Search Documents

By W. J. Stickney

"Over-all recovery of cadmium has been increased at the plants of the Hudson Bay Mining and Smelting Co., Limited, since the construction of a slag fuming plant and baghouse where smelter flue dust is recovered. This pa-per outlines the distribution of the cadmium in plant products from the concentrator to the refining department.The leaching of cadmium-bearing precipitates from the zinc plant is also discussed. This consists of a two-stage leach; first with sulphuric acid and then with copper sulphate. Details of the leaches are outlined along with the safety measures practised in handling the hydrogen and arsine evolved.The paper describes the final preparation of electrolyte for the refining cells by purification for copper and thallium. Deposition of cadmium, using a polyacrylamide as an addition agent, is discussed.An outline is given of the melting procedures, under either sodium hydroxide or zinc chloride, and of the sub-sequent treatment of the dross to recover entrained cadmium and thallium."

Jan 1, 1966

By M. Fainerman-Melnikova

The use of strong base ion exchange resins for the extraction of uranium was pioneered in the 1950?s. Ion exchange technology is applicable to dilute leach solutions such as those obtained from in-situ, heap leaching or in-plant processing of low grade ores. A further advantage of ion exchange processes is that fluidised bed technology allows for treatment of solutions with a relatively high concentration of suspended solids and resin-in-pulp technology can treat leach slurries. However, the extraction of uranium with strong base resins is severely affected by the presence of chloride ions in solution. In areas where high quality water is not readily available, the use of saline water as process water would extend the potential application for ion exchange in uranium processing. Our research program has studied the effectiveness of a wide range of commercially available ion exchangers in uranium extraction from saline solutions. In the present work, we examine the impact of salinity (ranging from chloride concentrations found in groundwater to those present in sea water), on the uranium extraction with weak base anionic resins (WBA). The effect of pH and the presence of the competing impurities are also discussed.

Aug 1, 2010

By P. M. Chapman

Risks to aquatic receiving environments from uranium mining and milling fall into three categories: physical (habitat change), chemical (e.g., uranium, selenium, total dissolved solids [TDS], metals including vanadium), and radiological. Although all categories of risk need to be managed, chemical risks are the most significant and are typically chronic rather than acute. For instance, selenium toxicity is primarily manifested as reproductive impairment due to maternal transfer, resulting in embryotoxicity and teratogenicity in egg-laying vertebrates. Risk is best assessed using a weight of evidence approach focused on ecosystem services. Risk management should be based on both risk assessment and adaptive monitoring.

Aug 1, 2010

"The Society for Mining, Metallurgy, and Exploration (SME) Inc. developed a guide of minimum standards for reporting exploration results, mineral resources, and mineral reserves for the purpose of informing the general public. The SME Guide has been adopted by the Society.History1. In 1988, at the request of members of the Society for Mining, Metallurgy, and Exploration (SME), Inc., the President of SME formed Working Party #79, Ore Reserve Definition, with the mission to develop guidelines for the public reporting of exploration results, resources, and reserves. A Subcommittee was appointed by the Working Party to draft these guidelines and submit recommendations to SME. The Subcommittee's recommendations were published by SME in the April 1991 issue of ""Mining Engineering"", and as a document entitled ""A Guide for Reporting Exploration Information, Resources, and Reserves"" (the SME Guide) in January 1992. Work continued on an ad-hoc basis until 1996, when Working Party #79 was renamed the SME Resources and Reserves Committee and became a standing committee.In 1994, the Council of Mining and Metallurgical Institutions (CMMI) started a concerted international effort to create a set of international definitions for reporting mineral resources and mineral reserves. An ad-hoc International Definitions Group was formed, with representatives from mining and metallurgical institutions from the United States (SME), Australia (AusIMM), Canada (CIM), the United Kingdom (IMM) and South Africa (SAIMM). A major breakthrough came on October 18, 1997 when the CMMI International Definitions Group met in Denver, Colorado and reached a provisional agreement (the Denver Accord) on definitions of mineral resources and mineral reserves. Concurrently, and since 1992, the United Nations Economic Commission for Europe (UN-ECE) was developing an international framework classification for mineral resources and mineral reserves. Starting in October 1998, joint meetings were held in Geneva between the CMMI International Definitions Group and the UN-ECE Task Force, resulting in agreement to incorporate the CMMI definitions into the UN framework classification."

Jan 1, 2003

By Stephen Williams

This paper examines manning best practice in the Australian mining industry. In particular, the paper considers a range of mining operations and their manning levels as measured by operational benchmarking. The benchmarking results presented cover 15 open pit and 37 underground studies in Australia. The data was collected as part of AMC?s benchmarking and operational improvement studies conducted between 1999 and 2008. The results examine overall manning levels in mining, processing and administration functions. Manning levels for a range of mining methods, including open pit and underground methods, are segmented. Productivity measures such as ore tonnes per man day and metres developed per man day are presented and where direct relationships can be established, the relationships are described. Finally, the paper considers perspectives on best practice with regard to manning in the Australian mining industry and the limitations in application of this type of analysis in a global context.

May 1, 2009

The control of carbon concentration in a counter current carbon absorption circuit is critical to optimise gold recovery. MINTEK has developed a carbon movement controller to address this potentially problematic area in gold extraction. This controller reduces operator interaction by automating carbon movement. Elution schedules are entered into the control system, which then moves the carbon through the circuit into the first adsorption tank until enough carbon is available for elution. This is done while maintaining the specified carbon profile within the circuit. MINTEK has also developed an online-carbonconcentration- meter to measure carbon concentration in pulp. The meter uses an ultrasonic measurement technique. Long term testing has shown the measurement to be robust and require minimal maintenance. Results from a gold mine in South Africa’s well known Witwatersrand gold producing area has shown a decrease in soluble gold loss between 30 - 50% when the controller was used.

Jan 1, 2014

A series of small scale tests have been conducted to evaluate the effect of micro-fracture development, imposed by blasting, on the material properties of the rock as well as its resistance to crushing and grinding. The uniaxial compressive strength, tensile strength, Poisson?s ratio, P-wave, Swave velocity, point load test index, crushing and grinding work indices were evaluated for samples without any blasting load and for samples which had received a variety of blast loads ranging from a single impact with low strength detonating cord, to combination of impacts at different times and significant impacts with powder factors close to those used in practical blasts. It was shown that the rock mechanics parameters change even at low impacts, suggesting easier crushing of the rock. Damage values appear to be affected by timing as stress wave superposition affects the damage process. Fragmentation is achieved at higher impact levels while work index modification of the fragments is also observed when high powder factors are used, suggesting improvements in grinding.

May 1, 2003

By Nelson C. White

This paper summarizes the present state and future prospects of the potash industry, with special reference to its impact on production in Saskatchewan.

Jan 1, 1968

By Sobczyk

The article will present a comparison of classifications of resources according to the JORC Code System with Polish classification, basing on system used in Eastern Europe. The differences between these classifications are significant. The information about mineral resources in Poland is not comparable to the main international system of reporting reserves like JORC, SAMREC, and PERC. Although comparisons between these systems are used, the transfer of particular categories of resources from the Polish system into a JORC category is not simple. Basing on the examples of privatization of Polish coal companies through initial public offering on the Warsaw Stock Exchange, the current practices providing guidelines how to convert resources from the Polish classification to the JORC system are described. Such independent assessment of resources is necessary for development of Mineral Expert?s Report (MER or CPR) which is an integral attachment to the prospectus.

Aug 1, 2013

By Yosuke Ota, Makoto Tawara, Tetsuya Kojima

"Dry-lube has been used in Europe to enhance formability of aluminum sheet for automotive applications, but it is difficult to ensure degreasing performance with lower degreasing bath temperature. However, newly developed, highly lubricating pre-coats utilizing a urethane resin, which is soluble in water, have been found to show excellent degreasing performance. Furthermore, a richer pre-coat weight coincides with a lower friction coefficient and better formability. Combined use of anti-rust liquid oil showed different friction coefficient depending on applied surface pressure.INTRODUCTION The global demand for aluminum alloy products, especially for automotive application, has been increasing because aluminum alloys can offer excellent corrosion resistance with good strength and low density compared with steel. Aluminum alloys can contribute to saving much more energy and greenhouse gas emissions over the lifetime of the product. On the other hand, the amount of aluminum alloys in vehicle architectures is still somewhat limited due to relatively low formability. As a consequence of this low formability, it is necessary to set a certain limit to the shape of an aluminum alloy panel for automotive applications. So far hot melt wax dry lubricants have been in use especially in Europe as they have been recognized to provide better lubrication than conventional rust protection oils (Meiler & Jaschke, 2005). The benefit of hot-melt wax for automotive manufacturing is associated with a more stable forming process and the possibility to avoid extra lubrication in the press shop. But because of the low poorer solubility of hot-melt wax in degreasing aqueous bath solution, a higher degreasing temperature is required so that no remnant of hot melt wax can be carried over to the next manufacturing process. This temperature control is difficult to impress upon a manufacturing degreasing bath originally designed for liquid oil, especially in Japan. The typical temperature of degreasing bath in Europe is around 60°C, while it is only around 40°C. in Japan. Various types of pre-coats other than hot-melt with high lubricity have been reported (Tawara, 1993; Ueda, Hatsuno & Totani, 2013), but a balance between sufficient degreasing performance and high lubricity has not yet been achieved for an actual production process line."

Jan 1, 2018

By Helmut Lerchs

An open-pit mining operation can be viewed as a process by which the open surface of a mine is continuously deformed. The planning of a mining program involves the design of the final shape of this open surface. The approach developed in this paper is based on the following assumptions: 1. the type of material its mine value and its extraction cost is given for each point; 2. restrictions on the geometry of the pit are specified (surface boundaries and maximum allowable wall slopes); 3. The objective is to maximize total profit-total mine value of material extracted minus total extraction cost. Two numeric methods are proposed: A simple dynamic programming algorithm for the two-dimensional pit (or a single vertical section of a mine), and. a more elaborate graph algorithm for the general three-dimensional pit. ASURFACE mining program is a complex operation that may extend over many years, and Involve huge capital expenditures and risk. Before undertaking such an operation, it must be known what ore there is to be mined

Jan 1, 1965

By Nicolas Gatelier, Sophie Laurent, Thierry You

Hard-rock caverns for hydrocarbon storage are a very particular type of underground facility controlled not only by local administrative and regulatory constraints that can be very specific, but also by the possible risks of geotechnical or geomechanical failure. Each such facility throughout the world is a prototype that needs to be adapted to very different site conditions. The straight forward application of design methodologies from relatively similar fields (mines, tunnels) can be very useful, but risks holding back the scientific and technical improvements needed by an engineering industry in full development. Here we look at various case histories and at problems that have been raised where recent attempts at standardization would appear to have been ill adapted, and where storage designers, through experience and judgment, may still provide innovative engineering solutions.

Jan 1, 2015

By T. B. Williams

Most geologists have felt the need of a longer base than is ordinarily available when using a Brunton compass or other convenient instrument for taking strikes and dips in the field. To overcome this difficulty a lath or stick with straight parallel sides is frequently used. This accessory adds to the accuracy of the work, but it is a decidedly inconvenient one for the geologist to carry, especially if he be heavily loaded or is travelling on horse-back or through thick brush on foot. The writer has abandoned its use in favour of a sturdy two-foot carpenter's rule. The rule preferred is manufactured by J. Rabone and Sons, Birmingham, England. It is provided with a good level-bubble set in one of the limbs, and a scale, of the protractor type, graduated to five degrees through 180 degrees, attached to the main joint at the middle of the rule. (See Figure 1). For an instrument of its kind it is very accurate, and, in addition to the uses mentioned below, it 'is a handy thing to have around any camp. It is frequently used when plotting roughly in the field and for a protractor when one is not available. When not in use it may readily be carried in the top of the high-boot or legging. Ordinary strikes are measured as illustrated in Figure 1, the compass being held against the rule, which is in a horizontal position. Dips may be measured in a corresponding way by holding the Brunton compass against the extended rule, which is thus used merely as a straight edge. It is usually much more convenient, however, to ? use the rule only for this purpose, in which case one foot of the length rests as a straight-edge against the rock surface. This adaption is shown in Figure 2.

Jan 1, 1929

The steam-filtration process for dewatering solids involves the application of slightly superheated steam to a filter cake during filtration. The mechanism by which the technique promotes water removal has been deduced from bench-scale experiments on coal and on granular iron ore concentrates. The mechanism, along with some of the applications and limitations of the process, is presented. Introduction I N the steam-filtration process, slightly super-heated steam is applied to the filter cake during filtration to remove more water than can be extracted by conventional filtration. Although this process was developed by Burton for coal filtration (1), it should have far wider applicability; certainly, it could be used to treat any mineral product, because only low-temperature steam is needed and most conventional filtration equipment can be easily adapted to it. As few restrictions apply to this process, however, it is important that its more obvious advantages and disadvantages be appreciated and, especially, that the criteria on which economic evaluations can be based are understood.

Jan 1, 1965

By John E. Udd

"In this paper the author presents the results of the 1992 CIM survey of graduates in minerals and technology programs in Canadian post-secondary institutions. As usual, the trends are out-of phase with the economic state of the industry. People who chose a minerals career in the prosperous days of the late 1980sare now entering a labour market in recession.The cyclical nature of enrollments is illustrated in a series of figures showing the trends since the CIM survey Wa5 begun in 1956 (and even earlier for mining engineering).In the survey, the respondents were asked to provide comments on their perceptions of the problems specific to minerals education in Canada. The large number of responses have led the author to the conclusions and recommendations given in the final part of the paper."

Jan 1, 1993

By Mark Freberg

"IntroductionThis chapter is intended to provide information on the operation and maintenance of several pieces of equipment used in heavy media separation. Most heavy media separation circuits, particularly those involving bath separators can be considered as high maintenance areas. Because of this the efficient operation and maintenance of these circuits is very important if the cost per ton of material treated is to be kept to an acceptable level.Heavy media separation (HMS), is a process used to separate particles of different specific gravities. Under laboratory conditions the ideal way to separate two types of particles which have different specific gravities is to suspend them in a heavy liquid which has a specific gravity between those of the two types of particles. Those particles with the lower specific gravities will float on top of the liquid while the higher specific gravity material will sink to the bottom. Given enough time and a sufficient volume of heavy liquid this process will be essentially insensitive to the sizes of the particles involved.Heavy media separation circuits make use of the same principles described above. The material to be treated is introduced into a mixture of finely ground solids, called media, and water which takes the place of the heavy liquid; the mixture of solids and water is known as medium. The separating force can be either gravity or centrifugal force. The type of solids used as media varies but it is usually a high specific gravity material such as magnetite, galena or ferrosilicon.Heavy media separation is used extensively in the cleaning of coal and to a lesser extent as a preconcentration step in base metal and iron ore operations."

Jan 1, 1989

By Robert D. Irvine

"Enhanced concern for protection of the environment and attendant actions by environ-mental regulatory authorities in support of this concern are influencing, to varying degrees, the demand and supply of a range of industrial minerals in a number of jurisdictions. These influences take a variety of forms.In this paper, the author seeks to delineate certain broad trends which are occurring relative to industrial minerals and the environment and then, through a series of examples, to outline opportunities, developments, and impacts respecting a number of industrial minerals produced and consumed in Canada and the United States."

Jan 1, 1996

By Alessandro Navarra

Discrete event simulation provides a computational framework in which the use of smelting equipment can be analyzed and optimized, leading to the development of alternative modes of operation. Much of the complexity of copper and nickel smelters is centered on the converter aisle. These converters operate in parallel, produce batches, and set the tempo for the downstream operations. In practice, smelter staff schedule daily operations to coordinate the smelting furnaces and converters with downstream operations. Thus, a realistic simulation of smelter operations, over hundreds of days, should incorporate converter scheduling algorithms as presented in this paper.

Jan 1, 2014

By P. Hr?enjak

Two groups of methods are usually used in design procedures of underground excavation of dimension stone: the analytical and numerical methods of analysis. In all of these methods the in situ rock mass strength represents the main problem. This is due to massive rocks in dimension stone deposits, consisting of large blocks of rock separated with particular discontinuities, for which the Hoek-Brown empirical criterion, developed for jointed rock masses, cannot be realistically used to estimate rock mass strength, especially for a particular block of rock mass or a particular pillar. On the basis of the regular underground excavation process of dimension stone by separating blocks with the flat jack application, we developed the in situ flexural strength testing method. We carried out numerical analyses and evaluation of uncertainty of measurement in order to validate the in situ flexural strength testing method. On the basis of very good validation results, as well as results of the in situ flexural strength testing of exploitable layers on the ?Kanfanar? quarry, we introduced a new coefficient of reduction, which can be used for correction of other strength parameters determined by laboratory testing for obtaining a realistic value of rock mass strength.

Aug 1, 2013

By S. Hobo, M. Yagisawa, T. Uchida, C. Tokoro, T. Kato

In this study, quantitative modeling was carried out for the treatment of simulated waste water containing As(V), Zn(II) and Hg(II) as toxic elements, and Fe(III), Na(I) and sulfate as coaxing ions. The objective was to predict the pH and residual concentrations of all the elements in solution after the neutralization/co-precipitation treatment. To accomplish this, the removal mechanism for As(V) and Hg(II) by ferrihydrite precipitation was first investigated for simulated waste water containing only As(V) or Hg(II). From the experimental results, it was confirmed that the removal mechanism involves not only surface complexation but also surface precipitation. However, surface complexation is the main mechanism for As(V) and Hg(II) removal to meet the target levels regulated in Japan. Next, the surface complexation model was constructed for the removal of As(V) and Hg(II) by ferrihydrite. The specific surface area and site density were determined from reference values proposed by Dzombak and Morel (1990). By comparing the experimental and calculated results, it was confirmed that our constructed model could successfully represent the experimental results. Furthermore, the surface complexation model was coupled with chemical equilibrium calculations and applied to the neutralization of simulated waste water containing As(V), Hg(II), Zn(II), Na(I), Fe(III) and sulfate. The constructed model could successfully represent the pH edge for As(V), Hg(II), Zn(II), Fe(III) and SO42- removal. In addition, the constructed model could represent the ion balance. Thus, our constructed model is useful to estimate the amount of neutralizer that is needed to achieve a target pH.

Jan 1, 2016