Search Documents

By R. Peterson, D. C. Popko, J. Y. Hwang, R. McChesney, A. M. Hein, R. C. Greenlund, M. Jeong

MTU is conducting a study to recycle and reuse the aluminum waste generated from various segments of the aluminum smelting industry. This research is supported by the U.S. Department of Energy and industry. A portion of this effort is to determine the operating efficiencies of Eddy Current Separation, comparing separating characteristics of white and black dross. The results of this effort will be presented here.

Jan 1, 2000

By Maribel L- Saucedo-Muñoz, Toshiyuki Hashida, Victor M. Lopez-Hirata, Shin-Ichi Komazaki

"Small-punch tests were conducted at 4, 77 and 293 K on three types of austenitic stainless steels JNl, JJl and JK2, which were solution treated, water-quenched and then aged at 923, 973, 1023 and 1073 K for 5 h. Small-punch test energy was employed for the evaluation of the aginginduced embrittlement behavior in these materials. Fracture surface of small punch test specimen for the solution treated steels exhibited a ductile fracture, showing the highest SP test energy values. The presence of intergranular brittle fracture was observed in aged specimens. Smallpunch test energy decreased significantly as the aging process progressed. The highest and lowest decrease in small-punch test energy with aging temperature occurred in JNl and JK2 steels, respectively. The decrease in small-punch test energy showed to examine appropriately the aging-induced embrittlement in these materials. The difference in aging-induced embrittlement behavior for these steels was explained based on the volume fraction of intergranular precipitates in aged samples.IntroductionA high level combination of strength and toughness is required for cryogenic structural materials used in the superconducting magnets of fusion nuclear reactor. This requirement is beyond the capability of conventional austenitic stainless steels [1]. The Japan Atomic Energy Research Institute (JAERI) developed new cryogenic JNl, JJl and JK2 austenitic stainless steels. The structure of superconducting magnets is supposed to be constructed by welding thick plates of this kind of steels. Thus, most of the components are exposed to thermal cycles. The slow cooling may cause microstructure changes in both the base material and weld zone. These changes may also decrease the fracture toughness of these materials at cryogenic temperatures. Therefore, it is important to study the effect of thermal aging on fracture toughness behavior for these steels. Konosu et al. [2] carried out a study of the effect of thermal aging on the mechanical properties for JNl steel using tension and fatigue tests. Kwon et al. [3] evaluated the deterioration in fracture toughness at cryogenic temperatures for the isothermally aged JNl steel by means of the Small-Punch (SP) test. No other reports were found about the cryogenic fracture toughness behavior for this kind of steels. To evaluate the cryogenic fracture behavior, the elastic-plastic Jrc value is a good alternative [4,5]; nevertheless, the standard required specimen size makes it difficult to be used for the fracture toughness evaluation in small zones."

Jan 1, 2011

By Corby Anderson

The efficient separation of palladium from the transition metals copper, nickel and iron can be effected by passing a leach solution of these metals through a column of the silica polyamine composite material, WP-1, patented by Purity Systems Inc (PSI), Assignee, University of Montana with exclusive license to PSI. The separation can be done at the intrinsic pH of a nitrogen species catalyzed (NSC) oxidative pressure leach solution (~0) and stripping of the palladium from the composite can be effected with hydrochloric acid/ammonium chloride solutions at 50oC. Batch capacities of the composite for palladium are ~ 1.8 mmol/g resin. The possibilities for isolating the metal from the strip are discussed. Given the proven longevity and rapid capture kinetics of the polyamine composites, this new approach should prove to be an economically viable alternative to the multi-step concentration processes practiced in the PGM industry to date.

Jan 1, 2003

By Helena Byrdziak

KGHM Polska Miedz SA, in existence since nineteen seventies, operates three underground mines and three smelters with total production of over 400 000 mtpy of electrolytic copper. Its impact on the environment, very serious in the past, has been gradually reduced. While in general emissions into the air and water have been brought under control, attention recently has shifted to the disposal of wastes and residues. The main streams of wastes are flotation tailings, slags and dust captured from the dedusting systems. Much effort has already been expended and is still being spent to utilize this waste for by-products production or to dispose of it within the process by recycling. The most effective measures taken up thus far, as well as present activities directed at tailings disposal, are presented.

Jan 1, 1997

By A. D. Zunkel

The zinc in electric arc furnace dust (EAFD) arises from the fuming and oxidation of the zinc present, mainly as galvanizing, in automotive scrap. The dust is collected from the electric furnace offgases in bag filters and is classified by the EPA as a hazardous waste (K061). As more zinc is used in galvanized sheet on automobiles and more automobile scrap is recycled via the EAF, the more zinc will be available for recovery and recycling. EAFD will become a more prevalent and important source of zinc compared to the traditional zinc sulfide concentrates ifit can be cost effectively processed.

Jan 1, 1995

By J. W. Holzenthaler

Teams continue to play a major role at the Phelps Dodge Mining Company El Paso Operations, especially during the present time of low copper prices. The El Paso Operations' teams have taken the initiative during this copper market downturn and have helped reduce operating costs significantly. Because of this, Phelps Dodge El Paso Operations has continued to grow within the team process by creating a total, non- exempt salaried workforce. In the last year alone, the El Paso Operations have implemented three major initiatives to accommodate the team process. The first was the creation of "guiding principles", a policies and procedures handbook. Second was the "zero and beyond" safety initiative. Third was team compensation. In addition, the Copper Products Company has now adopted a work-team environment, following the lead of the refinery.

Jan 1, 1999

By W. F. Whittaker

Systematic control of process parameters during electrorefined copper cathode production and final product inspection ensures high quality of produced "ORC brand copper. Since 1986, substantial increases in tankhouse productivity have been achieved by a number of technological and process control changes. This paper reviews the changes implemented to achieve higher productivity and cathode quality.

Jan 1, 1992

By James C. Foley, David K. Rehbein

"In-situ characterizations of green state part density and sintering state have long been desired in the powder metal community. Recent ·advances in non-contact electromagnetic acoustic transducer (EMAT) technology have enabled in-situ evaluations of the acoustic attenuation and velocity as sintering proceeds. Pure aluminum (99.999%) and aluminum alloy powders were prepared with high-pressure gas atomization (HPGA). The powders were pressed in a uniaxial die and examined with acoustic waves for changes in velocity and attenuation during sintering. The changes in acoustic properties were correlated with sample microstructures and mechanical properties. Evolution of the acoustic echo train during sintering is shown to provide information on the state of sintering as well as having the potential for detection of interior flaws.IntroductionThe versatility of powder metalallurgy (PIM) technology in the manufacture of complex shapes has enabled an increasing amount of wrought and casting production capacity to be converted to PIM technology. However, ultrasonic inspection of green components produced using PIM techniques remains a challenge and is not generally practiced [1]. Inspection of PIM components in the green state is highly desirable, because the green part can be reclaimed with only accepted components being subjected to further costly processing. Another potential benefit is characterization and greater understanding of the sintering process itself. An increased scientific understanding of the sintering process enables intelligent process control, greater reliability of the production process and a lower rate of rejection of the finished product. In order to realize these potential benefits, it is necessary therefore that accept/reject criterion be based on real time nondestructive evaluation of the green-state components and the sintering process.Most current nondestructive inspection techniques suffer from their inability to perform inspections below the near-surface region with the exception of X-ray and to some extent pulsed eddy current [2]. X-ray inspection requires extensive shielding of production personnel and expensive film and film processing. While development of pulsed eddy current techniques have lessened the impact of the well-known skin effect, the depth of penetration of the induced eddy currents remains somewhat of an issue [2]."

Jan 1, 2000

By C. O. Bounds

The performance of AB5-type alloys for hydrogen absorption including the electrochemical absorption as an electrode for rechargeable batteries has been demonstrated' to be a complex function of the composition, microstructure and surface condition. The compositional studies have focused primarily on substitutions for Ni on the B-site (e.g. Co, Al, Mn, etc.). This current study examines the effect of rare earth substitutions for La on the A-site and considers both other "light" rare earths (Ce, Nd, Pr) and "heavy" rare earths (Dy, Sm, etc.).

Jan 1, 1997

By Michael S. Moats

As commercial copper electrorefineries look to expand their capacities by increasing their operating current density, the likelihood of anode passivation intensifies. To improve the industry?s understanding of the passivation phenomena, the role of anode composition was evaluated. While previous studies have focused on studying one impurity element at a time, this study was conducted using forty-four commercial electrorefining anode samples supplied by ten copper companies The passivation response of each sample was evaluated under accelerated galvanostatic conditions in synthetic copper electrowinning electrolyte at 65°C. This information allows for correlations between composition and passivation tendencies over a wide range of impurity elements and concentrations. It was found that selenium, tellurium, silver, lead and nickel accelerated passivation. It appeared that oxygen accelerated passivation when increased from 500 to 1500 ppm, but further increases did not have an effect. Arsenic was the only impurity found that inhibited passivation.

Jan 1, 2006

By Kwang-Ho Lee

The Onsan copper smelter of LS-Nikko Copper Inc. has operated the Mitsubishi continuous process along with Outokumpu process since 1997. Mitsubishi process is a bath smelting process which needs adequate melts for smelting reaction in the furnace. After a campaign shutdown it requires time to make a start melt. Onsan smelter has had much experience in flash smelting, including the improvement of the concentrate burner which is one of the most important parts in a flash smelting furnace. Based on this experience, the lances of the Mitsubishi smelting furnace were modified in order to making the starter melt with flash reaction. In 2004, the flash reaction in the Mitsubishi S-furnace was completed and was able to make the starter melt using these modified lances. Although at that time it was still under development it reduced the time required to make the initial bath-melt by about half.

Jan 1, 2006

By Guozhu Ye, Mikael Lindvall

"Swedish iron ore contains about 0.1 %V. The vanadium is reduced to the hot metal in a blast furnace and oxidised to the slag in a converter. The high V-content, up to 5 % V, leads to a very limited external application of the steel slag in Sweden. Since 2004, MISTRA - the Swedish Foundation for Strategic Environmental Research has together with the steel and mining industry in Sweden and Finland initiated and supported a long term project aiming at efficient recovery of vanadium in the slag, and at the same time a useful slag product with low V-content. The proposed concept consists of a reduction step and a phosphorus removal step. This paper will highlight some of the results with focus on the various metallurgical reactors used for slag reduction, including results from recently performed pilot trials using a DC furnace for cotreatment of metallurgical slags and other wastes.IntroductionToday, less than half of the produced LD-slag in Sweden is recycled to the blast furnace as a lime source and the rest is temporarily stored inside the steel plant. The steel slags cannot be used externally due to its content of vanadium and free lime. As the slag storage area is limited, this has become a problem for Swedish steel producers. The disposition of the slag is also a great waste of a valuable vanadium resource. The current potential value of vanadium in the discharged steel slag annually amounts to roughly US$ 100 million. Currently, Swerea MEFOS is conducting an 8-year vanadium recovery project called VILD (Vanadium in LD-slag) aiming at efficient recovery of vanadium and at the same time producing a useful slag product with low V-content. The project is financed by MISTRA - the Swedish Foundation for Strategic Environmental Research and the steel and mining industry in Sweden and Finland. Various reactors and process options have been tested in the past 7 years, from 3 kg laboratory scale, 150 kg induction furnace, 3 MVA pilot DC furnace, 5 MVA pilot AC furnace, 5 tons Kaldo furnace, to full scale direct hot slag reduction in the industrial site (12 tons of slag). This paper will introduce the VILD-concept and review the experiences gained from these trials. The advantages and disadvantages of the different options will be discussed and concluded."

Jan 1, 2012

By Afrodite Ntziouni, Vassilia Kasselouri – Rigopoulou, Athanasia Kyritsi, Konstantinos N. Pistiolas, Stamatia Gavela, Konstantinos Kordatos, Lazaros Iliadis

"The present study deals with the production and characterization of rice husk ash (RHA) and its use in the synthesis of zeolite of type ZSM-5. Rice husk was combusted in various temperatures with aim to find the suitable conditions for the production of amorphous silica. The resulted amorphous silica ash was then utilized as a starting material for the synthesis of ZSM-5 zeolite using the low temperature and atmospheric pressure process. The method led successfully to the synthesis of highly siliceous zeolite of type ZSM-5. The produced material was characterized using x-ray diffraction (XRD) and scanning electron microscopy (SEM).IntroductionRice husk is a major by-product of the rice-milling industries and it is usually used as a fuel for steam generation due to its high calorific power. During its combustion, rice husk ash (RHA) is produced. Knowing that the annual rice world production is over 615 million tons (2005), thus resulting in a potential production of more than 22 million tons of RHA [1], it can be understood that the RHA disposal is a crucial issue towards the environmental protection. However, due to the high silica content, RHA can be used as an alternative cheap source of silica for many uses, including as filler in polymers [2], concrete [3] and synthesis of zeolites [4-7].The burning of rice husk in air results in the formation of RHA with content in SiO2 that varies from 87 to 97% depending on the burning conditions, the rice variety, the climate and the geographic area [8]. Some small amounts of inorganic impurities are always present in the ash along with unburned carbon. The unburned carbon can be removed from the ash by further heating treatments in high temperatures, but this usually leads to the crystallization of the amorphous silica to cristobalite and/or tridymite [9]. The crystallization of the contained silica of the ash is also occurred when the burning conditions of husk are uncontrolled [10]. This crystallization is a disadvantage towards the preparation of silicon based materials, because the silica ash is rendered inactive in its crystalline form [11]."

Jan 1, 2008

By Susumu Okabe

The Mitsubishi Continuous Copper Smelting/Converting Process employs an electric furnace for settling the slag/matte mixture formed in the smelting furnace. In order to improve the separation of slag and matte and to minimize power consumption, the design and the operating conditions of the electric furnace should be optimized. As the first step, numerical heat and fluid flow analysis of the melts was carried out based on the distribution of current density and Joule?'s heat obtained by the electric field calculation. For these calculations, 3-D body fitted coordinate system and a finite volume method were applied. Using the developed numerical model, the flow pattern analysis by pulse input of a tracer element was simulated. It was found that a strong thermal convection of the molten slag exists around the electrodes due to the concentrated Joule's heat generation in a small area just under the electrodes, and this strongly affects the flow pattern in the furnace. The calculation results were compared with the data obtained from 'a plant test.

Jan 1, 1998

By S. Bagchi

The LaNi5-xMnx-hydrides have potential applications in cryocooling devices for non-mechanical method to compress hydrogen gas. Thermal aging behavior of LaNi5-xMnx-hydrides of compositions x=0.4 and x=1.5 has been investigated. The hydriding properties of the La1.02Ni4.6Mno.4 alloy do not change significantly after thermal aging at 453K for 260 hours. X-ray diffraction analyses of this aged alloy do not reveal the presence of any new phases but the Bragg peaks become broader. Line profile analyses show anisotropic microstrains with an average <e2>1/2 value of -5x103. Thermal aging of the other hydride, LaNi3.5Mn1.5 hydride, at 623K for 280 hours, showed significant disproportionation; the hydrogen capacity reduced significantly from an H/M value of 0.75 in the activated condition to -0.15 after aging. X-ray diffraction analyses showed disproportionated lanthanum dihydride, metallic Ni, and Mn phases. The Bragg peaks were very broad indicative of microstrains or small crystalline domains.

Jan 1, 1997

Copper and gangue mineralogy constitute the most critical parameters for the hydrometallurgical processing and cost-efficient extraction of copper. Minor changes in copper-, rock-, or alteration mineralogy can severely impact the comminution efficiency, curing, agglomeration, acid consumption, copper extraction and PLS impurity loading. Further, copper leach operations, particularly in the southwestern United States, are increasingly challenged by a combination of low grades and semi-refractory copper. This paper discusses the metallurgical and economical benefits of continuous mineralogical analyses in order to establish and operate a mineralogical data base in copper leach operations. Troubleshooting for copper extraction, integration of process mineralogy into production forecasting, and process optimization will be illustrated with operational experiences from Chile and the United States.

Jan 1, 1999

By Adolfo Pillihuaman, Alberto Nogueira, Cyro Takano, Marcelo Mourão

The organic household waste has a growing disposal problem, requiring costly disposal systems. It is necessary to find new applications for these materials; one could be the steelmaking raw material production. In this paper is studied the development of self-reducing pellets from the organic waste pyrolysis, where is generated carbon and condensable and non-condensable volatiles. Non-condensable volatiles were burned and condensable volatiles were recovered. The resulting tar was mixed with iron ore, coal powder and flux (CaO), to then be pelletized together. Compression, falls and tumbler tests were conducted to characterize the pellets before and after heat treatment and reduction processes. The reduction curve and their physical and morphological characterization were measured. The results were as was expected, the fluidized coal create sufficient adhesion that pellets earned resistance with an equivalent resistance of common pellets, showing a good feasibility of this process.

Jan 1, 2015

By Mokka N. Rao

In this experimental investigation, the principal operating parameters of the spirals HC 1870 and HG 8/7 are determined for the hydrogravimetric separation of the friable siliceous iron minerals of the Piar Distric, Venezuela. Mineralogical characterization including optical microscopy of feeding materials and the products after separation are presented. Comparative analysis is made of effectiveness of productivity between the two spirals.

Jan 1, 1999

By J. M. Tourre

Recently, interest in rare earth based oxide powders for electronic applications has risen dramatically. Considerable research has been devoted to the chemical synthesis of these compounds to improve the control of physical and chemical characteristics of the powder. In most cases, a high degree of homogeneity, purity and reproducibility is necessary in order to obtain good application properties. The synthesis parameters can control particle size, surface area, and morphology as well as the degree of homogeneity and application properties. Rhone-Poulenc, a world leader in the production of separated Rare Earth chemicals has developed a flexible process to produce a wide variety of compounds. The different processes for the synthesis of YBa 2Cu 3 O 7 will be discussed and compared to the RP process in term of product quality, cost and flexibility.

Jan 1, 1992

By Laurentiu Nastac

"This paper describes the development and validation of a comprehensive multiscale modeling approach capable of predicting at the mesoscopic scale level the ingot solidification structure and solidification-related defects commonly occurring during the vacuum arc remelting (VAR) process. The approach consists of a coupling between a fully transient macroscopic code and a mesoscopic solidification structure code. The predictions from the multiscale model, including grain morphology and size, primary and secondary dendrite arm spacings, Laves and NbC phases, tendency for freckling and columnar-to-equiaxed transition, were validated against experimental measurements for a 20-inch diameter VAR alloy 718 ingots. The validated model was then used to investigate the effects of melting rate and ingot diameter on the solidification structure of VAR processed 718 ingots.IntroductionThe objective of this work was to develop a fully transient multiscale modeling approach to get an insight into the effect of processing parameters on the cast micro- and macro-structure during VAR processing. The developed model assists in achieving better control of the ingot solidification structure and to determine trends in the macrosegregation in these ingots. Another objective of this work was to analyze the transient effects of production rate and ingot size on the resultant ingot microstructures. This objective was met by first understanding the effects of the full range of processing parameters typically used in the VAR process. Processing parameters such as power input and heat extraction rate significantly influence the ingot liquid pool size and shape as well as the ingot structure, which in turn will greatly impacts the final ingot quality."

Jan 1, 2012