 64, 70, 71)° make it imperative that a metal or alloy be recommended that has the highest corrosion resistance and, at the same time, acceptable properties suitable for general workability (welding and machining). This report presents data on the corrosive and erosive effects of acid mine waters in the anthracite region on metals and alloys for pumping equipment and drainage facilities necessary to remove or control this water.

Jan 1, 1955

By K. Leutwyler, H. L. Bigelow

Jan 1, 1966

By Robert C. Stanley

Early History Probably the first use of nickel by man was in the fashioning of implements, and later swords, from nickel-bearing meteorites, masses of metal that have fallen from time to time at many points on the earth's surface and which consist normally of iron carrying substantial amounts of nickel. Meteorites were perhaps the first metal known to man. The falling star, sought out with fear overborne by curiosity, was found to be a better stone than the earth-given, truly a boon from the gods. Archeologists tell us there is good evidence that the ancient oriental peoples learned at an early date to make these stones into useful implements. The invincible blades of the great warriors of old in China, Persia, and in northern Europe, were Heaven-sent, a fable which sounds significant of meteoric iron. Probably some of the ancient swords of Khorassan and of Damascus were of meteoric nickel-bearing iron (1). Fifty centuries were to pass before men learned to isolate nickel and add it to iron to produce the same alloy for much the same purpose. Meanwhile, man had found another natural alloy of nickel, known first to the Chinese as paktong, or 'white copper.' It was obtained from complex copper-nickel sulphide ores of Yunnan in southern China. This metal was brought by caravan through India into Bactria, a country north of the Hindu-Kush mountains, in what is now known as Russian Turkestan. The earliest specimen extant is a Bactrian coin attributed to 235 B.C. The rough reddish-white metal was also sent in the form of triangular rings to Canton, where zinc ores were added and the whole smelted to a more malleable alloy, also known later as paktong. This alloy was the forerunner of German-or nickel-silver. Specimens of this alloy, wrought into ornamental candlesticks and boxes, were brought from Canton to Europe by the East India Company in the early days of the China trade. Paktong was highly prized for its beauty as well as its eastern origin in far-away China. By 1760 the unwrought metal was imported into England for domestic manufacture.

Jan 1, 1935

By W. E. Cassan, W. L. Eaton, James Westfield, W. M. Romisher, Karl Hughes, S. H. Ash

"INTRODUCTION Funds were made available to the Bureau of Mines, United States Department of the Interior, for anthracite investigations during the fiscal year ended June 30, 1945. One of the approved projects was to conduct inquiries and scientific and technologic investigations having a bearing on the anthradite mine-flood problem. The investigative work done from July 1,1944, to June 30, 1946, is described in previous reports (5, 8, 10, 24, 28). 6/Purpose of Report The purpose of this report is to describe the investigative work conucted by the Anthracite Food-Prevention Section, Safety Branch, Bureau of Mines, during the period July 1, 1946, to June 30, 1947,Scope of WorkInvestigative work during the fiscal year ended June 30, 1947, was conducted under the direction of D. Harrington, chief, Health and Safety Division, and S. H. Ash, chief, Safety Branch, Bureau of Mines, Washington, D. C.The broad objective of the investigative work was to obtain factual day on: 1. Anthracite reserves of Pennsylvania.2. Underground water pools.3. Barrier pillars.4. The ""buried valley"" of the Susquehanna River.5. Infiltration of surface water into underground mine workings.The above-mentioned investigations are being continued during the fiscal year July 1, 1947, to Juno 30, 1948.In addition to the investigative work covered in this report, Ash end Eaton presented a paper on barrier pillars, which proposes a method for designing barrier pillars and has been Published by the American Institute of Mining and Metallurgical Engineers (5);"

Apr 1, 1948

By C. A. Young

In-situ Fourier transform infrared/internal reflection spectroscopy (FT ?IR/IRS) has been extended to study oleate adsorption at a calcite surface. The birefringent and transmission limitations of calcite were overcome by using an appropriately designed optical setup and a near-infrared (NIR) spectrometer. An adsorption isotherm was determined at pH 9.2 and room temperature. Comparison with the fluorite/oleate adsorption isotherm determined by the same technique indicates that oleate abstraction by calcite can be as much as one order of magnitude larger than that by fluorite. Nevertheless, the hydrophobicity of the fluorite/oleate surface is greater for equivalent adsorption densities as indicated by contact angle measurements and flotation results. The monolayer region has been confirmed to be chemisorbed oleate at both calcite and fluorite surfaces. Furthermore, multichannel laser Raman spectroscopy (MLRS) showed that chemisorbed oleate at the fluorite surface undergoes a double-bond reaction with oxygen to form an epoxide/polyether complex. Such a reaction, however, could not be detected at the calcite surface. These phenomena are discussed in terms of the intrinsic surface properties of the mineral systems as well as the adsorption density and the cross-linking/polymerization reaction of the adsorbed oleate film.

Jan 1, 1993

By R. F. Kehrman

Voice Frequency (VF) electromagnetic trapped miner location devices were tested for reliability and effectiveness in 93 coal mines. Tests included uplink pulsed CW, downlink pulsed OW and downlink voice evaluations. Frequencies were 630, 1050, 1950 and 3030 Hertz. Overburden depths varied from 70 feet to 1550 feet. Successful communications were established at 91 of the 93 mines. Data indicate the transmitters and receivers will operate in practically all coal mine environments. Reliability and accuracy as location devices appear to depend on noise, depth and presence of metallic objects which distort the magnetic field. In addition, theoretical models appear to define best case situations in terms of noise and conductivity. Minor hardware problems were encountered, mostly involving battery contacts, switches and antenna cables on the receivers. No hardware problems occurred with the transmitters.

Jan 1, 1978

By W. J. Kroll

This investigation was undertaken with the idea of studying a number of unconventional methods for making chromium to determine whether production cost could be lowered and to discuss some of the more recently described processes. These comprise carbon reduction of the oxide in vacuum, nitride dissociation, fusion electrolysis of the chloride, amalgam method, iodide dissociation, calcium reduction of the oxide, hydrogen reduction of the chloride, and reduction of this compound with zinc and with magnesium. Preference is given this latter method, which is shown in a flow sheet. Special attention is given purification of the chloride and separation of the vacuum at about 900° C. A reduction method for the elimination of traces of oxide contained in pure chromium by pure hydrogen obtained from the dissociation of zirconium hydride is described. The various methods are compared in a table in the appendix. Aluminothermic and silicothermic methods for the reduction of chromium oxide and the aqueous electrolysis have been disregarded in this investigation.

Jan 1, 1950