Search Documents

By J. H. Viljoen, C. H. Graan, N. B. Strydom, J. S. Greyson

M J Martinson (Fellow) There is everywhere a lamentable dearth of quantitative information on occupational factors affecting the health and safety of mineworkers, and as the authors point out in their introduction underground lighting is one of the factors which has received little attention in South Africa prior to this welcome paper. Since the authors are to some extent pioneering, it is perhaps inevitable that the paper should raise more questions than it answers, but nevertheless it provides a provisional yardstick against which the need for, and success of, remedial action may be judged. Before commenting in detail on a few aspects of the paper it may be worthwhile to summarize the statutory provisions relating to underground lighting, contained in Chapter 15 of the Regulations promulgated in terms of the Mines and Works Act 27 of 1956. Chapter 15 is entitled `Lighting, Safety Lamps and Contraband', but in the context of the present paper only four simple regulations need be noted: firstly, no person shall work or travel in an unilluminated part of a mine unless he carries a light ; secondly, adequate stationary lights shall be provided at stations and certain other localities in shafts, winzes and places used for winding; thirdly, mechanically propelled conveyances shall be provided with an effective bright light shining in the direction of travel; and fourthly, moving machinery to which personnel have access shall be illuminated so as to be clearly visible. In all four regulations the standard of lighting to be provided is wholly subjective, and under these circumstances the wide inter- and intra-mine variations in light intensity disclosed by the study are hardly unexpected. Nevertheless the data presented in the authors' Table I raise three points (1) Is there any evidence that the 19 mines visited during the survey are representative of the 45-50 large gold mines in South Africa, or that the shafts selected are representative of the respective mines? Mine managers would scarcely be human were they not to offer better lit working places for the survey; perhaps the use of a scaling factor (e.g. tonnes or transit mineworkers per shift, kilowatts, etc.) for each working place might have helped to put the figures in perspective. (2) Looking at two of the more numerous - and probably important - of the ten working places included in the survey, i.e. stations and tips, one is struck by the marked. skewness of both intensity distributions (with higher frequencies at the lower intensities) and the abrupt cut-off in both cases just short of pitch darkness. Thus, of the 45 meaned readings recorded at 26 tips no less than 19 fall in the lowest range of 0,1-0,9 1m/ft2, with but one tip in total darkness; of 46 readings on 26 stations, 7 fall in the lowest range and none is in total dark-'1 ness. Although a light with an intensity in the range 0,1-0,9 1m/ft2 may satisfy the regulations, it is certainly arguable that in some situations it may be safer to have no light at all. (3) In view of the skewness referred to above, one wonders how meaningful are the `total average light intensities for (the gold mining) industry' quoted in Table I, which the authors compare with illumina¬tion levels found in other countries. Looking at tips again, one notes that 34 out of 45 meaned intensity readings fall below the `total average' for tips, and only 10 exceed it. From this it may be concluded that a few well-lit working places included in a `total average' may conceal a plethora in Stygian gloom. In their discussion the authors make fleeting reference to the effect of underground lighting on productivity and accident rates, without however quoting any South African experience in this regard. Intuitively it seems highly likely that better lighting (in the widest sense) would improve productivity and reduce accidents, and of course it is in these areas that the mining industry might seek economic justification for providing better lighting. It is all the more regrettable therefore that these factors were not studied simultaneously with the present investigation, especially at the Psychological Division of the Human Sciences Laboratory has recently published a study on underground accidents in the gold mining industry without making any reference whatsoever to lighting as a causal factor. In the event neither of the two studies enables us to make an economic appreciation of the situation, and this seems to be a classic example of a situation where some dovetailing of research effort would have greatly increased the useful return. On the effect of lighting on accidents, it may be noted that in 1939 Mickel presented some very interesting statistics to the Mine Managers Association of the Transvaal2, on the improvement in accident rates which followed the random issue of electric cap lamps to native mineworkers in the Hercules Section of E.R.P.M. the previous year. Based on a 12 month trial period in which 250 000 shifts were worked with carbide lamps and (contemporaneously) 307 000 shifts with cap lamps, the incidence of major accidents (at least one day in hospital among men using carbide lamps was 1,15 accidents per 1000 shifts, while the incidence of minor accidents (requiring dressing only) was 11,52 per 1 000 shifts. The corresponding figures for men using cap lamps were 0,79 and 7,31 accidents per 1 000 shifts respectively, representing a reduction of over 30 per cent in both major and minor accidents. While these figures are obviously dated - only men using cap lamps were issued with hard hats, for instance - they do indicate a need for similar research today.

Jan 1, 1971

By L. Pretorius, S. Uludağ

This paper explores how to apply system dynamics principles to surface mining problems towards understanding the consequences of mining efficiencies. Some simulation examples related to machine and people performance have been used to demonstrate systems engineering concepts to mining engineers. The simulation tool used is Vensim, which is widely used in industrial engineering applicable to systems thinking, and systems dynamics. The science and mathematics behind the system dynamics as well as benefits and typical challenges are discussed to explore the applicability to mining problems. The benefit of having one less drill is easily quantifiable with the developed model which is one of many other measurable benefits, using the developed model. Some of the benefits of the improved quality of drill holes are not fully quantified as this depends on the mine specific inputs. There are examples of quantifying this in the other industries using system dynamics tools.

Sep 1, 2021

By J. N. Van der Merwe

"The probability of survival of coal pillars is a more rational indicator of stability than the safety factor. Over time, pillars undergo reduction in size by progressive scaling of the sidewalls. The probability of survival is therefore not constant but reduces over time. The rate of scaling can be quantified, and the reduction of the probability of survival as a function of time can therefore also be quantified. The paper describes the link between the factor of safety, probability of survival, and reduction of the probability of survival. Using the safety factor, probability of survival, and the time at which the probability of survival will reduce to 50% is proposed as a more rational method of evaluating pillar stability than the safety factor alone.IntroductionCoal pillar strength has long been the subject of research in South Africa and several other coal-producing countries. However, it began receiving serious attention only after the Coalbrook disaster in 1960. The most important outcomes of the initial investigations were the groundbreaking research by Salamon and Munro (1967) that resulted in the well-known power formula for pillar strength, and the work by Bieniawski (1969) that resulted in a linear formula for strength. The former approach was based on empirical back-analysis of failed and stable pillar cases, and the latter on in situ strength tests on large specimens.The Salamon and Munro (1967) formula has been widely used in South Africa and even adapted for application to hard rock pillars by researchers such as Hedley and Grant (1972).At the time of the initial work by Salamon and Munro, there were only 27 failed pillar cases suitable for analysis. It was not possible at the time to determine site- or seam-specific strength, and the result was a general formula for use in all seams in all mining districts. Since that time pillars have continued to fail and the database continued to grow – as of 2013, there were 85 cases in the database. Using the additional data, there have been a number of re-evaluations of the strength formula and it has also become possible to differentiate between the different mining seams and areas."

Jan 1, 2016

By M. Mathey

The application of the Monte Carlo technique to production planning and everyday economic decisionmaking in mine production management is demonstrated. The logic is detailed using an example of underground production with continuous miners (CMs) and truck haulage. It is argued that availability of equipment and personnel are the predominant variables influencing mine output and productivity and that those availabilities may be well represented by binomial probability distributions. The probabilistic model is implemented in a standard Excel® spreadsheet with Palisade’s @Risk add-on to facilitate simulations. Starting from model calibration against data obtained from a mine’s annual reports, some general interdependencies of availability, utilization, productivity, and costs of production processes are outlined. Finally, several possible options and their consequences as regards production improvements are explored.

Dec 13, 2022

By T. Szendrei, S. Tose

The fracturing and movement of rock that occurs in the vicinity of a stemmed borehole charge in open pit mining operations are described by examining the effects of the emitted stress waves – shock and elastic – and the expansion of high-pressure detonation product gases. Three principal modes of momentum transfer to fractured rock are identified, all linked to gas expansion work. This work can be delivered radially (burden), axially (stemming), and in the collar zone (cratering). Flyrock is generated under unusual combinations of blast parameters and rock properties. Although infrequent and seldom predictable, the generation of flyrock can nonetheless be interpreted and modelled in terms of the principal mechanisms of rock projection described in this study. The physical processes underlying these principal mechanisms are identified and will permit the development of predictive models for flyrock velocities.

Dec 13, 2023

By N. Snyders, I. Mwandawande, S. M. Bradshaw, M. Karimi

"Computational fluid dynamics (CFD) was applied to predict the average gas holdup and the axial gas holdup variation in a 13.5 m high cylindrical column 0.91 m diameter. The column was operating in batch mode. A Eulerian-Eulerian multiphase approach with appropriate interphase momentum exchange terms was applied to simulate the gas-liquid flow inside the column. Turbulence in the continuous phase was modelled using the k-_ realizable turbulence model. The predicted average gas holdup values were in good agreement with experimental data. The axial gas holdup prediction was generally good for the middle and top parts of the column, but was over-predicted for the bottom part of the column. Bubble velocity profiles were observed in which the axial velocity of the air bubbles decreased with height in the column. This may be related to the upward increase in gas holdup in the column. Simulations were also conducted to compare the gas holdup predicted with the universal, the Schiller-Naumann, and the Morsi-Alexander drag models. The gas holdup predictions for the three drag models were not significantly different. IntroductionColumn flotation is an important concentration technology that is used in the mineral processing and coal beneficiation industries. The growing interest in the use of column flotation in mineral processing has been attributed to the simpler flotation circuits and improved metallurgical performance compared to conventional flotation cells (Finch and Dobby, 1990). Flotation columns have also found other applications outside mineral processing, such as de-inking of recycled paper (Finch and Hardie, 1999).In column flotation, a rising swarm of air bubbles generated by means of air spargers is employed to collect the valuable mineral particles and separate them from the gangue minerals in a countercurrent process. Wash water, which is continuously fed at the top of the column, is used to eliminate entrained particles and stabilize the froth. The column volume can be divided into two sections – the collection zone in which the bubbles collect the floatable mineral particles, and the cleaning zone (or froth zone) where product upgrading is enhanced through the removal of unwanted particles entrained in the water mixed with bubbles from the collection zone."

Jan 1, 2019

By N. V. Moraka

In dealing with transformational aspects, the South African Constitution aspires for a balance between attempts to broadly represent the country’s demographics in the way in which organizations are structured and the need to maintain the necessary skills to ensure continual retention of skills for optimum and efficient organizational performance. Through the Mining Charter, government aimed to redress gender and racial imbalances in the mining industry as part of transforming the demographic representation of mining companies to include black people, women, and people living with disabilities in all job levels up to top management. While the Constitution calls for an appropriate balance between demographic representation and competency, this aspiration for mining poses challenges for companies due to the proficient and competent skills needed in this industry. To this end, the South African mining industry has been subjected to substantial criticism from government regarding the slow progress of transformation. The mining industry justifies its slow pace of transformation by pointing at inconsistent, varying legislation and definitions governing transformation, limited skills available from historically disadvantaged groups, and cautioning not to compromise the sustainability of mining companies by marginalizing white males and white youth with the objective of addressing racial imbalances. This lack of understanding between industry and the government has led to considerable confusion regarding the accountability of stakeholders in transforming the industry. This article presents the perspectives of ten mining executives on transformation in the South African mining industry. The theoretical description of transformation, as well as other mining stakeholders’ interpretations of transformation. is presented. Qualitative data from interviews with mining executives demonstrates their understanding of transformation through rich descriptions, interpretations, and implications in their contexts. The findings demonstrate that transformation in the mining industry is not simply about race and gender, but about cultural change, a change in mind-sets, embracing diversity, equalizing rights and opportunities, and attaining social justice. Moreover, transformation is clearly a gradual process. The article concludes with a recommendation for the definition of transformation to be corroborated with the views of mining executives and that of the Constitution of South Africa. This will create an overarching, simplified definition of transformation that can be accepted and interpreted by all stakeholders.

Jan 1, 2016

By B. Oladipo, E. Govender-Opitz, T. V. Ojumu

Bioleaching, one of the several important processes of biohydrometallurgy is an accepted technique for the extraction of desired metals from sulphide ores. Although the mechanism is well understood, the slow metal extraction rate due to passivating layer and ferric ion precipitation, especially in a typical chalcopyrite leaching, impact negatively on the overall efficiency of the process. Iron precipitates are common in many biohydrometallurgical operations and these precipitates represent the exit route for undesired iron, alkali ions or sulphate ion from the processing circuit. While there have been reports on approaches to slow the formation of these precipitates by manipulation of various operating conditions such as pH, redox potential and temperature, the precipitates become highly significant over the long term in the continuous operation of bioleaching and may render heap impermeable. Although there is evidence supporting the nature of the passivation to be precipitates of iron, their scavenging mode of reducing extraction efficiency is still not well understood. This paper thus discusses iron precipitation in biohydrometallurgical processes, including its formation and significance on bioleach processes. The paper also details the associated passivating species identified with heap bioleaching of sulphide minerals and provides some insight into sorption mechanism that limits metal recovery in a typical bioleach operation. Keywords: Iron precipitation, bioleaching, chalcopyrite, passivation, jarosite, metal sorption

Jan 1, 2020

By B. k. Kenzhaliyev, M. A. Naimanbayev, Zh. A. Baltabekova, N. G. Lokhova

In research various desorbents were used to desorb the following rare-earth metals from Purosorb 140 cation exchanger, i.e. ammonium chloride; ammonium sulfate; a mixture of nitric acid and ammonium nitrate; a mixture of hydrochloric acid and ammonium chloride; a mixture of sulfuric acid and ammonium sulfate. It was established that a solution containing 30 g/dm3 of H2SO4 + 300 g/dm3 of (NH4) 2SO4 is the most optimal desorbing solution to desorb REMs from macroporous Purosorb 140 cation exchanger impregnated with rare-earth metals from industrial dihydrate wet-process phosphoric acid. It was established that the residual REM content in the cation exchanger decreased from 0.89 to 0.10 wt. % with an increase in the ammonium sulfate concentration from 10 to 400 g/dm3. Technological desorption regimes for rare-earth metals from cation exchanger were developed. The optimal conditions were determined to desorb rare-earth metals from the Purosorb 140 cation exchanger, particularly temperature 25°C; L:S ratio = (0.8 ÷ 1.1):1; duration = 1.0-1.5 hours. Keywords: Rare elements, sorption, cation exchangers, wet-process phosphoric acid, desorption

Jan 1, 2020

By J. O. Mogalanyane, N. Naudé, A. M. Garbers-Craig

The fines produced is not suitable as feed material for the subsequent rotary kiln and the electrical arc furnace. The need for briquetting the ferronickel ore is premised on the minimisation of fine particles in the rotary kiln as well as improving charge permeability in the furnace, and improving overall process safety. Briquetting may be defined as an agglomeration method in which fine particles are compressed under pressure. It consists of three different technologies: vibropressing, roller pressing and stiff extrusion. The current study focuses on evaluating the performance of ferronickel briquettes generated, using roller-pressing technology. Physical properties, chemical properties and metallurgical properties of the briquettes were used to evaluate their performance and quality. Standard ISO tests for iron ore pellets were used. Size degradation as a result of reduction was measured using the ISO 4696-1 test. The decrepitation of the briquettes at the point of entry into the rotary kiln was evaluated using the ISO 8371 test method at a temperature of 700oC. The degree of reduction was evaluated using the ISO 4695 test procedure. Average green briquette compressive strength of 559 N was reported at a moisture content of 16% with an average drop number of 19.1. Increasing the moisture content has a detrimental effect on both the compressive strength and the green briquette yield. The drop number is expressed as the number of drops until breakage, when a briquette is dropped from a 1 m height, decreased with an increase in moisture content. At a moisture content of 16% an average green briquette yield of 85.1% was reported. Keywords: Ferronickel briquettes, moisture content, curing conditions, physical properties, chemical properties

Jan 1, 2020

By J. A. L. Napier

It has been established that significant time-dependent stope convergence may occur over time periods of hours and days in certain hard-rock gold and platinum mines. The source of this time-dependent behaviour appears to be associated with both pre-existing discontinuities and with mining-induced fractures that form near the stope face. These induced fractures may be associated with blasting processes and may also be formed in response to high stress concentrations in the unmined regions immediately ahead of the stope face. In shallower platinum mining operations, time-dependent behaviour is, however, observed to be much less marked unless some form of specific mining-induced fracturing occurs. One particular case of considerable interest is the time-dependent behaviour that is found to be associated with the formation and deployment of crush pillars. The purpose of the paper is to present a simple limit-equilibrium computational model of this behaviour that is sensitive to both the formation sequence and the size of planned crush pillars in a mine layout. This model provides a useful means to optimize the sizing of crush pillars, and at the same time may be used to identify potentially hazardous circumstances in which pillars may not crush in a stable manner.

Jan 1, 2012

By G. Popplewel

Commencing with the Pre-Feasibility Study (PFS) conclusions, the Orapa 3 process design evolved through a phase of value-engineering studies. An overall re-evaluation of the originally proposed process design was necessary both in order to address the interim increase in target throughput from 9.8 Mtpa to 12 Mtpa as well as to increase capital efficiency. In the interests of clarity, the PFS process design for Orapa 3 has been omitted from this paper, as it is no longer relevant. Recognition is however due to those engaged in earlier phases of the Orapa 3 project with respect to fundamental mass-balancing modelling; and ore and diamond characterization, which fanned the basis for the process design that has evolved from feasibility study activities.

Jan 1, 2010

By J. Pelders, G. Nelson

"Fatigue is a significant concern in the mining industry as it is a causal or contributing factor in many incidents and accidents. Fatigue can be caused by work- and non-work-related factors. There is a lack of information about associations between demographic and other non-work factors, and fatigue. This study aimed to assess associations between demographic, work, living, and socioeconomic conditions, and lifestyle characteristics, and fatigue at a platinum smelter in South Africa. Eight interviews with management and two focus groups with production workers were conducted, and 75 questionnaires were completed by production and other workers. Both work- and non-work-related factors were considered to be causes of fatigue. These factors included overtime, shift work, high workloads, activities performed outside of work, age, race, housing tenure, diet, sleep disorders, stress, and job satisfaction. In general, higher levels of fatigue were reported by younger participants, those who rented accommodation, ate less healthily, had a sleep disorder, and those with high levels of stress and low job satisfaction. As various demographic, lifestyle, and wellness-related factors were associated with fatigue, both work and non-work contributors should be addressed in fatigue management plans. BackgroundFatigue may be defined as ‘a state of impaired mental and/or physical performance and lowered alertness arising as a result of, or a combination of, hard physical and mental work, health and psychosocial factors or inadequate restorative sleep’ (BHP Billiton, 2005). Williamson et al. (2011) define fatigue as a biological drive for recuperative rest. Sleepiness and fatigue are related, and the terms are often used interchangeably. However, sleepiness, more specifically, can be defined as sleep propensity, or a person’s tendency to fall asleep (Hossain et al., 2003; Shen, Barbera, and Shapiro, 2006).Increasing levels of fatigue and sleepiness are associated with lapses in attention, errors, response slowing, fluctuations in alertness and effort, and impaired attention, working memory, long-term memory, decision-making, and creativity (Alhola and Polo-Kantola, 2007; van Dongen and Dinges, 2000). Fatigue is also associated with adverse effects on mood and impulsive behaviours (Alhola and Polo- Kantola, 2007; Minkel et al., 2011; Schwarz et al., 2013). It is a significant concern in the mining industry as it is commonly identified as a causal or contributing factor in many accidents and injuries (Schutte, 2009). Fatigue can also lead to long-term health problems, including digestive problems, heart disease, stress, and mental illness (Shaw, 2003)."

Mar 1, 2019

By S. Mohanta, B. C. Melkap

"SynopsisDry beneficiation of coal by air dense medium fluidized bed is an emerging trend. It is widely believed that the particle size of the medium has a significant effect on the separation efficiency. This investigation demonstrates that medium particle size has a major effect on separation efficiency. Experimental results show that different size fractions of the same feed respond differently to the same size fraction of medium solids. Furthermore, a particular size fraction of feed coal responds differently with different size fractions of medium solids. The Ep values and overall metallurgical performance parameters, obtained from experimental results, clearly indicate the superior performance of an air dense medium fluidized bed separator when using –150+106 µm magnetite powder as the fluidizing medium. These observations reinforce the importance of sizing the medium particle size for the air dense medium fluidized bed.IntroductionIn an air dense medium fluidized bed (ADMFB), a fluidizing bed of a particular density is created by suspending solid particles in an upward air flow. A feed containing coal particles of different densities is introduced into this fluidizing bed. The particles with relative density less than the bed density float on the top of the bed, while particles denser than the bed density sink through it. Since there is a general correlation between ash content and density of coal particles, it is possible to remove ash-forming impurities from a raw coal to the required level by regulating the density of the fluidizing bed. Recently, the ADMFB process has received significant attention world-wide for its specific advantages of low operating cost and less restrictive for small capacities (Luo and Chen, 2001; Houwelingen and de Jong, 2004; Dwari and Hanumantha Rao, 2007; Sahu et al., 2009; Mohanta et al., 2012). This process is not recognized as a well-established industrial practice because of the availability of efficient wet processing technology. However, with the revival of interest in dry beneficiation of coal in general, and ADMFB in particular, there is a concerted effort to improve the efficiency of the ADMFB process, and successive improvements have made the process a competitive and viable option for beneficiating coal."

Jan 1, 2015

By J. Bal, V. D. Dao, W. Li

"SynopsisThis study proposes a methodology for evaluating the risk of coal bumps in multiple-seam longwall mining. Both the stress field and the total energy release (TER) during retreat were evaluated in the specified case involving multiple-seam mining using the LaModel program. The results of numerical simulations indicated that both the peak vertical stresses on the panel edges and the peak TERs in the outby longwalls increased significantly as the horizontal offsets were reduced from 60 m to zero. With the comprehensive consideration of the stress field and TERs, a conservative offset of 60 m was ultimately adopted when developing the gateroads of the lower panel in the field. The field measurements indicated that coal bumps were avoided completely by employing the proposed design, and the maximum roof-to-floor and rib-to-rib convergences of the tailgate during retreat were only 360 mm and 576 mm, respectively.IntroductionCoal bumps – sudden, violent bursts of coal – pose a serious threat to the safe excavation of coal. Their occurrence depends on the properties of the surrounding rocks, stress field, and dynamic disturbance. The complexity of the mechanism of coal bumps is further enhanced in multiple-seam mining due to seam interaction. Multiple-seam mining is most frequently found in the coalfields in eastern China, such as Xuzhou, Xinwen, Zaozhuang, and Huainan. In the past, due to issues of availability, economics, and ignorance of the potential risk in multipleseam mining, coal seams in such conditions were mined without proper planning to account for seam interaction. Fortunately, studies published over the past three decades have raised awareness of the problems associated with multiple-seam mining, and indicated that the ground control issues induced by multiple-seam mining can be avoided and/or minimized with proper planning.A number of technical studies pertaining to the design of multiple-seam mines have been published. These studies can be divided into two groups based on their methodologies of design: empirical (Chekan and Listak, 1993; Haycocks and Zhou, 1990, Matetic et al.; 1987a, 1987b) and numerical approaches (Li et al., 2000; Maleki, 2007; Mark, 2007; Peng, 2007; Zipf, 2005). The majority of the extant studies on the interaction mechanisms in multiple-seam mining have focused on the load transfer during operation, resulting in the proposal of the pressure bulb theory (Forrest et al., 1987; Haycocks and Karmis, 1983; Peng, 2008; Peng and Chandra, 1980) and pressure arch theory (Holland, 1973; Oram and Ponder, 1997) to guide multiple-seam mine design. However, neither, of these theories can be used to evaluate the potential for coal bumps."

Jan 1, 2015

By D. F. Malan, R. P. Els

The limit equilibrium model, used in displacement discontinuity codes, is a popular method to simulate pillar failure. This paper investigates the use of physical modelling to calibrate this model. For the experiments, an artificial pillar material was prepared and cubes were poured using the standard 100 mm × 100 mm civil engineering concrete moulds. The friction angle between the cubes and the platens of the testing machine was varied by using soap and sandpaper. Different modes of failure were observed depending on the friction angle. Of interest is that significant loadshedding was recorded for some specimens which visually remained mostly intact. This highlights the difficulty of classifying pillars as failed or intact in underground stopes where spalling is observed. The laboratory models enabled a more precise calibration of the limit equilibrium model compared to previous attempts. Guidelines to assist with calibration of the model are given in the paper. The limit equilibrium model appears to be a useful approximation of the pillar failure as it could simulate the stress-strain behaviour of the laboratory models.

May 3, 2023

By M. Rhodes

The Sukari project, which is owned by Centamin Egypt Ltd, is located in southern Egypt, 770 km south of Cairo but close to the Red Sea. The project is the first new gold development in Egypt and was commissioned in the middle of 2009. In 2007, Centamin purchased the CIL plant from the Kori Kollo mine in Bolivia. This plant was originally designed to treat 6.5 Mtpa of oxide ore. The Sukari deposit contains an oxide zone close to surface with a thick zone of mixed oxide and sulphides below this. The sulphides contain relatively coarse pyrite and arsenopyrite with fine <10 µm gold inclusions. Eventually, the sulphide ore will be mined from underground. Metplant Engineering Pty Ltd, a subsidiary of Bateman Engineering Pty Ltd was contracted to design modifications and additions to the Kori Kollo plant to enable it to treat the Sukari ores. The plant was designed to treat the three ore types in stages. Throughput was set to 4 Mtpa, dueto Sukari ore being harder, at a head grade of 1.7 g/t to produce 200 000 oz of gold. The oxide circuit was based on the use of the Kori Kollo plant and the difference with mixed ore was that the oxide circuit would treat flotation tailings rather than ore. This circuit has a leach capacity of 26 000 m3 and residence time of 24 hrs The main feature of the upgraded mixed ore plant was the addition of a flotation circuit to produce a concentrate which would be reground and treated in a separate leach and elution circuit. Ore is crushed in a gyratory crusher and the comminution circuit uses a conventional SABC producing a product with a P80 of 150 microns. The throughput of 580 tph of oxide ore and 500tph of mixed ore was set to match the mills from Kori Kollo, with the addition of the pebble crusher to accommodate the more competent Sukari ore. The flotation circuit comprises a single rougher circuit to maximize recovery. The concentrate is thickened prior to regrinding which is carried out in a tower mill and two SMD mills operating in series. The final product, with a P80 of 12 microns, from the regrind circuit is leached in a CIL circuit with a total capacity of 2 550 m3. Gold is recovered through a conventional pressure Zadra circuit. Tailings from both circuits report to separate tailings thickeners and are pumped to a tailings storage facility. The circuit is designed to maximize the recovery of water. The project lies in one of the driest deserts in the world and a feature of the operation is the use of sea water from the Red Sea. This water is pumped 25 km from the coast.

Jan 1, 2009

By C. Musingwini, A. S. Nhleko, P. M. Muke

Open-pit mine planning includes the determination of a long-term open-pit mine production scheduling (OMPS) plan. The OMPS plan is generally a three-dimensional (3D) block extraction sequence that seeks to maximise the net present value (NPV) of future cash flows, while complying with technical and operational constraints. The OMPS problem is computationally complex because it involves the analysis of large datasets, while simultaneously incorporating both multiple hard and soft constraints. The OMPS problem has been solved using deterministic or exact approaches, heuristic, and metaheuristic models. When compared to heuristic and metaheuristic models, deterministic approaches tend to take much longer to solve the OMPS problem when the number of constraints increases. Therefore, this paper presents a metaheuristic model which utilises a genetic algorithm (GA) framework to solve the OMPS problem. The GA-based model was applied to the Newman1 and Zuck Small mining instances, which are publicly available from the online MineLib database. The NPVs for the OMPS plan generated using the GA-based model for the two case studies were compared to the best-known published MineLib solutions obtained using the TopoSort heuristic model at the time of this study. For the Newman1 instance the equivalent annual NPVs were approximately US$6.6 million for the GA-based solution and US$5.1 million for the TopoSort solution. For the Zuck Small mining instance, the equivalent annual NPVs were approximately US$99.8 million for the GA-based solution and US$102.5 mil for the TopoSort solution. These results show that the GA-based model produced comparable solutions to some of the best-known solutions, thus, indicating strong potential application of GA-based models to solve OMPS problems.

Sep 1, 2021

By Brian Wyatt, Neil Webb, Marcel Roche, John Thirkettle

Recent developments in survey techniques and measuring equipment now allow for an accurate assessment of external coating condition and cathodic protection performance. These developments build on 20 years of experience of using Direct Current Voltage Gradient (DCVG) and Close Interval Potential Survey (CIPS) methods. The techniques use the latest advances in measurement systems coupled to a bespoke data processing system. The paper describes tests and trial surveys carried out on a hydrocarbon transmission pipeline in West Africa during 2005. The survey works described and conclusions drawn are from the data collected. Of particular interest are the apparent capacitance effects which are thought to occur under disbonded coating and the characteristics that these may show on the integrated CIPS and recorded DCVG profiles. This paper was originally presented at the Cefracor conference in Aix, France, in June 2006 The pipeline was originally installed on a phased basis between 1989 and 1994. The external coatings were three layer polyethylene factory coating and shrink sleeve field joint coating. An impressed current cathodic protection system was installed. The pipeline has subsequently been affected by disbondment of the coatings. It was a primary objective of the trials to attempt to identify such affected areas. In addition to a technically detailed account of the survey works undertaken and the results obtained the authors will consider the practical and commercial aspects of these surveys with input that provides a perspective from the specifier, pipeline surveyor, pipeline operations personnel and the pipeline owner. It is intended that the data presented will provide greater awareness of the benefits and limitations of the techniques used and their role for both stand-alone interpretation and the integration of the survey information with other inspection methods used for external corrosion assessment. The application of the described techniques is well developed and proven to locate and characterise through?coating defects and to provide a full audit of cathodic protection status. However, the possibility of the techniques being able to indicate disbonded coating is unproven and further tests and trials are planned which may allow a greater understanding of the electrical characteristics which are believed to be associated with disbonded coatings which may or may not be filled with an electrolyte. Further work is currently planned in West Africa, South Africa and Scotland in order to improve the understanding of this technique and to determine if the reported indications do actually represent a method of locating disbonded coatings. Keywords: External Coating, Cathodic Protection, DCVG, CIPS, corrosion assessment.

Jan 1, 2006

By L. Thomas, D. Muteba, L. I. Nsenga, B. Mbao, G. Longo Banza

Owing to the high ore grades in the African Copperbelt and variable acid consumption, agitated leaching is common practice and is used more widely in Africa than in other regions. Two common challenges for agitated leach–solvent extraction circuits are higher presence of colloidal silica in the pregnant leach solution and elevated levels of total suspended solids. Both can negatively affect the physical and metallurgical performance of the solvent-extraction circuit, and lead to higher processing costs or reduced copper production. Operating in organic continuity is preferred to address such challenges, but is not always possible: additional treatment options may be advantageous. For this reason, Solvay recently introduced ACORGA® CR60LT, a new chemical additive to address these concerns. Continuous addition to the pregnant leach solution improves physical performance without negatively affecting Cu transfer or cathode quality. Results and benefits from commercial utilization of ACORGA® CR60LT at different operations in the Copperbelt are reviewed

Jan 1, 2023