Search Documents

By Liangying Wen, Xuewei Lv, Yuelin Qin, Feng Zhu, Guibao Qiu, Chenguang Bai, Meilong Hu, Shengfu Zhang

"The COREX process is the first reduction ironmaking technology with coal and pure oxygen to get high quality hot metal, which consumes a lot of high quality lump coal and some coke. In order to increase the utilization of fine coal, reduce coke consumption and enhance the competitiveness of the technology, the combustion behavior of pulverized coal injection in melter gasifier is studied experimentally. The results show that the combustion rate of PCI increases with the increase of temperature. And the combustion rate increases with decreasing coal particle size. Compared bituminous coal with anthracite, the former’s burning ratio is higher than the latter in the same granularity. The combustion effect is remarkable when coal blend of bituminous coal and anthracite with the smaller particle size is pulverized in COREX process.IntroductionThe COREX process is the first reduction ironmaking technology with raw coal and pure oxygen to get high quality hot metal, which consumes a lot of high quality lump coal [1-3]. However, the proportion of lump coal in raw coal is very small, and it is avoidless to produce fine coal because of mechanical coal cutter and storage and transportation process, so it is important to resolve utilization of fine coal in COREX ironmaking process in order to energy conservation and reduce the cost of hot metal [4]. Currently, Coal briquetting technology is adopted to utilization of fine coal in COREX process [5], but coal briquetting system has high investment cost and requires feasible adhesive agent. The pulverized coal injection (PCI) into a blast furnace is being used on a global scale to improve the stability and reduce the cost of blast furnace operations [6]. The successful development of PCI in blast furnace is contributed to pulverized coal in COREX melter gasifier. However, it is different in PCI process between COREX melter gasifier and blast furnace, and the differences are as follows: firstly, The air is injected into blast furnace, which temperature is about 1200 ?, but in COREX melter gasifier the normal temperature oxygen is blasted, so PCI in blast furnace begin burning in blowpipe, but the combustion of PCI in COREX melter gasifier is only in raceway. Secondly, the racway of COREX is smaller than that of blast furnace of the same size. So, the combustion behavior of PCI is complex in COREX melter gasifier, which is not use for reference."

Jan 1, 2012

By Hélio Wiebeck, Fabio J. Esper, Wildor T. Hennies, Guillermo R. Martín-Cortés, Francisco R. Valenzuela-Díaz

"Natural rubber reinforced commonly with carbon black to produce vulcanized material, turns into a new environmentally friendly nanocomposite when carbon black is replaced by organically modified clays of Brazil. Carbon black is substance derived from the oil refining process with consequent pollution to the environment. Its substitution in this industrial process must contribute to diminish the oil derived products dependence. As the added clays are only a third in weight of the traditionally carbon black added, then, to obtain the same final volume it is necessary to add low cost neutral filler that does not damage the technological characteristics of the final material. This paper presents results using as neutral filler of this type rice husk ashes from industrial wastes. Experiences realized with this nanocomposite material show results of quality and technological characteristics similar or superior to those of the rubber made with carbon black.IntroductionTraditionally rubbers are black or a very dark color. But they can have different appearance when filler of distinct composition of the carbon black is used. The carbon black is substance derived from the oil gotten during the final phases of the mineral fuel treatment with consequent pollution of the environment. Carbon black show nanometric grain sized distribution and a depth black color, because these properties it is also used for computer printers inks production. The substitution of this substance, traditionally used as a reinforced load in the rubber production, will have to contribute in such a way to diminish the dependence of these products as to diminish the pollution of the environment. The present work shows the results of the use of another kind of mineral nanoparticulate material substituting carbon black in the production of some rubber products. This nanoparticulate material is the organic modification of smectite clay treated with some types of ammonium quaternary."

Jan 1, 2008

By J. Phillip Mackey

The Peter Hayes Symposium on Pyrometallurgy, held as part of Extraction 2018, is an acknowledgement of his contributions to the basic science and principles underpinning modern pyrometallurgical processing. After completing his PhD at Strathclyde University, Scotland, in 1974, Peter took up a teaching position at The University of Queensland, Brisbane, Queensland, Australia in 1976. Peter Hayes’ research at the University since then has been focussed on: • The mechanisms and kinetics of heterogeneous solid/solid, gas/solid and liquid/ solid reactions, and • Experimental measurement of phase equilibria in complex high temperature metallurgical systems. This paper provides a brief biography of Dr. Peter Hayes and gives a full listing of Peter Hayes’ publications.

By G. G. Barbante

Copper anode slimes are a valuable source of the precious metals, and selenium and tellurium. They are mineralogically complex and this has led to a great variety of process flowsheets for treating them. The traditional pyrometallurgical method utilises oxidation in a reverberatory furnace, but has numerous shortcomings. Recently deep-bath intensive smelting methods have been developed for use in the larger refineries. Despite these process advances, the thermodynamics of the reactions involved remains poorly understood. An initial description of the thermodynamics of slimes smelting is presented, but is severely limited by a lack of basic data. It is shown that slimes smelting is superficially similar to copper converting, but has many unique features. More basic thermodynamic data on selenium-based systems are needed before the process model presented can be further refined, and work in this direction has already commenced.

Jan 1, 1994

By Bryn Harris

Much has been written over the past twenty years on the removal and chemical stabilization of arsenic from metallurgical process solutions. This paper reviews again the latest developments in this field, and concludes as before that the high-iron arsenical ferrihydrites, together with the high temperature arsenic minerals, scorodite and Type II, remain as the best and most viable vehicles for industrial control and disposal. However, a cautionary note is introduced, in that chemical environments cannot be considered in isolation, and that cogniscence has to be taken of microbiological activity in determining the disposal method. Data are also presented on a survey of industrial practice, which shows that arsenical ferrihydrite is by far the most widely-practiced and accepted method used worldwide. Finally, the disaster in Bangladesh is briefly discussed with reference to lessons that the metallurgical community might learn from this.

Jan 1, 2003

By Kiichiro Hayashi

"Indonesia is one of the world leaders in palm oil production. Palm oil industry is an industry to be considered when it comes to environmental impacts. This paper utilizes three step approaches. First, a material flow analysis of palm oil related industry was conducted in Indonesia. Second, a factory visit survey was conducted for getting information on environmental impacts of plantation and CPO mills. Third, a LCA study was made for a model Indonesian CPO mill in several bio-waste treatment options. Main findings were that, first; over 70% of FFB was bio-wastes generated from CPO mills. Second, some mills introduced a zero emission bio-waste policy. However, untreated bio-wastes in the zero emission policy, such as, CH4 from POME ponds, may have potential to reduce more impacts on the environment. Introduction Indonesia is one of the world leaders in palm oil production with approximately 12.4 million tons of crude palm oil (CPO) production in 2005 and with the plantation area 5.6 million ha spreading out in 19 provinces [10]. The expansion of palm oil cultivation in Indonesia and its export oriented industry heavily relies on the strong world market demand for food. Currently, there are 320 CPO industries in Indonesia [10]. These include plantations and palm oil related factories. Among them, there are six biggest players in CPO business in Indonesia: PT. Perkebunan Nusantara (PTPN) consisting of 9 PTPN, Sinar Mas, Raja Garuda Mas, Astra Agro Lestari, Minamas Plantation and Indofood. They are managing more than 50% of plantation estate in Indonesia and are leading the Indonesian palm oil business.Palm oil industry is an industry to be considered when it comes to environmental impacts. Unfortunately, there is not so much available information related to the performance of each CPO on environmental impacts. There are reports which provide information on environmental impacts of CPO mills in South East Asian countries, but are limited to, for instance, Thailand’s cases [4 and 5] and Malaysia’s cases [1, 3, 6, 7, 9, 11 and 12]. On the other hand, similar studies on the Indonesian’s case are not well established in academic literatures. And also there is limitation on Indonesian palm oil industrial information from plantation to consumption and disposal in academic articles. There is no literature related to material flow analysis focusing on the whole Indonesian palm oil related industry. One way to describe and present the environmental impacts is through a life cycle assessment (LCA). The LCA could be used to estimate the impacts of CPO production including the stages of plantation, transportation and milling [5, 8 and 11]. However, studies on Indonesian CPO production process were not well established in academic articles. The purpose of this paper is thus to clarify environmental impacts of palm oil industry in Indonesia especially by focusing on plantation and CPO mills with consideration to various bio-waste treatments."

Jan 1, 2008

By Petr Sulovsky, Jaroslava Ledererova, Miroslav Svoboda, Michaela Suchardova

"The thinning resources of natural raw materials necessitate an increased degree of waste material recycling. The building industry offers a range of technologies enabling incorporation of industrial wastes into building materials for construction purposes in an economically acceptable way. Our research is focused on finding the appropriate technologies for specific groups of industrial waste materials (IWM). The studied IWM involve coal combustion residues (CCR), desulphurization products, sludges, metallurgical slags, and various other wastes. Many of them contain increased amounts of toxic elements that can under certain conditions get released. In order to prevent this, each specific IWM requires finding the technology that best ensures the binding of toxic elements in the building matter are fixed for the long term.Introduction The sustainable development of mankind is more than ever viewed as a matter of resources. Many aspects of the switch from a throw-away to a recycling society concern one of the largest consumers of natural resources and producer of greenhouse gases, the building industry. One of the biggest tasks lying before the researchers in the field of building materials is to find substitute or alternative raw materials that would save the thinning reserves of natural resources. The most promising and natural way is to replace the traditional raw materials with rejected and unwanted products of industrial processes, classified as wastes. These of course are not produced with the primary intention of achieving some desired properties. The usage of industrial wastes therefore involves finding the optimal way of usage their existing positive (from the point of view of utilizations) properties and minimizing the impact of their undesired properties, i.e. from the perspective of the considered application."

Jan 1, 2008

By Luciano B. Oliveira, Luis G. C. Marques, Sergio N. Monteiro, Marcos V. M. Fagundes

"Biodiesel production is normally associated with large plantations of oily vegetables such as soybean and colza, in large rural areas. However, in the municipal limits of the city of Rio de Janeiro, southeast of Brazil, biodiesel is being produced from wastes commonly generated by typical urban activities such as sewage sludge, discarded fat from meat markets and post-used cooking oils. In the present work, the experience of producing biodiesel from urban wastes in Rio de Janeiro is assessed. The type of precursor materials, equipments and logistics are presented. The environmental and economical advantages as well as the drawbacks are discussed.IntroductionThe interest for a liquid fuel that could substitute those obtained from petroleum started more than one hundred years ago when Rudolph Diesel tested his no-spark internal combustion engine, impelled by compression, with peanut oil. By that time, petroleum was beginning to be extracted in large scale and no one was concerned with the future environmental problems and its eventual depletion. In the last century, the successful association of petroleum based fuels with the automotive industry was an almost insurmountable obstacle to any attempt to use nonmineral oils [1]. In addition to the greater efficiency and, by then, lower price of the diesel from petroleum, the use of plain vegetable oils introduced undesirable carbon deposits and reduced the engine lifetime. Today, the situation is reverse. The continuous increase in the price of petroleum and, above all, its contribution to climate changes are strongly motivating the use of biofuels to replace those obtained from fossil fuels such as petroleum, natural gas and coal [2].In the case of the common petroleum derived diesel, many countries are now engaged in large scale substitution programs. The USA should produce more than 700 million litters of biodiesel, while the European Community is expected too produce around 6.5 billion litters in 2008. In Brazil, the federal biodiesel program imposed a minimum of 2% addition to the common diesel. This would demand a production of 800 million litters in 2008 [3]. The Brazilian biodiesel is made from a diversified source of vegetables mainly castor bean, African palm and soybean. The main producers are agrobusiness firms located in large rural areas of the Brazilian hinterland [4]."

Jan 1, 2008

By Ruiling DU, Xiao YUAN, Keng Wu, Daan XU, Changyao CHAO

To utilize low grade coals to produce high quality semi-coke which can be used in blast furnaces, the pyrolysis of low grade coals was studied in this paper. According to the characteristics of coal pyrolysis process, the temperature range was divided into three parts. The interfacial chemical reaction model, random pore model and the internal diffusion model with the shrinking volume of resultant were established to describe the different ranges of pyrolysis process respectively. The results showed that the experimental data was fitted well, and all the correlation coefficients (r2) exceeded 0.97. Finally, the kinetic parameters for each temperature range have been calculated, which laid a necessary foundation for the simulation and expanded production.

Jan 1, 2016

By Kazue Moriya

At the 1980 TMS-AIME world symposium, Dr. Davey mentioned that the traditional lead blast furnace is now being challenged by direct smelting processes. In the copper smelting field both the blast furnace and reverberatory furnace are also disappearing in favour of direct smelting processes such as Outokumpu flash smelting, Mitsubishi continuous smelting, Noranda furnace, Inco furnace and so on. Those new processes all have the following in common: (1) High degree of mechanization (2) Metallurgical reactions carried out in closed vessels (3) Application of oxygen and/or oxygen enriched air (4) Minimization of handling materials and gaseous volume (5) Minimum energy requirements (6) Removal of workers from near the furnace (7) Reduction of emissions of harmful gas to meet environmental regulations. (8) Improvement to the work place environment to avoid occupational hygiene hazards. Direct and continuous smelting of powdered concentrate in one vessel was a romance of the metallurgist since early times. However as mentioned above, in the copper field this objective is being achieved in practice. The industry however can't deny that the serious and severe regulation of environmental pollution in every country was the prime motive for the modernization of smelters. In early days, to meet regulations, it was anticipated that many economic difficulties such as higher capital and energy costs and extravagant use of resources and waste disposal would be the result. "Turn a misfortune into a blessing" is an old saying which reveals the current thinking and reacent developments in the nonferrous industries. In the last ten years in the lead smelting field, about two decades later than copper, commercial scale smelting using new furnance technology has started. The KIVCET process and QSL process, which is flash smelting and bath smelting respectively, are becoming major competitors. They will be sure to upgrade their processes to remain economically and environmentally viable in the comming decade.

Jan 1, 1990

By Stephen R. Brown

Current conditions in the copper market demand that mine and plant operators make budgeted production targets at the lowest possible unit costs. For those companies bringing new production capacity on-line, achieving budgeted production levels as quickly as possible after start-up is vitally important to minimize unit costs and to begin a positive cash flow. Whether the objective is to simply improve unit costs or successfully start-up a new, complex plant, success will be strongly influenced by .the skill levels of the operators :and supervisors. The only way to assure return on plant investment, and to survive during depressed metal prices, is to ensure that plant operators have the knowledge to effectively run the plant. Technology available in computer-based, multimedia training systems, including: interactive animation, videos, voice-overs, schematics, and text can now be used to train operators at their own pace using plant-specific information. Additionally, it has been shown that learning through multimedia provides a higher degree of long term retention than more traditional learning methods.

Jan 1, 1999

By P. Tim Johnson

Relentless increases in demand for nickel and vanadium for uses such as steelmaking, catalysts and battery materials, plus the growing financial and environmental costs of their primary extraction, have led to much interest in potential secondary sources of these metals. The presence of such metals in heavy fuel oils, bitumen and related materials offers both opportunities and challenges for potential extraction methods, especially with the growing production and importance of metal-rich fossil fuels around the world. For several decades, Tetronics’ DC plasma smelting technology has been used for the recovery of metals such as nickel and chromium from stainless steel melt dusts and other wastes in compact, environmentally-friendly and efficient plants. This paper explores the suitability of DC plasma smelting as part of a wider flowsheet with feed preparation and aluminothermic reduction techniques for smaller-scale extraction operations based on this important niche secondary source of these key metals.

By Amjad Asad, Boyd Davis, Kinnor Chattopadhyay, Rüdiger Schwarze, Christoph Kratzsch, Donghui Li, Lei GAO

Sodium (Na) and Lithium (Li) are produced using molten salt electrolysis. The electrochemistry of the electrolyte is well-researched; however, there are benefits to understanding the melt flow and implications on it for cell design modifications. The basic configuration of alkali metal cells is the Downs cell. This consists of a central anode surrounded by a cathode, and this geometry was the basis for this mathematical modeling study. The behavior of gas bubbles in molten electrolyte was studied in both Na and Li cells through the use of computational fluid dynamics (CFD) techniques. The distance between the anode and the cathode was varied in the CFD model to ascertain whether strong circulatory flows would change significantly in the cell. The standard k-ε turbulence model was used to mimic turbulent flow, and a two-way coupled Discrete Phase Model (DPM) was adopted to simulate flotation behavior of chlorine bubbles and liquid metal droplets. The liquid metal distribution on the free surface was predicted using the Volume of Fluid (VOF) multi-phase model.

Mar 1, 2017

By Kurt A. M. Westerlund

The basic function of primary gas handling downstream non-ferrous pyro-metallurgical processes is cooling hot sticky gases to treatable temperature levels (e.g. entering ESP). That means managing efficient the critical gaseous components from a molten via a sticky to a solid phase. The article outlines the modem gas cooling methods combined with efficient heat recovery. Examples of the alternative use of recovered steam energy are outlined; as e.g. drying of concentrate and power generation. The heat transfer impact of the insulating dust is called fouling and circumstances causing fouling are described. Modem cooling surface design and cleaning techniques to keep fouling in reasonable limits are described. Leakage- and false air ingress into the gas handling lines often limits smelting capacity. The objective is generally to minimize the infiltration of air but it still takes place at open interfaces (e.g. at reactor hood, feed port). Leakage air at furnace roofs for example can be reduced to a minimum by adopting the pressure gas sealing used at present In-Bath-Lance furnaces. Modernization and optimization methods to de-bottleneck existing waste heat boiler gas cooling capacity by highly efficient surface cleaning systems and false air avoiding (e.g. bundle roof boxes, dust discharge) are detailed described.

Jan 1, 1999

By Frédéric Pineau, Guillaume D'Amours

Semisolid metal processing of metallic alloys takes advantage of the thixotropic behavior of material with non-dendritic microstructure to produce near-net-shape components with improved mechanical properties. The much higher apparent viscosity of the semisolid billet limits the risk of oxide formed on the free surfaces to become incorporated into the easting during the process. But, the external-skin on the periphery of the billet, which is often partially solidified and contaminated with lubricants, should not be included into the casting as this can be a cause of reject for most structural parts. In this paper, a preliminary model is set-up using the LS-DYNA SPH formulation to follow the paths of the skin. Calculations carried out show that this approach appears to be very promising to predict the paths of contaminated skins into semisolid castings. It can then be utilized to design suitable molds and gating systems.

Jan 1, 2012

By Gerson de Araújo Filho

This paper shows the use of tires as fuel to be employed into blast furnaces. The tires can substitute coal or even charcoal in the blast furnaces tuyeres. The injection into tuyeres, besides the contribution for energy generation, can also produce gas for iron oxide reduction. The tires, as powder to be injected into blast furnaces, contributes for an environmental use of this waste, which helps to obtain a high value product as well. So, the advantage of using such material is that it is waste and has lower cost for preparation. The obtained results showed that the tires have good combustibility. This one was obtained in a model that simulates the same conditions occurring in the blast furnaces tuyeres; these used raw materiais include tires and mixtures of tires with coal or even with charcoal.

Jan 1, 2006

By Gjergj Dodbiba, Atsushi Shibayama, Toyohisa Fujita, Takashi Shikazumi, Yukio Kato, Kenji Murata

"A new crushing or liberation technique by means of underwater explosion is put forward. This technique is suitable for crushing and liberating various materials, for instance: the electric parts of the discarded portable telephone, CPU from mother-boards of PCs, steel from plastics tubes used as construction materials, waste constructed materials like panels, tungsten carbide scraps, as well as slitting the optical disk (e.g. DVDs), etc. The materials to be crushed are immersed in water and then the explosion is carried out by using only a small amount of explosive. The shock waves in combination with the generated bubbles are very effective in liberating the materials of different densities. It was observed that the metals crushed or liberated by using this technique were leached much faster when compared with the conventional crushing technique. This crushing method can be applied for liberation of many kinds of electric or mechanical tools. Introduction The explosive has been used since Nobel’s invention in 1866. The main practical application of explosion is in the large scale public works, such as dam construction, land development, tunnel, mining and dismantlement of building. The shock wave caused by explosion extremely can generate high pressure able to break the concrete and rock, and other materials. In this study, the crushing and liberation of waste materials was carried out by explosion in water. The idea was to use this technique as a pretreatment stage prior to recycling. The explosion in water can be used to crush hard materials, helping the liberation between different attached materials. The samples used in this experimental work are waste materials such as construction materials, hose, cemented carbide, cellular phone, lithium buttery, DVD-R, etc."

Jan 1, 2008

By Derek Fray

Molten salts have been used for the extraction of metals since the 19th century but, recently, many interesting processes have been investigated using mixtures of molten salts and different cathodic materials. In several existing processes, the cation is simply discharged from melt but, in some cases, complications arise when the electrode potentials of the cations are relatively close. For example, the co-deposition of sodium with aluminium in the Hall-Heroult process is discussed in terms of electrode potentials of the components in the molten electrolyte. Similar considerations will also be given to the anodic reactions with respect to chlorine, oxygen, carbon dioxide or monoxide evolution from chloride-oxide melts. In some cases, the cathodic product interacts with the cathode to produce new and exciting products such as nanotubes from carbon or titanates and reduced titanium oxides from titanium dioxide. Depending on the electrode potentials, it is also possible to completely change the cathodic reaction from discharge of the cation in the salt to ionisation of the anions in the cathode. Examples are given of the reduction of metal oxides to produce metals, high technology alloys and nanomaterials and the cathodic refining of liquid metals.

Jan 1, 2006

By Anand Kumar, Pradeep kumar Jha, Suman Kant, Pradeep Kumar

"It has been a major challenge to reduce the intermixed grade formation during ladle change-over operation in continuous casting process of tundish steelmaking. The F-curve generated by step input of the tracer (new grade steel) tells about the intermixed grade amount for different grade specifications. Use of flow modifiers is beneficial in reducing the intermixed grade because of the change in slope (in different time zones) and position of the F-curve due to their placement at tundish bottom. Present study aims at investigating the role of dam placed before the outlet in a multi-strand tundish with reference to the slope behavior of F-curve in different time zones during the teeming operation plays an important role in determining the intermixed amount.Introduction In Continuous casting process, the old grade steel remaining in the tundish (reservoir between ladle and mould) from the old ladle gets mixed with new grade steel from new ladle and leads to intermixed grade which is considered to be of inferior quality. Although formation of intermixed grade is inevitable with the sequential method of casting, its amount can be controlled by changing the flow behavior of steel inside the steel. Intermixing in a slab caster tundish was simulated using 3-D numerical model based on k-å turbulence equation and compared their result with that of water model experiment Yeh and Hwang [1]. Huang and Thomas [2] reported that quantity of residual fluid in tundish affects the composition distribution in the transitional slab and thus the intermixed length. Huang and Thomas [3] developed three sub models to predict mixing in tundish, liquid core of strand and solidification. Thomas [4] developed a one dimensional model to simulate the final composition distributions in slab caster of continuous casting and investigated the effect of process variables on the intermixing. Alizadeh mehdi et al., [5] simulated of the intermixing phenomenon for slab casting for three different sub models. Goldschmidt et al. [6] developed a numerical model that predicted the location of the intermixed steel in a four line round caster. Lan and Khodadadi [7] studied for the transient fluid flow of liquid steel, heat transfer and solidification during the flying tundish change process. Cho and Kim [8] developed a mixing model to predict the outlet concentration of the tundish during grade transition. Most of the work reported in the literature has dealt with intermixing in slab caster tundish. Billet caster units are more often being used by steel industries due to growing demand of billets. The multiple outlets lead to varying degree of intermixing with time owing to their different distance (location) from the inlet. Use of flow modifier to minimize the intermixed amount, however has also not been discussed in detail so far. Further no work has been reported regarding effect of slope of F-curves obtained through different outlets on intermixing. Hence keeping these objectives in mind attempt has been made by authors to analyze the slope of Fcurves after dividing them into three different time zones and the effect of these time zones on intermixing."

Jan 1, 2012

By K. C. Liddell, B. Dou

"In producing multilayer films for magnetic data storage applications, the interfacial roughness must be controlled in order to obtain high quality materials with reproducible properties. The present understanding of the effect of roughness on multilayer properties such as magnetoresistance is sketchy, particularly for electrodeposited films. In this study, quantitative atomic force microscopy was used to characterize surface morphology before and after Ni films of varying thickness were deposited on Cu cathodes. A multinuclear multilayer growth mechanism is supported by both the deposition conditions and the AFM images, and a multinuclear multilayer model gave a satisfactory fit to measurements of the density of peaks on ultrathin Ni films between 0 and 8 nm thick.Alloys consisting of alternating ferro-and paramagnetic layers have begun to replace Permalloy in the sensing elements of magnetic hard drives. The operating principle of the new read heads is giant magnetoresistance (GMR), and they are smaller and more sensitive than previous inductive heads (1). Experimental studies on sputtered multilayers have emphasized the role of layer thickness and interlayer roughness in determining the presence and size of the GMR effect (e.g., 2,3,4,5,6). However, roughness in electrodeposited multilayers has rarely been measured, even though read heads are likely to continue to be made by this process for some time to come. Cu/Ni can be considered a model system for understanding processing-microstructure-property relationships in electrodeposited multilayers and is the most widely investigated of all such systems (e.g., 7,8,9,10,11,12). Nevertheless, the roughness of the interfaces in Cu/Ni electrodeposits has not been systematically characterized by quantitative techniques, and in all studies reported so far, the total deposit thicknesses were considerably greater than the 10 nm needed for most sensor applications (1). The thinnest such films were about 50 nm (7)."

Jan 1, 1998