Search Documents

By Jonguk Kim

The North Fiji Basin (NFB) is a mature intraoceanic back arc basin with an age of ~12 Ma. Recent volcanism and spreading activity are focused along the Central Spreading Ridge (CSR), A ridge segment more than 800 km long, composed of four main segments, the N160°, N15°, north-south (N-S), and southernmost segments from north to south. The dominant volcanic rock in the entire central spreading ridge is normal mid-ocean ridge basalt (N-MORB), very similar to those emplaced along mid-oceanic ridges. Conversely, influence of an oceanic island basalt (OIB) source increases northward from 18°20'S. Several basalts which show a significant subduction-related component are also observed in the southern part of the NFB. Hydrothermal activity along the spreading centers of the North Fiji Basin was investigated by several previous works, especially by the STARMER project in 1989 and 1991. Both extinct and active hydrothermal vents are found on the N15° and N-S segments. In contrast, only traces of hydrothermal activity have been found on the N160° segment. Although high temperature activity and related massive sulfide deposit on the N15° segment was further investigated by several follow-up studies, no systematic survey for other hydrothermal sites was conducted after their discovery. In 2012 and 2013, KIOST performed two hydrothermal expeditions aboard the R/V Onnuri in the three targeted areas of hydrothermal activity along the CSR of North Fiji Basin. All targeted areas include sites for hydrothermal activity reported in previous works. Occurrence and distribution of hydrothermal plume were investigated by combined

Sep 14, 2011

By Freddy Pøhner

The paper describes recent advances in the technology for mapping of the seabed with acoustic instrumentation. These instruments are typically single beam echo sounders, multibeam echo sounders and high resolution sub bottom profiler. For the single beam echo sounders, new features for deep water mapping are described, as well as the possibility for combining investigation of shallow areas with side scan sonar and vertical echo sounding in the same instrument. Multibeam echo sounding technology for deep and shallow water is reviewed, and some new high resolution instruments using dynamic beam focusing is presented. The sediment profiling technology deals with a novel design for high resolution sub bottom profiling, based upon a Mills Cross transducer with resolution as good as 3 degree in its largest configuration and a frequency range of 2,5 ? 7 kHz. Remarkable features of the system are a very high ping rate even for deep water, and the capability to map buried objects or structures by several simultaneous beams. Some results obtained with the first installation on the French research vessel ?Beatemps Beaupré? are presented.

Jan 1, 2003

By J. W. Jamieson

"The future of the marine mining industry is tied to the resource potential of the seafloor. Everything from economic feasibility, policy decisions and environmental impact assessments to extraction techniques and mining tool design rely on an understanding of the size, composition, and distribution of the deposits. Development and regulatory decisions must ultimately be tied to not only the grade and tonnage estimates of individual deposits or groups of deposits, but also an understanding of the uncertainty of these estimates. Here, we will discuss how seafloor massive sulfide (SMS) deposit grades and tonnages are evaluated, and the sources of the uncertainties associated with these values.TONNAGE UNCERTAINTYFirst-order tonnage (size) estimates for SMS deposits are primarily determined from calculating the volumes of material that occurs as positive bathymetric features on the seafloor. The extent of sulfide mineralization on the seafloor can be determined either from visual surveys (camera-tow, remotely-operated vehicle (ROV), or human-occupied submersible surveys) or from volume calculations of bathymetric features identified from digital elevation models of the seafloor, or a combination of both methods. For bathymetric models to be used to identify deposits in the absence of visual groundtruthing, data resolution of 1 m or less is generally required to confidently identify a feature as being hydrothermal in origin (as opposed to a volcanic or tectonic feature), and therefore near-bottom multibeam data acquisition (e.g., using autonomous underwater vehicle (AUVs) or remotely operated vehicles (ROVs) is required (Fig. 1). Specific characteristics of bathymetric features, such as shape, slope angles and surface roughness can be used to identify features of hydrothermal origin (Fig. 1). However, so far, bathymetric features mapped at a resolution of ~1 m cannot be relied upon to unambiguously distinguish a sulfide mound, and the additional use of multiple AUVmounted sensors, such as magnetometers, which can be used to detect hydrothermal upflow zones, or self-potential sensors, which detect electrical fields related to the oxidation of sulfide minerals, can increase the confidence that a bathymetric feature is indeed a sulfide body, without the need for expensive and time-consuming visual surveys (c.f. Petersen et al., this volume)."

Jan 1, 2017

By Alexander Malahoff

With its new continental shelf beyond the exclusive economic zone, New Zealand is a country with just 4% of its territory above water. The other 96% is submerged. New Zealand's marine territory covers an area about three-quarters the size of Australia. This territory includes large portions of the Gondwana continent from which NZ separated more than 80 million years ago. This underwater land mass extends from the shores of New Zealand to a water depth of more than 5,000 m, is largely unexplored and is almost certainly the site of many large, untapped oil, gas and mineral deposits. Underwater oil and gas drilling is now a universal activity. Underwater mining is in its infancy and will become a major activity in the future, contributing greatly to the New Zealand economy. New hydrocarbon deposits will undoubtedly be discovered under the ocean floor in regions such as the Great South Basin located off Canterbury and Otago. Mineral deposits are also undoubtedly located within the oceanic crust of this underwater NZ continent. These are as yet unknown and unexplored. The oceanic crust north of the North Island is currently being extended through the subduction of the Pacific plate into the Tonga Kermadec trench and through the growth of a line of submarine volcanoes extending north to Tonga. Active submarine volcanism has led to the growth of ocean floor mineral deposits consisting of polymetallic sulphides with iron, copper, zinc and lesser gold, silver and other metals.

Jan 1, 2011

By Sup Hong

"Lifting riser in deep-seabed mining (DSM) is exposed to acute and chronic stresses of materials, whose yield will result in the most critical loss of total mining system. For freehanging riser (FHR), the axial vibration and local bending of riser may produce acute stresses, in the meanwhile, vortex-induced vibration (VIV) in relative current, friction and collisions of solid particles with inner-wall, and material corrosion in seawater are representative causes of chronic stresses. The chronical stresses bring about fatigue failure or abrupt failure by material loss. Hydraulic lifting is effective and promising for transportation of minerals, however, ecofriendly treatment of operating seawater is an unease hurdle to come over. Sizing of riser section confronts multi-directional problems, i.e. safety of slurry transportation (flow assurance), material safety of riser (wall thickness), seawater treatment on board, etc.A free-standing riser (FSR) might exclude a part of design problems of free-hanging riser and give a way to sustainable mining. FSR stands vertically by means of sub-buoyancy part(s). The top of FSR emerges above sea surface and is connected with mining platform through jumper line (supported by external yoke). Total amount of sub-buoyancy and location(s) have to be carefully determined in viewpoints of dynamics of FSI (fluidstructure interaction) in waves and currents. The concept of FSR gives more freedom for design of multi-functional riser system in view of sustainability of DSM. In DSM, sustainability concept may be focused on eco-friendly treatment of seawater and sediment, and safety of total mining system. For feasibility of FSR, however, installation, maintenance and repair need to be investigated thoroughly in collaboration with industry experts"

Jan 1, 2017

By Felix Lehnen, Peter Kukla, Mirjam Rahn

"Significant uncertainty is associated with predicting future trends in deep-sea mining projects, especially when attempting to assess markets for associated products such as ships and collectors. In order to help European Original Equipment Manufacturers (OEMs) to appraise the future market share of deep-sea mining equipment, a methodology was developed that allows to assess and predict equipment turnover. This study presents a market analysis, which evaluates the scale of the potential market for deep-sea mining equipment for seafloor manganese nodules (SMnN) and seafloor massive sulfides (SMS) based on six key drivers: (i) the worldwide deposit potential of SMnN and SMS deposits, (ii) the profitability of deep-sea mining projects, (iii) the metal market of seven associated metals (Cu, Zn, Au, Ag, Co, Ni, Mn), (iv) the current legal and environmental situation in the Area, (v) investment and maintenance costs, and (vi) a competitor analysis.Figures for the different key drivers are based on public reports and expert interviews. Large uncertainties as well as contrasting views and expectations resulted in different options (scenarios) for the future development of the deep-sea mining market. Several scenarios were developed and based on the future number of “mining projects” in the short-term (2022-2041) and the long-term (2042-2061). The number of such mining projects has been calculated based on the combined analysis of the different key drivers.In the scope of this study, the definition of a “mining project” is a deep-sea mining operation for SMnN or SMS lasting for 20 years. This operation includes the purchase of a set of deep-sea mining equipment consisting of a mining support vessel, a vertical transport system and the seafloor mining equipment, in line with other work within the EU FP7 project “Blue Mining” (GA No. 604500)."

Jan 1, 2017

By P. C. Hollick

Two marine diamond deposits on concession 2b off Namaqualand along the South African Coast, have been systematically mined over the past year by the mv Moonstar. The two deposits, Smith?s Ulcer and Wedge Point Basin, are comparable in morphology, straddled the same water depths and have similar geology yet have given very different recoveries when compared to their respective grade models. These differences are best ascribed to the different style of mineralisation observed within the two deposits which has been directly controlled by the bedrock morphology. The smith?s Ulcer deposit has been formed in a metagreywacke bedrock displaying a strong north-south trending foliation which dips steeply to the west. Consequently the mineralisation is confined to narrow north-south linear trends with limited lateral extent (less than 5m) making extraction extremely difficult and somewhat variable. RE factors (recovered grade versus estimated grade) for this deposit range from 0.5 to 1.1. The Wedge Point Basin deposit is formed in a micaceous metaquartzite with a conjugate southwest northwest joint set, the southwest lineation being the more prominent, and structural foliation dipping gently to the west. The resultant style of mineralisation is confined to basinal features defined by topographical lows and is fairly lateral in extent (in order of 50m). Extraction of the mineralisation from this deposit is less arduous with recoveries more uniform, RE factors are frequently in the range 2 - 3. This style of mineralisation is more in line with what is to be expected from marine alluvial deposits, the nugget effect of diamond concentration being responsible for the high RE factor. The long narrow linear trends observed in Smith?s Ulcer demonstrably require a specialised approach in successfully sampling, modeling and ultimately mining.

Jan 1, 1998

By Janine Lahr, Peter E. Halbach

The Manus Spreading Ridge is located within the EEZ of Papua New Guinea and lies in the Manus Basin ENE of the PNG Island and N of the Island New Britain. The divergent backarc spreading system is caused by the subduction of the Solomon plate in the South under the Bismarck plate in the North along the lineament of the New Britain trench. The rate of divergence is relatively high compared to other back arc spreading systems and amounts up to 12 cm/year [3]. Since submarine volcanism and associated hydrothermal circulation as important parts of the oceanic heat transfer system are also dependent on the rate of spreading, hydrothermal fluid venting and respective deposition of polymetallic sulfides can be expected there. In late 1985 first indications for hydrothermal activity were observed on a swell within the central rift valley of the Manus Spreading Centre during a photographic survey of the seafloor by an expedition of the Hawaii Institute of Geophysics with the American RV Moana Wave [1]. Detailed geological investigations including successful sampling were first carried out in June 1990 within the scope of the OLGA II research project (conducted by Prof. Tufar, Marburg) using the German RV Sonne equipped with a deep-sea television sledge and Tvcontrolled grab systems. Simultaneously a research cruise with the Russian RV Akademic Mstivlav Keldysh took place using the manned submersible Mir; the findings of the OLGA II cruise were immediately used for planning and organization of the Mir dives [3]. The massive sulphide samples which we used for our geochemical and mineralogical studies originate from the hydrothermal fields 1 and 2 and are from grab stations of the OLGA II expedition [4].

Sep 24, 2006

By Lorena Blanco, Guillermo Gómez-Ramos, Iker Blasco, Egidio Marino, Luis Somoza, Ricardo León, Teresa Medialdea, Javier González

"This study presents the first catalogue of marine mineral deposits and energy resources along the continental margin of Spain. Aggregates, oil and gas and metalliferous mineral areas have been defined and mapped. The catalogue, implemented in a geographic information system (GIS), is conceived as a first national database within the European network, which is being built as part of the EMODnet-Geology project. It comprises 8 types of mineral and energy resources for the Spanish margins: aggregates, hydrocarbons, evaporites, placer deposits, phosphorites, polymetallic sulfides, polymetallic nodules and cobalt-rich ferromanganese crusts (Figures 1 and 2). The catalogue stores a total of 409 marine mineral deposits and compiles information such as name, deposit type, main morphology, main minerals, setting or area extent for each mineral deposit. By number of deposits compiled, the aggregates are the most abundant (286) followed by hydrocarbons (62), cobalt-rich ferromanganese crusts (32), evaporites (9), placer deposits (8), phosphorites (5), polymetallic nodules (4) and polymetallic sulphide deposits (3). Considering the total extension, hydrocarbons (32,386 km2) and cobalt-rich ferromanganese crusts (24,951 km2) represent the biggest areas.The Geological Survey of Spain (IGME) is developing a new tool in the catalogue, according the International Seabed Authority (ISA) Database parameters, for individual samples on each ferromanganese deposit. The database includes an extensive collection of records that comprise five information groups: general cruise and sample data, physical properties, mineralogy, geochemistry and acronyms used. New attributes have been incorporated, in example: geophysical, sedimentological and petrological data in the deposit area, sample weight, porosity, morphology, textural and structural features, geochemistry of major, minor and trace elements (included REEs and PGEs) and supplementary cruise and laboratory reports. This new database complements the EMODnet-Geology project minerals catalogue, offering a deeper level of information for the areas with major potential for mineral or energy resources as they are the Canary Island Seamount Province, the West Margin of Galicia and the Gulf of Cadiz."

Jan 1, 2017

By Robert Heydon

With the United Nations Conference on Sustainable Development fast approaching it is timely to reflect on the integral role seafloor polymetallic nodule mining will play in facilitating sustainable development and alleviating global poverty. Polymetallic nodule mining presents mankind with a unique opportunity to advance the world?s sustainable development aspirations, particularly given the ultimate beneficiaries from polymetallic nodule mining will be the billions of people around the world that require greater access to more affordable minerals for their social and economic development. This paper discusses the importance of polymetallic nodule mining in the context of sustainable development and forecasted growth trends, supply and demand dynamics, the decreasing grade and quality of terrestrial mineral resources, and the Green Economy, as well as in light of a comparative analysis that demonstrates polymetallic nodule mining offers a socially and environmentally advantageous alternative to terrestrial mining.

Jan 1, 2011

The Brothers hydrothermal system is host to two very contrasting vent fields and to date, is the only known example of this kind for any submarine arc volcano in the world. Firstly, there is the NW caldera field. It is perched on the caldera walls and is up to 1,200 years old, and represents a more ?mature? system dominated by water/rock interactions, though there is also evidence for magmatic contributions to the hydrothermal fluids. It is host to relatively high temperature (~300°C), focused venting of metal-rich fluids. Large Cu- and Zn-rich sulfide chimneys occur at this site, with high concentrations (up to 90 ppm) Au apparent in some chimneys. Vent fluids of the NW caldera site show sub-seafloor phase separation is occurring at this site. Silica concentrations in these vent fluids are consistent with the vent fluid temperatures. Secondly, there is the cone vent field that is much younger, and which sits atop the summits of a main cone (the Upper cone) and an adjacent satellite cone (the Lower cone) that occur inside the caldera, near the southern caldera walls. This field is dominated by S-rich vents with vent fluids more diffuse, lower in temperature (<120°C), very gassy and acidic (to pH 1.9), and relatively metal-poor. Fluids of the cone site have Mg and SO4 concentrations higher than seawater values, indicating these ions have been added to the hydrothermal fluid and are not being depleted via normal water/rock interactions. Variability occurs between the two cone vent fields, with the diffuse discharge observed at the Upper cone volumetrically small and chemically different from the Lower cone. For example, from the vent fluid Mn, Li, Rb, and Cs concentrations, it is apparent that the Lower cone has experienced a lower degree of water/rock interaction (i.e., more reaction) than the Upper cone. Vent fluid pH is higher for Lower cone, consistent with more reaction and neutralization of acidic gases. Fe/Mn is lower at the Lower cone due to decreased Fe solubility at the higher pH. The lowest pH sample (1.9) is from the Upper cone that has 39.4 mmol/kg of SO4, consistent with input of magmatic SO2 and disproportionation to sulfuric acid and S or H2S. Thus, the Upper cone site could be interpreted to have a shorter reaction path and residence time between the point of magmatic degassing and the seafloor venting than the Lower cone site. Isotopic compositions of the NW caldera and cone vent fluids show evidence for magmatic water with negative dD and d180 values, while 3He/4He values show the Brothers hydrothermal system has shifted towards more magmatic conditions over the past several years with both sites affected by magmatic events. Similarly, vent fluid sulfide d34S values and those for sulfide minerals from NE caldera chimneys also indicate disproportionation reactions involving magmatic SO2. Minerals such as chalcopyrite, bornite, chalcocite, covelllite and euhedral grains of hematite occurring in high temperature chimneys from the NW caldera site are consistent with a more oxidizing, magmatic fluid, while bulk sulfide geochemistry data show evidence for a higher temperature suite of elements (e,g., Mo, Co, Se) associated with Cu-rich chimneys. Gold mineralization occurs in these high temperature chimneys and is associated with the most recent deposition of high concentrations of Cu, where d34S values are most negative. Geophysical evidence suggests that the top of a magma chamber occurs ~2.5 km below the caldera floor, beneath the cone site in the SSE quadrant of the volcano. Very low velocities of <1 km-2 are seen in the seismic data between the magma and the seafloor, and are indicative of gas release. Harmonic tremor data provide evidence for a 500 m pipe-like ?conduit? located above the magma chamber (and below the cone), linking it with the overlying hydrothermal system, providing a mechanism for magma-derived metals to enter the hydrothermal system under the cone site. The NW caldera and cone sites are considered to represent stages along a continuum between magmatic-hydrothermal and water/rock-dominated end-members.

Jan 1, 2010

By Laurie Meyer

The need for improved, high confidence estimates of nodule abundance to support mine permitting, detailed mine planning and mining and processing equipment design is evident. To date, physical samples represent the ?Gold Standard? for nodule abundance measurement, and are likely to remain as such. However, there are some interesting improvements in the area of 3-D scanning which, if marinized for operations at 6000m, may prove to be reliable alternative methods for mapping abundance over large areas particularly if calibrated or benchmarked with physical sample data. . Features of a high confidence physical sampling device, such as the 0.75m2 (0.86m on a side) box corer developed and successfully used by the Kennecott Group for exploration in the CCZ, take into account not only the accuracy in nodule sample collection but a host of other operability considerations which can mean the difference between a successful exploration cruise yielding high numbers of large area samples and one in which few, inaccurate, often inconclusive samples are collected (or, even worse, the sampler fails to grab any nodules for any number of reasons). The collection of physical samples at appropriate spacing within a mine area combined with more qualitative indications of nodule density such as can be obtained using acoustic backscatter should prove adequate for the near term objectives related to overall abundance appraisal or estimates of ?indicated? resource. Looking ahead, exploration cruises will need to yield increasing amounts of data to support development of higher confidence resource abundance estimates to support issuance of mining permits and detailed design of mining plans and equipment. It is likely

Sep 14, 2011

By William D. Siapno

Mining the deep ocean by the year 2000 may seem far fetched. The year 2000 is but a decade away, a scant 10 years. Remember, the youngsters of today will grow up in a little more than a decade and rebut the wisdom of the ages, especially the traditions of their elders. Rude perhaps, but none the less a fact of life. Ocean mining exhibits many of these same traits. We should all brace ourselves for some rude shifts in our rapidly moving society. Major shifts in economics, politics, and social orders are the rule of the day. Communism is in retreat, our own economic structures chaotic. So in this moment of cataclysmic change, a shift in the international market place of mineral resources should not be a great surprise.

Jan 1, 2011

By Ian B. Corbett

De Beers Marine Pty Ltd. (South Africa) (DEBMARINE), a wholly owned subsidiary of De Beers Consolidated Mines Ltd. specializes in the provision of contracting and consulting services for offshore diamond exploration, Mineral Resource Management and mining. Established in 1983, the company is strongly focused on driving and sustaining growth of the offshore diamond mining industry into the 21st century. DEBMARINE provides full Mineral Resource Management and produce almost half a million carats annually for the Namibian Diamond Corporation (Pty) Ltd. from their offshore mining licence. The company is also extensively involved in feasibility studies to establish new mining ventures and in the exploration of several offshore Prospecting Licence Areas for other clients. As a pioneer in this field, DEBMARINE remains highly focused on technological development. A specialized section, the Technical Development Business Unit, has been established. Through relationships with various technology leaders, this unit develops new sub-sea mining technology and delivers productivity innovations aimed at realizing maximized carat extraction. This talk provides a broad perspective on the development of the Namibian offshore deposits and examines the critical role played by high-resolution orebody characterization and high-confidence Mineral Resource development at De Beers Marine.

Jan 1, 1998

By J. R. Woolsey

In late 1988, the Committee for Coordination of Joint Prospecting for Mineral Resources in South Pacific Offshore Areas (CCOP/SOPAC), Suva, Fiji, consulted the Continental Shelf Division of the Marine Minerals Technology Center regarding low-tech, low-cost, reconnaissance sampling systems for a variety of nearshore needs. Materials of interest to several member island nations included silica and calcareous aggregate for cement manufacture, sand for beach replenishment, heavy minerals, and precious metals. A principal criteria of the system was that it be of low-tech design, and as far as possible, suitable for construction on the islands from available materials. It should also be operable with SOPAC personnel on island vessels of opportunity. The system selected to satisfy these requirements was a convertible drill of basic airlift design, capable of operating with easy modification as either a vibralift or airlift, depending on the desired application. The basic system included a drill pipe constructed of heavy duty 76 mm (3") black iron pipe, divided into three 3 meter sections (for ease of transport), fitted with an air intake manifold and bit at the lower end. A 25 mm (1") galvanized pipe assembled in three similar sections and clamped to the drill pipe served as a water jet to assist in cutting. Air was supplied to the manifold by means of a 12 mm (1/2") pipe also clamped along the length of the drill pipe. Suitable hoses supplied water and air to the upper ends of the respective pipes by means

Jan 1, 1989

By Michael J. Cruickshank

The State of Hawaii has expressed concern over deterioration of the tourist beaches at Waikiki, which are becoming seriously depleted of sand. In this report the options for acquisition, transportation and placement .of sand on the beach are examined with respect to feasibility and cost. Ten sources of sand were compared, including commercial, from Australia, Maui, and Barbers Point (3), deposits offshore of the Reef Runway (3), offshore of Waikiki (3), and offshore of Molokai from the Penguin Bank (1).

Jan 1, 1991

By Natalia Konstantinova, Kira Mizell, James R. Hein, Georgy Cherkashov, Amy Gartman, Mariah Mikesell

"Two types of metallic deposits have been found in the deep Arctic Ocean: Hydrothermal Fe, Cu, and Zn sulfide deposits form along Gakkel Ridge in the Eurasia Basin and associated ridges between Greenland and Europe; and iron and manganese oxide crusts (Fe-Mn crusts) and nodules, precipitated from seawater onto rock surfaces in the Amerasia Basin, contain many rare metals of economic interest. Fe-Mn crusts and nodules collected in the Amerasia Basin during 2008, 2009, and 2012 cruises on the USCGC icebreaker Healy are characterized by unique mineral and chemical compositions, very high Fe/Mn ratios, fast growth rates, and other unique characteristics compared to those formed elsewhere in the global ocean. These characteristics reflect temporal and spatial variations in geological, oceanographic, and climatic conditions in the Arctic Ocean and surrounding continents over the past ~15 Myr.RESULTS AND CONCLUSIONSDiscrimination diagrams show that the crusts and nodules found in the Amerasia Basin north of Alaska are hydrogenetic. However, the mineralogy is not typical for hydrogenetic Fe-Mn crusts and nodules, which usually include only amorphous Fe oxyhydroxide and ?-MnO2 (vernadite). The Arctic samples also include the Mn oxides birnessite and 10Å manganates (todorokite, buserite, asbolane), and the Fe minerals also include goethite, lepidocrocite, feroxyhyte, and ferrihydrite. This mineralogy reflects formation under lower oxygen conditions than typical for samples formed elsewhere.The Amerasia Basin crusts have a unique chemical composition compared with crusts from other areas of the global ocean. The key difference is the high Fe contents relative to Mn contents, which determines the types of trace metals hosted by the Fe-Mn oxide phases, and their concentrations. The high Fe/Mn ratios reflect the expansive continental shelves (>50% of the Arctic Ocean) and upper slopes that support redox cycling and release of Fe and other metals to bottom waters, and to the large fluvial input from North America and Siberia. Brine formation on the shelves and currents promote the distribution of the metals throughout the Amerasia Basin, including the deep basins."

Jan 1, 2017

By Andrea Koschinsky

Numerous hydrothermal vents occur along the Earth?s oceanic spreading axes documenting the reaction of seawater with hot magmatic rocks. The circulation of seawater through the oceanic crust, the interaction with hot rocks in the crust, and the subsequent discharge of hot metal- and gas-rich fluids into the ocean have significant implications for the cycling of material and energy on Earth. Until recently, hydrothermal activity was unknown from the Mid-Atlantic Ridge (MAR) south of the Equator where the MAR is offset by about 1000 km at the St. Paul?s and Romanche fracture zones. During a British cruise in February/March 2005, the first active hydrothermal vent field was discovered on the southern MAR at 5°S. During our follow-up cruise M64/1 in April 2005, the first samples from this vent field were recovered with the ROV QUEST (Univ. Bremen) and analyzed onboard. The high-temperature vent field is situated in a water depth of 2990 m along a line of collapse pits within a large basaltic sheet flow. A diffuse, low-temperature field occurs in a jumbled sheet flow few hundred meters to the east with warm water streaming out of cavities between lava blocks. Here we show for the first time that boiling fluids of ~400°C are emanating from sulfide-bearing vents at a depth of about 3000 m at a slow-spreading Mid-Atlantic Ridge segment. Although this segment is composed of thick basaltic crust, these fluids are dominated by hydrogen relative to methane. Whereas the active chimneys consist of pyrrhotite, chalcopyrite, and isocubanite, the mineral association hematite-magnetite-pyrite occurs in the inactive chimneys suggesting that the fluids became more reducing in present times. The high hydrogen contents and the high temperature of the fluids as well as the change to more reducing conditions are most likely related to a young volcanic eruption event some 300 m east of the hydrothermal field. The presence of hematite and magnetite may indicate that the upflow zone or even the reaction zone at 5°S used to be more oxidized then at other MOR sites, where the hydrothermal fluids are commonly buffered by the pyrite-pyrrhotite-magnetite (PPM) buffer. Consequently, high iron contents and high hydrogen/methane ratios occur in high temperature fluids from basaltic host rocks rather than being restricted to ultramafic host rocks. Faunal communities at the South Atlantic vents largely resemble those from the North Atlantic vents implying that the large Equatorial fracture zones do not inhibit or obstruct faunal exchange along the Mid-Atlantic Ridge.

Jan 1, 2005

By Jonguk Kim

Hydrothermal sulfides were recovered from the16°50?S triple junction area in the North Fiji Basin, at a water depth of ca. 1900 m. The chimney samples can be divided into three groups according to their major metal contents: 1) type 1 (Fe-Cu-rich), 2) type 2 (Fe-Cu-rich with minor Zn), and 3) type 3 (Zn-rich) chimneys. Type 1 chimneys are mainly composed of chalcopyrite and pyrite, and are enriched in elements commonly precipitated under high temperature conditions (> 300°C), such as Cu, Co, Mo, and Se. Type 3 chimneys consist dominantly of sphalerite and marcasite with traces of pyrite and chalcopyrite, and are enriched in elements commonly associated with low temperature (150 to 250°C), such as Zn, Cd, Pb, As, and Ga. Type 2 chimneys show mineralogy similar to that of type 1 chimneys but their metal contents range between type 1 and type 3 samples. Trace element compositions of basaltic rocks indicate that magma generation in the triple junction area was influenced by two different sources: N-MORB and E-MORB. Sulfur and lead isotope patterns of the hydrothermal chimneys show distinct differences between the type 1 and type 3 chimneys. For example, type 1 sulfides are depleted in 34S and have lower Pb isotope ratios compared to type 2 and 3 chimneys. The d34S values (0.4 to 5.6?) of chimney sulfides are typical range of sulfur isotope composition of sediment free mid-ocean ridge hydrothermal system. Type 2 and 3 sulfides show slightly higher d34S values than type 1 sulfides, which can be explained by subsurface boiling of hydrothermal fluids followed by mixing of saline solutions with ambient seawater. Lead isotope compositions of the chimneys indicate that the Pb in type 1 and type 3 chimneys originates from hydrothermal leaching of N-MORB and E-MORB volcanic rocks, respectively. Considering that both these chimneys are located in the same area, our model suggests that type 1 chimneys formed by hydrothermal circulation controlled by an intrusion of N-MORB magma; the fluids were not influenced by boiling during the formation of type 1 chimneys. In contrast, type 3 chimneys are younger and were formed by hydrothermal circulation closely related to E-MORB magma intrusion at shallower depth. The necessary conditions for phase separation of the hydrothermal fluids that formed the type 3 chimneys might result from changed P-T conditions in a shallower high-temperature reaction zone beneath the hydrothermal venting site. Under these conditions the fluid may cross the two-phase boundary for seawater, ensuring subcritical phase separation. The mineralogical and geochemical properties of these chimneys suggest that type 1 and type 3 chimneys were probably black smoker and white smoker, respectively. Type 2 chimneys might be product of low-temperature replacement of type 1 chimneys, which is related to formation of type 3 chimneys.

Jan 1, 2005

By W. D. Siapno

Marine mineral resources have been reviewed in great detail on numerous occasions over the past few years. A summary of these efforts would indicate there is little new on the horizon as far as economic programs are concerned. Deep ocean minerals, though not forgotten, hold little promise for development in the immediate future, i. e., manganese nodules, cobalt crusts, polymetallic sulfides, etc. Nearer to shore, within the EEZ, and particularly within waters under state control greater industrial interest is expressed. Interest in sand and gravel not only persists but is growing, dependent largely upon the construction industry. Precious metals demonstrate the greatest growth potential.

Jan 1, 1988