Search Documents

By Bengt H. Fellenius

The design of pile foundations is much more commonly verified by means of a full-scale test, than is the design of other foundation units. The reason is not that our knowledge of pile behavior is more uncertain than our knowledge of other foundation types making the verification necessary, but more that the loads in a structure are more concentrated to single foundations in a structure founded on piles as opposed to structures on footings or mats. Therefore, should a pile cap fail or move, the adverse consequence of this is often drastic, as the piled structure has little freedom to transfer its need for support to other foundation units. Consequently, it becomes important to assure the design of piled foundations. In many, maybe in most instances, the static pile loading test is routine and geared toward determining an at least capacity, only. However, in these times there is an ever increasing liability of the professional, demands for increased economy of the foundation, and frequent lack of the involvement in the test of the experienced old-timer exercising good judgment. Furthermore, modern pile design is leaving the single, simple concept of capacity and requires more information from the test to assist in determining aspects of long-term behavior and settlement. Therefore, even the straight forward, routine static loading test requires improved planning, execution, and analysis.

Jan 1, 1990

By Abhijit Saha

"The stone columns improve the performance of foundations on soft and loose soil due to the ability of composite ground to sustain increased structural loads under reduced settlements. The interaction between the two basic elements: the ambient subsoil and installed column, present a complexity of behaviour, both in terms of applied stresses and resulting strains. Moreover, as the same is provided in-group in a regular array beneath foundations, the performance of an individual column is likely to be influenced by the presence of neighbouring columns. The present paper addresses this very issue. Analysis of reported field hydro-test data of large diameter oil storage tanks in soft ground in reference to some existing theories led to the development of the stone-column ‘group efficiency factor’. In order that such factor is of general use, it was felt necessary to examine the applicability of the factor to different sizes of groups under varied subsoil conditions. With this in view, some model test results reported in literature of single and group of columns have been analysed and in the process an explicit relationship regarding the stone-column ‘groupeffect’ could be established.INTRODUCTIONThe field application of the stone column technology has gained momentum than the intricate design methodology due to its simplicity in installation and intuitive performance. The ground improvement is due to the complex interaction within the ‘unit-cell’ comprised of the installed column in ambient ground under sustained vertical stress; in association with the interdependence of problem geometry and material properties of the two different soils-one 'native' and the other 'back-filled'. The beneficial effects are increased load capacity, reduction in total and differential settlements, minimization of post construction settlements effected by accelerating consolidation, reduced risk of soil liquefaction, aiding in improvement of slope stability of embankments and natural slopes and effecting changes in the dynamic response. The ‘unit-cell’ concept of a tributary soil cylinder encapsulating an installed column with some reasonable assumptions and boundary conditions (Aboshi et al, 1979; Balaam & Booker, 1981; Van Impe & De Beer, 1983; Priebe, 1976; Saha & De, 1994; Saha; 2005, 2006, 2007, 2011, Saha & Das; 2007) deals with the load-settlement behaviour of the composite system. The present investigation is based on published field data from literature & validated with experimental study reported in literature. The study addresses the effect of group interaction of stone columns beneath a large area loading on ground settlement. The hydrotest load-settlement data of 12 large diameter oil storage tanks founded on stone column reinforced soil at Haldia1 and Kandla2 refinery sites in India; reported by Som (1997), has been analysed to quantify the group efficiency. The results as obtained are compared with experimental study on 2, 3 and 4 stone column groups at different spacing-diameter ratios in soft clay3 reported by Rao et al (1997) to validate the above analysis. A unique relationship between the column spacing and group efficiency has been obtained."

Jan 1, 2015

By Racquel Nottingham, Marc Mastrantuono, Freddy Lopez

In the digital era that we live in, connectivity and mobility play a decisive role in our daily activities. In this context, insufficient telecommunication infrastructure gives origin to the so called “dead zones” (areas with poor or non-existing cell phone reception), which hinder economic development in small communities and in many rural areas, since they remain invisible to a larger marketplace due to the inadequate cellular coverage. Several countries are working to identify these dead zones and with this information, establish strategies together with mobile providers in order to improve the existing mobile networks by expanding the coverage areas. As a result of the analysis, it is expected that thousands of telecommunication towers for 4G and 5G networks will be erected in the coming years. Telecommunication towers are slender elements that require large shallow foundations to verify primarily the safety against overturning. However in remote areas, it can be advisable to consider alternatives to the conventional shallow foundations, in order to optimize the use of materials (concrete, reinforcement steel, etc.). The following article presents an overview of intervention projects, where telecommunication towers were founded on micropiles. The micropiled foundations allowed to reduce considerably the dimensions of the originally planned shallow foundations. Furthermore, the use of micropiles allows for additional optimization, in combination with pre-fabricated foundations (i.e., precast concrete elements, etc.). This paper will focus mainly on the design and the execution of the micropiled foundation.

Sep 8, 2021

By Ronnie Melker, Joel Webster, Daniel Belardo, Thomas Hyatt

Quality assurance of drilled shafts is highly dependent upon the construction practices used during the excavation and concrete placement process. When performed under slurry, challenges are presented in maintaining borehole stability and placing a uniform and continuous concrete column. An integral part of the construction operation is to evaluate the as-built integrity to verify the drilled shaft is capable of safely transferring the required loads to the subsurface. One such case is exemplified by a project involving the expansion of an existing public transit rail line. The expansion required the construction of a new bridge bent supported by seven 5-ft diameter drilled shafts of various lengths. The specifications for the project required both Cross-Hole Sonic Logging (CSL) and Thermal Integrity Profiling (TIP) for drilled shaft integrity evaluation. Both of these post-construction non-destructive tests (NDT) are designed to detect anomalies or the presence of regions with reduced concrete quality. However, the implementation and methodologies of performing each of these NDT methods are significantly different. Cross-Hole Sonic Logging uses ultrasonic signals emitted from a transmitter in one access tube to a receiver in another access tube. Thermal Integrity Profiling measures elevated concrete temperatures during the curing process using embedded thermal wires. Both test methods require different access details and therefore have different costs associated to the contractor or owner to perform. This paper provides a detailed comparison of these NDT methods as performed on these seven drilled shafts. The associated financial and time costs to perform each method are compared and the results are discussed in detail. INTRODUCTION Drilled shafts are a fundamental deep foundation element that can be designed to resist large bending moments as well as to transfer large compressive axial loads through weaker upper soils to competent soils or rock below. Often times when the upper soils are very soft, lateral support by casing or slurry, or a combination of both, may be used to hold back the softer soils from collapsing into the hole before concrete has been placed. Due to the blind nature of drilled shaft construction and the qualities issues that may arise during the placement process, it is essential for design engineers to specify non-destructive testing (NDT) to assess the quality of the as-built drilled shaft. CSL and TIP testing are two NDT methods designed to detect areas of lower quality concrete or soil inclusions throughout the length of the drilled shaft and determine its overall quality. Each method uses different technologies and methods to achieve the results required to determine the as-built condition of the drilled shaft.

Jan 1, 2019

By P. Kiruthika, A. Murali Krishna

Soil liquefaction is a dangerous phenomenon that involves huge damages during strong earthquake ground motion event. Stone columns (SCs) are widely used as liquefaction mitigation element which is expected to perform the improvements against liquefaction hazard by densifying, increasing the stiffness and rapid dissipation of excess pore water pressure in the surrounding soil. Although in the recent times few studies on the behaviour of stone columns in the seismic zone has evolved, the performance of SCs in the multi-layered soils is not extensively examined. This paper presents the numerical investigations on the performance of SCs installed in the multi-layered soils as a liquefaction mitigation measure against the seismic loading. The acceleration time histories, Excess Porewater Pressure (EPP), vertical displacement and stress ratio evaluated along different depths using PLAXIS 2D. With the installation of stone column there is a considerable reduction in the acceleration amplitude, which in turn reduces the EPP and vertical displacement at different locations and the amplitude of reduction depends on the soil stiffness levels at the depth.

Sep 1, 2022

By Dipl. -Ing. (FH) Thomas Schmitt, Dr. Melvin England

Foundations in Geneva are difficult and expensive due a large overlayer of clay and silt above competent bearing material in the moraine. Common foundation schemes use deep barrettes or bored piles, first passing large, weak layers of soil before finally reaching acceptable, solid moraine with reasonable values of skin friction and end bearing resistance, thus requiring further deep penetration for the necessary length for load transfer in the moraine. Depths of more than 60 m (200 ft) in Geneva are common in this region. At the Onyx-Project Geneva Implenia Foundation Company also encountered these circumstances. Despite usual solutions Implenia referred to an old and well known, but still intelligent and in today’s words smart, efficient and economical solution. Using small shafts, passing the large layers of clay and silt, ending with the pile toe in the underlaying moraine with a belled or underreamed base was the technic adopted to save drilling time, reduce spoil and concrete, so finally reducing the CO2 footprint. Piles with enlarged base (“belled” or “underreamed”) are reported at the beginning of the 20th century, for example at Chicago, which has a quite similar geotechnical structure as Geneva with the need of deep foundations. The first pile base enlargements were built in hand-dug caissons with wood lagging and steel ring bracing. In the 50s and 60s piling works were more and more mechanized, driven by the development of more powerful cranes and specialized drill rigs. Additionally the first tools for mechanized base enlargement were invented around that period. This report describes the project situation at Geneva, the drilling and enlargement technique of the pile base, the verification of the design values with an in-situ bi-directional load test and the smart execution by reduction of CO2 and costs.

May 1, 2022

By Aditya Ayithi, William G. Ryan, Dean Herbst

"For rock socketed drilled shafts, it is a common practice not to include the frictional resistance of overburden soils into the nominal capacity estimation. The primary reason often being cited is “overburden soils resistance is negligible compared to that of rock socket resistance.” However, in certain geological conditions, where the rock layer is located at greater depths, friction resistance from overburden layers can be significant. In addition, at such great depths, shaft drilling becomes very complicated and expensive. In these situations, considering the resistance of the overburden layers can be an economic alternative.This paper presents a case study of an Osterberg cell (O-cell) load test conducted on a 161.8 feet long and 78-inch diameter instrumented test shaft. Based on initial designs, a 72-inch diameter rock socket of lengths 23 and 26 feet was required to provide a LRFD factored friction resistance of 3,200 kips. The load test results revealed that the material in the 72-inch diameter socket does not represent a true rock. However, the test results also proved that the factored friction resistance of overburden layers is greater than the required design resistance. Based on the load test results, it was decided to allow the overburden soils frictional resistance to be considered in the shaft design, resulting in significant economic savings.INTRODUCTIONRock socketed drill shaft design guidelines of various State Department of Transportation (DOTs) agencies allow friction and/or end bearing resistance of only the rock socket portion into the design capacity estimation. It is typical to neglect the frictional resistance of overburden soils. However, in certain geological conditions where the rock layer is at greater depths, friction resistance of the overburden soils can be significant. In this case the friction resistance of overburden soils was verified via the specified instrumented O-cell test program and then used as part of the design capacity.PROJECT DESCRIPTIONAs part of I-29 improvement project, Iowa Department of Transportation (Iowa DOT) planned to replace the dual four lane bridges that cross the Floyd River in Sioux City, Iowa with dual six lane bridges (Fig. 1). Expected benefits from this improvement include improved safety, traffic operations and roadway infrastructure conditions.BRIDGE SUBSTRUCTUREThe project consists of two individual bridges; a new south bound bridge and a new north bound bridge. The south bound bridge is 646-ft long and the north bound bridge is 644-ft long. Both are six-span, pretensioned and pre-stressed concrete beam bridges of varying width. Bridge foundations were designed such that the abutments of both bridges will be supported on driven steel piles and the bridge piers will be on drilled shaft foundations."

Jan 1, 2016

By Mario A. Terceros Herrera, Mario Terceros Arce, Antonio Marinucci

This paper describes the general principles of the expander body with post-grouting (EBI) system, and how it is similar in nature to a large-scale pressuremeter device. The results from the installation of an EBI can be used to provide information about the stress-strain characteristics of the soil adjacent to the device and to compute estimates of nominal axial resistance. As the EBI expands during grouting, pressure is applied to the in-situ soil surrounding the device thereby compacting/densifying the soil. The nominal axial resistance for small diameter piles/ground anchors can be increased due to the greater soil stiffness and shear strength around the device, larger surface and end area, and improved soil-to-EBI interaction in side resistance. The shape of the response curves depends on the geotechnical conditions of the soil (e.g., in-situ stress state, strength, and stiffness) and the installation method of the piling/ground anchor. This technique has been used successfully with different pile types and ground anchors in a wide range of conditions from very loose sands/silts to very dense sands and medium-dense gravels as well as in soft to stiff clays. This paper also describes a mini case history in which 80 piles were installed to support an office building, and the results of the static axial compression load tests performed on a production FDP+EBI pile is also included.

"This model specification includes sample text shown in normal font with commentary in italics. The commentary is intended to highlight project-specific items the specification writer should consider during development of the specification. In some sections, typical values are presented to indicate common practice, and these values may be changed to reflect project-specific requirements. The commentary should be removed before using the specification for a project. 1. SCOPE The work consists of designing, furnishing, installing, and testing helical piles used to support foundation loads (compression, tension and lateral), and any ancillary materials (e.g., load transfer devices, etc.) according to the project plans provided and these specifications. Unless otherwise noted, the installing contractor shall provide all labor, tools, equipment and materials necessary to install the required piles. The parties referred to in this specification are as follows: • The Owner is the property owner. • The Owner’s representative is the individual or firm hired by the Owner to design and oversee the overall project. • The pile designer is the individual or firm generally hired by the installing contractor to design the helical piles. • Installing contractor installs and tests (if necessary) the helical piles, and possibly tasks associated with the project. It is important to clearly define the roles and responsibilities of every party on each project to promote good communication and reduce potential for contractual misunderstandings. Different types of contractual vehicles (design-build, value engineering, etc.) require different roles and responsibilities for the various parties, which should be considered in specification development. The Owner will provide suitable access to the construction site for the installing contractor’s personnel and equipment. Unless specifically noted otherwise in the contract documents, the Owner will remove and replace any structures, utilities, pavements, landscaping or other surficial improvements in the work area as necessary to facilitate the work. The Owner will be responsible for overall construction oversight to minimize potential for developing unsafe conditions. The work may include post-construction monitoring of pile performance if required by the Owner or the pile designer to confirm performance of the piles subsequent to their installation. The work may also include installation of additional piles if the initial installation does not meet specified capacity or performance requirements. Responsibility for providing subsurface investigation shall be addressed in the bid documents. The Owner is responsible for providing to the installing contractor all available subsurface soils, rock and groundwater information and geotechnical testing data."

Jan 1, 2015

By Patrick J. Lydon, Gregory A. Terri

"The recently opened Mansueto Library at the University of Chicago campus was a 2012 OPA runner-up. The dramatic elliptical shaped dome of this structure tells only part of this structure’s story. The underground automated storage and book retrieval system below ground required excavations as deep as 55 ft (17 m). The system that allows the University to store many of its publications well below grade also required an approximately 50 ft (15 m) clear span for the perimeter walls between the lower level and street level slabs. The latter requirement allows the conveyors to operate freely to retrieve and transport publications up to the lobby level. The design-assist-build team worked together to develop the most cost-effective solution for below-grade work in this challenging urban and geologic environment.The perimeter of the new oval-shaped library is over 620 ft (189 m) long and sits in a central location on campus—adjacent to the Regenstein Library and two city streets and the Henry Moore sculpture, which commemorates the location of the first self-sustaining controlled nuclear reaction. The new library construction not only had to meet challenging structural and geotechnical requirements, but also had to be sensitive to its active and historic surroundings. The soils at the site consist of about 25 ft (7.6 m) of sand, followed by lean clay, generally increasing in stiffness to the top of the dolomitic limestone. Five to 10 ft (1.5 to 3 m) pockets of saturated sand also lie on the north side of the site at about 45 ft (13.7 m) below grade. The top of weathered rock varies in elevation from 59 ft (18 m) below grade in the south to 69 ft (21 m) in the north. There is 1 to 2 ft (30 to 60 cm) of weathered rock. Groundwater at the site is about 7 ft (2 m) below grade.The new structure would extend 55 ft (17 m) below grade through saturated sand strata and into weathered rock for part of the structure’s footprint, so it was critical that the new permanent retention system minimize groundwater seepage laterally through the structure’s wall as well as piping through the weathered rock below the structure. The perimeter walls had to be very stiff to minimize ground movement around the structure’s perimeter due to the significant clear span between slabs."

Jan 1, 2013

By Selvaganesh Selvaraju, Deepak Raj, Sandun N. Wimalasena

One of the world leading oil majors is carrying out a multi-billion-dollar expansion of its integrated manufacturing complex in Jurong Island, Singapore, the global oil trading and refining hub. Soil conditions at the site comprise 10-20m thick reclaimed sand, below which is 3-5m of soft marine clay underlain by stiff soils of the Jurong Formation. The conventional foundation solution would adopt driven precast concrete spun piles; however, precast spun piles have a high embodied carbon from the usage of steel and cement. In order to reduce the carbon footprint, an alternative solution comprising deep vibro techniques was developed. The EFFC-DFI carbon calculator was used to demonstrate the expected scope 1, 2 and 3 carbon emissions for both driven pile and vibro techniques. By using in-house, state-of-the-art fuel-efficient machines, alongside the innovative design concept and usage of natural materials such as sand and stones, actual CO2e emissions were reduced from a potential 21,000 tonnes, with the spun pile’s solution, to only 1,900 tonnes. The saved 20,100 tCO2e is equivalent to an average car driving 2,000x around the Earth’s equator. The paper discusses the application of soil improvement as a more sustainable, lower carbon alternative to conventional piled solutions.

May 1, 2022

By Thomas Domanski

Any type of deep excavation whether for Bored Piling, Diaphragm Walls or Contiguous Bored Piling Walls depends on forming a stable borehole with a defined cross-section to receive safely the permanent materials. In modern construction the excavation depth can reach well the range of 100 m and above. The diameters of the Piles reach often sizes of 2.5 m and bigger. Top casings in Bored Piles (Diaphragm Wall none) are rather short and stability below the casing, need to be secured by stabilization slurry. The boreholes need to be formed through a variety of different materials and stand open for an extended period. Without a safe stable borehole, it is impossible to produce quality products and work cost-efficient. The understanding and proper usage of a suitable slurry is a key element essential for the delivery of Foundation Elements with high quality and within a reasonable budget. The setting of mechanical and rheological parameters in specifications is necessary and helpful, but probably insufficient to embrace and control such a key element in the practical implementation of foundation construction. The proper selection, design, implementation and supervision of slurries on site requires both from Contractors and Engineers to understand how different slurries do function. Only with this knowledge the right decisions in slurry operations can be made. This talk is directed to give some help to both, Contractor’s and Engineer’s, in understanding how different type of slurries do work. (Which ones should be preferred in what kind of soils.) The better knowledge will help the Contractor to control cost and enhance production. The Engineer will be able to assist in arriving at the appropriate technical choices and include in the specifications.

Sep 1, 2022

By Sushant Upadhyaya, Deniz Karadeniz

As part of the widening of I-64 in Williamsburg, Virginia, an extensive subsurface exploration program consisting of Standard Penetration Tests (SPT), Cone Penetration Tests (CPT), Dilatometer Tests (DMT), and Vane Shear Test was performed. In addition to these in-situ tests, an extensive laboratory testing program was completed including Consolidated-Undrained Triaxial, Unconsolidated-Undrained Triaxial, Direct Shear, and consolidation tests. The strength and the compressibility properties are deemed conservative for Yorktown and St. Mary’s Formations when evaluated based on the current topography, the existing overburden pressure and SPT values. SPT exhibited low blow counts especially within Yorktown Formation due to the increased excess pore water pressures resulting in a localized liquefaction at the tip of the split spoon sampler corresponding to remolded or fully softened strength of the soil. Therefore, the applicability of the SPT correlated soil parameters somewhat leads to conservative designs with deeper piles to achieve a desired structural load demand. Generally, the in-situ estimated soil design parameters are found to be comparable with the laboratory test results corresponding to long-term resistance gain with time. It is of practical importance to employ realistic soil design parameters for design applications such as pile foundations to provide cost and schedule savings. This paper presents a discussion on the soil strength estimates and variability from in-situ and laboratory tests for realistic strength characterization of Coastal Plain deposits.

By Ashirbad Satapathy, Sanket Rawat, Ramanand Shukla, Ravi Kant Mittal

Bearing capacity factor (Nq) and Adhesion factor (α) are the key parameters for analyzing the load carrying capacity of pile foundations embedded in cohesionless and cohesive soils respectively. Numerous models are available in the form of charts or equations for the computation of these parameters and hence, have been adopted by most of the International and National standards. Indian Standard for the Design and Construction of Concrete Pile Foundations, IS 2911–Part 1 (2010), also makes use of charts detailed in its Annexure B. However, the sources of these charts have not been specified clearly, making it difficult to back-refer to the actual models to assess their basis for resolving any critical scenarios encountered during design. The present study aims at acquiring a distinct understanding of the development of these charts in order to bring more clarity to the design process of pile foundations. The given charts have been compared with various models specified in existing literature and international standards for the calculation of Nq and α for both driven and bored piles and hence, the basis of Indian Standard charts has been identified. Moreover, it is evident that the use of these charts complicates the process of automation of analysis and design of pile foundations as well as the associated optimization studies. Additionally, the manual entry of data especially, from the logarithmic graph of Nq, escalates the chances of error thus, making it a critical concern for design offices. Therefore, this paper also presents a non-linear regression model for Nq and α, developed using NCSS software for both driven and bored piles. Through multiple iterations, the value of coefficient of determination for Nq and α has been found to reach greater than 0.995. The developed equations can be simplistically used for both manual and automated analysis of pile foundations.

Nov 1, 2022

By Tatiana Tronda

"The territory of Belarus is characterized by nonhomogeneous ground conditions. In some cases soft ground layers can reach tens of meters in depth. Application of piles and other conventional foundations is rather difficult and expensive in such complicated conditions. Alternatively for the first time dry concrete columns were applied to improve the saturated soft soils at two sites. As there is no design methods for calculation of bases improved by dry concrete columns static penetration and static load tests were carried out to check the bases on availability. Considerable increase of toe resistance and Young modulus was achieved for all types of soil. Practical application, technology and test results are described in the paper. According to comparative calculations the cost of foundations on the base improved by dry concrete columns can be 32-75% lower than the cost of conventional pile foundations depending on ground conditions.INTRODUCTIONPile foundations, sand cushions or dewatering are usually applied in complicated ground conditions which are caused by presence of saturated soft soils. If the depth of soft soils reaches 20 m or more, conventional foundations have limited application, high labor and construction cost. A rational solution in such conditions is a ground improvement of upper soft soils. It allows the loads to be transferred on upper ground layers and the stresses to be dissipated considerably before reaching underlying soft ground layers.One of the effective ground improvement methods for saturated soft soils is the reinforcing by dry concrete columns (Fig. 1). The method allows saturated soft soils to be compacted and be drained at the same time. As a result strength and deformation characteristics of natural soils improve (Tronda 2013, ?????? 2014).Unfortunately, there is no design and computing methods for the ground improvement by means of dry concrete columns. However, at present the methods are under development on the basis of theoretical and experimental researches.TECHNOLOGYThe dry concrete columns are fulfilled in pressed wells according to technology of vibrostamped piles. Wells are pressed by vibratory hammer with the closed ended casing (Fig. 2) that provides compaction of surrounding soft soils. Then the casing is filled with dry concrete mix (Fig. 3). The casing end remains on the design depth and the casing is removed by vibratory hammer. The removing of the casing with vibration enables compaction of dry concrete mix inside the well. Dry concrete mix drains surrounding saturated soft soils improving its properties and the compaction speeds up the consolidation process. Over time the dry concrete columns fasten absorbing water from surrounding saturated soft soils that is need for hydration of cement (Fig. 4, 5)."

Jan 1, 2016

By D. K. ] [Gupta

The Foundations of the Shear keys and alround cut off for Power House -IV of the Western Yamuna Canal Hydroelectric Project at Bhudkalan, Haryana were to be laid at a depth of 26M below the N.S.L and 24.4M below ground water table. The foundation of the drainage sump was to be laid at still higher depth, Viz 29.OM below N.S.L. The Sub soil at the site consisted of Gravel with some amount of sand. The laying of the foundation at such a great depth, at a large depth below the ground water table and that too under such difficult sub-soil conditions encountered a large no of Geotechnical problems-viz excessive seepage, side slope sloughing and sand boiling during excavation. Under the circumstances at the site, the modified foundation construction procedure i.e a battery of M. S. Troughs was placed in flowing water conditions and concreted thereafter, resulting in a sizable cut in dewatering and reducing a significant amount of time and cost of construction affecting a saving of crores of rupees at the state exchequer. Sheet Piling was used to prevent side sloughing in the foundation pit.

Jan 1, 1996

By Charles M. Wilk, Lori Tiefenthaler

"Information presented in this paper can be used to support deep soil mixing, subsurface grouting and slurry wall technology as sustainable construction technologies. Ordinary Portland Cement (OPC) is the default cementitious material used by Deep Foundation Institute (DFI) Members for geotechnical work. Owners, engineers and contractors can contribute to the sustainability of a geotechnical project by increasing the use blended hydraulic cements and industrial byproducts to replace some of the OPC in mix designs. Sustainability is defined as the quality of not being harmful to the environment or depleting natural resources. Production of cementitious materials consumes natural raw materials and energy while also generating air emissions and waste. Life Cycle Assessments can be used to compare the relative environmental impacts of one cementitious material to another. Blended hydraulic cements (BHCs) are interground (or blended) mixtures of Supplementary Cementitious Materials (SCMs) with OPC. Commonly used SCMs include fly ash, ground granulated blast furnace slag (GGBFS) and limestone. Examples of industrial byproducts commonly used in geotechnical work include coal combustion residuals (CCR) (aka fly ash), and ground granulated blast furnace slag (GGBFS). Much of life cycle impact of these SCMs and industrial byproducts have already been borne by the industries that generated them. There is increasing awareness to LCA and sustainability of different materials used on projects. This is evident in the application of the Leadership in Energy and Environmental Design (LEED) program. The savings in environmental impact with the use of SCMs and industrial byproducts can make proposed use of these materials in a geotechnical project more attractive in terms of sustainability. This paper presents (a) information that compares published life cycle assessment data of OPC, BHCs, and slag cement (SC) to illustrate the potential benefits to sustainability and (b) general strategies for positioning a geotechnical application, use, project design or cementitious material mix as a more sustainable alternative"

Jan 1, 2017

By Abolfazl Eslami, Masoud Zare, Ali Asadi, Ali Abrang

"Physical small scale models for study of deep foundations can be performed in simple chambers (1g), calibration chambers (CC), and centrifuge apparatus (ng) which involve some limitations and difficulties. In recent years, Frustum confining vessels (FCV) have been developed for physical modeling of deep foundations. This device is frustum of a cone shape that applies a steady pressure on its bottom and creates a linear stress distribution along its vertical central line. A new FCV which has been built in AUT is introduced. This device has a height of 1200 mm, top and bottom diameters of 300 and 1300 mm, respectively. Through the application of bottom pressure up to 300 kPa, the insitu overburden stress conditions equivalent up to 40 m soil deposits consistent to the embedment depth of commonly used piles. Observation indicated that there is approximately a linear trend of stress distribution, and this device can create realistic overburden stress in the desired control volume along the central line. Moreover, a couple of compressive and tensile load tests were performed on steel tubular open end model piles driven in sand with length of 750 mm and different diameters and L/D ratio between 8-15. Comparison of load capacity between tested and full scale piles demonstrate a suitable conformity for similar confinement conditions. Therefore, the FCV can be realized as an appropriate apparatus for investigation of piling geotechnical behavior and examination of construction effects.IntroductionDeep foundations are designed as foundation system for supporting heavy loads, high rise and important structures. Different theoretical, numerical and experimental approaches have been developed to study the geotechnical behavior of deep foundations. Experimental methods are employed to clarify directly pile-soil interaction and because of repeatability, analogy, rapid measurement and cost efficiency, physical modeling can be realized as an intermediate technique compared to element testing and full scale load tests."

Jan 1, 2015

By Dharmil S. Patel, Zoyav S. Benyaminov, Cassandra A. Wetzel

Rehabilitation of the Henry Hudson Bridge is nearing completion, connecting Spuyten Duyvil in the Bronx to Inwood Hill in Manhattan, New York. Constructed in 1936, the Henry Hudson Bridge spans 840 feet over the Hudson River. Challenging geotechnical aspects of this Project required a team of innovators to overcome. Rehabilitation of the existing bridge involved the replacement of sixteen bent pedestal substructures, two abutment pilasters and installation of new deep foundations at the skewbacks. However, the Bridge, roadways, adjacent Metro-North Railroad (MNR) structures and New York City (NYC) Parks land were to remain open to the public for use, with minimal disturbance. In addition to physical constraints, geologic site conditions varied widely across both sides of the River, with varying bedrock quality and depth, greatly impacting the proposed design and construction. Extensive analysis of bedrock conditions was conducted to locate areas of potential wedge failure. The implementation of anchors was used to reinforce rock stability where pedestals and pilasters were replaced. This paper describes several challenging technical and natural aspects overcome in the rehabilitation of the Henry Hudson bridge foundations, including varying geologic site conditions, access restrictions, construction limitations, project specifications and design requirements.

Sep 8, 2021

By Ramin Motamed, Fahim M. Bhuiyan, Raj V. Siddharthan, Joseph Toth

The difficulty in material characterization and the erratic response of cemented soil layers, such as caliche in the Las Vegas valley, creates challenges for practicing engineers to reliably predict the response of deep foundations. The focus of this paper is the numerical prediction of axial response in drilled shaft foundations, which are commonly used in infrastructure projects (i.e., bridges and tall buildings) in Las Vegas, NV. The prevalence of hard caliche layers with variation in the degree of cementation add to the complication in numerical modeling. In this study, the applicability of two existing t-z models, developed for Florida limestone and soft rock, was evaluated based on numerical simulations of three bi-directional load tests conducted at caliche-dominant sites. The corresponding top-down load tests were also simulated for further assessment. A MATLAB-based finite-difference program, NVShaft, has been used to implement the mentioned t-z models in axial load analysis. Complexity originating from drilled shaft construction and the interaction with caliche during one axial load test resulted in a stiffer predicted response compared to measure data. For the other two load tests, both t-z models produced comparable load-displacement responses. It was observed that the t-z model for Florida limestone predicted relatively stiffer responses and higher drilled shaft capacity.

Sep 8, 2021