Search Documents

By Tracy Morris, Weldon Read, Luis Navarro

"Bismuth is a recognized contaminant in the electrolytic refining of copper that can render many cathodes to be outside ASTM standards and unsuitable for copper rod and other downstream products if not carefully controlled. This paper portrays the performance of Molecular Recognition Technology (MRT) for bismuth removal at the Amarillo Copper Refinery (ACR) and describes how the highly selectivity gel has been successfully used to achieve good bismuth removal and how many pit falls and draw backs have been overcome.IntroductionASARCO operates one of the largest copper refineries in the world at Amarillo, Texas. The main feed for this refinery is produced at the Hayden smelter in Arizona. During the operation of this smelter a variety of metals are carried as impurities in the copper anodes because of the diversity of concentrates and residue products used as raw materials in the smelter feed mix. Even though the impurities are concentrated enough to be detected at the smelter, it is difficult to remove them completely. A simple way to control impurities at the smelter is to minimize the addition of material with a high concentration of impurities to the charge in order to reduce the output of this metal species. All this leads us to have a ""refinery problem"" [1,2,3]."

Jan 1, 2012

By R. A. Sharma

Neodymium metal was successfully produced by the reduction of Nd203 with Na in the presence of CaC12-NaCl melts by the overall reduction reaction Nd203 + 3 CaC12 + 6 Na ? 2 Nd + 3 CaO + 6 NaCl at -750°C. The metal produced was extracted from the salt media by dissolving it in a Nd-Fe alloy pool. The yield (percentage of theoretical neodymium produced) was found to depend on the salt composition and the mass ratio of salt to neodymium in the reactor. A yield of 95% was obtained with salt ratios as low as 3.5. Further decrease in the salt ratio below 3.25 decreased the yield. Stirrer position had little effect on yield; while increasing the temperature and placing fins in the reactor increased the yield. The Nd-Fe alloy produced was of as good quality as that produced using Ca reductant, and was suitable for direct use in producing General Motors MAGNEQUENCH? alloy for permanent magnets.

Jan 1, 1989

By Tracy Morris, Weldon Read, Luis Navarro

"During the leaching of anodic slimes, tellurium dissolves into the leach liquor together with copper and must be removed before the solution is sent to liberator cells for copper recovery. Prior to the installation of autoclaves, tellurium was precipitated using raw slimes that caused a recirculation of tellurium in the leaching circuit. After autoclaves were installed the old leach tanks were converted into tellurium reactors utilizing copper chips, steam and agitation to form a copper telluride precipitate. Tellurium levels of less than 10 rng/L are achieved in a timely manner.IntroductionThe electrolytic refining of copper consists of an electrolytic cell provided with an anode of impure copper, a cathode of substantially pure copper (starter sheet) and an electrolyte made of copper sulfate and sulfuric acid [1]. When a direct electrical current is passed between the anode and cathode inside the cell, the impure copper anode dissolves in the electrolyte and pure copper is plated onto the cathode. During this operation, many of the impurities are deposited on the bottom of the cell as an anodic slime residue composed of insoluble chemical compounds. Slimes are a major source of rare and precious metals in the copper industry [2-5],In the Amarillo Copper Refinery (ACR), the anodic copper slimes are sent to the Precious Metals department in order to extract and then refine the gold, silver, platinum and palladium from them. The remaining impurities, in the form of a soda slag or copper slag are sent to the Hayden smelter for further processing. Copper telluride is sent to the Selenium/Tellurium department inside the plant for selenium and tellurium recovery. During the leaching process of the anodic slimes, copper, tellurium, and other metal species in the slimes are dissolved into leach liquor that cannot be returned to the tankhouse unless the tellurium concentration is below 10 mg/L."

Jan 1, 2012

By Jan Steinhoff

The design options of a gravity separator are still limited and rely on the study of settling behavior. A methodology will be presented where an experimentally given inlet droplet size distribution (DSD) is the basis for the calculation of the dispersion layer in a gravity separator. A pilot-scale continuous gravity separator is presented and CFD (computational fluid dynamic) results are validated. A transmitted light measurement technique for the determination of the DSD is presented up to a holdup of 15% dispersed phase. The resulting DSD was in the range of 20–2000 μm depending on flow rate and phase ratio. Furthermore, correlations of the real DSD with the settling behavior of the dispersion in a settling cell are discussed. The new approach to the description of gravity separators will be presented and the applied CFD methods showed good results with the system water/paraffin.

By Anurag Tripathi, J. K. Saha, S. K. Ajmani, J. B. Singh

"The quality of steel is a major concern in the metallurgical industry. The control of liquid steel temperature can enhance the level of cleanliness in steel. Ladle is one of the major vessels used to transfer liquid steel between different stations. The heat transfer phenomenon taking place in this vessel needs to be monitored for controlling the liquid steel temperature. A CFD model was developed for prediction of liquid steel temperature during complete process cycle of ladles in direct heats. The model was validated with liquid steel temperature measured at on-line purging station and tundish during teeming from one of the actual steel plant. The accuracy of model was 96 %. The results obtained show insignificant effect of slag thickness, tapping temperature and ladle life on liquid steel temperature in the ladle. However, the importance of initial refractory temperature was noticed. The CFD model developed in present work can generate the thermal history of liquid steel and refractory walls of any ladle at any stage.1. IntroductionThe control of liquid steel temperature is desired to achieve required steel quality. The low casting temperature is detrimental and may result in nozzle blockages due to premature solidification in the tundish. The phenomenon of heat losses taking place in ladles needs to be understood for prediction of liquid steel temperature. The assessment of thermal profile of liquid steel from BOF converter to caster can be done through consideration of heat losses at all points. Hlinka and Miller [1] showed that the ladle pouring temperature varies due to heat losses from molten steel into surrounding refractory layers. The phenomenon of thermal stratification was numerically simulated by Ilegbusi and Szekeley [2]. The effects of slag cover on heat loss and liquid steel flow in ladle before and during teeming to a continuous casting tundish was numerically simulated by Chakraborty and Sahai [3]. Investigators also developed some simple models to predict the steel temperature for some of the processes taking place in ladles [4-9].The present work is an effort to generate the full information about the temperature drop taking place in any ladle throughout its process cycle. This information can be used to predict liquid steel temperature and to take decisions to minimize heat losses."

Jan 1, 2012

By Jingbo Liu, Zhimin Wang, Wenchao Li

"IntroductionThe advantages of non-stoichiometric perovskite material are highlighted in many papers[l]and many of this family of materials are well-suited to integration into microsensor devices. Among them, barium titanate is the most promising due to it's piezoelectric, pyroelectric, dielectric properties. Through modification, BaTiO3-based materials can be utilized in many kinds fields, such as surface wave probe; pholoconducting devices, field-effect transistor, permanent memory permanent storage, and ultrasonic transducerl2-3l. In this Paper, a series of BaTiO3-based polycrystals were synthesized by sol-gel processing which appears to be a very promising method for the manufacture of ceramic, because it offers significant advantages such as high purity, chemical homogeneity, controlled particle sizes of ceramics, and lower processing temperatures [4]. In a sol-gel process, alkoxides of the constituent elements show different reactivity toward water so that the preparation of multi-component homogenous system is difficult. In the experiment, inorganic salt was substituted for some of the alkoxides. Acetic acid which is employed for the solvent and catalyst, acts as donor ligand to titanium alkoxide and controls, the hydrolysis polycondensation reaction. Taking these aspects into consideration, we select the system Ba(OAc)2, , La(OAc)3, Ti(O11Bu)4 and acetic acid which is used as both solvent and homogeneous catalyst for the first time.ExperimentalA series of La3+-doped BaTiO3-based nano-crystals were prepared with sol-gel technology using various parameters. The precursor solution was prepared in the presence of barium acetate, lathanium acetate, and titanium tetrabutoxide monomer in butyl alcohol. According to the flow chart (fig. I.), Ba(OAc)2, La(OAch dissolved in the glacial acetic acid (0. lmol/40ml) in a three-neck flask were mixed with a solution of titanium tetrabutoxide monomer in butyl-alcohol(l 7ml/20ml) at room temperature and under constantly, vigorous stirring conditions. In most cases, the resultant solution was golden yellow and stable in the air. To this precursor solution, containing Ba, La, Ti in the desired ratio, water was added incrementally for hydrolysis under continuous stirring until sol was formed. After aging for more than 2 hours, sol was transformed to gel at room temperature. If heated during aging, the gel was formed in a shorter time. The wet gel was allowed to dry at 50°C for more than 10 hours. The dried gel was transparent or light yellow. In order to obtain BaTiO3-based nano-crystals, the amorphous dry gel was calcined at 600°C, 700°C, 800°C, 900°C, 1000°C respectively[5]. The ceramic humidity sensor was formed through the cold-pressed, aged, capsulated routes. The dried gels were crushed in an agate mortar and then pressed into discs of ? 1.5 X l.5mm (l.5mm diameter and l.5mm thickness), then held at about 16.5 MPa pressure for 3 min [6]. The disc was sintered at 1350°C and 1400°C for I hour respectively. During the processing, an Ag-Pt electrode was inserted in the sensor [7]. (See the flow chart.)"

Jan 1, 2000

By V. K. Kalyani

The present paper discusses a three layer feed forward artificial neural network (ANN) model, trained using the error back propagation algorithm, has been established to simulate the column flotation circuit used for beneficiation of Sillimanite. Parameters such as superficial air velocity, wash water rate, froth height, % solid, feed velocity, sodium silicate and oleic cid are considered as process operating variables and % yield of Sillimanite is the output of the experiment. The results from the ANN modeling, involving the non linear relationship between inputs and outputs, indicate good agreement with experimental observations. The network model validates the experimentally observed trends. The optimal model parameters in terms of network weights have been estimated and can be used for computing parameters of the process over wide-ranging experimental conditions.

Jan 1, 2006

By R. Moreau, V. Uspenski, K. Messadek, Y. Delannoy

Experiments and numerical simulations have been carried out to investigate the properties of quasi-2D turbulence. A new mercury model experiment has been built and tested in a uniform magnetic field up to 6T, (Ha~ 1000), ensuring a better two-dimensional behaviour than earlier versions (Alboussiere et al., 1997), limited to 0.2T. The quality of the experimental results has been improved in order to get wave number spectra (instead of frequency spectra) and higher signal over noise ratio (due to the higher magnetic fields). In parallel, some two-dimensional "direct" numerical simulations were performed using a commercially available code to solve a 2-D motion equation involving a source term to model the Hartmann layer. This term is derived from the condition of closure of the electric current, which allows to transfer the Hartmann effect into the 2D-core flow without simulating the layer itself (Sommeria & Moreau, 1982). No subgrid scale modelling is needed in such a two-dimensional situation where most of the energy is carried by the large scales.

Jan 1, 1999

By Li. Jiarong, Zuojian Liang, Qingyan Xu, Baicheng Liu, Shizhong Liu, Hailong Yuan

Single crystal solidification of turbine blades is a key technology for the production of reliable and high efficiency gas turbines. The solidification process of single crystal investment castings causes a number of problems that have to be solved such as the increase of casting defects and complexity of production process. Computer modeling and simulation is helpful to predict the defects and improve the process design. In the paper, a mathematical model for three dimensional simulation of solidification and single crystal growth of investment castings was developed based on CA, mechanism of crystal growth and basic transfer equations such as heat, mass transfer equations. Many factors including constitutional undercooling, curvature undercooling and anisotropy, which had vital influences on microstructure evolution, were considered in the model. Temperature, crystal growth interface and structure defects of investment castings of single crystal superalloy were investigated at withdrawal rates of 4.5mm/min and 7mm/min. Simulated results showed that microstructure evolution and structure defects were predicted reasonably and calculated results were coincident with experimental ones. The study indicated that three dimensional solidification simulation technique is a powerful tool for understanding the fundamental of solidification and the formation of structure defects in single crystal investment castings and finally for optimizing process design.

Jan 1, 2004

By L. B. Tsymbulov

Sulphide melts formed in the course of smelting of nickel and copper-nickel feed (matte) actually are sulphide-metallic melts since sulphur contained in the melts is in deficiency with respect to metals. The level of metallization is rather relevant feature of sulphide melts and is widely used in calculating material and heat balances for pyrometallurgical processes. Despite of the above parameter? importance, the investigators have no single opinion on what should be understood under metallization level and the method of its determination. In the present study we present the results of our own experimental and theoretical researches that have allowed determination of some mechanisms of sulphide melts? crystallization. Based on the mechanisms revealed new scientifically justified approach has been offered for determining level of metallization of the components present in sulphide melts. It has been demonstrated that sulphur distribution between the melts is substantially different from generally accepted concept.

Jan 1, 2006

By Rumen Markov, Lubomir Kuzev

"The treatment technologies for municipal solid waste (MSW) are effective mainly for components sized over 40 – 50 mm. This fraction is separated by screening in the beginning of the process. Usually the undersized product is deposited without additional treatment. Its quantity is variable from several up to 30 – 40 % of the total MSW. Both oversized and undersized fractions are formed by all types of primary matter. Adapted technologies from mineral processing will provide a suitable technology for treatment of MSW under 40 – 50 mm. The MSW content depends on the geographical location, the degree of urbanization and other factors. The methods can be applied for separations of different components suitable for recycling or other utilization are: • Separation by density; • Separation in thin liquid layer; • Selective grinding and screening; • Flotation, etc. Introduction Municipal solid waste (MSW) represents an integral part of public urbanization. However, there are some drawbacks stemming from MSW, in regard to its collection, transport and elimination. Different approaches exits worldwide for tackling the problems arising from MSW. For a short period of time, the attitude towards MSW has evolved in several levels, each further level being characterized by higher percentage of utilization of MSW components. Thus, the bottom line has been shifted from safety storage towards processing that includes recycling and maximal utilization of MSW components. Technologic processes applied for treatment of MSW have a common feature – that the fine components, having sizes under 20 mm, 30 mm, 40 mm, or 50 mm are excluded from treatment process trough screening, and in most cases diverted without any additional treatment to preliminary prepared storage sites. MSW in Sofia – current situation The amount of MSW collected daily in Sofia as around 1000 t/24 h. It is stored or baled. Baling is a spare alternative of storage, since baling insures only temporal keeping of MSW, till the building of suitable storage site where the bales will be transported and buried. The morphologic composition of MSW in Sofia has been determined several times at different time intervals, from some Bulgarian organizations as well as from the Japanese organization JICA. So far, however, there is still a lack of enough systematical and comprehensive study. Generalized results from the studies on the MSW components, as well as some important parameters are given in Table 1."

Jan 1, 2008

By Varadajan Seshadri

The increase in production of continuous casting machines requires long ladle sequences without interruption. Very often the production schedule has to accommodate a variety of steel grades. In such cases downgrading may be inevitable. Models must be made available to study the alternatives that would make possible mixing of steels in the tundish but minimizing the losses due to downgrading the slabs. Physical modeling was used to evaluate the influence of variables such as internal geometry of the tundish, presence of turbulence inhibitors, depth of ladle long nozzle, weight of steel in the tundish, steel throughput upon the tundish transition curve. Expressions for minimum residence time and transition period have been determined. Mixing-transition is allowed to continue inside the liquid pool in the mold and the final solute distribution in a given cross section is captured by a solidification model. The result is a map of the transition in the final product.

Jan 1, 2006

By Xian-Dong Zhou, Guo-Sheng Sun, Jianzhong Luo, Hong-An Guan

"Oxygen utilization rate of the pretreatment process which adopts biological contact oxidation method for slightly polluted supply water is relatively low, less than 10%, usually lower than 3%. So the aeration amount is not determined by calculated value of oxygen demand when doing process design, but by the ratio of gas and water. The aeration way of the biological pretreatment process for slightly polluted supply water was introduced in this paper. In the foundation of the principles of mass transfer kinetic theory and experimental data, the change law of DO (dissolved oxygen) and ammonia in the aeration tank was analyzed to explore aeration method which will help to improve the overall effectiveness of handling capacity.IntroductionThere are many kinds of filler used in the biological contact oxidation process, such as flexible solid filler, composite filamentous filler, powdery clay filler, particle ceramic filler and so on. Regardless of the different forms of filler, there are a couple of common points in the function of the aeration[1,2]: (1) The aeration process in biochemical tank not only provides adequate oxygen for the biological reaction, but also plays as a role of stirring water; (2) Biochemical reactions mainly happen in the upper reaches of tank, but seldom at down-streams.This paper, from the perspective of changing aeration way, discussed the feasibility of improving the effectiveness of biochemical reactions without increasing aeration amount, which would have some leading significances for the operation and management of similar projects."

Jan 1, 2008

Electrocrystallization studies were conducted in a concentrated acid-copper electrolyte to determine the influence of chloride ions and glue on copper nucleation and on the structure of thin copper layers. Electrochemical experiments allied to SEM and XRD examination were performed to characterize the mechanism of nucleation in the presence of additives at 65°C. Results indicated that most of the copper nucleation from a 83 g dm-3 Cu2+ solution, with 140 g dm-3 of H2SO4 is achieved in a matter of milliseconds, Although the presence of chloride and glue, at the concentration levels tested, does not seem to substantially modify the nucleation mechanism, the morphology, nuclei density and the copper film structure and orientation are changed by the presence of additives and by electrolyte stirring.

Jan 1, 1999

By Tang Mo-tang

A new process for extracting indium from indium-zinc concentrates was proposed in this paper. The process can directly extract indium from removed copper solution by P204, and cancel the stage of removing iron in the traditional process because of using iron and part of zinc in the In-Zn concentrates for direct preparing high quality Mn-Zn soft magnetic ferrites. The technologies in the processes, such as leaching the neutral leached residues with high concentrated acid at high temperature, reduction ferric and removing copper, and extracting indium, were investigated. The results showed that total recovery ratio of indium has been increased from less than 70% in the traditional process to more than 95%. This process has the advantages of largely simplifying the procedure of indium extraction, zero draining off of iron residue and zero emitting of SO2. So this is a clean production process.

Jan 1, 2006

By E. A. Román

An ion exchange pilot plant, provided by Mesco Inc., was tested for antimony control in the electrolyte at three Chilean tankhouses for copper electrorefining: Chuquicamata, Potrerillos and Enami -Ventanas. The pilot plant, with a nominal extraction capacity of 1.2 kg Sb/day, worked connected to both experimental and commercial circuits, performing a total of 310 loading and elution cycles. An innovation in this process is the use of a chelating organic elution reagent, which presents some advantages over the traditional 6N HCI. This new eluent is amenable to continuous regeneration and recycling with high recovery efficiency. Antimony removal starting at initial, concentrations of 0.5 to 0.6 g/l of Sb down to steady concentrations of 0.1 to 0.0.6 g/l Sb, resulted in the production of High Grade copper cathodes with Sb contents below 0.1 ppm. Anodic slimes showed Sb contents below 1%.

Jan 1, 1999

By Eiki Ono, Atsushi Yamatodani, Shigeru Sunagawa, Yasushi Takasaki, Atsushi Shibayama, Yasunori Higuchi

"During metallurgical processing of non-ferrous metals, smelting residue (inc. smelter slag, flue gas and so on) is inevitably generated as secondary product.In this research, some experimental feasibilities were investigated to recover/remove Cu and As from the residue. Primarily, the removal of As and volatilized materials from the residue was examined by pyrometallurgical treatment (dry-process). In the second stage after treating the residue with a dry-process, leaching and solvent extraction as hydrometallurgical treatments (wet-process) were also investigated by using H2SO4 solution as a two stage leaching treatment, to dissolve various metals from the leach residue. Then, solvent extraction was examined by using LIX-84I as an extractant to recover and separate Cu from impurities from the final (2nd) leached solution. For the leaching stages, the removal of 90 % As and the leaching rate of 85 % Cu could be achieved by 0.25 mol/l and 1.0 mol/l H2SO4 solution, respectively. On the other hand, the extraction of over 90 % Cu and stripping was carried out by solvent extraction. 1. IntroductionIn metallurgical process for non-ferrous metals, smelting residue (inc. smelter slag, flue gas and so on) is inevitably generated as secondary product, i.e., flue dust, slug and so on. The smelting residue includes some useful metals and undesired toxic materials; Cu, Pb, Ca and As, etc.In Japan there is one undisclosed place stockpiled with 10,000 ton of smelting residue from abandoned smelters about 25 years ago. Therefore it is necessary to reduce the residual amount for space and environmental protection including water treatment by separating and removing toxic materials."

Jan 1, 2008

By B. J. Jody

This paper describes a one-step thennal-treatment process, developed at Argonne National Laboratory, to remove all organic contaminants from the glass-fiber waste that is generated during the glass-fonning process. The recovcred glass fibers can then be recycled into new glass fibers or new glass products without adversely impacting the operations of the glass industry or the quality of its products. Our process involves shredding the waste to a manageable size and then processing it at temperatures below its melting point to remove the polymeric-coating layer. The glass industry generates more than 60,000 tons of glass-manufacturing waste annually in the glass-forming process alone. Recycling of this waste stream can keep this non-biodegradable waste out of the landfills. In addition, use of recycled glass lowers energy costs, by an average of about $5 per ton as compared to using virgin raw materials to make virgin glass fibers. This process will also reduce the emission of C02 by 17,400 tons a year and it will also reduce the emission of nitrogen oxides. Economic analysis of our process shows a potential payback of less than 2 years.

Jan 1, 2003

By Hiroshi Nakazawa

An acid mine drainage in abandoned Horobetsu mine in Hokkaido, Japan, contains arsenic and iron ions; total arsenic ca.10ppm, As(III) ca. 8.5ppm, total iron 379ppm, ferrous iron 266ppm, pH1.8. Arsenic occurs mostly as arsenite (As (III)) or arsenate (As (V)) in natural water. As(III) is more difficult to be remove than As(V), and it is necessary to oxidize As(III) to As(V) for effective removal. 5mL of the mine drainage or its filtrate through the membrane filter (pore size 0.45m) were added to arsenite solutions (pH1.8) with the concentration of 5ppm. After the incubation of 30 days, As(III) was oxidized completely with the addition of the mine drainage while the oxidation did not occur with the addition of filtrate, indicating the microbial oxidation of As(III). In this paper, we have investigated the microbial oxidation of As(III) in acid water below pH2.0.

Jan 1, 2006

By Tiffany Brown

In the thiosulfate gold leaching process, thiosulfate is used to complex gold following electrocatalytic oxidation of the native metal by Cu(II)-ammines. Unfortunately, Cu(II) complexes also catalyse the undesirable conversion of thiosulfate to polythionates. We have been seeking alternatives to ammonia, which fulfil the role of ammonia but minimize thiosulfate decomposition. One aspect of these studies has involved the determination of the rate of thiosulfate oxidation by the Cu(II) complexes from UV-Visible spectral changes. Various ligand classes, including pyridyls, polyamines, aminocarboxylates and picolinates, have been tested and the majority found to inhibit thiosulfate decomposition. Interesting variations in reactivity with the nature and denticity of the ligand and L/M ratio have been observed. In the case of open chain polyamine ligands with 2 to 5 nitrogen donors, the rate of thiosulfate oxidation was generally found to decrease with the denticity and the concentration of each ligand. Saturation of the Cu(II) coordination sphere appears to inhibit the oxidation of thiosulfate when excess thiosulfate is present. The Cu(II) complex of the branched polyamine ligand, tris(2-aminoethyl)amine (tren) exhibits this behaviour in excess thiosulfate. Interestingly, when the [Cu(tren)(OH2)]2+ complex is in excess oxidation of thiosulfate was observed. This unexpected finding prompted a spectrophotometric study of this reaction which has revealed that the oxidation of thiosulfate involves several processes, two of which involve the formation and decay of a tetrathionate radical.

Jan 1, 2003