Search Documents

By Richard J. Mainiero, Eric S. Weiss

This project investigates the behavior of blast waves from the detonation of high explosives in an underground mine. A series of explosive tests was conducted in the underground and surface facilities at the Bureau of Mines' Lake Lynn Laboratory to evaluate the potentially dangerous effects of blast waves produced by open shooting, blown out holes, or accidental detonations of explosives. Shots of C4 and TNT were fired at the dead end of a 6 ft high by 20ft wide entry, at the intersection of two entries, and on the surface. C4 and TNT were chosen for this research because they exhibit very consistent performance. Behavior of the blast wave was evaluated through recording of the pressure as a function of distance from the explosive detonation.

Jan 1, 1995

By J. Sigler

A series of small scale tests have been performed to establish the effect of powder factor and initiation timing on the grindability of rocks. The blasts were performed in high quality granite blocks, which were cut from stone prepared by dimensional stone quarry operations. Three different types of granite were tested. The charge configurations included detonating cord placed in five holes with water as a coupling medium or concentrated charges of equal mass, placed in the same number of holes, fully stemmed or air decked. The powder factor was varied from 0.4 to 1.2 kg/m3. Typically all charges were detonated simultaneously; however, in some experiments, detonation waves collided in the middle of each borehole and in others a small delay was used between charges. All fragments were collected and screened, and drop weight impact tests were performed on selected size fractions, using different impact energy, to calculate the resistance of the rock to impact breakage. The work index of some of the blasted samples was measured using a standard Bond mill arrangement. The experiments generally showed increased softening of the rock with powder factor, which appeared to be the dominant factor. Charge configuration as well as in-hole collisions of detonation waves affected the initial fragmentation but had little effect on the impact breakage of the samples.

Jan 1, 2008

By Leslie Taylor, Uli Leiste

In this paper, results from small scale testing conducted to determine pressure time profi les acting on a plate (taken to represent the bottom of a vehicle) at any given distance from the center of the plate will be presented. These results will be discussed in relation to visual observations of the upward moving sand.

Jan 1, 2008

By Daodu Opeyemi

This paper describes several damages of blasting operations on some case studies, analyzes causative factors, and emphasizes preventive measures. Due to several complaints from some host mining communities as a result of blasting operations; two quarries from Nigeria suburbs were visited for study. The blasting design parameters in the mining companies were examined. Also, the history and existing conclusion of the neighboring buildings were studied using structured questionnaire, personal contact and visual examination. From the study carried out, it was discovered that varying negative environmental and socio economic problems resulted from the effects of vibration and flyrock on the nearby agro mining communities. The consequences are not limited to distortion of landscape but also include extinction of some animals, poor agricultural productivity; such as damages to economic trees and reduction in the yield of crops, health problems as a result of shock resulting to psychological disturbances, communal conflicts, blast induced cracks of structures and sometimes total collapse of host agro mining buildings, thus indicating that most mines did not comply with the safety concept of the existing environmental laws and regulations. Based on the results of the study it was recommended that proper blast design of quarries/mines should be conducted and the compulsory use of seismograph will be crucial in developing predictions. Environmental impact assessment should always be conducted before, during and after each blasting operation. Other possible control of vibration, flyrock and airblast, are also discussed in the paper

Jan 1, 2009

By D T. Froedge

The state of Kentucky is making some changes in it's blasting program namely instituting a training program for blasters and instituting a new classification of blaster titled "Class A Kentucky Blaster". These changes will take place within the next year and are felt to be of great interest and benefit to those in the blasting industry.

Jan 1, 1978

By C W. "Mickey" Bradley

Thunder strikes terror in the hearts of man and has since the advent of time. We all fear the unknown; even the Greeks created a god, THOR, to be responsible for the thunder and rain. Thunder, by itself, can't hurt anyone; it is simply hot air moving very fast. Thunder, however, is caused by lightning and lightning is what we need to fear and rightfully so. Annually, lightning kills hundreds of Americans, injures another 2,000, damages or destroys approximately 30,000 structures, 1 starts thousands of forest fires and strikes mine properties over 100,000 times.

Jan 1, 1992

By Lazar Kricak, Zoran Teodorovis, Dragan Bogunovic

Scattering of delay interval around nominal value is an important issue in blasting practice. The scatter interval, as becomes wider, increases a probability of time delay overlapping adjacent blastholes. An excessive flyrock, ground vibrations, air blast and poor fragmentation are the symptoms for scattering related problems. Utilization of the short delays in the blastholes and longer delays on the surface are recommended solution to overcome mentioned problems. In contrast to global trends manifested through the application of electronic detonators and non-electric shock tube systems, revitalization of inexpensive electric detonators in combination with an accurate initiation system may be an acceptable solution. An extensive work was carried out at the Blasting Center Laboratory at the College of Mining and Geology, University of Belgrade, to develop a precise initiation system. As a result, Sequential Blasting Initiation System – Radio Frequency (SBIS-RF) was developed. It is expected that this system will increase blasting productivity, and reduce negative environmental impacts and total blasting costs.

Jan 1, 2008

By Anne Caroline Costacurta Polli, Jose Rojas Cáceres, Roberto Mahler de Morais, Thais Costa Silva

The technology and the knowledge about the behavior of explosives and detonation accessories allowed to create new products for different situations by the restrictions imposed by the market. In a Brazilian underground copper mine the restriction occurred in the use of high grammage Det Cord in the development heading blasts perimeter holes. Enaex Brazil has developed Densiex UG™ (Low-Density Bulk Emulsion), a water-resistant bulk gassing emulsion with a density ranging from 0.60 to 0.90 g/cm³ to replace the high grammage Det Cord in blasts. That product is pumped in the same Mobile Manufacturing Unit (MMU) as Enaex Brazil's standard underground (UG) bulk emulsion. This product has a Lower Velocity of Detonation (VOD), vibration, and detonation pressure, which contributes to a better finishing of the drift, lower impact in the support structures, and lower generation on unstable rocks in the perimeter of the drift. This case aims to summarize the results of the work on the application of the Low-Density Bulk Emulsion in perimeter holes in an underground development gallery at an underground copper mine in Brazil. During this work, 10 horizontal drift blasts were performed using the Low-Density Bulk Emulsion, which presented an average density of 0.64 g/cm³, increasing safety, a 25% reduction in overbreak, a 23% reduction in scaling time, elimination of rework, and a saving of $135,000 per year for this business partner that immediately implemented this new product in all blasts at this mine.

Jan 21, 2025

By William Hissem

When we look out on our business landscape today, the words higher, faster, fdwther come to mind. Compliance issues, business integration, increasing production and profitability demands are converging in an age old industry and giving it a new twist. Not that the rock changes, rather that as the variables of our business change, the resulting “cut-off grade in business” turns ore into rock or rock into ore. The trick is to emphasize the latter. As with the miners of yore, what was recovered from the business enterprise had a lot to do with tools and skill. So it is today. When the casual observer looks at drilling and blasting operations today, many see the same basic offering in terms of equipment types and process. Looks, however, can be deceiving. As with the aviation sector, a given machine might took similar to previous generations of equipment, but in fact is radically different in terms of power, efficiency, accuracy, and range. So it is with hydraulic top-hammer drills today.

Jan 1, 2000

By K. Hausmann, W. Whelchel

The properties of ethylene Ionomer resins for the inner layer of non-electric shock tubes will be discussed in detail, and opportunities for property enhancement will be pointed out. A stiffness program for prediction of shock tube stiffness, as determined by the stiffness of the individual layers, will be presented and discussed.

Jan 1, 2010

By N. Paley

An engineering project was undertaken at the Cominco Alaska Red Dog Mine to determine the extent that Semi-Autogenous Grinding (SAG) mill throughput could be increased by blasting differently. The Julius Kruttschnitt Mineral Research Center (JKMRC) blast fragmentation, jaw crusher, and SAG mill breakage models were used to relate changes in the blast design to the SAG mill performance. For optimum performance a SAG mill requires a particular size distribution; a number of large rocks to facilitate breakage by impact, as few as possible middle size rocks that become critical size, and the maximum fines which will pass quickly through an open-circuit mill. Physical constraints of drill and charging equipment size limit the extent that pattern geometry can be changed and the powder factor increased to maximize fines. However, JKMRC research had shown that it appeared possible to increase primary breakage by blasting to such an extent that SAG mill throughput could reach a plateau or even begin to decrease. Modeling was carried out on a range of blast pattern geometries and emulsion explosive blends to determine if a plateau existed and at what powder factor it would be reached. It was found that the relationship between powder factor and grinding throughput was nonlinear. Modeling was also used to compare the SAG mill throughput which could be expected from different emulsion explosive blends to determine which blends should be used in dry and wet holes to provide similar fragmentation. For heavy-ANFO mixtures, the highest modeled throughput was at a ratio of 30/70, with ratios on either side indicating lower throughput. For emulsion blends, the highest modeled throughput was at a ratio of 80/20; however, ratios from 80/20 to lOO/O were similar. Crusher product size distributions were obtained from belt cuts early in the analysis to confirm model predictions. At later stages, actual SAG mill throughput was compared to predicted. The economic benetit from the different blast designs was calculated by accounting for the reduction in recovery due to the higher throughput and the additional drilling and blasting costs. Increasing the powder factor by 150% from the 0.29kg/t {0.58lb/st] being used to 0.72kg/t { 1.44lb/st}, the maximum feasible with mine equipment, could provide a sign&ant net benefit of $3OWyr due to the increased concentrate production. However, because the relationship between throughput and recovery is affected by other factors which were not modeled, a more conservative approach was taken. The powder factor was instead increased by 50°h, providing 45% of the gain. This was possible because the relationship between powder factor and grinding throughput was nonlinear.

Jan 1, 2001

By Art Frye, Lee Pratt, Gaichang Zhao, Greg Newman

This paper will discuss the Wight Pit wall slash at the Mount Polley open-pit copper-gold mine that scavenged a high grade block of ore from two double-benches of the pit wall. The Wight Pit orebody, discovered in 2003, is located in the Northeast of the property with the southeast pit wall approximately 50m (165ft) from the edge of Polley Lake. In early 2009, the Wight Pit was nearing completion while an estimated 150,000 tonnes (165,000 tons) of ore averaging a grade of 1.4% copper remained just inside the southeast pit wall. The ore block started 24m (78ft) above the pit floor and extended up another 48m (157ft) with a 70o plane defining the back of the block.

Jan 1, 2011

By Julia Creasey, Natalie Hodgson, Claire Ward, Craig Davies, Helen Sarginson

"Emulsion explosive producers are attempting to lower the cost of emulsion production by using lowquality ammonium nitrate in emulsion formulations. Low quality ammonium nitrate contains additivessuch as anti-caking agents and crystal modifiers which contaminate the emulsions causing instability. This presents a need for an effective emulsifier that will maintain emulsion stability under thesechallenging conditions."

Jan 1, 2017

By Ronald Ticona

Generally, the drilling and blasting operation are managed independently to the processing plant outcomes. Therefore, the technical segmentation to determinate the ore drill and blast designs do not include processing plant rock properties such as Bond Work Index, Axb, Drop Weight Index or other. This work describes the case study of a copper mine in Peru, which, together with its strategic partner ORICA, have implemented projects focused on optimizing mine fragmentation. The year 2021, mine operation according to its mine plan would have a significantly increased SAG mill hardness, which would impact directly on copper concentrated production. An integrated strategy from mine to plant has become necessary to maintain the production levels.

Feb 6, 2023

By María Virginia Ramírez, Alejandro Alarcón, Alea Reyes

Reactive grounds (presence of FeS2, CuFeS2) can create hazards in a mine; misfires to premature deflagration or detonation of loaded blast holes. This occurs because some minerals can react to ANFObased explosives. Due to a high potential event that occurred in The Mine in 2013, The Mine and the Explosive Provider (“The Company”) are conducting a soil characterization of the areas containing reactive sulfides. This study was planned along with The Mine and it is being developed by a multidisciplinary team.

Jan 1, 2018

By G. Walsh, L. Wolkovitch, A. Savage, V. Romero, T. Zimmerly, G. Imahara, J. Hyneman, K. Byron, D Tapster, S. Belleci, J. Metzger, M. Stanley

Testing was conducted at the Energetic Materials Research and Testing Center for the MythBusters on three separate occasions. This testing included (1) an experiment designed to create diamond from graphite using the shock and pressure of a detonation, (2) the flattening of a car using a steel plate driven by a rocket sled, and (3) the bifurcation of a car also using a rocket sled. All tests were successful; diamond was produced following the detonation of ANFO, and extracted from a graphite / cobalt matrix. A plate was accelerated to 646 mph (1040 km/hr) using a two-stage sled system loaded with 5” (12.7 cm) high velocity aircraft rockets (HVAR) into a car, which was subsequently demolished. Finally, a steel wedge was pushed to 541 mph (871 km/hr) by a one stage sled using HVAR rockets, and was able to cleanly cut a target car in half.

Jan 1, 2010

By Robert Hopler

On June 13, 1912, the final decree of dissolution of the DuPont explosives trust was handed down, and the resulting new companies began operating at the beginning of the new year. The property assets granted to (or retained by) the companies were as follows:

Jan 1, 2014

By P. Lozada

The objective currently demanded from controlled blasting techniques is to minimize damage to the remaining rock mass while protecting the integrity of mine walls and ensuring the quality of the fragmented material for easier extraction. Finding this balance represents one of the three main challenges faced by large open-pit mines. They must achieve mine stability by complying with slope designs while also maintaining good results in terms of fragmentation and equipment productivity. The main constraints are related to unfavorable geological conditions, water presence, limited drilling diameters and available explosive products, as well as managing drilling times and blast scheduling, among others. For slope control, in addition to presplitting, blasting designs generally include buffered rows, drilled with smaller diameters, and loaded with fewer kilograms of explosives than production holes. The objective is to reduce the powder factor (kg/t) to minimize the energetic influence on the walls and attenuate damage. However, this often requires using very short charge lengths compared to the bench height (one-third or less) and reducing the pattern geometry, which increases the number of holes per ton and drilling costs. This traditional technique of reducing powder factor in the buffered rows has the main limitation of not being able to distribute the explosive energy throughout the entire column, leading to fragmentation issues mainly in the steaming area. Measurements conducted by Orica in their operations indicate at least a 30% increase in P80 particle size in the buffer zone associated with this condition. To improve energy distribution, techniques such as decking, or vertically decoupled charges can be employed. However, these techniques cannot be applied under wet conditions, and strict control over implementation quality is required to avoid deviations, which increases loading operational times and resource required. In this sense, the use of less energetic and lower-density explosives is a better alternative. On one hand, they allow for complete charge columns in the buffered rows, ensuring homogeneous fragmentation, and on the other hand, they reduce the energetic influence on the slopes, significantly decreasing vibration levels. With less energy per kilogram of explosive (MJ/kg) and less charge per linear meter (kg/m), it becomes possible to handle higher specific charges and longer explosive columns, providing flexibility in drilling and loading design options without compromising slope stability.

Jan 1, 2024

By Jeffrey W. Lin, Jonathan D. Abbott, Patrick R. Bowden, Tyson J. Plitt

Pentolite is a class of high explosives containing trinitrotoluene (TNT) and pentaerythritol tetranitrate (PETN) with PETN content typically ranging from 40 to 60 wt%. Manufacture involves melting TNT, 80 °C, followed by addition of PETN and trace ingredients to form a homogeneous mixture. Once a mix is ready to be poured, several factors can influence the behavior of the finished product including how long the mix has been at temperature and cooling rate. After the manufacturing process has been completed, storage conditions combined with manufacturing conditions may cause physical changes. Two such changes explored were exudation, liquid exuding from solid boosters, and ratchet growth, irreversible volumetric expansion. Exudation is principally caused by excess water in the process. Ratchet growth is a common phenomenon of nitroaromatic compounds such as TNT where time and temperature fluctuations can cause materials to increase volume, simultaneously decreasing density. Although neither phenomenon affects common attributes such as sensitivity, performance, and shelf-life, both can cause issues in storage and handling. In this study pentolite was cast into various forms under different manufacturing conditions and evaluated over several months of controlled storage conditions including ambient, temperature cycling and elevated isothermal. Subjective and objective measurements were made throughout the evaluation period with the aim to determine the preferred storage methodology.

Jan 21, 2025

By Alejandro Ferrada Vergara, María Jesús Barros Godoy

The need for a basic method for selecting explosives based on rock mass or intact rock properties for mining and construction arises from the limited consideration given to these factors when choosing among products and also an implicit overestimation of the explosive power to fragment the rock. This study highlights the importance of evaluating different properties such as rock strength, deformation, fracturing, detonation velocity and energy release when selecting explosives. The concept of characteristic impedance, which considers rock strength against shock waves generated by explosive detonation, is introduced. Understanding this concept is crucial for assessing explosive behavior according to various rock types. The study concludes with a practical guide table that categorizes rock properties and provides recommendations for selecting explosives based on rock mass and rock properties. However, it is important to consider other relevant factors, such as the presence of water or nearby instabilities, which can influence the final choice of explosives.

Jan 21, 2025