Search Documents

By George H. Davis

The Caribou sulfide deposit near Bathurst, New Brunswick (Figure 1) is illustrative of one variety of strata-bound sulfide deposits. It consists of numerous near-vertical sulfide lenses which are concordant to the foliation and lithologic layering of low-grade metamorphic host rocks. Pyrite is the chief mineral in these lenses, but appreciable quantities of sphalerite, chalcopyrite, and galena are also present. Rocks in the Caribou mine area belong to the Tetagouche Group of Ordovician age. They consist chiefly of (1) quartz-sericite and quartz- sericite- feldspar schists, (2) greenschists, and (3) slate and phyllite. The trends of these steeply dipping rocks define the trace of a tight, steeply plunging fold structure, the Caribou fold (Figure 2). This fold plunges approximately 750 to the north-northwest; its axial plane strikes N.20°E. and dips steeply westward. Sulfide lenses of the Caribou deposit are associated spatially with the Caribou fold. The deposit is located in the fold along the contact between quartz-sericite and quartz-sericite-feldspar schists on the hanging wall and quartz-chlorite-sericite phyllites and graphitic schist on the footwall (Figure 3). Genesis of the Caribou deposit is ambiguous because its strata-bound form suggests syngenetic sulfide deposition, whereas its location within a fold suggests structurally controlled epigenetic mineralization. Acceptability of a particular genetic model rests on establishing the time of mineralization relative to deposition, deformation, and metamorphism of the associated rocks. To establish the timing for Caribou mineralization, the deformational histories of rock and sulfide, respectively, were compared. Epigenetic and syngenetic models can be tested against this interpreted structural history of the Caribou deposit.

Jan 1, 1971

By Frederic Souche, Andrew R. Klaetsch, Brian Hann, Nick Goodenow

This paper describes support of excavation (SOE) design and construction for three large diameter shafts excavated through glacial soil and controlled blasting in complex sedimentary rock formations. SOE in soil consists of unreinforced secant pile rings designed to resist lateral pressure in circumferential compression, eliminating costly steel core beam reinforcing. Controlled blasting at the shafts, adits, and tunnels in densely populated neighborhoods requires managing risks to the public, buildings, and utilities. Controlled blasting approaches limited adverse impacts to receptors nearby while achieving adequate production and fragmentation. A site-specific observational approach was used to adjust blasting parameters, limiting the impact on local stakeholders while maintaining daily progress and managing overbreak.

Jun 13, 2023

By Chris Ashton, Andreas Rädle, Taner Aydogmus

"The Contract C310 is part of the current biggest infrastructure project of Europe “Crossrail” which is a major new cross-London rail link project and comprises the construction of the North Woolwich Portal, Plumstead Portal and the twin tube Thames Tunnels with a length of approximately 2.6km. Two Mix-Shield TBMs (Diameter 7.12m) were driving through differing challenging ground conditions (Thanet Sand, Gravels, Flint and Chalk) below the ground water table. The two tunnels were underpassing several listed buildings, sensitive structures, operational railway tracks with low overburden and close to existing subway tunnels in an urban environment. Several additional measures as compensation grouting, micro piles and an intensive monitoring has been carried out to ensure a safe tunnelling process. PROJECT OVERVIEW CROSSRAIL Project Crossrail Crossrail is currently the biggest infrastructure project in Europe which has been developed to serve London and the southeast of England. The project includes the construction of twin-bore tunnels on a west-east alignment under central London and the upgrading of existing National Rail lines to the east and west of central London. The new rail track, as shown in Figure 1, starting in Shenfield/ Abbey Wood in the east of London and ending in Reading / Heathrow Airport in the west of London, includes the construction of nine central area stations, providing interchange with London Underground, National Rail and London Bus services, and the upgrading or renewal of existing stations outside central London.Altogether there will be 118km of new rail tracks, including 42km of tunnels and 40 train stations. After completion in 2018, Crossrail expects 200 million passengers per year (Tauriainen, Rädle, Ingram 2013)."

Jan 1, 2016

By Erik S. Bernard

"INTRODUCTION Reinforced Concrete (RC) members such as beams and columns are usually required to include stirrups to maintain post-crack shear capacity, and some may include stirrups that act as confining steel to maintain structural integrity during a seismic event (eg. NZS3101, ACI 318). To achieve seismic resistance, the spacing between stirrups is usually required to be much closer than is ordinarily prescribed for non-seismically resistant structures. Each stirrup must also fully enclose the longitudinal reinforcement with long end-hooks to ensure that the contained concrete is sufficiently restrained during reverse-cycle loading and the reinforcing bars are confined to prevent buckling. The close spacing between stirrups can lead to congestion of reinforcement within members, and can also be expensive to construct due to the labor-intensive nature of steel fixing. A possible alternative to closely-spaced stirrups is the use of fibers to provide restraint and confinement during a seismic event, although this is not yet recognized in codes. Previous experimental research (Jiuru et al, 1992; Filiatrault et al, 1995; Bayasi and Gebman, 2002; Billington and Yoon, 2004) has demonstrated that steel fibers are relatively effective in this application, but suffer the problem that their stiffness can make them difficult to consolidate within an already tight reinforcement cage, especially if they are relatively long (>40 mm). Moreover, steel fiber reinforced concrete (SFRC) is subject to embrittlement with the passage of time, leading to a steady loss of ductility beyond crack widths of 1-2 mm (Banthia and Trottier, 1994; Bernard and Hanke, 2002; Bernard, 2014; Bjontegaard et al, 2014; Bernard, 2015). Since cracks during seismic events are generally much larger than this, embrittlement may present a challenge to the long-term efficacy of SFRC during seismic events. An alternative to steel fibers for enhancement of seismic resistance is the use of macro-synthetic fibers. This type of fiber usually offers the advantage of being flexible so that consolidation is easier between reinforcing bars. They also offer superior durability compared to steel fibers and can reduce flexural crack widths (Bernard, 2016). Several recent small-scale investigations (Ma et al, 2012; Carnovale, 2012; Osorio et al, 2014) have indicated that macro-synthetic fibers can produce meaningful improvements in seismic resistance if used in combination with conventional steel reinforcing bars. The present investigation has extended research in this field by examining whether embossed macro-synthetic fibers can be used to increase the spacing between stirrups while maintaining seismic resistance."

Jan 1, 2016

By P. Semberg, B. Bjorkman, C. Andersson

"In this study, the interaction between magnetite and the additive olivine was studied after oxidation as well as after isothermal reduction at temperatures in the 500º-1,300º C range. In the olivine sample, the forsteritic olivine particles react partly during the oxidation pretreatment to form magnesioferrite and vitreous silica along the particle corona. This breakdown of the olivine particles during oxidation liberates magnesium from the particles, which do not react until temperatures of above 1,150° C in reducing atmosphere. When the hematite in the sample is reduced, and when the temperature is high enough to allow solid-state diffusion at ~800º C, the magnesium of the magnesioferrite redistributes, so that the magnesium concentration approaches the same level throughout the iron oxide structure. For magnetite, this did not occur until 800° C. At 1,000° C, this magnesium reacts further with the silica in the glassy slag phase, which crystallizes into fayalitic olivine. At this temperature, the magnesium has diffused over distances of more than 600 µm from large olivine particles after 2 hrs reduction. From this point, the primary slag phase in the pellet, until melting, is solid fayalite. Upon reduction to metal, the metallization front concentrates the MgO in the remaining wustite, which can lead to MgO levels of up to 10 mole% locally. The melting point of the fayalite is raised from 1,145º C to a melting range of 1,238-1,264º C due to the MgO increase, as estimated based on phase diagrams, which were adapted to the pellets tested. Much of the olivine that remained unaltered in the oxidation process will be encapsulated by iron before the particles begin to dissolve in reducing conditions and, therefore, plays no role in the reduction before final melting of the particles occurs.IntroductionEnvironmental concerns have placed increasing pressure on the CO2-intensive iron and steel industries to further optimize operation toward higher productivity and more efficient use of reducing agents. At the same time, high demand for iron ore has caused new iron ores with lower grades and more complex chemistries to be taken into production. In Scandinavia, the main iron-bearing material is magnetite-based pellets with olivine, which allow operation with very low slag volumes and, hence, lower fuel rate ( Slagnes and Sundqvist Ökvist, 2008; Hallin et al., 1994). Both the MgO and SiO2 of the olivine, as well as the elements of the gangue of the ore, i.e., Si, Mg, Ca, Al and alkali, interact with the iron oxides to give the finished pellet product its final properties in the blast furnace. Tailoring the additive mix to be used for a certain iron ore for optimal product properties, therefore, requires detailed knowledge of the mechanisms by which these elements dissolve and react in the pellet."

Jan 1, 2015

By Greg Colzani, Emily Thompson

The 3RPORT Project, includes a 5-mile tunnel excavated by a 19-foot diameter slurry Tunnel Boring Machine below the city of Fort Wayne, IN. The Geotechnical Baseline Report (GBR) indicated vuggy to massive argillaceous dolomite within the tunnel alignment. During excavation of the first reach, the TBM encountered zones of cohesive clay and sandstone presented in full face and mixed face conditions. The occurrence of Sandstone was not a “Baselined Condition” described in the GBR for this reach of the alignment. This paper will discuss the methodology to investigate, mitigate and evaluate the DSC impacts on TBM performance.

Dec 1, 2022

By Yanxu Shen, Cheng Liu, Zhijie Chen, Hao Chen, Huimin Gao, Zijie Ren

Fluorite, a kind of critical non-metallic minerals, is the primary source of industrial fluorine. Sodium oleate (SO) is commonly used as the collector of fluorite ores. However, because of its some features (such as the low solubility, high solidifying point, and poor dispersion of SO) at low temperatures, it profoundly inhibits its collecting ability as well as the flotation performance. Herein, we have developed a low-temperature-resistant collector for the efficient flotation separation of fluorite from quartz. The advantages and disadvantages of the SO and sodium petroleum sulfonate (SPS) were analyzed by comparing the performance under different temperature conditions. The results of flotation tests suggest that SPS exhibited much better collecting performance than SO under low temperature. The flotation mechanism of the two collecting agents were further analyzed by contact angle measurements, zeta potential measurements, Fourier-transform infrared spectroscopy (FT-IR), and flotation kinetics. The results indicated that both collectors can selectively undergo electrostatic and chemical adsorption with fluorite, with no adsorption on quartz surface. The sulfonic acid group in SPS is a hydrophilic functional group, which has a relatively higher solubility in water. Therefore, the water solubility of SPS is better at low temperatures.

Sep 30, 2021

By T. J. Lutz, S. Gallagher, J. R. Srednicki, J. J. Sammarco

The Illuminating Engineering Society of North America reports that an underground mine is the most difficult environment to illuminate (Rea, 2000). Researchers at the U.S. National Institute for Occupational Safety and Health (NIOSH) Office of Mine Safety and Health Research (OMSHR) are conducting ongoing studies designed to explore different lighting technologies for improving mine safety. Underground miners use different visual cues to escape from a smoke-filled environment. Primary and secondary escapeways are marked with reflective ceiling tags of various colors. Miners also look for mine rail tracks. The main objective of this paper is to compare different lighting types and ceiling tag colors to differentiate what works best in a smoke-filled environment. Various cap lamps (LED and incandescent) and lasers (red, blue, green) were compared to see which options resulted in the longest detection distances for red, green and blue reflective markers and a section of mine rail track. All targets advanced toward the human subject inside of a smoke-filled room to simulate the subject walking in a mine environment. Detection distances were recorded and analyzed to find the best cap lamp, laser color and target color in a smoke environment. Results show that cap lamp, laser color and target color do make a difference in detection distances and are perceived differently based on subject age. Cap lamps were superior to lasers in all circumstances of ceiling tag detection, with the exception of the green laser. The incandescent cap lamp worked best in the simulated smoke compared to the LED cap lamps. The green laser was the best color for detecting the tags and track compared to the red and blue lasers. The green tags were the easiest color to detect on the ceiling. On average, the track was easier for the subjects to detect than the ceiling tags.

Jan 1, 2013

By W. K. Choi

Using electrochemical techniques it was demonstrated that bioleaching of gold from refractory pyritic ores is a complex phenomenon. Many intermediate electrochemical reactions were found to be involved in the oxidation of pyrite, using cyclic voltammetry and carbon paste-pyrite containing electrode. Furthermore, the oxidation process was controlled by solid-state diffusion as suggested by chronoamperometric and chronopotentiometric measurements. Using the Sand's approach, the activation energy of solid-state diffusion was found to be = 22.4 kJ. After bioleaching, 96% gold was extracted from the leach resi¬due with a thiourea solution in 1 hour. A generalized model for the mechanism of pyrite oxidation has been presented.

Jan 1, 1990

By Roberto L. Romero

The dressing of Bolivian tin ores has been done up to the present by classical. gravity methods, taking advantage of the high specific gravity of cassiterite compared with that of the accompanying gangue. For this purpose, jigs and shaking tables are used in the treatment of the various size fractions in which the ore is classified. Bolivian ores are mainly of the vein type and, to obtain a reasonable separation, crushing and several stages of grinding are necessary during the process to substantially liberate the cassiterite from the gangue. Gravity processes for cassiterite are effective for sizes down to 200 mesh. Below this size the efficiency of the gravity methods falls off very rapidly with increasing fineness of the mineral grains. The conventional treatment for this material is desliming followed by tabling on shaking tables various other types of machines have been designed for the gravity treatment of these fine particles but they have had limited success. Bolivian ores contain an appreciable amount of minus 200 mesh material constituted by "primary fines" caning from the mine itself, and "secondary fines" originated during the crushing and grinding necessary for liberation of the difficulty in the treatment of these fine particles is one of the causes why the recovery of tin in concentrates is only of around 50% in the mines owned by Corporacidn Minera de Bolivia, the State owned enterprise. The average figure for other Bolivian mines is

Jan 1, 1971

By T. Grammatikopoulos, C. Gibson, M. Aghamirian

"Lithium is a silver-white alkali metal that has recently become a target commodity for many junior mining companies. Lithium has a wide range of applications including ceramics and glass, lubricating greases, air treatment, continuous cast mold flux powders, polymer production, and primary aluminium production, but the current popularity of lithium can be attributed to an anticipated increase in demand for lithium ion batteries. The most common lithium-bearing minerals occur globally in pegmatites and granites. Spodumene [LiAl(Si2O6)] is the most desirable economic lithium-bearing mineral due to its high lithium content (theoretical Li2O content of about 8 wt%). However, lithium can also be hosted in petalite, micas, tourmaline, and phosphate minerals. In Canada there are a number of spodumene deposits in Ontario and Quebec at development stage that have the potential to help narrow the forecast lithium supply gap stemming from the widespread acceptance and use of electric vehicles. This paper discusses the beneficiation of hard rock lithium deposits, including an in depth review of the use of flotation to upgrade spodumene. A review of the use of dense media separation (DMS), magnetic separation, and roasting as means to process spodumene bearing ores is also discussed. INTRODUCTION Lithium is a soft, silver-white alkali metal with atomic number 3. As of 2015, the end use of lithium was estimated to be as follows: lithium-ion batteries (35%), ceramics and glass (32%), lubricating greases (9%), air treatment (5%), continuous casting mould flux powders (5%), polymer production (4%), primary aluminium production (1%) and other uses (9%) (Jaskula, 2014). Lithium is found in brine lake deposits containing lithium chloride and in hard rock pegmatite deposits. It can be sold in a range of product types; as mineral concentrate, brine, compound (lithium carbonate or lithium hydroxide) and metal depending on its intended end use (Goonan, 2012; Jaskula 2014). In the 1990s the United States and Chile were the largest producers of lithium globally, primarily from brine operations (Ober, 1994). Most of the lithium compounds produced over this period were consumed in the glass, ceramics and aluminium industries. In the 1980s and 1990s there were two major lithium operations in the United States: brine operations at Silver Peak, Nevada, and a spodumene mine and lithium carbonate/lithium hydroxide plant in Kings Mountain, North Carolina. The Kings Mountain operations ceased production in 1991 and were eventually dismantled in 1994. Brine operations were also active in Argentina and Chile, while the largest lithium ore deposit in the world was operated at Greenbushes, Western Australia. During this period it was predicted that major shifts in demand for lithium would come from the success and widespread use of electric vehicles (Ober, 1994)."

Jan 1, 2017

By Richard L. Sanford

The generalized rail haulage simulator described in this paper is an outgrowth of the need to expand a previously developed single level simulator to permit analysis of production problems where intermediate car storage is used. Many of the ideas of the former single level simulator, which is an integral part of an Underground Generalized Materials Handling Simulator (UGMHS), have been used in model development. In addition, experience gained in applying the earlier model to a variety of operating conditions has been heavily relied on. The generalized rail haulage simulation model can operate as an independent system and, as such, can be used to analyze rail haulage systems using production distributions as data input. In addition, this model is designed to replace the present rail haulage sub-assembly in the UGMHS model and the linking procedure has been integrated into the model. The flow of coal from production sections in UGMHS, for example, fill the mine cars and a condition of no empty cars at a loading station will shut down in by production systems.

Jan 1, 1974

By Umay Cinarli, Ahmet Turan

High-energy consumption in primary aluminum production (from bauxite ores) makes secondary aluminum production (from metallic raw materials such as scrap and dross) very critical. Aluminum dross, as a waste, arises in pyrometallurgical processes, and it is the mixture of metallic Al, Al2O3, other metal oxides, metal halides, and some other compounds like AlN. Aluminum dross has two subgroups (white and black) with respect to its metallic aluminum content. White dross is a secondary aluminum resource because of its high metallic aluminum content, whereas black dross, having low metallic aluminum content, is generally disposed in dumping areas. In the present study, it was aimed to develop a simple technique to valorize aluminum black dross in the form of alumina-based ceramic materials through pyrometallurgical (calcination) and hydrometallurgical (leaching) operations. Moreover, thermochemical simulations were conducted by using HSC Chemistry 6.12 software to simulate calcination conditions. After leaching experiments, an alumina-based ceramic containing approximately 36.8% Al2O3, 61.4% MgAl2O4 with 1.8% Na2FeO4, which might be available to use as a spinel refractory in steel smelting furnaces, was obtained in the experiment carried out in a solution containing 10 mLH2SO4 and 40 mL distilled water (3.5 M). Moreover, the sinterability of the alumina-based ceramic was investigated at the temperatures from 1350 to 1550 °C. In the sample which was sintered at 1550 °C, a density value of 3.15 g cm−3 and a hardness value of 69.58 HV were measured.

Oct 26, 2020

By T. P. Weldum, W. Conger

"These studies address the relationship between mill media sizing and its grinding efficiency. Starting with the results from a review of the literature, the issues of initial media sizing for a new ball milling circuit, and then optimal media sizing for an existing milling operation, were studied. The Functional Performance parameters “Mill Grinding Efficiency” and cumulative “Mill Grinding Rates” from both plant and test-scale equipment were used, and provide valuable new insight into this topic. A plant media sizing diagnostic tool is presented, as are newly developed testing equipment and evaluation methods, and recent case studies. REVIEW OF MEDIA SIZING LITERATURE For a plant metallurgist to answer the question “How can I maximize plant profit by manipulating this grinding circuit variable?” she must know what effect the variable has on grinding circuit efficiency. Despite the significant cost of grinding media and its potential effect on production capacity, the ‘best’ media sizing remains ill-defined for any given ball mill circuit in the industry today. The underlying reasons for this will be discussed. But the importance of this issue drove Metcom and its industrial partners to take on the challenge of how to engineer the ball charge for an existing grinding circuit. In the absence of any proven method, the first step was a review of the literature. Sponsored by Cleveland-Cliffs, Inc., a broad review of the literature was undertaken, producing “The Effect of Media Sizing on Ball Milling Efficiency” (McIvor, 1997). Among hundreds of publications that were reviewed that discuss the topics of media sizing or wear, forty-five were studied in detail. These were grouped into: plant experiences; laboratory and pilot plant investigations; media wear studies; population balance modeling studies; and general papers on ball milling which included the topic of media sizing. The reader is encouraged to refer to that review. The findings remain unchanged, although some relevant papers have been written since (e.g. Staples et al, 1997; Banasi et al, 1999; Orford et al, 2006; LaMarsh, 2015). The main findings of the review were as follows."

Jan 1, 2018

By G. ALBORNOZ, S. Utili, A. AGOSTI, C. VALDERRAMA, R. PELL, N. Morales

The steepness of the slopes of an open pit mine has a substantial influence on the financial return of the mine. The paper proposes a novel design methodology where overall steeper pitwalls are employed without compromising the safety of the mine. In current design practice pitwall profiles are often planar in crosssection and the profile in between ramps especially tend to be planar and defined by a constant inter-ramp angle. Sometimes rock layers exhibiting different strengths require the inclination of the profile to vary with depth, but the inclination across each layer is usually constant. Here instead, a new geotechnical software, OptimalSlope, is employed to determine optimal pitwall profiles of depth varying inclination. OptimalSlope seeks the solution of a mathematical optimization problem where the overall steepness of the pitwall, from crest to toe, is maximized for an assigned lithology, geotechnical properties and Factor of Safety (FoS). Bench geometries (bench height, face inclination, minimum berm width) are imposed in the optimization as constraints which bind the maximum local inclination of the sought optimal profile together with any other constraints such as geological discontinuities that may influence slope failure. The obtained optimal profiles are always steeper than their planar counterparts (i.e. the planar profiles exhibiting the same FoS) up to 8 degrees depending on rock type and severity of constraints on local inclinations. The design of a copper mine is first carried out employing planar pitwalls, secondly adopting the optimal pitwall profiles determined by OptimalSlope. The adoption of optimal slope profiles leads to a 34% higher net present value and reductions of carbon footprint and energy consumption of 0.17 Mt CO2 eq and 82.5 million MJ respectively due to a 15% reduction of rockwaste volume.

Mar 2, 2022

By Frank Agyemang, Zainab Nasrullah, Richard LaDouceur, Mehran Saddat

To sustain the circular economy, defence applications, and other renewable technologies, recycling rare earth elements (REEs) and other critical elements from their secondary resources is important. This cause has resulted in rigorous research and development for viable extraction and separation of REEs. Previously, Sm-Co recycling has been done with technologies, which fall under the categories of pyrometallurgy, physical separation, and hydrometallurgy. All these methods have limitations associated with energy, cost, and environment. Reportedly, the chemical leaching technology has successfully recovered and separated Sm-Co. Still, it has limitations associated with slow mass transfer and leaching kinetics, and there is a need to intensify the process to make it time efficient. This approach has also adversely impacted the environment by an extensive use of toxic, corrosive, non-selective, and expensive reagents. In this research study, chemical leaching of Sm-Co was performed using this new class of solvents, Deep Eutectic Solvents (DESs), which fall under the category of ion metallurgy. Four different DESs were used, proven to be green, non-toxic, biodegradable, cheap, and selective for cobalt over samarium by 82% leaching conversion. To improve the slow mass transfer and leaching time, this new technology of resonant vibratory mixing (RVM) was also tested. RVM intensifies mixing by establishing near instantaneous, low energy mixing conditions through resonance. It has been shown to improve the adsorption kinetics and was tested for the leaching kinetics. Four combinations of DESs were prepared, which are made up of two quaternary salts: Choline Chloride and Tetra Butyl Ammonium Chloride, and three organic compounds: Oxalic Acid, Urea, and Ethylene Glycol. These combinations were used for chemical leaching of Sm-Co with leaching factors of time, temperature, and type of DESs. After leaching, the samples were tested with and without resonant vibratory mixing with conditions of time, intensity (%), and type of DESs. Samples were analysed with Induced Coupled Plasma - Optical Spectroscopy (ICP - OES). Future work will involve a life-cycle assessment to assess the RVM technology with other conventional mixers, and an extensive study of DES properties to improve selective leaching.

Feb 1, 2025

By Wang Hongwei, Wu Yongping, Cao Peipei, Jiao Jianqiang

Fully mechanized top caving mining of steeply inclined extra-thick seams with variable angles has complex roof rock movement, failure, caving, and filling mechanisms. Moreover, the variable-angle coal seams make rock–equipment stability control challenging. We analyzed rock deformation and failure mechanisms, overburden bearing structures, and working characteristics of supports through physical simulations, field tests, and theoretical analysis of the no. 120210 working face of Zaoquan Coal Mine. Overburden rock movement has distinct regional characteristics, with a large caving height (to the main roof layer) in the upper area, and lower caving height (to the lower main roof) in the lower area. Support loading is regional and unbalanced along the inclined direction. The critical layer of overlying strata migrates, and bearing structures formed by breaking the critical layer exhibit cross-layer generalization along the inclination. The upper region has a cantilever beam structure in the basic roof rock layer; the lower region has an inclined masonry structure with multistage ladders in the breakage basic roof rock layer. Application of a false-inclined working face layout with the tailgate ahead of the headgate and an arc arrangement (radius 28.65 m, arc length 10–20 m) in variable angle areas, and regional control of support working resistance and top-coal caving amounts, control regional failure overburden. Safe and efficient mining was achieved, with the monthly production and recovery rates reaching 344,900 t and 85.86%, respectively. Our results expand the scope of fully mechanized top caving mining and have important theoretical and technological significance.

Nov 23, 2020

By J. M. Wempen, R. D. WEYHER, M. K. McCarter

Beam theory is a proxy for the behavior of intact, deforming roof strata above underground openings. Strong, stiff, intact strata have the ability to store significant strain energy when underground openings have large spans, as is typical of longwall operations. When strata fail, they may release some or all of this strain energy. Released energy is partitioned between fracture, thermal, and seismic energy. The tensile failure surface in simply supported beams is predicted to be free of shear stress. This prediction and the kinematic inability of crack slip during fracture make significant dissipation of energy by friction unlikely. In this study, the failure energy partitioning of Nugget Sandstone specimens is examined. Tensile fractures in specimens were induced using three-point loading tests. Elastic waves emanating from fracture events were recorded using an array of accelerometers. Accelerometers were placed within two crack lengths of the fracture surface, and the acceleration records are similar to strong motion seismic records. Spectral analysis was performed and used to develop synthetic, well-behaved, acceleration signals. Synthetic velocity signals were used to estimate radiated seismic energy generated by fracture. These estimates of radiated seismic energy demonstrate a potential means to constrain the minimum seismic partition. Fracture testing was performed on additional samples to estimate the fracture toughness of the sandstone. Synthesis of this data demonstrate a potential means to constrain a maximum seismic partition. Bounding the seismic partition for this type of fracture event could aid the detection and evaluation of seismicity emanating from longwall operations. Having better information about the location and magnitude of mining-induced seismicity within longwall overburdens could lead to better understanding of extraction sequencing and rock behavior in general. These energy estimates also support the hypothesis that dissipation of thermal energy by friction is small in bending tensile failure.

Jul 1, 2020

By Rudolph K. Hoagberg

Silica sands, primarily in coarse size ranges, are used to prop open fissures or voids created in the bedrock by hydraulic fracturing. This procedure increases the flow of gas or oil or other fluids through the bedrock. The sands used must meet various specifications relating to their physical and chemical characteristics; these characteristics are in turn related to the geologic provenance of the sand deposit. The Jordan Sandstone, a Cambrian formation which is exposed in Minnesota and Wisconsin, meets the specifications of a proppant sand by virtue of its depositional history and its sedimentary properties.

Jan 1, 1980

By J. T. Tanner

The research activities of the Minerals Research Laboratory, which is a part of North Carolina State University, is normally confined to solving beneficiation problems, and developing flotation processes for the mining industry. In recent years the laboratory has veered from its main purpose somewhat and has placed some emphasis on the manufacture of products from mineral concentrates. This has been the result of requests for help from industry. One such request came to the MRL from a talc producer in North Carolina who was having a difficult time competing with foreign imports of steel marking crayons. He felt that if a process could be developed whereby a satisfactory crayon could be produced from powdered talc at a low cost that he could compete.

Jan 1, 1986