Search Documents

By K. Norrena

Grade control in open pit mining requires the specification of dig limits that account for mineral grades, economic costs, and selectivity of mining equipment. Visual identification of ore rock types is ideal, but this is not always possible in lower grade disseminated deposits where ore/waste contacts are not visually discernible. In this case, conventional grade control practice consists of a two-step procedure (1) create a map of mineral grades at some selective mining unit scale, and (2) determine practical ore-waste boundaries or dig limits on the basis of the gridded block grades or assay information. This procedure is laborious, depends on a subjective assessment of where the boundary should be, and may be economically sub-optimal. We pose the determination of dig limits as an optimization problem and solve that problem with the technique of simulated annealing. Simulated annealing has the unique advantage of being able to combine multiple non-linear constraints into a single objective function. We use maximum profitability and the ability of the equipment to mine the proposed dig limits as constraints in the determination of optimal dig limits. We require a map of expected profit for eah block. Geostatistical techniques are recommended, for mapping expected profit but not necessary. Geostatistics will provide a quantification of the uncertainty in the grades within rock types using all available blasthole samples and exploration drilling. Some variant of L-optimal estimation or kriging can be used to determine the block-by-block classification that is economically optimum. We also need the expected profit for each block. It is unrealistic to assume free selection, that is, each block cannot be extracted independently of its neighbors. The optimal balance of ''accepting dilution'' and ''wasting ore'' is achieved to maximize profit subject to equipment constraints.

Jan 1, 2001

Based on X-ray phase analysis and exploratory experiments, a new technology was developed to recycle multiple valuable elements in spent Al2O3-based catalyst. The experimental results showed that after roasting at 750°C for 30 minutes at an Na2O:Al2O3 mol ratio of 1.2, the leaching recoveries of alumina, vanadium and molybdenum from the spent catalyst were 97.2%, 95.8% and 98.9%, respectively. Vanadium and molybdenum in sodium aluminate solution can be recovered by barium hydroxide and barium aluminate. The precipitation recovery of vanadium and molybdenum was 94.8% and 92.6%, respectively. Al(OH)3 is prepared from sodium aluminate solution using the carbonation decomposition process. The purity of Al2O3 is 99.9% after calcinations, and the recovery of alumina can reach 90.6% in the whole process. The Ni-Co concentrate was leached with sulfuric acid, and a nickel recovery of 98.2% and a cobalt recovery of more than 98.5% were obtained under the experimental condition of 30% (w/w) H2SO4, 80°C, a liquid: solid ratio of 8:1 (by weight), a reaction time of 4 hours and a stirring rate of 800 rpm.

Jan 1, 2007

By I. Tsolas

This paper presents the use of non-parametric approach (i.e., data envelopment analysis, DEA) for the development of environmental sustainability indicators in mineral processing using environmental, economic and/or integrated indicators (i.e., indicators that interrelate two dimensions of sustainability). A case study based on real publicly available data is presented to illustrate how the proposed approach can be implemented in practice. The merit of this approach, which is based on the productive efficiency framework, is that it provides environmental sustainability indicators that can be used internally for benchmarking purposes and externally for sustainability reporting.

Jan 1, 2008

By Tim Hurley

On Friday, May 27, 1983 at about 6 p.m., an avalanche occurred at the Revenue-Virginius Mine. Six mine personnel and two contract diamond drillers were trapped when the avalanche covered and blocked the portal, the only access into the mine. The San Juan Mountain Range in southwestern Colorado is an old volcanic caldera. It has dikes and other intrusions, many of which are mineralized with sulfide ores rich in silver, gold, lead, zinc and copper. Several peaks rise above 4,260 m (14,000 ft) and the district has been the location of avalanches dating back to prehistoric times. This is evidenced by the numerous snow-slide chutes that are infamous enough to be named on topographic maps.

Jan 1, 2006

By M. Pérez-Tello

A mathematical model to represent the expansion and fragmentation of copper matte particles oxidized under flash converting conditions is presented. The model assumes that the particles are initially nonporous, have a constant mass prior to fragmentation and travel at a constant velocity throughout the reaction chamber. The model requires the specification of the following five parameters: the particle expansion rate, a fragmentation diameter factor, a fragmentation size distribution parameter and the fractions of the finest and the coarsest particles in the feed that undergo fragmentation. The model predictions show good agreement with the experimental data collected in a laboratory furnace over a wide range of experimental conditions. The evolution of the size distribution of the particles along the reactor length was computed, and the model parameters were correlated with the experimental operating variables. Model predictions indicate that particle residence time is an important factor in the generation of dust. The presence of two maxima in the particle density function may be attributed to turbulent conditions prevailing in the furnace, which cause particles to follow different trajectories within the furnace even if they are injected at the same location.

Jan 1, 2008

By W. S. Fyfe, G. Southam, T. J. Beveridge

Bacterial populations play an active role in mineral weathering in subsurface and near-surface environments e.g., supergene enrichment of Cu at Morenci, AZ. An invitro bacterial biofilm model was used to examine the interaction between Sporosarcina ureae and ionic gold(which is toxic) or amino acid-gold complexes in gold mobility. The immobilization of ionic gold was between80-90% for 1 week but as the available, cellular reactive sites became saturated immobilization decreased to 14%within 2 weeks. In the asparagine-gold system, gold immobilization occurred at a high rate (80-90%)throughout the experiment with limited toxicity towards Sporosarcina ureae.

Jan 1, 1999

By C. Dan Kealy

Recent antipollution legislation for the control of mine tailings and waste-water has required an increasing number of tailings ponds. Many of these new waste-retention ponds are being constructed in congested locations, or the older ponds have reached such a size that--if failure occurs--they pose a threat to human life and public property. Although the typical tailings-disposal embankment represents--to the casual-, observer or the economy-minded mine official--a rather ugly but benign and stable pile of waste, they are in fact an extremely sensitive structural mass, retained behind the frailest of dikes. Failure of the waste mass requires only a minor change in water retention or weather conditions, erosion or piping of the ground strata, shifts in load or slight earth tremors. When failures occur, the results can be disastrous. In the U.S., we have been fortunate that, so far, pond failures have not caused loss of life. Thus, failures in this country have attracted little public attention. Present tailings-pond construction methods used by the mining industry require the barest money investment, and little engineering effort. Unfortunately, this superficial approach may increase short-term profits, but the practice may be conducive to the construction of needlessly weak structures. In coming years many of these designs will probaly become corporate liabilities. A typical pond is portrayed in Figure IA. This particular pond in Arizona is 1 mile long and 3/4 mile wide. Illustrated in Figure lB is a representative pond in cross section. This paper in concerned with two basic features common to all tailings disposal: (1) location of the phreatic surface within a tailings-pond embankment because of its influence on embankment-slope stability, and (2) prediction of

Jan 1, 1971

By A. El-Midany

Dolomite impurities are increasing in the currently mined phosphate deposits in Florida. Several research efforts have been conducted in various laboratories around the globe to find methods to economically removing the dolomite. However, a universal and cost-effective process is not now in commercial use. In this paper, a new process for dolomite/apatite separation is presented. The differential solubility of dolomite in slightly acidic solution is utilized to generate micro CO2 bubbles at the dolomite/water interface. Particle (dolomite)/bubble aggregates float to the surface leaving phosphate concentrate with low MgO content. Interestingly, up to 6.0 mm particles can be floated by such micro-bubble/particle aggregates. Different surface-active agents were tested to stabilize the bubbles. Results of these tests are presented, and the mechanisms involved are discussed.

Jan 1, 2009

By C. Pattenden

The viability, self-reliance and resilience of small communities are perennial challenges in regional Australia. Recent developments in Australian mining regions seek to govern the minerals industry in a more holistic way that contributes to sustainable futures for affected communities in different contexts. In some areas of the State of Queensland land use conflicts and the cumulative impacts of multiple projects and activities across time and space have come to the fore. In more isolated regions of Western Australia the dominant issues relate to overstretching people, infrastructure and services in predominantly mining towns. In both cases, there is an ambition for regional towns with a strong extractive industry presence to transition into desirable, liveable and affordable cities with a diversified economy. The paper analyses two strategies - the Pilbara Plan in Western Australia, and the Sustainable Resource Communities Policy in Queensland - to identify how these governance instruments are contributing to sustainable development.

Jan 1, 2011

By L. Franko, S. Klima

Wet-drum magnetic separators are used extensively for upgrading iron ore and for magnetite recovery in dense-medium circuits. In this study the performance of a continuous, laboratory wet-drum magnetic separator was evaluated with and without the application of ultrasonic energy when processing dense medium slurries. Test variables included magnetic-to-nonmagnetic ratio, solids concentration, and nonmagnetic materials. The results indicate that under certain conditions, the purity of the magnetic material increased after ultrasonic treatment.

Jan 1, 2001

By V. Galla

Waste rock facilities (WRF) generally have a large footprint depending on the strip ratio the mine plan provides. Considerable planning is involved during the initial phase of the mine plan regarding the location of the WRF. As the mining operations are commenced the locations of the WRF change accordingly with the variations in the mine plan involving feedback and support from local communities and stakeholders. Waste rock facilities management becomes challenging when the area available for placement is limited due to terrain topography, environmental and permitting constraints. Risks associated in the design of waste rock facilities constitute particle size of rock, chemistry associated with the rock for reactivity and stability of the over all facility. This paper will provide some insights on designing, scheduling and managing a WRF. Emphasis on geotechnical, geophysics and geochemistry aspects of waste rock with reference to design, construction process and scheduling of WRF are also presented. Design improvements in the reclamation slope of WRF for erosion control will be discussed. Continuous improvement (CI) methodology will be introduced in the process of WRF operations. Current practices and future recommendations towards sustainability and consistency in operating WRF will be discussed in conclusion.

Jan 1, 2011

By Wern-ping Chen

Technical and non-technical challenges exist in each mega infrastructure project. It?s no exception to the first US underground PPP Port of Miami Tunnel (POMT) project in Miami, FL. The POMT will connect two man-made islands, the Dodge and the Watson Islands, under the Biscayne Bay within highly porous limestone formation. Permeability as high as 0.1 cm/sec has been identified. Its 41-ft outside diameter, if constructed, is the largest precast segment lining in the US. Besides its geological and hydro geological challenges and risks, local community influence and impacts have controlled the fate of this project. This paper describes its tender design enhancements and the evolving of its slow advancement in resolving local community issues.

Scattered north and south along a 161-km (100-mile) stretch of Interstate 80, Newmont Min¬ing Corp. owns four active mining properties in Nevada?s northern high desert ? Carlin Trend Operations, Midas, Twin Creeks and Phoenix. Among the four, there are nine openpits, five underground mines and 14 processing facilities. While gold is the predominant ore, silver and copper are also produced. And in a move to hold down energy costs, Newmont built and owns the 200-MW (net), coal-fired TS power plant. This plant provides about 65 percent of the power used for Newmont?s own operations, while the rest is sold to NV Energy, which services Nevada and northeastern California. Bringing the Phoenix Mine ? Newmont?s newest in Nevada ? on-line presented many developmental and operational challenges. Located about 19 km (12 miles) southwest of the town of Battle Mountain, the general area had been home to prospectors and other mining companies since the 1860s. But any profitability in developing the lower grade gold, copper and silver deposit at Phoenix proved elusive, with Battle Mountain Gold being the last company to make an attempt. When Newmont acquired Battle Mountain Gold and its Phoenix reserves in 2001, the lower grade of ore was not a deterrent. Newmont found Nevada-wide cost savings synergies for maximizing profit during the depressed gold market of the late 1990s. The new property was aptly renamed the Phoenix Mine, a nod to its rising from the ashes of the dreams and efforts of previous mine owners.

Jan 2, 2010

Adverse ground behavior events, such as convergence and falls of ground, are some of the most significant challenges and hazards in underground mines. Our goal is to work toward mine-wide, digital, and real-time three-dimensional geotechnical situational awareness and predictive capabilities in complex underground mining operations. This will benefit operators, engineers, and management by enabling them to develop a more proactive approach to ground control. To this end, and inspired by research in the field of remote sensing and autonomous robotics, this paper assesses the potential of mobile light detection and ranging (LiDAR) data acquisition for high-frequency, high-accuracy monitoring tasks in Global Navigation Satellite Systems (GNSS) deprived underground mines. Limitations of current monitoring practices are reviewed. Relevant academic and commercial developments in the fields of indoor mobile mapping systems (MMSs) and simultaneous localization and mapping (SLAM), robust autonomous robotic platforms, and automated remote sensing data processing are highlighted, and their current shortfalls are evaluated. To conclude, the ramifications of this work for the development of future autonomous underground mine monitoring solutions are discussed.

Jul 28, 2020

By W. Blake, J. Whyatt

Sixty years of rockbursting in the Coeur d’Alene district has taught painful lessons and led to a number of practical advances in controlling rockburst hazards. This paper summarizes those lessons, concentrating on practical measures that have been successfully adopted to reduce hazards. These lessons are explained in the context of district mining history and current understanding of rockburst phenomena. Overall, the paper provides the practicing mine engineer with an appreciation of rockburst hazards and an overview of practical measures that can be used to control these hazards in the context of Coeur d’Alene district experience.

Jan 1, 2002

By Steve J. Czehura

The Butte quartz monzonite is the host rock for early porphyry copper style mineralization and subsequent mesothermal-epithermal, enargite-gold style veining that transects the district. The east-west Anaconda system veins sustained mining for over a century. They include the Emma, Anaconda-Original, Syndicate, Badger-State and Alice-Rainbow veins, each with strike lengths of more than 3,660-m (12,000-ft) and vertical continuity in excess of 1,370-m (4,500-ft) with mining widths from 1.5- to 15-m (5- to 50-ft). These characteristics are unique to Butte. The incredible dimensions and tenor of these veins have yet to be surpassed and Butte is still touted as being the “Richest Hill on Earth.” The Anaconda Company was formed in 1895 to develop underground copper reserves in the district. It eventually consolidated all operations under one company. Production from underground mining continued through the mid-1970s. Openpit mining in the Berkeley pit began in 1955 with the extraction of supergene ores, along with the remnants of deeper horsetail zones inaccessible to the underground mines.

Jan 1, 2006

By Q. J. Browne, M. A. Miller

Silver Bell produces about 22,000T of fine copper annually from low-grade chalcocite and oxidized copper ore that is recovered by sulfuric acid leaching and SX-EW processing. The current mineable reserves are 146 million short tons averaging 0.39% Cu, at a 0.15% cutoff. Silver Bell utilizes two types of mining methods to develop the low-grade reserves: (1) a conventional blast, load and haul method for run-of-mine leach ore, and (2) rubblization of material on the margins of existing pits. Rubble leach ore is blasted, terraced with a bulldozer, and leached in place. Mining and/or rubble leaching is currently active in four separate pits. Laramide-age intrusive rocks host porphyry copper mineralization at Silver Bell. Quartz monzonite porphyry dikes and stocks, mafic-poor equigranular granite (alaskite), and sub-volcanic dacite porphyry are the predominant host rocks. Most of the ore currently mined comes from near-horizontal enrichment zones containing veinlets and disseminated grains of pyrite and chalcopyrite rimmed by chalcocite. Conversion from a milling operation to a leach only operation allowed for a much lower cutoff grade than was historically used at Silver Bell. Mine geologists were able to increase copper resources by drilling exploration targets that were previously interpreted to provide lower-grade mineralization below cutoff-grade for milling. Geologic parameters that effect the distribution of rubble and mineable leach ore include: ore grade and thickness, variable alteration styles in intrusive host rocks that affect fragmentation during blasting, acid consuming carbonate wallrocks (reactive skarn) which influence leach solution pH, solution flow paths and drainage, presence of leachable oxide mineralization in non-reactive skarn, and depth to hypogene mineralization which is currently uneconomic. Geologic parameters are used to predict rubble bench limits, vary blast hole spacing for consistent fragmentation, and correct errors in mineral zone classification based solely on blast hole assays. An expansion-drilling program has identified approximately 150 million tons of new leachable copper resources with an average grade of 0.35% Cu.

Jan 1, 2002

As ore deposits become finer grained the requirements for regrinding before cleaning or leaching have increased substantially. Despite this increasing need, there is no standard test to predict grinding energy requirement below 70 microns. The standard Bond Mill test applies for coarser ball milling, but is not appropriate for stirred milling with fine media grinding to 70 microns. With no industry -standard test, the energy requirement is often made on the basis of supplier estimates or benchmarking against similar applications. Yet suppliers use vastly different scale-up methods which result in widely different energy estimates. Estimates can differ by 100-300% even for similar mills. This must result in serious errors to install either too much or too little grinding power. This paper explores this by comparing the actual performance of full scale regrind mills against their original design estimate. It confirms that serious scale-up errors have been made, and have then been perpetuated by ?benchmarking?. The test conditions to achieve accurate power estimation are discussed. The essential test conditions are: continuous (not batch) tests, ensure steady state (no coarse fraction retained in test mill), correctly account for classification, measure energy directly (not inferred), and using the same media size as the full scale installation. Failure to correctly address even one of these factors can bias results by 40%; failure to address several multiplies the error.

Jan 1, 2011

By S. D. Bearden

Color enhances expression and communication in all physical objects experienced in life. Pigments provide color and in some applications have a specific additional function. Natural iron oxides are widely distributed throughout the world but only a few deposits are sufficiently pure and possess acceptable color and brightness properties to merit their processing into pigment form. Ochre, the common name for goethite ore, is the best and most under used material in the buff colored pigment market. The geological occurrence of ochre in the basal Shady Formation of the Cartersville Mining District (Georgia) is described. Exploration, processing, and product applications of New Riverside Ochre Company, Inc. are discussed. An overview of the worldwide pigment market is presented with emphasis placed upon the North American activity in iron oxide production and application. The purpose of this paper is to increase the awareness of ochre and its potential market in the colored iron oxide pigment industry, encourage research on the origin of ochre deposits, and stimulate interest in new applications of this unique substance.

Feb 27, 2013

By H. -J. Langhoff

"The paper describes not a result, but a starting point to implement sustainable development to a region characterized by a typical down river landscape, agriculture, and extractive industry. The NaturFreizeitNiederrhein GmbH (NFN) is a private company with associates from administrative bodies, the local mining companies and multiple representatives of environmental protection groups (local and national), tourism organizations, cultural societies and also aquatic sport and fishing clubs. Center of the concept is the "NFN Lake District." The development concept aims to provide the agricultural industry with alternative means of income, while protecting wildlife and the ecological balance as well as preserving the social und cultural system and enhance the safety against flooding from the river Rhine. The mining industry contributes their coordination of obligation concerning reclamation and recultivation of the already existing individual projects. While designing the landscape components and establishing the infrastructure for the different tasks, the production of gravel and sand is yield as a by product. The result is a long term perspective for region and industry."

Jan 1, 2005