Search Documents

By Jia Ma, Lu-De Qiang, Zhi-Chao Liu, Chun-Feng Li, Guang Li, Bao-Bin Tang

"At present, research on the surface chemical properties of uranium minerals is very scanty, which restricts the research progress of uranium ore flotation process research. The research aimed at exploring the surface characteristics of two common uranium minerals and providing basis for flotation process to enrich uranium minerals in ore. This paper selected pitchblende and uraninite as the object of study, which are widely distributed in uranium deposits. We chose out the pure minerals of pitchblende and uraninite from different ores collected from different uranium deposits. By means of Zeta potential test and X-ray photoelectron spectroscopy (XPS) test, a preliminary study on surface characteristics of the pure minerals of pitchblende and uraninite was conducted. And the significance of the change of Zeta potential, the elements composition and valence state on the minerals surface for flotation was discussed. The research shows that, the Zeta potentials of pitchblende and uraninite in pure water are negative mainly when the pH value varies from 2 to 11, which maybe a result of the difference of ionization capacity between two kinds of oxy-compounds on the surface of minerals. On the surface of pitchblende and uraninite, the metal elements are mainly U, Th and Pb. U is mainly in the form of UO2, Th is mainly in the form of ThO2, and Pb is mainly in the form of Pb and PbO. Based on the surface characteristics of pitchblende and uraninite, we can select process and reagents appropriately in uranium ore flotation.INTRODUCTION Globally, the major challenges associated with exploitation of low grade ores are about finding economically feasible processes for reducing the mass of gangue minerals (Filippov et al., 2012). Among the beneficiation technologies of low grade uranium ores with complex minerals assemblage, flotation is the common process which is used to reduce production cost and eliminate the acid-consuming minerals (Li et al., 2016; Liu et al., 2015)."

Jan 1, 2018

The present work aimed to verify the possibility of using froth flotation to separate the constitu-ent minerals of an alaskite rock waste having as the main minerals quartz and feldspar. Three stages of tests have been carried through. In the first stage was used an amphoteric collector for flotation, diaminedioleate, at pH 2 and, after analyzing the final products, a very poor selectivity was ob-served. During the second stage of tests, different collectors that are normally used for feldspar flo-tation as amines, sulfonates and soybean oil were employed. Once more, it was not possible to reach reasonably selective results. In the third stage, a salt of etheramine was used for collecting the feldspar and hydrofluoric acid was utilized for controlling the pH. A simulation of three flotation steps (rougher, cleaner and recleaner) permitted to attain a good selectivity in the flotation process. A concentrate with a silica content of 96.6% was obtained. The low concentrate content of alkalis totalizing 0.52% and a feldspar recovery of 96.5% to the tailings, represented by the high content of Na, K, and Al2O3 in the tailings, demonstrated that the concentrate was made up mostly of quartz.

Jan 1, 2014

By I. Nishkov, I. Grigorova, M. Ranchev, S. Dzhamyarov

"Chelopech concentrator (part of Dundee Precious Metals) is located in central-western Bulgaria. The current process plant utilizes conventional primary crushing and SAG mill grinding, copper and pyrite rougher and cleaner flotation stages to produce a marketable gold-rich copper and pyrite concentrates. As in the most processing plants, the pyrite depression is carried out alkaline media using lime. The subsequent activation of pyrite mineral is achieved by adding sulfuric acid, which has an adverse effect on the flotation equipment. Therefore, a series of laboratory flotation experiment for activation of lime depressed pyrite by ammonium salts, such as ammonium chloride (NH4Cl), ammonium sulfate (NH4)2SO4 and ammonium bicarbonate (NH4HCO3), have been conducted. The obtained results showed that ammonium bicarbonate proved to be the most appropriate reagent choice for pyrite mineral activation. These results are confirmed by X-ray photoelectron spectroscopy (XPS), performed to determine the surface chemistry of pyrite in its natural state, after lime treatment and subsequent treatment by NH4HCO3. The registered XPS spectra indicate that the hydrophilic phases on the pyrite surface could be efficiently removed by using the ammonium salt NH4HCO3. The industrial use of NH4HCO3 as an activator of lime-depressed pyrite is a possible alternative for sulfuric acid replacement as a most widely used pyrite activator. Flotation experiments with addition of 200, 400, 600 and 800 g/t from each of the studied ammonium salts have been conducted. Furthermore, the impact of the flotation pulp pH within the scope of 9.00 – 10.50 was also investigated. The obtained results from the laboratory flotation experiments, showed that the pyrite activation with ammonium bicarbonate is an excellent possibility for replacing the sulfuric acid as main pyrite activator reagent, in order to eliminate the gypsum accumulation during the flotation of pyrite in Chelopech concentrator.INTRODUCTION The Chelopech deposit, located about 60 km east of Sofia is one of the largest Cu-Au deposits in Europe. The ore have complicated mineralogical and chemical composition. The main ore minerals are represented by pyrite, enargite (luzonite), tennantite, chalcopyrite and bornite. The average copper content of the mined ore is about 1.1 % and the gold content is about 4.0 g/t."

Jan 1, 2018

By N. R. Mandre

In the present work an attempt has been made to study beneficiation of low-grade iron ore associated with manganese clay by selective flocculation. The representative samples obtained for this purpose were initially subjected to chemical and mineralogical studies. The chemical analyses indicated 42.56 % Fe, 6.25% Mn, 8.72 % SiO2 and 13.60 % Al2O3 in the representative sample. The mineralogical analyses carried out under optical microscope showed that the ore mineral predominantly comprised of iron oxides and hydroxides along with manganese and silicate as gangue minerals. Prior to the beneficiation studies, the samples were subjected to settling tests. These tests were carried out by using poly acrylic acid (paa), poly acryl amide (pam) and guar gum (gg) as the flocculants. From these studies it was observed that settling rate of particles increases with increase in pH and a maximum settling rate of 0.23 cm/secwas obtained at pH 9 in presence of poly acryl amide. Further, the samples were subjected to selective flocculation studies using above-mentioned reagents. From these studies better results were obtained in the experiments carried out with poly acryl amide as the flocculant. Thus, it was possible to upgrade the iron content from 42.5 to 53%, with a recovery of 92%. However, 51% Fe with recovery of 87% and 50% Fe with recovery of 94 % was obtained using poly acrylic acid and guar gum respectively.

Sep 1, 2012

By J. Temuujin

Mongolia has some of the world?s largest coal reserves with an estimated total coal reserve of over 150 billion tonnes. At present, over 90% of Mongolian electricity is produced by combined heat and thermal power stations. The main coal deposits used for Central power system's power stations are Baganuur, Shivee-ovoo lignite type coal and Shariin gol bituminous coal. In Mongolia almost 600,000 tonnes of coal combustion by-products are disposed of in waste ponds. In this research, we have thoroughly characterized Mongolian coal combustion by-products including fly ashes sourced directly from thermal power stations and ash retrieved from ponds. It was determined that fly ashes generated from Baganuur and Shivee-ovoo coal deposits are class C, while ash from Shariin gol coal is class F (according the ASTM C618). All ash products were characterized by chemical, mineralogical, granulometrical, porosity, FE-SEM and radiation methods. Fly ashes sourced directly from power stations were found to be more suitable for manufacture of geopolymers for building materials application and zeolite synthesis than ashes retrieved from ash ponds. The adsorption and porous properties of zeolitic compounds were measured and found to be suitable for adsorption of Cr6+ from simulated tannery waste water. Keywords: coal, coal combustion by products, synthesis, geopolymers, zeolitic compound

Sep 1, 2012

By N. Johnson, J. Quinteros

With the general trend across all commodities towards the treatment of lower grade ores, it is becoming increasingly important to develop efficient protocols for comprehensive mineralogical characterisation to allow the development of the most appropriate strategies for processing an ore. In the case of silver, there are more than 200 known silver bearing minerals which can make it challenging to identify them. Knowledge of the deportment of silver within an ore is one of the factors used to determine an appropriate processing strategy. Automated SEM-based tools are commonly used for mineralogical characterisation but the low-grade together with the large number of minerals that are potential hosts for silver means that often, complementary analytical tools must be used in order to properly account for the silver. The work presented in this paper is a demonstration of the approach that should be taken when identifying the deportment of silver in complex ores. Three complex, low-grade silver ores were characterised using the approach. The insights from the mineralogical characterisation were then used to inform the metallurgical testing that was undertaken. The results from the batch flotation testing clearly demonstrate the importance of understanding the mineralogy in order to select the most appropriate metallurgical processes.

Jan 1, 2014

By Deirdre Bradshaw, Cornelius Vos

"The detailed understanding of the variability in process performance parameters within an ore body forms a key aspect of ensuring that proper decisions are made with regards to the economic viability of that ore body. To gain this understanding, various tools have been developed over the years, of which the batch flotation test is the most well-known and applied technique for investigating the flotation separation of ores. In this paper, the Julius Kruttschnitt Mineral Separability Indicator (JKMSI) is put forward as a small-scale test, suitable for the characterization of the flotation separability of copper porphyry ores. It is demonstrated that the JKMSI can be a complementary technique to the batch flotation test, with the capability to further improve the knowledge of ore body variability. The response from this test has been shown to be sensitive to particle size and modal mineralogy, providing a critical link between flotation and upstream comminution activities. The trade-off between the fineness of grind and the recovery target can thus be evaluated to determine the minimum energy application required for optimal separation economics. The test is designed to utilize small sample quantities of various sizes, providing an opportunity to increase our understanding of ore variability through increased tests. This complements our ore body knowledge and combining this with efforts in comminution (Powell, 2013) provides a platform for extending the concept of flexible circuit design."

Jan 1, 2014

By Skinner. W.

"Introducing cutting-edge development work, which aims to simplify mineral processing flow-sheets, reduce costs and address environmental issues. Over the past four years Innovative Mineral Processing Technologies Pty. Ltd (IMPTEC) Australia have developed a Super-fine Crusher and a Planar Magnetic Separator which offer low cost, wet or dry alternatives to conventional grinding and conventional magnetic separation. Each of these machines has been successfully trialed at pilot scale and are now in the process of transitioning to commercial scale. This paper reports on the progress made in each of these fields. The potential scope for application of super-fine crushing technology as an alternative to grinding is potentially expansive and could include beneficiation of metalliferous ores, precious metal ore processing, hydrometallurgical processing, industrial minerals and coal processing, plastic fillers and ceramics processing as well as processing of cementitious slags and fly-ash. IMPTEC have recently achieved outstanding results at pilot scale with a dry combination of super-fine crushing and planar magnetic separation, which offers an alternative to the wet processing of magnetic iron ores. The dry combination has set new laboratory performance benchmarks when compared with the industry standard wet Davis Tube Tester. The test results have also established a strong evidence base showing that super-fine crushing achieves liberation of value minerals at coarser sizes when compared with grinding. The dry combination of super-fine crushing and planar magnetic separation also addresses environmental issues and completely eliminates grinding. An IMPTEC super-fine crusher is currently undergoing commercial trials, generating ultra-fine products from granulated lead blast furnace slag for use as cement substitutes. The performance of the super-fine crusher on this extreme duty highlights the potential benefits of super-fine crushing over the wide range of industries and applications where conventional grinding is employed.INTRODUCTION Present day mineral processing practices can become anchored in convention, where, inefficient methodologies are recognized and accepted as “best practice” or “industry standard”. Motivated by this challenge, IMPTEC has undertaken the development of radically different and improved methodologies in the fields of fine comminution and magnetic separation. Whilst, crushing is much less energy intensive and generally less capital and maintenance intensive than grinding, the technology has stalled due to the lack of crushing devices, which have the capacity to adapt to fine and ultra-fine duties. Grinding practice advances have been achieved through major increases in machine size and power. However, these advances are also accompanied by major escalations in capital, operating and maintenance costs. The economics of this strategy has become increasingly questionable. A typical example is the viability of low-grade magnetite beneficiation, which can hinge largely on the cost of grinding to fine and ultra-fine liberation sizes."

Jan 1, 2018

By P. Romm

The German Kupferschiefer (copper shale) mining history reaches back over 800 years with its last active mines being shut down in 1990. Increasing metal demands and potential thread of future supply shortages led to the initiation of new exploration programs including feasibility studies for the Spremberg deposit as well as Federal Ministry of Education and Research (BMBF) funded research investigations of Kupferschiefer Waste Dump treatment in the Mansfelder region. This article describes the sensor based sorting results of coarse Kupferschiefer via Near Infrared (NIR) Sorting, being conducted by the department of mineral processing (AMR) in Aachen, Germany. It provides information about the necessity of presorting of the different ore types prior to flotation and puts the NIR Sorting results into context with conventional Kupferschiefer processing. Keywords: NIR sorting, kupferschiefer, sensor based sorting, preconcentration

Sep 1, 2012

There are interactions between different minerals from the same ore, minerals and grinding media, and the electrochemical conditions present in the system. Grinding in steel rod and ball mills is a common practice in minerals processing. It is accepted, that the electrochemical interactions between the grinding media and minerals in a grinding mill, influence the corrosive wear of balls/rods and the surface properties of the ground minerals. A complex massive sulphide, Cu-Zn, TAKNAR, Iran, was used for all the experiments. The aim of this study was to investigate the effect of grinding media (dry or wet) on the pulp chemistry and recovery of Cu and Zn in bulk concentrate. 1100 g of ore samples were milled, and mill products with d80=85 and 75 micron in wet and dry grinding methods were produced. Rougher bulk flotation experiments were performed with 550g ore samples, at 30% solids. SIPX in conjunction with Aero238 in 1:2 ratio (48 g/t), was used as mixed collector system, and copper sulphate (200g/t) and MIBC (20 g/t) were employed as sphalerite activator and frother. Lime and High purity Oxygen gas were used for adjusting pH at 8.5 and aeration. The results showed that, more positive pulp potentials were measured when the feed had been ground in a dry environment, and the difference in pulp potentials between the dry and wet ground feed was approximately 250 mV after the grinding stage. In dry grinding method, the recovery of Cu and Zn increased approximately 5 and 10%, respectively. In addition, in dry ground samples, the volume of middling and coarse particles (+100 micron) were more and Dry ground flotation feed had better agreed with using a mixture of collectors. After using copper sulphate, pulp potential increased about 50 mV in dry and 75 mV in wet grinding methods. Keywords: grinding media, pulp potential, Cu-Zn massive sulphide, bulk flotation

Sep 1, 2012

By D. W. Feng

Thiosulfate leaching has been considered as the most promising alternative to cyanidation for the recovery of gold from ores. The chemistry of the ammonia-thiosulfate-copper system is complicated due to the simultaneous presence of complexing ligands such as ammonia and thiosulfate, the Cu(II)-CU(I) redox couple and the stability of thiosulfate in solution. However, acceptable gold leaching rates can be achieved by maintaining suitable concentrations of thiosulfate, ammonia, cop-per and oxygen in the leach solution. The leaching of gold in thiosulfate solution is an electrochemical reaction involving the oxidation of gold to gold thiosulfate and the reduction of Cu(II) to Cu(I). Previous studies have shown that the reaction rate of gold was much higher in the presence of am-monia thiosulfate than corresponding sodium thiosulfate. This indicates that cations may affect the anodic oxidation of gold in thiosulfate solution. The present study utilises electrochemical tech-niques to study the anodic oxidation of gold in thiosulfate medium in the presence of the different alkali metal and alkaline earth metal ions. It has been shown that the presence of the heavier cations such as potassium, calcium, and caesium enhance the oxidation of gold in thiosulfate solution. Leaching tests also indicated the improved recovery of gold from a sulfide ore with the addition of heavier cations. XPS results demonstrated that the binding energy for gold shifted to lower values in the presence of the heavier cations, indicating the ready formation of ion-pair with gold thiosulfate at the gold surface during adsorption.

Jan 1, 2014

By A. Prokopiev

The biological stage of reclamation is the third final stage in remediation the damaged mining terrains, which is carried out following the completion of the mining technical stage. The biological stage of reclamation is carried out through restoration of the vegetation layer. The biological reclamation includes all activities related to the introduction into the terrain of vegetation, microorganisms, insects, and animals, with the acceleration of the succession and creating conditions for a sustainable ecosystem close to the natural one. It comprises of all anti erosion and other activities such as the preparation of the land for growing agricultural crops, sowing grass seeds, planting seedlings, amelioration of the soil and further care for the vegetation until its final place on the land. Mineral and organic-mineral ameliorants for biological reclamation were studied. The basic mineral ameliorant is Bulgarian natural zeolites. The zeolitic-rich tuff samples provided from Golobradovo deposit was characterized by their chemical and mineralogical composition and ion exchange properties and X ray analysis. The average content of clinoptilolite was found to be more than 80%. The materials had ion exchange capacity (NH4+) varying from 100 to 110 meq/100g. Chemical modifications of natural clinoptilolites were made in order to form active phases of nitrogen, phosphorus, potassium, and microelements. Slow-acting mineral ameliorant was developed. Organic-zeolite substrate for biological reclamation was developed. This new product is a mechanical mixture of organo-matter and modified zeolites. Agro-chemical parameters of new ameliorants were determined. The substrates including studied overburden dump soil and mineral or organo-mineral ameliorants are produced. The grass growth test was performed. Keywords: biological reclamation, ameliorants, damaged mining terrains

Sep 1, 2012

By N. N. Ngoepe

Positron Emission particle tracking (PEPT), which makes use of a radioactively labeled tracer particle, a positron camera and a tracking algorithm has been shown to be a viable method for studying flow properties in both the pulp and froth phases of flotation cells. Detailed velocity measurements of 300-400 µm glass beads were extracted to assess turbulence from velocity fluctuations in a micro flotation cell. The effects of particle speed and orientation at the instant of attachment events were studied. A minimum speed of 0.16 m/s was needed for a collision to lead to attachment. The most attachment events happen when the particle is directly in line with the inlet tube at 90o.

Sep 1, 2012

By G. K. Palshikar

Mining operations offer many opportunities for the use of IT and communication technologies to improve automation and thereby deliver higher levels of productivity, cost, quality and safety. In this paper, we discuss a particular application, namely, building a fully automated train control and operation system within a mining area. We first outline the basic architecture and functionality of such a system and then present a real-life case study where the railway system within a remote iron ore mine in Canada was converted to a fully automated train operation system. This hard real-time safety-critical system required the use of advanced technologies such as embedded systems (e.g., on-board train controller), radio communications, formal methods, optimal scheduling, and extensive simulations. We focus on the design aspects for maintaining the system in safe states.

Sep 1, 2012

During incineration of municipal solid waste (MSW), some heavy metals and other environmentally harmful elements are liberated into bottom ash. The stricter environmental regulations require a higher immobilization efficiency of the ash before its safe disposal and application. Vitrification is one of the promising options, and has the advantages of high destruction efficiency of organics, high immobilization of heavy metals, and large volume reduction. The main components of the vitrified slag are SiO2, CaO, Al2O3, Fe2O3, Na2O and MgO, and the compositions have direct effect on the glass formation during vitrification, and further on the physical and mechanical properties of the slag. To provide essential data for the utilization of bottom ash as vitrified slag, the phase relations and thermodynamic properties of the oxide system need to be systematically investigated. In the present study, the liquidus temperature of the typical vitrified bottom ash slag was determined by using differential scanning calorimetry (DSC) measurement. High temperature equilibrium experiments were conducted to investigate the phase relations of the sub oxide system of CaO-SiO2-Na2O by means of Scanning Electron Microscopy (SEM), Electron Microprobe Analysis (EMPA) and X-ray Diffraction (XRD). The results show that the melting temperature of the vitrified bottom ash is around 930°C. In the CaO-SiO2-Na2O system with less than 50 mol% SiO2, the liquidus temperature de-creases with increasing amounts of Na2O along the tie-line of Na2O-Ca3Si2O7. Two compounds Na2Ca3Si2O8 and Na4Ca8Si5O20 are identified in the oxide system.

Jan 1, 2014

By N. A. Dementyeva

To improve gold recovery from preg-robbing carbonaceous ores a technology including gravity, flotation, recleaning of the flotation concentrate, intensive cyanidation of the gravity concentrate and carbon-in-leach (CIL) process for intensive cyanidation tailings and the recleaned concentrate was developed. The final flotation tailings are shipped to tailings disposal. Total gold recovery by the proposed technology from the ore with the head grade of 0.8 g/t was 83.9%. The gold loading onto the activated carbon from CIL process was 6.5 g/kg.

Jan 1, 2014

By R. Singh

The paper presents the results of characterization and beneficiation studies carried out on a lean grade tungsten ore sample from Degana, India. Basically, three different routes, involving gravity separation, magnetic separation, and froth flotation were studied for concentration of the sample by physical and physico-chemical methods. Considering the low recovery by physical methods, efforts were put in to produce a tungsten concentrate by physical methods suitable for subsequent hydrometallurgical recovery of tungsten as ammonium para-tungstate. This strategy proved quite helpful in minimizing the losses of tungsten in tailings. Based upon these studies a novel integrated technological process flow-sheet was developed for the exploitation of lean grade tungsten ore deposit of Degana, India. Keywords: lean tungsten ore, characterization, beneficiation, gravity and magnetic separation, hydrometallurgical extraction, integrated process route

Sep 1, 2012

By P. Raghavan1

Reverse froth flotation experiments were carried out in the laboratory using two different types of kaolins for the separation and removal of coloring titanoferrous impurities from cryo-filtered clay after subjecting to high shear pre-treatment. This high shear pre-treatment consists of high shear agitation of a high solids clay slurry with the dispersant (high shear dispersion, HSD) followed by high shear agitation with the collector (high shear conditioning, HSC). After this pretreatment, the slurry is diluted and reverse flotation is carried out. One sample is from, Gujarat, India (Mamuara clay, ?MC?) while the 2nd sample is from Amberg, Germany (AKW clay, ?AC?). While MC consisted of 89% particles below 2µm and analyzed 1.06% of TiO2 and 0.29% Fe2O3 and measured a brightness of 83.4 %ISO, the corresponding values for AC are 67% below 2µm, 0.3% of TiO2? 0.49% Fe2O3 and 83.4 %ISO. The flotation performance is found to be greatly influenced by the conditions of high shear treatment. Important variables are HSD intensity (rpm), HSD time, HSC intensity (rpm), HSC time, HSD/HSC time ratio, ?HSD+HSC? total time etc. Higher shear intensities favor both the impurity liberation and collection. For both clays, it could be shown that impurity removal increases as total pretreatment time (?HSD +HSC? total time) increases up to a certain limit. For MC, the HSD time was only half or less than that of HSC time, while for AC, HSD time is at least twice (or more) than HSC time which is just an opposite manifestation. This is believed to be due to the striking differences between these two clays. Most importantly, the shear frequency is found more influential than the shear rate for the overall flotation performance for both clays. Interestingly, at high shear frequencies, i.e., when a stirrer with more number of teeth on the rotor is used, the ?HSD+HSC? total time is greatly reduced. Again, increased shear frequency helps to reduce flotation time and significantly improves flotation performance. At optimum conditions, product titania reduced to 0.35% for MC whereas the same reduced to 0.13% for AC. The product of flotation of MC measured 85%ISO brightness while that of AC measured84.6%ISO thus enhancing the value of the final product. It could also be established that the high shear pre-treatment shows better flotation performance than that due to collector dosage. Keywords: high shear dispersion, high shear conditioning, titanoferrous impurities, shear rate, shear frequency, brightness, clay recovery, Mamuara clay, AKW clay

Sep 1, 2012

By E. Guerrini, M. Maccagni, J. Nielsen

"The solution for the treatment of the EAFD has not yet been fully achieved. Some of this dust has still not found an appropriate final destination. Large consortium treatment plants are quite expensive both in terms of investment and operating cost. Meanwhile, the tolling expenses for steel production companies are becoming very important, causing them to look for alternatives. Some steel plants are looking to close their production loop by internal treatment of their dust. Some years ago, Engitec began studying the coupling of the EZINEX® Process, an ammonium chloride electrolysis to recover the zinc contained in the EAFD, with the INDUTEC® Process, a pyro process based on an induction furnace that can convert EAFD into a C.Z.O. similar to the Waelz oxide. The combination of these two processes provides an alternative to the existing treatment options and is particularly interesting for relatively small capacities. In this paper, we would like to give the latest update about these two processes and their possible integration INTRODUCTION Zinc is contained in numerous wastes and secondary raw materials that can be thought of as high zinc concentrate mines. This is a very interesting source of Zn that is typically easily exploitable. Unfortunately, only a portion of these materials are currently processed to recover the metal value, while stabilized or unstabilized landfilling is often the final destination. Pyrometallurgical processes are mainly used to convert the zinc into crude zinc oxide (CZO). The various processes are very similar and characterized by the fact that the zinc bearing materials are usually submitted to a thermal treatment [1] in which the zinc is reduced, vaporized and re-oxidized producing CZO. This material not only contains zinc oxide, but also relatively high concentrations of heavy metals. Many potential CZO sources, such as electric arc furnace dust (EAF), galvanizing ashes, brass foundry and converters fumes also contain chlorides, fluorides and alkali metals that will transfer to the CZO. The classic example is the Waelz oxide [2]. This CZO is an intermediate product that must be transformed into zinc salts or zinc metal. Until now, the conversion to zinc metal is done through two main processes: the sulphate leaching and electrowinning system and the Imperial Smelting Process (ISP). ISP is facing a crisis for technical and economic reasons that has led to the closing of most of the existing plants. In any case, before being fed to one of these two processes, the CZO must be treated to eliminate or reduce some of the contained impurities. In particular, the halides are most harmful to these processes."

Jan 1, 2018

By E. Guerrini, M. Maccagni, J. Nielsen

"The solution for the treatment of the EAFD has not yet been fully achieved. Some of this dust has still not found an appropriate final destination. Large consortium treatment plants are quite expensive both in terms of investment and operating cost. Meanwhile, the tolling expenses for steel production companies are becoming very important, causing them to look for alternatives. Some steel plants are looking to close their production loop by internal treatment of their dust. Some years ago, Engitec began studying the coupling of the EZINEX® Process, an ammonium chloride electrolysis to recover the zinc contained in the EAFD, with the INDUTEC® Process, a pyro process based on an induction furnace that can convert EAFD into a C.Z.O. similar to the Waelz oxide. The combination of these two processes provides an alternative to the existing treatment options and is particularly interesting for relatively small capacities. In this paper, we would like to give the latest update about these two processes and their possible integration INTRODUCTION Zinc is contained in numerous wastes and secondary raw materials that can be thought of as high zinc concentrate mines. This is a very interesting source of Zn that is typically easily exploitable. Unfortunately, only a portion of these materials are currently processed to recover the metal value, while stabilized or unstabilized landfilling is often the final destination. Pyrometallurgical processes are mainly used to convert the zinc into crude zinc oxide (CZO). The various processes are very similar and characterized by the fact that the zinc bearing materials are usually submitted to a thermal treatment [1] in which the zinc is reduced, vaporized and re-oxidized producing CZO. This material not only contains zinc oxide, but also relatively high concentrations of heavy metals. Many potential CZO sources, such as electric arc furnace dust (EAF), galvanizing ashes, brass foundry and converters fumes also contain chlorides, fluorides and alkali metals that will transfer to the CZO. The classic example is the Waelz oxide [2]. This CZO is an intermediate product that must be transformed into zinc salts or zinc metal. Until now, the conversion to zinc metal is done through two main processes: the sulphate leaching and electrowinning system and the Imperial Smelting Process (ISP). ISP is facing a crisis for technical and economic reasons that has led to the closing of most of the existing plants. In any case, before being fed to one of these two processes, the CZO must be treated to eliminate or reduce some of the contained impurities. In particular, the halides are most harmful to these processes."

Jan 1, 2018