Search Documents

By Andreas Cestonaro

Roll grade evolution in plate mill applications is traditionally following the development in hot strip mills. New grades normally find their way into service only after being successfully implemented in hot strip production. The majority of the plate mills worldwide are using work roll grades that have been invented before the 1980’s. But today the demands in the mills are pushed by sophisticated product mixes and longer rolling campaigns. The result of this development is a higher wear rate on the work rolls and as a consequence roll hardness is increased and advanced roll materials are used. The backup rolls are also affected by this. The wear rate is higher and the mechanical impact in terms of contact pressure and work hardening is increasing. This paper outlines the results of the roll grade development at Gontermann-Peipers and introduces new materials for work and backup rolls for plate mills.

Jul 30, 2018

By Christian Geerkens

Increasing requirements on slab quality initiates SMS group in developing products with a high sophisticated level regarding production and process. These characteristics are represented by SMS group’s HD family. HD stands for High Definition or the improvement of product quality via higher precision of the casting processes. A deep look inside into casting process is realized by the use of fiber optical equipped HD mold. High definition casting process control is assured using the HD spray and HD size. For objective, environmentally friendly and highly informative analyze of the inner quality of the cast products the new HD scan is present.

Aug 16, 2017

By Erich Bartel

The Kocks Rotation Mill - KRM- is an innovative elongation method for seamless tube production up to 4.5’’ diameter at production levels up to150,000 TPY. Using the principle of cross roll elongation, the machine rotates four rolls around the workpiece. A retained mandrel sets the wall thickness to a precision that exceeds existing industry norms. The KRM process performance has been truly excellent. Attributes include high billet weights, elongation of up to 9.5 in one pass, and eccentricity at or below +/- 5.0%. The flexibility of the process allows a wide range of steel grades to be produced at any wall thickness with little or no mill down time. Surface quality and yield are also greatly improved. Based upon the small foot print of the KRM rotor as well as the simple mandrel manipulation system, the installation cost of the KRM is significantly lower compared to other elongation methods. The reasonable cost of the machine, combined with greatly reduced foundation requirements, reduced ceiling height as well as simple utility connections reduce the initial investment for a new or upgraded mill. Finally, lower roll and mandrel costs allow high quality production at greatly reduces cost/ton.

Aug 16, 2017

By Alexandre Rizek Schultz

Silat, Siderúrgica Latino-americana, selected Russula as the main engineering contractor for their 700,000 tpy Greenfield steel plant dedicated to long and flat steel production. The project is currently under construction in the district Guararu in Caucaia in the metropolitan region of Fortaleza. The project will be developed in two phases. First phase: 600,000 tons per year rebar mill and 60,000 tpy steel mesh line; Second phase: 700,000 tpy melt shop (90 ton/hr EAF and 4 strand continuous caster for billets up to 180 mm x 180 mm).

Aug 16, 2017

By Armando Vazquez Arredondo

Tenova Goodfellow Inc. has successfully installed the proprietary EFSOP® (Expert Furnace System Optimization Process) system in over 80 installations worldwide. For over 15 years, the EFSOP® System has successfully achieved its main objective of improving performance and operating costs through the reduction of electricity, oxygen, methane, injected and charge carbon use. Using the off-gas information provided by the EFSOP® System, Tenova Goodfellow Inc. has now developed a solution for detecting abnormal water events within the EAF steelmaking process. When water form enters the EAF, it immediately forms into water vapor (H2Ogas) and a proportion of the resulting water vapour will further react and dissociate to H2. Effective water detection technology must be capable of detecting BOTH forms of water; H2Ogas & H2. Tenova Goodfellow has the technology to measure in real time and simultaneously H2Ogas & H2. This paper will provide a summary on how the EFSOP Water Detection Technology® is used during the EAF operation. Details regarding the technology, software, alarm rate and information on sensibility water trial tests will be provided within this paper.

Aug 16, 2017

By Antônio Augusto Gorni, Fabio Adriano da Silva, Emanuelle Garcia Reis, Afrânio Márcio Costa

Gerdau Ouro Branco´s plate mill started the operation in 2016 with high level technology. Stands out the capacity to produce different thicknesses in a same plate, therefore allowing special service for sectors such as building structures, bridges, shipbuilding and mechanical applications. The purpose of this study is to present the first results obtained in this innovative product in Brazil. Some slabs of EN10025-2 S355JR+AR steel were rolled and were evaluated the dimensional tolerances, mechanical properties uniformity, grain size, surface and internal qualities. In addition, a correlation was observed between slab and plate thickness reduction and internal plate quality. The results show that this technology can be used with adequate performance for these steel grades in the current market.

Oct 1, 2019

By Valeria Collini, Antonello Mestroni, Enrico Plazzogna

The Danieli Group is deeply involved in the technological improvements stimulated by Industry 4.0 concepts widely applied to the metals industry and process automation. The so-called "Intelligent Mill" is the natural evolution of the company’s consolidated know-how and undisputed leadership in the fields of mini-mill and turnkey plants. Complete and structured data collection is the basis for real-time analysis and process optimization in terms of quality, efficiency and easy maintenance. A centralized repository of information is possible thanks to the strong interconnection between process control system architecture and intelligent sensors, together with dedicated software tools leading to an intuitive approach to data analytics.

Oct 1, 2019

By G. Martino, F. Silva, Emmanuel Marchal

The definition of the chemical specification at multiple steps of the steelmaking process is very common in the industry. Among all elements and compounds, the Sulphur content has a special control over several stages, from the coal blend to the final products. Coke, iron and steelmaking specialists usually agree on a static specification for each intermediate product according to their local operation capacity and production cost. However, local decisions have major impacts on the whole production chain and many global factors should be considered in order to make the best decision. In this study, we will exemplify focusing on Sulphur content concepts and techniques that could be applied to many decisions in an integrated carbon steel plant. The variation of coal and coke prices, the desulphurization cost and time, the processes operating points, the hot metal rate at converters, prices and demands of low and ultra-low Sulphur steel grades are some of the integrated factors that are usually disregarded during the specification process. Mathematical modeling presents itself as a proper option into dealing with all the complexity that emerges from integrating all these processes' trade-offs and decisions. This study presents the results of a mathematical model that encompasses economic, thermal, chemical, and mass balances, physical quality of materials and productivity constraints of all processes of a hypothetical integrated carbon steel plant. It optimizes the iron and steelmaking process on a global and unique objective, dynamically defining targets for product quality to achieve the lowest steel production cost. This study details multiple market-plant scenarios in order to compare economic and operating results of a static vs dynamic specification practice.

Oct 1, 2019

By Markus Reifferscheid

Industry 4.0, Digitalization, Internet of Things (IoT) and Cloud Computing are predominant topics in the world economy at the moment. At the ABM week 2017 Dr. Markus Reifferscheid, Head of Research & Development of SMS-group, will talk about the proceeding digitalization in the steel industry with selected examples of SMS-group. He will present advanced concepts and solutions which are currently being developed.

Oct 30, 2017

By Jesús A. Carlos Cornelio

Since their discovery in 1991 Carbon nanotubes (CNTs) have attracted much interest due to their remarkable mechanical, thermal, electrical, chemical and optical properties. In connection with their mechanical properties, CNTs have been studied in various forms for tribological applications including their use as lubricant additives for oil and water. In this paper the tribological properties of CNTs (SWCNTs and MWCNTs) when used as lubricant additives are studied under rolling-sliding conditions in a twin-disc testing machine. The tests were performed using 5% of creepage and pressures of 0.8 GPa and 1.1 GPa. Used functionalized nanotubes were modified with carboxylic acid ultrasonically dispersed at different concentrations (0.01, 0.05%). The results indicated that the presence of carbon nanotubes leads to a decrease in both friction coefficient and wear rate for both systems studied (oil and water).

Jul 31, 2018

By Chad B. Donovan

There is a strong need in North America and other major steel producing markets where major capital investment in new equipment has been minimal over the past several years to make improvements to existing casting machines. In many cases, very cost effective improvements can be made to existing equipment in order to maximize the efficiency and production of an older designed continuous caster, a classic caster. SMS Group and its predecessor companies have been maintaining continuous casting molds for over forty years. This experience has allowed SMS Group to intimately understand the advantages and disadvantages of each design. The most vital component of the continuous caster is the mold copper design, as it has the most influence over the ability to cast a quality product. Updating to a modern copper design is less complicated than most steel producers think and the benefits are significant. Premium mold coatings such as UniGuard® and NanoGuard® allow casters to guard against exposed copper and wear while producing quality products for record campaign lengths.

Oct 30, 2017

By Túlio Magno Fuzessy de Melo, Luciano Santos Marques, Vicente Tadeu Lopes Buono

The influence of the coiling temperature after hot strip rolling on the microstructure and on the tensile and hole expansion properties of a 800 MPa multiphase steel was investigated. For the temperatures between 150°C and 600°C the microstructure consisted of a ferritic matrix with a dispersion of fine martensite-austenite (MA) and regions of degenerated upper bainite. In all cases the ferrite presented a heterogeneous mixture of polygonal, quasi-polygonal and acicular grains. The yield and tensile strengths showed a tendency of decreasing with the increasing coiling temperature, probably because of the larger fraction of MA particles at lower temperatures and higher fraction of quasi-polygonal ferrite at higher temperatures. The elongation was not significantly affected by the variation of coiling temperature. The average hole expansion ratio showed a maximum of 80% for the material coiled at 400°C and fell below 50% only for the coiling temperature of 150°C, probably due to the larger hardness difference between the ferrite matrix and the MA particles.

Oct 1, 2019

By Roman Vaynshteyn

In places where Blast Furnaces are usually located, climatic factors may be unfavorable. Raw materials may be exposed to e.g. rain during transport/storage, bringing moisture into the process with consequences for stability and hot metal cost. This paper describes a technology for drying and pre-heating pellets and coke in the stockhouse. It does not require additional handling or logistical equipment and does not introduce extra transfer steps and degradation. Not only can moisture content be reduced, it can be controlled to a stable level by the operator.

Aug 16, 2017

By Jose Maria Rodriguez-Ibabe, Ronaldo Antonio Neves Marques Barbosa, Douglas Glenn Stalheim

Major costs in the production of both flat and long commodity grade structural steel products include alloy, labor and energy. Flat and long commodity grade structural steels such as ASTM A36, ASTM A527Gr50, S235, S275, S355 and other equivalent world societal standards represent over 500 million annual tons worldwide. These simple commodity grades consist of a minimum of three base common alloying elements, carbon, manganese, silicon and then can be supplemented with microalloying elements of either vanadium or niobium. Since 2016 raw material costs for two of the five alloying elements in these commodity grade structural steels, FeMn and FeV, have risen significantly and/or have become volatile making it difficult to maintain stability in profitability for these commodity grades. For steel plants producing hundreds of thousands and in some cases over a million tons annually of these common structural steel grades because of the significant alloy cost increase for Mn and V alloy additions has squeezed profitability of these grades. These grades typically represent the base loading for cost controls in most all steel plants and hence a significant cost increase or volatility in two of the five elements used for these grades having a negative effect on overall production costs. However, with a proper strategy for alloy designs working in conjunction with the mills existing processing capabilities to achieve the desired end metallurgy/mechanical properties, alloy costs and operational efficiencies can be realized.

Oct 1, 2019

By John Hinton

Electromagnetic based (EM) sensor technology has been shown to detect changes in the magnetic permeability of steel strip travelling down the run out table after rolling. Measuring below the Curie temperature, these changes can be interpreted in terms of the phase transformation from austenite (paramagnetic) to ferrite (ferromagnetic). These real time measurements provide a detailed insight into the changes in the structure at high temperature providing the steel producer with feedback on quality control, product consistency and product development. However unlike mill microstructure models, the sensor measurement provides a point reading at a distance through the cooling course. To map the transformation in more detail, a sensor array is required along the length of the Run Out Table i.e. to measure points on the austenite to ferrite transformation curve. This paper describes the process and metallurgical factors that should be considered in the optimum design of a sensor array, i.e. the number and location of the sensor heads. Examples of cooling strategies for different steel grades e.g. low carbon, structural and dual phase steels are used to demonstrate the importance of sensor location. In addition, the effect of variability within typical industrial parameters e.g. cooling speed, on the sensitivity of sensor output and location will be considered.

Oct 1, 2019

By Andrelio Marcos Ribeiro, Lucio Ribeiro Camisao, Antonio Carlos Ataíde, Alan de Sousa Pereira, Renato Siqueira Campos

The annealing and pickling line n. 1, responsible for the production of stainless steel 3xx, 4xx and 430a in thicknesses from 4 to 0.4 mm, has two vertical strip accumulators. These are intended not to let the material exceed the determined time in the furnace and in the pickling, and consequently do not cause defects like burning and excessive pickling. Strip accumulator n. 1 avoids the line from stopping during welding execution of the coils in the welding machine. In sequence, the strip accumulator n. 2 avoids the line from stopping at the end cutting of the tips, and in the coils removal from the pickling. The strip accumulators have a roller table that during the strip accumulation moves vertically downwards while its counterweight moves vertically upwards, and do the inverse movement when the material is released. On December 12th 2018, the failure occurred in the strip accumulator n. 1, where it was verified that the shaft of one of the pulleys had been fractured by high-cycle mechanical fatigue, which was characterized by alternating bending. With the fracture of the shaft, occurred the unevenness of the counterweight that damaged the guides. Failure analysis of this occurrence was based on the PDCA methodology, when was verified a weld between the shaft and the pulley. The analysis of the microstructure transformation in the molten zone, in the heat affected zone and in the base metal was carried out in an optical microscope, and no abnormality was observed. It was also carried out the end test by penetrating liquid, finding an inadequate weld in its geometry, as well as longitudinal trunks along the center of the weld bead. However, after a huge investigation of the causes, it was found that the failure was triggered by an inadequate design of the pulley shaft. It was also verified that the shaft had an open measure, inadequate for the operational context. After the analysis, action plans were drawn up based on the FMEA methodology to inhibit the failure recurrence.

Oct 7, 2019

By Alim Ullah

The paper discusses the necessity of upgrading low-iron containing ores, giving as an example, NML-Tata Steel Project in the Quebec-Labrador region of Canada. As cooling of pellets is generally a bottle-neck in most pelletizing plants, examples are given of the methods used to improve cooling in the existing plants and a simple, low-cost alternative, tested on a pot-grate system, is presented. The procedure described is applicable to sinter plants also. The trends in iron and steel production worldwide are then given, as well as the reasons for the increase in steel production by the Electric Arc Furnace (EAF) route. The stoichiometric and thermodynamic requirements for producing iron, irrespective of the process, are explained. The different ironmaking processes, especially the Direct Reduction (DR) ones are briefly discussed, outlining recent improvements made to some of them. The pros and cons of producing cooled DRI and Hot-Briquetted Iron (HBI) are given with predictions made for their future growth. An alternative to cold-briquetting of DRI fines is also discussed. Highlights of an ironmaking processes which is at the laboratory/pilot plant stage are given.

Aug 1, 2018

By Luis Acainas Caballero, Karl Hoen, Stephan Krämer, Christoph Klein

The situation of the steel industry is still challenging. Worldwide overcapacities have an impact on profitability. More than ever, the point at SMS group is to provide the steel industry with flexible and profitable technologies and systems over the whole process chain. One example for that is the thin slab casting and rolling technology and, in particular the CSP® technology (Compact Strip Production), being well established for hot coil production. From its introduction in 1989, CSP® technology has been continuously further developed. Today, on a CSP® plant, the full range of high-quality steel grades can be produced with tightest geometrical and metallurgical tolerances under optimal economic conditions. With the introduction of semi-endless rolling and, as a further step, the endless rolling process, the product range for thin and ultra-thin products has been further enlarged, allowing for the production of hot rolled coils with a thickness of 0.8 mm for low carbon steel grades. Also high-strength steel grades may be produced with gauges below the minimum product thickness that can be achieved in a conventional-type hot rolling mill. Another step in the further development of CSP® technology is digitalization. In December 2016, the CSP® plant of Big River Steel (BRS), located in Arkansas, USA was put into operation. It is the first learning steel mill in the world. The CSP® plant of BRS comes with innovative technologies, providing impressive operational results right from the beginning.

Oct 1, 2019

By Wolfgang Kern

The implementation of the Gas Treatment Plant (GTP) for CSPECEM, Ceara-Brazil is a result of the closed partnership between Paul Wurth Italia S.p.A. and DMT, the German leading company in Coke Oven Gas Treatment Plants. In addition to technical issues reducing emissions, avoiding of waste and saving environment and energy were technical challenges during the engineering phase. Below mentioned three descriptions of technical solutions represents examples of a number other innovations based on DMT’s know-how and experience in the field of by-product plants. Generally the design of the complete GTP is based on the consideration of modern features and design upgrading, with the aim of a safe operation with stable conditions and a long-living cycle of the whole of the plant.

Aug 16, 2017

By Nicola Santangelo

The current economic crisis and growing environmental issues have led the steel industry to face the simultaneous effects of low demand and production overcapacity in a globalized steel market, whilst confronting high energy prices and the need to comply with the green economy. Heat Recovery from waste gas of the Electric Arc Furnace (EAF) represents one of the greatest opportunities to reduce the consumption of primary energy and reduce the CO2 emissions in steel industry. The heat of the off-gas, if recovered and converted into electrical power, can make the whole Fumes Treatment Plant autonomous from the electric point of view, thus making it a “Zero-Energy FTP”. The concept is to substitute the Cooling Components (Water Cooled Panels and Air Cooler) are substituted with Heat Recovery Components (Hot Water Cooled Panels and Heat Exchanger). The recovered heat can be converted into power by using an Organic Rankine Cycle (ORC) turbine. The heat recovered by the HWCP and the Heat Exchanger is characterized by a variable thermal power, which affects the efficiency of the downstream ORC System. Danieli, in collaboration with the University of Udine, has developed the Thermal Stabilizer Unit (TSU). Danieli has realized the first step towards Zero Energy FTP at ABS steelmaking plant (Italy) by installing a CHR® - Clean Heat Recovery. This plant has been started up on 17th October 2014. The HMI of the CHR® is integrated in the HMI of the furnace, so all the process could be kept under control by the furnace operator. At ABS recovered thermal power reaches 5.5 MW. The max power production reached with CHR plant in ABS (over 1MW of electric power) consents an annual saving of approx. 500,000 EUR.

Aug 16, 2017