Search Documents

By Y. F. Hou

This paper reports the results of the study of the influences of concentration and modulus of sodium potassium silicate solution (Na-K activator) and curing mode on the phase composition, mi-crostructure and strength development in the geopolymers prepared using Class F fly ash. X-ray dif-fraction (XRD), Fourier transform infrared spectroscopy (FTIR) and MAS NMR are utilized in this study. It shows that the compressive strength increases while sodium potassium silicate solution modulus increases, but when modulus exceeds 1.7, the compressive strength decreases, and it decreases markedly while modulus is greater than 2.0. The compressive strength improves with increase of sodium potassium silicate solution concentration. When the concentration is 36%, the compressive strength reaches the maximum. Elevated temperature can increase the strength of samples synthesized using sodium potassium silicate solution with 32% concentration and modulus 1.2. Compared to the strength of the sample cured at 50?, the strength of the samples cured at 65? and 80? are higher at 1 day and 3 days, but when cured at 80?, strength is smaller than that cured at 50? for 7 days. When temperature is too high, too long curing time will decrease the strength. Long precuring at room temperature before application of heat is beneficial for strength development, and there is about 10%~50% increase in strength of the samples cured at 1 day precuring and 2 days elevated temperature as compared to the strengths of the samples cured for 3 days at elevated temperature or cured for 28 days at room temperature. The main product of reaction in the geopolymeric material is amorphous alkali aluminosilicate gel.

Jan 1, 2014

By R. Shiva Kumar, G. E. Sreedhar, Rajan Kumar, K. Suresh, A. K. Aketi Veera, M. Narasimha, P. S. Jodan

"In most of the coal washeries, Dense Medium Cyclone’s (DMC) are deployed to treat coarse coal fraction in the range of 50-0.5 mm. DMC’s are very popular due to its ability of high tonnage, ease of operation and effective separation at high near-gravity material (NGM) in feed coal. The ease or difficulty of washing is merely depending on the NGM fraction present in run of mine coal. However, the quantitative effect of NGM on DMC performance was not explored in the literature. Hence, in this investigation, the influence of NGM on DMC performance is focused. With the help of synthetically prepared coal mixture, the effect of NGM mass fraction on separation efficiency is studied in three different approaches. Firstly, by increasing the NGM coal fraction systematically from low to as high as possible; second by varying the distribution of NGM coal; and third by varying distribution of particles lying just above and below the near-gravity zone. Washability studies are also carried out to establish the theoretical yield for the prepared synthetic mixtures. Pilot-plant experiments are carried out in a 4-inch DMC with 1.4 operating separation density treating coal in the size range of 4 - 0.5 mm. From results, the partition curves are constructed by both density and size wise distributions. It is observed that at higher NGM coal fraction i.e above 60%, the performance of DMC is very poor with significant coal particles misplacement. In second approach with increased distribution at higher density fractions, the separation efficiency reduces. In third series the distribution of fraction in near-gravity zone doesn’t much effect the separation except the shift in separation density. It is observed that smaller size (-0.5 mm) coal particle having high NGM content seems have a profound effect on DMC performance leading to significant fines misplacement to wrong products."

Jan 1, 2018

By Jie-Liang Wang, Yongdan Cao, Zhao Cao

"The effect of ethylenediamine tetraacetic acid (EDTA) on flotation separation of fluorite from bastnaesite and its selectively depression mechanism on fluorite were studied by single mineral flotation, artificial mixed minerals flotation, solution chemistry analyses, Zeta potential and XPS measurements.The results show that fluorite can be deeply depressed by EDTA while the flotation of bastnaesite is almost unaffected when octanohydroxamic acid (OHA) is used as a collector. The separation index (SI) between bastnaesite and fluorite increases with the dosage of EDTA, SI can be raised from 1.18 to 12.66 when EDTA dosage increases from 0 to 2×10-3mol/L.Solution chemistry analyses show that EDTA is able to convert the Ca(OHA)2 hydrophobic precipitation on fluorite surface to a soluble Ca-EDTA complex but cannot complexly dissolve the Ce(OHA)3 precipitation on bastnaesite surface. Therefore, the Zeta potential of OHA conditioned fluorite can be reduced significantly by EDTA while the reduction degree to Zeta potential of bastnaesite is relatively low. XPS measurement shows that EDTA removes the chemically adsorbed OHA from fluorite surface but has little effect on the adsorbed OHA on bastnaesite surface. As a result, fluorite can be selectively depressed by EDTA in bastnaesite flotation, which behaves an important industrial application prospect in rare earth ore flotation.INTRODUCTIONNowadays, Rare earth elements (shortened as RE) and compounds are of significant importance for a range of rapidly expanding industrial applications including catalysis, metallurgy, renewable energy, and special materials due to their unique electrical, magnetic, optical and chemical properties [1]. The seventeen RE elements, including the lanthanide-group fifteen elements, yttrium and scandium, could be divided into three groups, i.e., light, medium and heavy RE elements based on the different solubility of RE sulfates [2]. Bastnaesite ((Ce,La)CO3), containing approximately 75% REO, is one of the most important light RE minerals [3]. Flotation is the common method to recover basetnaesite [4-6]. Nonetheless, basetnaesite is often associated with calcium-bearing gangue minerals such as fluorite, and the separation of basetnaesite and fluorite by flotation is usually difficult due to their similar surface properties and therefore floatability [7-9]. Therefore, research on high selective flotation reagents of bastnaesite over gangue minerals has attracted a lot of attention [10]."

Jan 1, 2018

By F. Boylu

In this study, Ca-bentonite was subjected to a series of systematic hydrocyclone tests with the aim of developing separation procedures and in turn achieving optimum recoveries. In hydrocyclone tests, vortex and apex diameters and also feed pressures were investigated. In each hydrocyclone set, vortex diameter was kept constant while the other two parameters varied to produce bentonites con-centrates of various smectite contents. The separation efficiencies were evaluated based on the cation exchange capacity (CEC), particle size and swelling index. The detailed hydrocyclone tests showed that, upgrading of Ca-bentonites require procedures different from the bentonites reported in the literature. Sodium and mixed bentonites are easy- to-disperse and easy-to-separate whereas calcium types need to be scrubbed rigorously for disintegration. Scrubbing properties of ca-bentonite were investigated as a function of scrubbing time and percent solids by weight (PS). The scrubbing conditions at 700 rpm for 1.5 hours and percent solids of 30 % were found more effective for achieving a better quality bentonite. In addition to the parameters mentioned above, the effect of percent solids on hydrocyclone separation was also studied. Although Ca-bentonites permit studying at higher percent solids, increasing solids content of the pulp deteriorated the quality of the clean products. Application of an appropriate separation scheme enabled the development of a unique separation procedure involving stage wise scrubbing followed by hydrocycloning which yielded calcium bentonite concentrates with CEC of 90 meq/100 g and high swelling indexes of 12 mL from the original bentonite of 65 meq/100 g and 7.0 mL, respectively. These results indicate that upgraded bentonite products can be conveniently used in various diverse industrial applications including bleaching earth, desiccant, cat litter, paper etc.

Jan 1, 2014

By N. Jovanovic, A. Vazirizadeh

"The main objective of this study is to find a solution to design a mass flow observer system with the minimum required sensors and maximum observability for a mineral processing plant. The second objective is designing a mass flow observer configuration with high reliability to manage sensor failures. This configuration will provide a robust monitoring system that increases plant availability and process measurement fault detection. Furthermore, the monitoring system is expected to improve process efficiency. In this investigation, the procedure of designing an observer system is presented along with three models to design the sensor network. The advantages and disadvantages of each models are discussed and finally the models result for an industrial case are presented and analyzed. INTRODUCTION The concepts of observability and redundancy of mass flow are directly linked with the ability to solve and estimate the mass flow. There are hundreds of streams in a process plant flowsheet, and for technical and economic reasons it is not possible to measure all mass flows. It is thus important to know for a set of measured streams, which of the unmeasured streams can be estimated. The concept of observability deals with this issue. It is also valuable to know whether a measured mass flow of streams can be estimated even if a sensor fails for some reason. Redundancy deals with this failure question. A stream is said to be observable if it can be estimated by using the measurements and/ or mass conservation equations. Also, a stream is redundant if it is observable even when its measurement is removed. Observability and redundancy analysis can be exploited for adding new measuring instruments. It can also play a useful role in efficient decomposition and data reconciliation problem (Narasimhan and Jordache 1999). The value of an observer system cannot be justified without considering its benefits. This justification is done through evaluation of data reconciliation, gross error detection and improving process performance such as outlined below:"

Jan 1, 2018

By W. M. Zeng

A mixed culture of moderately thermophilic microorganisms was enriched from Acid Mine Drainage (AMD) samples collected from several chalcopyrite mines in China,which can leach copper from chalcopyrite effectively. Its tolerance to chalcopyrite was brought up to 80 g/L after being adapted to gradually increased concentrations of chalcopyrite. The effects of several leaching variables on copper recovery in Stirred Tank Reactor had been investigated. The ore contained chalcopyrite (62.2%) and galena (25.6%) as the main sulfide minerals. The results of the tests show that it is possible, operating at 8% of pulp density to attain copper extraction of 75% in 44 days. The leaching rate of chalcopyrite tends to increase with the dissolution of total iron. Microscopic counts of microorganisms in the solution tend to be higher at low pH range. Furthermore, the analyses of leached residues indicate that the passivation of this chalcopyrite is mainly due to the formation of a mass of jarosite and anglesite (about 48.3% and 21.7% in residue respectively), other than elemental sulphur layer. The bacterial community composition was analyzed by using amplified ribosomal DNA restriction analysis (ARDRA). Two moderately thermophilic bacteria species were identified as Leptospi-rillum ferriphilum and Acidithiobacillus caldus, with different proportion in the bio-pulp, 67% and 33%, respectively.

Jan 1, 2014

By Gaurav Soni, Roe-Hoan Yoon

A first principle flotation model has been derived from the basic mechanisms involved in flotation. The model consists of a series of analytical equations for bubble generation, bubble-particle collision, attachment, detachment, and froth phase recovery. The model can predict flotation from both hydrodynamic and surface chemistry parameters such as bubble size, particle size, energy dissipation rate, ?-potentials, contact angles (?), etc. The model predictions have been compared with the results of a series of laboratory flotation tests conducted using mono-sized glass beads of different particle sizes and contact angles under different operating conditions. Some of the experiments were conducted using a 1:9 mixtures if hydrophobic silica and hydrophilic magnetite, so that the product graded could be readily determined by simple magnetic separation. The model predictions are in good agreement with the experimental results both in recovery and grade. A computer simulator developed on the basis of the model is capable of designing a preliminary flotation circuit on the basis of feed characteristics, e.g., size-by-liberation data, and the hydrodynamic information on the flotation cells to be incorporated in the circuit.

Jan 1, 2014

Copper nickel separation is performed by mineral processing techniques both pre and post smelting in Copper Cliff at Vale Canada?s Operations. The separation at Clarabelle Mill takes advantage of the ore mineralogy to affect a separation on the rougher concentrate where chalcopyrite and pentlandite exhibit high liberation and high recoveries thus their separation is simple although incomplete. The copper concentrate comprises only 50% of the copper in ore with the remaining copper being separated post smelting in the Matte Separation plant where the slow cooled Bessemer Matte is again treated by mineral processing operations using flotation to separate the chalcocite and heazlewoodite and magnetic separators to remove a metallic nickel alloy. This paper discusses the mineralogy, separation processes and work currently underway to improve the separation of copper from nickel in these plants.

Sep 1, 2012

By K. Haga

In this study, flotation tests were performed to investigate behavior of enargite and chalcopyrite ores from different sources synthetically mixed for separation of enargite. Flotation parameters including; pH, reagents concentration and type and flotation time were controlled to obtain an enargite concentrate with high As and chalcopyrite concentrate and final tailings with As content below 0.5 mass%. The copper ore bearing enargite mineral contained 5.87 mass% As and 16.50 mass% Cu while the chalcopyrite bearing ore contained 0.32 mass% As and 21.63 mass% Cu. The two ore samples were mixed at 7:3 (enargite: chalcopyrite) by weight ratio to prepare a mixed ore sample with arsenic content at 3.16 mass% and 18.25 mass% Cu for the flotation study. For enargite single ore flotation, the 38?75 µm size fraction showed that over 98% enargite was selectively recovered within 5 min at slurry pH of 4.0 and arsenic content in the final tailings was reduced to 0.22 mass%. In mix ore (enargite+chalcopyrite) flotation, 97% of enargite was first removed at pH 4 followed by chalcopyrite flotation at pH 8, and over 95% recovery was achieved in 15 min flotation time. Arsenic content in the final tailings was reduced to 0.1 mass%.

Sep 1, 2012

By G. B. Abaka-Wood

"The versatility of froth flotation has made it vital in the beneficiation of rare earth elements (REE) minerals from either high or low grade ores of complex mineralogy. There has been a significant increase in the tonnage of rich iron oxide tailings obtained from extraction of primary commodities such as copper and gold in Australia, which have been identified to have very low grade rare earth oxides (REO) (= 1%). There is a vast knowledge gap in the upgrade of REO from such tailings. The aim of this research is to investigate the feasibility of the use of fatty acids for the upgrading of REO from selected iron-oxide rich tailings. Two forms of fatty acid collectors (oleic acid and sodium oleate) were employed in this investigation. Bench scale flotation tests were carried out using a Denver D-12 cell.The effects of pulp pH, fatty acid dosage, particle size distribution (-150 +75 µm, -75 +38 µm and -38 µm) and conventional depressants (sodium silicate and starch) dosage on flotation recovery of REO were investigated. A comparison of the flotation results indicated that sodium oleate was the more efficient fatty acid for REO flotation at all the pulp pH investigated. The flotation performance is demonstrated to be particle size-dependent. The results on the effect of depressants dosage indicated that both sodium silicate and starch were unselective in reducing the recovery of hematite (Fe2O3) and quartz (SiO2) with corresponding decrease in REO recovery. Generally, Fe2O3 and SiO2 formed substantial contents of the flotation concentrates obtained, both in the absence and presence of depressants, which indicates liberation is a major challenge in achieving selective REO upgrade and recovery.The flotation tests carried out on the iron-oxide rich tailings suggest the possibility of REO upgrade using fatty acids, although particle size distribution and minerals liberation are key limiting factors in achieving selective REO upgrade and recovery."

Jan 1, 2018

By Y. C. Liu

Arsenic bearing copper-gold ores deposit have been found in most areas of China, especially in southwest. Due to the very closed association between arsenic, copper and gold, conventional flotation and cyanide leaching process may not give positive results. An arsenic bearing copper-gold ore in Sichuan province ,with gold grade of 10.12 g/t, 0.6% Cu and 0.14% As, is characterized by superfine grains with -40 microns fraction accounting for 70.9% and the gold enwrapped mainly by pyrite and tennanite accounts for 34.31%. Arsenic in this ore occurs in isomorphism, deposited in tetrahedrite. The ore was processed primarily in two stage flotation to get copper bearing gold concentrate and pyrite bearing gold concentrate respectively, and sequentially processed by leaching. Under the pressure of 300 KPa and 110~115 ?, the copper-gold concentrate was leached by an oxidizing and catalyzing leach agent then copper and gold were separated from each other in leach solution. The pyrite bearing gold concentrate was processed by cyanide leaching with the leach residue as sulfur product. The test results showed that copper recovery was up to 88.89%, gold recovery up to 89.18% and sulfur recovery up to 92.64%.

Jan 1, 2014

By N. V. Ramana Murthy

Utilisation of Low-Grade Iron Ore Fines after concentration not only helps in conservation of the mineral wealth, but also substantialsly improves the economics of iron ore mining. There has been need to develop suitable beneficiation process for upgradation of low-grade iron ores towards their rational utilisation. Presently the circuit adopted for processing iron ores has limitations in reduction of alumina. The depletion of high-grade reserves, utilisation of low-grade reserves coupled with in-creasing market pressure for improved product quality necessitates re-examination of the process flow sheets and evaluate alternative or supplemental processing routes. The main objective of the Process amenability studies for utilisation of Low-Grade Iron Ore Fines (-10mm) is to get Pellet grade concentrate with +65% Fe (min), SiO2 1.8% (max), Al2O3 1.8% (max) and other proportionate constituents by adopting suitable beneficiation techniques and to collect the relevant data (Quality and Quantity of the Products) for the process development. In an effort to formulate a conceptual process flow sheet, the Process amenability studies for utilisation of Low-Grade Iron Ore Fines (-10mm), which is lying at a mine site in India, samples were collected and taken up for the study. The efforts of R & D of NMDC are discussed in this paper. Low-Grade Iron Ore Fines (-10mm) sample assayed 60.10% Fe with 3.48% SiO2 Aland 4.48% 2O3from 40 microns to 300 microns. The sample consists of hematite as the chief ore mineral followed by minor amounts of maghemite. The gangue minerals include quartz and ferruginous clay in which quartz occurs as medium grained where as ferruginous clay occurs as fine to sub microscopic size mineral. The economical processing route evolved out of the studies finally could yield a final concentrate constituting 58.63% by weight along with Iron unit?s recovery of 63.51% assaying 65.10% Fe with 1.48% SiO2 and 1.85% Al2O3route that adopted comprises the following operations. Making slurry in a sump pump followed by grinding in close circuit with 48mesh size Screen. The -48 mesh size product was subjected o the Cycloning to remove slimes. The Cyclone Underflow product was subjected to Floatex Density Separation (FDS) to separate fine heavy minerals from the gangue minerals. The FDS Underflow was collected as concentrate. The FDS Overflow product was further subjected with Wet High Intensity Magnetic Separation (WHIMS) to recover more Iron units as magnetics. A conceptual process flow sheet was evolved, which may become the prelude to the subsequent finalisation of the process flow sheet for commercialisation.

Jan 1, 2014

By V. Sheikhzadeh, M. Saghaeian, R. Hejazi, A. Abazarpoor

"The morphology of pellet feed is known to influence several properties of iron ore pellets, including drop number, compression strength and reduction properties. The effect of grinding method on the particle size, specific surface area and particle shape of an iron ore concentrate has been studied. Grinding methods considered were ball mill and high pressure grinding rolls (HPGR). 5 different samples (Blaine= 1800, 1900, 2000, 2100 and 2200 cm2g-1) were used to compare the size, shape and specific surface of particles for each grinding methods. Particle size was meticulously examined by sieve analysis, laser sizing and image analysis. In samples ground by ball mill, it has been observed that the fraction of particles <10µm increases from 39% to 46% as the Blaine number increases from 1800 to 2200 cm2g-1. For HPGR samples, corresponding figures are 41% and 49% respectively. It is evident that for samples ground by HPGR, the fraction of fine particles is higher than that of those ground in the ball mill. To measure the specific surface area of particles, Blaine and BET were used. A higher real surface area was observed from HPGR treatment in comparison to ball mill grinding, provided by a higher porosity, cracks, roughness and new surfaces. Shape factor of particles was determined using three descriptors: circularity, roughness, and aspect ratio. It was also observed that particles produced by HPGR were more elongated, less circular, and rougher than those processed by the ball mill. 1. INTRODUCTION Particle size and shape are important parameters that can significantly affect mineral processing plants and pelletizing plant performances (Brozek and Surowiak, 2007). It has also been proposed that green pellet quality is directly related to the amount of fine particles in a pelletizing plant (Dwarapudi et al., 2008; Umadevi et al., 2008; Gul et al, 2014; Van der Meer, 2015). Particle size distribution and specific surface area (SSA) are also key factors that can control the quality of green and fired pellets. Processing circuits generally reduce the fines fraction to lower than the required specific surface area (SSA). It is therefore necessary to regrind concentrates to produce suitable pellet feed for further treatment in the balling and firing steps [1, 2]. Two main methods are used for re-grinding of concentrate; high pressure grinding rolls (HPGR) and ball mill. Given the different forces used to reduce size in these methods, it is expected the shape of particles will be different (Pourghahramani and Forssberg, 2005)."

Jan 1, 2018

By B. K. Saikia

A preliminary attempt has been made to study the particle size distribution (PSD) of minerals in one of the industrially important pulverized Indian coal sample using computer-controlled scanning electron microscopy (CCSEM). The results show that clay minerals, quartz, pyrite, and pyrrhotite form the bulk of the mineral matter. Minor minerals, such as calcite, dolomite, ankerite, barite, oxidized pyrrhotite, and gypsum are also observed in the coal sample. The PSD of the included minerals is generally observed to be finer than that of the excluded ones in the coal. Thus, the coal rich in included minerals has more small mineral particles, which may affect its reactivity. The proportion of included to excluded is found to be higher in major cases. Si is found to be mostly occurred as quartz and clay minerals, while Al mostly occurs as silicate minerals. Fe is primarily present as iron sulfides, iron oxide, and Fe-Al-silicate. S is partitioned into iron sulfides and gypsum. Most Ca occurs as carbonates and gypsum, with a minor fraction associated with clay minerals. Mg is found to be mainly present as dolomite and clay minerals, with a very minor fraction present as ankerite. The majority of alkali elements are associated with aluminosilicates. P is mostly associated with kaolinite and/or present as more complex compounds containing Al, Si, and other elements as apatite are found to be absent in the coal studied. Ti is mainly present as rutile and kaolinite. The geo-chemical association of the trace elements has also been discussed. Keywords: minerals, Assam coals, Indian coals, CCSEM study

Sep 1, 2012

By Ritva Tuunila, Antti Häkkinen

"Wet stirred milling is one of the most effective grinding methods in producing very fine powders in large scale production, but it is a very energy-intensive process, especially when pigments or even nanosize particles are produced. Therefore, optimization of the process parameters is important. The specific energy consumption is a function of stress energy, which describes the effect of tip speed and media characteristics on grinding, and is related to the number of stress events during milling. In effective grinding, a large number of stress events are necessary. The stirrer configuration influences the number of stress events and their intensity, because the motion of the media and the suspension are caused by a rotating stirrer. The effect of three different stirrer types: a pin, disc and blade stirrer, on the grinding rate, i.e. product fineness and specific energy were investigated in this study with a batch laboratory stirred mill with two tip speeds. The material used in the experiments was calcium carbonate. The results obtained with the smaller tip speed showed approximately similar grinding rates and energy consumption for all stirrer types. When looking in closer detail, the blade stirrer seemed to give the finest product with all grinding times compared to the pin and disc stirrers, which both produced almost the same product fineness with the same grinding times. The specific energy consumption was the smallest with the disc stirrer, but not very big differences were obtained. With a higher tip speed, greater differences occurred both in grinding rates and specific energy consumption. The blade stirrer was the most effective in grinding, and the pin stirrer the next. The net energy consumption for the blade and pin stirrers was almost the same, but it was slightly higher for the disc stirrer."

Jan 1, 2014

By D. P. Chakraborty

Joda East Iron Mine, one of the captive iron ore sources of Tata steel, located in the state of Odisha in eastern India caters to approximately 45% of the iron ore requirement of the Jamshedpur Steel Plant. The iron ore occurring in the mine having high in iron content along with high in alumina. Clay and gibbsite are the predominant mineral phases present as surface coating, fracture filling and/or free occurring and are responsible for alumina content higher. Alumina in iron ore impacts the techno-economic performance of a steel plant by impacting sintering and blast furnace productivity. The impact is even higher when it comes to fine ore used in the blast furnaces in the form of sinter as it constitutes a major portion of the blast furnace burden. Therefore, it is beneficial to upgrade iron ore in the mine head and to reduce alumina before it is subjected to agglomeration. Mineralogical test works reveal, that alumina in iron fines is mainly associated with the clay attached to the hematite particles, either free or interlocked to a very fine size. The paper describes the efforts made to reduce alumina in the iron fines in Joda East processing plant, without much of capital investment for a very sophisticated fines beneficiation circuit. In this process, a suitable dispersant was added in the plant that dispersed the masked slime coating over the iron ore fines, thereby making a better quality iron ore fines with reduced alumina content. The alumina in fines improved by 0.2 units? means from a label of 2.4-2.6 % reduced to 2.2-2.4 %. With this initiative, not only the primary objective of alumina reduction is met but also it has given substantial benefit in reduction of silica and as well as moisture in product. This moisture reduction also has given bottom line impact by reducing idle freight and royalty.

Sep 1, 2012

By Kari Niiranen

LKAB (Luossavaara-Kiirunavaara AB) is operating iron ore mines, concentration plants and pelletizing plants in Northern Sweden. The largest of the apatite magnetite deposits and the mines are Kiirunavaara with annual production rate of approximately 27 Mt crude ore underground. LKAB produces two varieties of pellets: blast furnace pellets and direct reduction pellets (LKAB DR Oxide Pellets). Meanwhile the concentration process in a sequence of the low intensity magnetic separation (LIMS) and flotation at the concentration plant. In spring 2007 there were noticed great fluctuations of SiO2 grade in the crude ore. The high SiO2 grade is particularly problematic in the case of direct reduction pellets. In consequence, a project was started (called Silica in the Mine) to define exactly the problem related with silica and to find out, if possible, the reason for the great fluctuation of SiO2 grade in the crude ore going to the processing plant. A further target of this project was to develop a simplified method at the laboratory scale, to predict SiO2 grade in the magnetite concentrate in the future, but also predict the physical properties of the ore with respect to mineral processing. The essential stage of systematic characterization of the ore body for mineral processing properties is the estimation and simulation of different parameters from the laboratory scale to the large scale at the concentration plants using empirical data collected at the mineral processing by LKAB in Kiruna. Further a target was also to find useful physical parameters for mineral processing and implant those parameters into the existing geological 3D-model of the deposit. This information will be used for making prognosis of the future mining and the quality of the crude ore. It will also give better control and improve the production planning in the mine and the performance at the concentration plant in Kiruna concerning the decrease of the SiO2 grade of the magnetite concentrate.

Sep 1, 2012

The molybdenum ores currently utilized in China are mostly molybdenum sulfide ores whereas oxidized molybdenum ores, being finely disseminated and difficult to process, have not been exploited and utilized effectively. In this article the beneficiation process of a molybdenum ore occurred in an oxidized ore zone was investigated in order to provide a new way for the development and utilization of the oxidized molybdenum ores in China. The molybdenum mineral in the ore was mainly wulfenite and the associated minerals included barite, limonite, quartz and small amount of cerusite. Limonite in the ore occurred in a crust and honeycomb-like colloidal state and composed the framework for the formation of the other minerals in the ore, which filled the pores in the framework. Wulfenite was mainly fine-grained and occurred in the fine porous crust and honeycomb-like framework. The finely disseminated ore structure made the separation and recovery of the molybdenum mineral in the ore very difficult. On the basis of the mineralogical study of the ore, experiments were conducted to compare the various mineral processing methods for the beneficiation of the ore, including single gravity concentration, single magnetic separation, single flotation, and a combination of high intensity magnetic separation and gravity concentration. The results indicated that with single gravity concentration a molybdenum concentrate containing 5.85 % Mo with a yield of 11.76 % and a Mo recovery of 43.5 % was produced. With single high intensity magnetic separation it was very hard to obtain a molybdenum concentrate product. With single flotation process a molybdenum concentrate containing 7.06 % Mo with a yield of 15.14 % and a Mo recovery of 62.63 % was produced. With a combination of high intensity magnetic separation and gravity concentration a molybdenum concentrate containing 6.46 % Mo with a yield of 11.81 % and a Mo recovery of 42.11 % was produced. In conclusion, compared to the other methods the flotation process can produce more reasonable technological and economical results and is the best process for the exploitation and utilization of the finely disseminated oxidized molybdenum ore.

Jan 1, 2014

By C. Y. Sun

In this paper, the development of research and practice on the separation process of fine complex Cu-S ore at a Copper Mine in south of China, was discussed. Since early 1980s, various processes were used, such as the process of bulk flotation-separation, the process of selection flotation and the process of iso-flotation. Especially when the process of selective flotation was put into operation, further development was achieved in beneficiation results, but the difficulty in separation of chalcopyrite from pyrite has not been solved yet, so causing a poor quality of Cu concentrate. The author has successfully developed a new separation process characterized by the use of collector thionocarbamate and fast flotation. The selectivity of fine chalcopyrite and pyrite was greatly improved. This process supplied a new route for the treatment of fine complex Copper sulphide ores.

Jan 1, 2014

By P. S. Rao

In 1951, Tata Steel became the pioneer in Asia by setting up its first ever washery in West Bokaro Colliery. The first beneficiation plant used to produce clean coal of 19% ash with chance cone. Feed size of chance washers were -75 mm to +6 mm. The fine coal (-6 mm) were used directly. With change in technology,in 1986,chance cones were replaced by DM cyclones and coal was washed in two circuits. In the coarse circuit -13 mm to +0.5 mm coal was washed in two stages while the fine coal of -0.5 mm was treated in froth floatation cell. With further improvement in the process the higher ash raw coal was feed to produce clean coal of 13% ash. In 1998, DSM cyclones were replaced by scrolled Evolute design cyclone which has Ep of 0.020 to 0.025 ranges resulting in increase efficiency of separation. With the increase in demand of clean coal, lower seam proportion has increased in raw coal production. The washability studies of individual seams indicated large difference in the seam characteristics in terms of washability and specific gravity cut points of the individual seams. So washing all seams together had resulted in frequent change in the character of coal and warrants frequent changes in the operating parameters of the plant in which the separating efficiency comes down and ultimately resulted in yield loss initially. With increase in knowledge and experience in coal washing the solution to this problem was achieved by adopting, seam-wise washing which is enabling process engineers by keeping set point for longer periods there by to enhance the separation efficiency. Keywords: coal processing, froth floatation, steam washing

Sep 1, 2012