Search Documents

By Hiroyuki Sano, Hiroshi Chida, Katsuya Toda, Takafumi Sasaki

Saganoseki Smelter & Refinery is one of the largest copper producers in Japan to produce 450,000 tons of new copper annually. Saganoseki used to operate six PS converters with "4 Hot-2 Blow" scheme, but managed to change its operation to "3 Hot-2 Blow" scheme with four PS converters, while maintaining the same production capacity. To achieve the operational change, the following improvements have been carried out; 1) Extending service life from 220 to 350 batches, 2) Shortening cycle time by increasing the blowing rate and the matte grade, 3) Reducing environmental impact by applying sophisticated fugitive gas collection system and 4) Saving energy by waste heat boiler’s modifications. The operational change has been successfully executed, and results in drastic productivity increase and cost reduction. Currently, Saganoseki is maintaining the efficient and consistent operation with 4 PS converters. This paper describes the above-mentioned improvements for increasing productivity and the recent operational conditions of the PS converters.

Jan 1, 2015

By J. L. Jambor, E. J. Reardon, E. C. Appleyard, J. A. Cherry

Since the 1957 initiation of deposition of mill tailings at the Heath Steele mine, New Brunswick, periodic detailed studies of the tailings geochemistry and mineralogy have been conducted, thereby providing a unique opportunity to examine the geochemical evolution of a sulfide rich mine>tailings impoundment. When deposited, the tailings contained about 85 wt% sulfide minerals, 1 wt% to 3 wt% carbonate minerals, and 12 wt% to 14 wt% alumino silicate minerals. Mineralogical examination of samples of the tailings from deep in the impoundment indicates that little oxidation occurred prior to tailings deposition. The mill process-water deposited with the tailings was neutral to slightly basic and contained low concentrations of Cu, Pb, Zn and As. Sampling of the tailings five years after deposition indicated that sulfide-oxidation reactions, occurring near the tailings surface, had decreased the tailings-water pH and increased the concentrations of Fe, S042-, Cu, Zn and Pb (up to 10 000 mglL, 25 000 mg/L, 2.5 mg/L, 200 mg/L, and 4.5 mg/L, respectively). In 1975, ten years after decommissioning, the tailings could be divided into three zones: an upper oxidation zone in which sulfide oxidation is actively occurring, a hardpan layer, 15 cm to 20 cm thick, composed of tailings cemented by secondary Fe minerals, and an underlying reduction zone in which the tailings are relatively tin oxidized (Boorman and Watson, 1976). Chemical analyses indicated the presence of low-pH waters containing very high concentrations of SOi-, Fe, and other metals (up to 63 600 mg/L SO42-, 28 600 mg/L Fe, 10 mg/L Pb, 600 mg/L Cu and 4000 mg/L Zn), suggesting that there was a period of intense sulfide oxidation between five and ten years after tailings deposition. More recent sampling, conducted some 20 years after the end of tailings deposition, indicates that relatively little change has occurred in the last ten years, thereby suggesting that the hardpan layer has provided an impediment to the downward movement of dissolved constituents. Analyses of the tailings solids show increased accumulations of many metals at or near the depth of the hardpan layer. Evaluations of the long-term evolution of the tailings can be enhanced by comparison of descriptions of the tailings with descriptions of the gossan that overlay the massivesulfide orebody prior to mining. At Heath Steele, this comparison suggests that many of the mechanisms controlling the distribution of metals in the tailings will probably persist over geologic time.

Jan 1, 1992

By F. E. Patton

"IntroductionAT NORANDA, the strength of the ore and wall-rocks per-mitted mining in large open stopes. While some of the orebodies were small and could be mined out in one stope, in most cases their size was such that it was essential that ore pillars be left during the first stage of mining. In these cases, backfilling has been necessary for ground control and to facilitate the later recovery of the ore in these pillars.This paper discusses the development of the •backfill and •its use in pillar recovery.GeologyThe ore bodies at Noranda occur as replacement deposits in a block of rhyolite flows and breccias, bounded on the north by the Horne Creek fault and on the south by the Noranda Andesite fault. Mineralization consists of pyrite, pyrrhotite, magnetite, chalcopyrite, sphalerite, gold, and various tellurides.The main orebody is a massive sulphide deposit designated the 'H' orebody. It is elliptical in plan, measuring roughly 400 feet by 800 feet, and is divided into two zones -Upper H, extending from surface to the 1,500-foot level, and Lower H, from the 1 ,500-foot level to just below the 3,000-foot level.Mining MethodsOpen stope mining in both Upper H and Lower H zones has been fully described in previous publications (1). A brief review only of the mining methods will be given here."

Jan 1, 1952

By Y. Prevost, D. Verhelst

"A computer-assisted process control system for the Noranda Process Reactor Wa5 installed at the Home smelter in 1991. Operating as an advisory tool for the furnace operators, and using a flexible oxygen balance as the basic building block of the computer program, the new control system has helped to reduce the variability in the grade of the matte produced by 50% . The smelter is currently operating at a 72% copper matte, with a standard deviation of between 1.0 and 1.3, while treating a wide range of concentrates, secondary materials and scrap. Enhanced process control has allowed for longer reactor campaigns, and improved stability of the converting operation.This paper reviews the feed classification and blending practice used at the smelter, outlines the strategy of the new computer control system, and summarizes the benefits realized since the implementation of the system in early 1990.IntroductionUntil 1989 the Noranda Home smelter operated as a multi furnace smelter, at one time having three hot-charge reverberatory furnaces, and finally operating with one wet-charge reverberatory furnace and one Noranda Process Reactor. In 1989 the final reverberatory furnace was closed and the Reactor became the sole smelting vessel, treating around 750 000 tonnes of concentrate, secondary materials, and scrap per year. At the time of the start-up of theNoranda Reactor in 1973, the vessel was capable of treating 750tonnes per day of a heterogeneous mixture of copper concentrates, fluxes and secondary materials to produce copper in one operation. Through process improvements, and the introduction of additional oxygen in 1982(pannell and Mackey, 1988), the daily tonnage increased to 1800 tonnes by 1988. The operation had also been changed to produce a high-grade matte instead of copper. Figure1 illustrates the main features of the reactor, a cylindrical vessel which is charged at one end and tapped at the other. The matteis subsequently processed through Peirce-Smith converters and anode furnaces before being cast into copper anodes. Figure 2 outlines the progressive increase in the furnace smelting capacity. Over this period the percentage of secondary materials, and scrap feeds also increased to approximately 110 000 tonnes per year, or 15% of the total new feed input (Bedard et al., 1991). Now operating wholly as a custom feed operation, the Home smelter can treat over 2200tonnes per day of new metal-bearing material."

Jan 1, 1993

By Alex Henderson

The underground hard rock mining industry has had little change since the mobile equipment era began in the 1970s. Equipment has become larger and faster but has not kept pace with the following challenges: ? Improvements in safe production, ? Increasing demand for metals, ? Environmental improvements, ? Decreasing grades, ? Increasing depth of mining, ? More metal from underground vs. surface mining, and ? Energy and green house gas awareness. We are on the cusp of a new mining era and must rethink how underground hard rock mining must change in order to meet these challenges. This paper will show historical changes and propose a set of guiding principles for the next era of mining. Mining has changed over the last century. Initially mining was primarily an endeavor carried on by private companies with minor environmental controls and few social expectations other than employment. In the mid to later part of the century the mining industry was facing new challenges: deeper mines, the London Metals Exchange markets for pricing, and environmental concerns related to acidic rock drainage coming to the forefront. In today?s context, mining has evolved in complexity with the social and environmental aspects equally or surpassing the technical complexities such as expanding from mining hard rock to laterites, and mining lower grades or at greater depths. Nowadays, communities must be considered as partners, both locally and globally and the increased international visibility pushes the mining sector to take a more balanced approach to the business of mining (Fig. 1).

May 1, 2011

By J. P. Messervey

THE story of the efforts made by the Department of Mines of Nova Scotia in the search for and investigation of mineral resources for the Canadian war effort began in the spring of 1937. During the past five years, however, heavy enlistments in the Active Service Forces by employees of the mining industry of the Province caused a recession in the production of coal, salt, and other essential minerals required to keep industry rolling on a wartime basis. A marked increase was shown during the period in prospecting for 'strategic' minerals, not only by individuals but also by some of the foremost mining companies. The Provincial Government offered encouragement in this field of endeavour by the enactment of legislation whereby the prospector was enabled to secure the maximum area of ground in a prospecting license at a minimum of cost. The labour requirements on the ground staked, however, remained unchanged. The Nova Scotia Department of Mines continued active investigation of minerals vital to the war effort. These included fluorspar, barytes, diatomite, limestone, and coal. Fundamental knowledge concerning the geology and mode of occurrence of these minerals was accumulated and extensive diamond drilling was carried out on the promising occurrences. Work in these fields is being continued.

Jan 1, 1945

By Phillip Mackey, Elmira Moosavi-Khoonsari

L'industrie du cuivre traverse une période passionnante, marquée par une forte demande, de bons prix et l'ouverture de nouvelles grandes installations. L'année 2022 a battu des records de production de cuivre, ce qui laisse entrevoir un potentiel de croissance supplémentaire. De grands projets sont en cours, comme la technologie Double Flash à Manyar, en Indonésie, qui peut produire plus de 500 000 tonnes de cuivre par an. À Munda, en Inde, on a construit la plus grande usine de cuivre du monde, qui produit plus de 1 000 000 tonnes de cuivre par an en combinant deux phases. De plus, l’installation de cellules de flottation de dernière génération au Mexique, au Chili et dans d'autres pays témoignent de la volonté de l'entreprise d'utiliser les technologies les plus récentes [1]. L'importance du cuivre dans la transition énergétique est évidente, l'accent étant mis à la fois sur la croissance et sur la protection de l'environnement. Cela se traduit par le développement d'usines de premier ordre dédiées aux pratiques durables.

May 2, 2024

By Nichols. R. S.

"Surface coal mining production from Elk Valley and area in southeastern British Columbia began in 1913. Since 1970, five open-pit mines have been put into production: Westar Mining&apos;s Hanner and Greenhills Operations; Fording Coal&apos;s Fording River Operation; Byron Creek Collieries&apos; Coal Mountain Mine and Crows Nest Resources&apos; Line Creek Operation.ln 1983 these mines produced 14.9 million tonnes of raw coal at an average strip ratio of 4.9 bank cubic metres of waste to 1.0 tonne of raw coal. This is 70% of the estimated 21.1 M tonnes annual capacity .Multiple seams are recovered with truck/shovel and dragline equipment. There is a wide range of equipment types in use with a recent trend toward larger and more mobile equipment.Coal mining in Elk Valley involves advancing along strike in four steps: hangingwall waste removal; seam cleaning; coal recovery; and foot wall waste removal. Each mine is unique in its approach to these four steps but the truck/shovel methods can be categorized into three main groups: seam dips < 35 degrees as at Harmer, Fording and Greenhills; seam dips 35 to 50 degrees as at Line Creek; and seam dips >50 degrees as at Byron Creek. Dragline mining at Fording involves bath waste and coal removal by draglines."

Jan 1, 1984

By O. A. Ojo, N. Esmaeili

"The effects of brazing and use of composite powder mixture as interlayer material on hot corrosion resistance of brazed IN738 superalloy were studied. Brazing was observed to result in significant reduction in the hot corrosion resistance of the superalloy. However, application of composite powder mixture, which consists of additive superalloy powder, enhanced the hot corrosion resistance of brazed samples. It is also found that although the use of composite powder mixture increased hot corrosion resistance of brazed alloy, if the additive powder completely melts, which is possible during brazing, it can significantly reduce the hot corrosion resistance of the brazed joint. Elemental micro-segregation during solidification of the joint with completely melted powder mixture produces chromium depleted zones and consequently reduces hot corrosion resistance, since a uniform distribution and adequate chromium concentration is necessary to combat hot corrosion. This has not been previously reported in the literature and it is crucial to the use of composite powder mixture for enhancing the properties of brazed superalloys.INTRODUCTION Superalloys have been developed in response to the increasing demand for materials with higher resistance to corrosion and creep and also with higher mechanical strength at higher temperatures (Smith, 1981). Ni-base superalloys are predominantly used in manufacturing hot sections of gas turbine engine components. This is due to their high strength and corrosion resistance in extremely high temperature service environments which is typical for hot sections of gas turbine engines (Miglietti, 2009). The continuous demand for higher efficiency and output has resulted in the use of higher operating temperatures and gas pressure in modern gas turbine engines (Jahnke & Demny, 1983). Consequently, this has caused thermal and mechanical stresses which result in severe degradation and damage of gas turbine engine components due to creep, fatigue and hot corrosion (Zhang, Feng, & He, 2006). The decision to replace or repair damaged parts depends on the overall repair cost and expected life of the repaired components (Jahnke & Demny, 1983). However, in most cases, it is more cost effective to repair damaged parts rather than use a full replacement."

Jan 1, 2017

By Bo R. Arvidson

"New permanent magnetic alloys have recently opened up possibilities for development of unique mineral separators. These are now making several new applications feasible. In many cases where conventional electromagnetic-induced roll separators have traditionally been used, the new permanent magnetic roll separators may reduce both over-all capital costs and operation costs.The development of the next generation of extremely powerful permanent magnets, i.e. neodymium-iron alloys, is progressing rapidly and will affect the roll separator as well as another type of magnetic separator. Permanent Magnet Roll SeparatorDesign and FeaturesDiscs of permanent magnets interleaved with soft iron discs constitute the basic magnetic roll design (Fig. I). By enveloping the magnetic roll with a thin abrasive resistant belt (Fig. 2), even highly magnetic particles are removed.The first prototype roll utilizing the new magnets was shown to have approximately equal strength as induced magnetic roll (IMR) separators. Since the initial test roll, the new separator, called the PERMROLL® , has been made twice as strong with regard to magnetic force, that is, the magnetic flux density is determined to exceed 1.7 tesla (17 kilogauss), while the magnetic field gradient is more than twice the gradient than can be practically achieved with IMR."

Jan 1, 1985

By A. S. H. Kabir, I-H. Jung, J. Su, Yue. S., M. Sanjari

One of the major problems associated with conventional wrought magnesium alloys is the unwanted basal texture that forms during plastic deformation which generally does not change markedly after post-deformation annealing. Formation of precipitates on the recrystallized grain boundaries during annealing may affect the usual rotation of grains towards preferred basal direction resulting in texture weakening. In this study, Mg-Al-Sn alloy was hot compressed at 250°C and annealed at 350°C for various times. The initial as-deformed microstructure was partially dynamic recrystallized with dynamic precipitates on the grain boundaries. After annealing at 350°C, static recrystallization of the bimodal microstructure took place where at this temperature no static precipitates formed. The goal of this work was to study the effect of dynamic precipitation on the texture evolution during the annealing process. Texture evolution was studied during annealing by electron backscattered diffraction (EBSD) technique through a microstructure tracking process. It was found that precipitates on the recrystallized grain boundaries have significant effect on the usual rotation of the grains towards the basal direction, meaning significant texture weakening, which is beneficial for final mechanical properties.

Jan 1, 2015

By M. A. Bérubé

Le but principal de cette étude était de vérifier certaines hypothèses de nature minéralogique susceptibles d&apos;expliquer en tout ou en partie les variations importantes observées au concentrateur no 1 de Mines Gaspé quant aux performances du circuit B de broyage et de flottation. A cette fin, nous avons examiné six séries d&apos;échantillons prélevés lors d&apos;une campagne de mesures effectuée au cours de l&apos;été 1980. Ainsi, la capacité du circuit de broyage semble dépendre principalement devariation s dans les caractéristiques minéralogiqu es et texturales du minerai, par exemple du rapport grenat/quartz, le grenat ayant une influence néfaste sur le rendement de cette étape, contrairement au quartz . Quant au processus de concentration, la fraction du cuivre sous f orme de minéraux difficilement récupérés par flottation, en particulier des carbonates de cuivre, varie de façon significative dans le minerai, et cela peut certes expliquer en partie des récupérations parfois plus basses. Malgré ces variations important es de la composition minéralogique globale du minerai et de sa broyabilité, le degréde libération des sulfures de cuivre dans le produit de broyage dépend presque seulement de la granulométrie de ce produit. Afin de garantir des performances égales à l&apos;étape de concentration, il est fortement suggéré de contrôler cette granulométrie à un niveau constant.

Jan 1, 1984

By John E. Udd

I N Part I of this paper, Professor Morrison suggested that our technique of causing cracks to develop around openings in a sheet of photoe1ashc plastic is, in effect, a laboratory-scale rockburst. Our investigations have indicated that the location and direction of these cracks are predictable, and that their growth can be controlled. On several occasions, we have been able to cause these cracks to propagate sufficiently slowly to be followed, with the naked eye. In practice, the rate of growth, gradual or sudden, would depend upon rock properties. This part of the paper presents an analysis of the stresses surrounding the openings before and after failure and also this author&apos;s views on the causes and after-effects of cracking. An attempt is made to correlate the stress patterns with those deter-mined from pure mathematics. Considering that the openings, except for the central enlargement, are long apertures with somewhat rounded corners, they might be compared with elongated ellipses having axes ratios of about 20:1 or with

Jan 1, 1963

By S. Hussien, P. Somasundaran, P. Patra

"Rare earth elements (REEs) are essential for many applications in electronics, energy harvesting, and defense. The common resources for economic extraction of REEs are oxides such as bastnaesite and monazite, which are scarcely available in the earth’s crust. On the other hand, REEs are available in many clay and phosphate ores where REEs substitute Ca or Si in the mineral lattices or as physically adsorbed cations at negatively charged sites on the clay surface. While REE oxides readily dissolve in acid, making the chemical leaching of REEs an economically viable option, adopting a similar approach for leaching of silicates and phosphate ores is unfeasible because of significantly low REEs content in these ore deposits. Bio-leaching approaches are environmentally benign and economically viable. We investigated the bio-leaching (Acidothiobacillus ferrooxidans (Af) and the fungal Aspergillus niger (An)) of REEs from a phosphate ore, and examined the factors governing the leaching processes. Based on the shake flask leaching studies, an increase in surface area combined with an increase in pulp density (1-15 wt. %) was found to lead to an increase in the amount of REEs leached. In contrast, an increase in the surface area by reducing the particle size from 75 to 35 led to a decrease in the amount of REEs leached. These differing attributes are proposed to be due to the poor bacterial growth/activity with high F- ions in the leaching media, F- released from the edge-sites of the smaller particles. On the other hand, several advantages that associate with the Af bacterial bio-leaching processes relate to the media composition (Mg2+ and (NH4)+) and phenomena occurring at the electrical double layers of the mineral and bacterial- water interfaces. These studies suggested that leaching of particles occur in a layer-by-layer manner.INTRODUCTIONRare Earth Elements (REEs) are essential for many important applications, such as in electronics, energy generation, and defense. The common resources for economic extraction of REEs are typically carbonates such as bastnaesite and monazite, which are scarcely available in the earth’s crust (Y. Kanazawa and M. Kamitani, 2006). REEs are abundantly available in many clay and phosphate ores where REEs substitute Ca or Si of the mineral lattices. Conventional acid leaching of REEs from oxides is not economically feasible for clay and phosphate ores because of significantly low REE content (parts per billion) in these ores (Tian, J., Chi, R., Yin, J., 2010a; Moldoveanu G. A. and Papangelakis V. G., 2013; WK Goyne, LS Brantley and J Chorover, 2010). In some cases, REEs could be extracted from these ores via chemical leaching routes as they constitute reasonable amounts of REEs (0.1 - 1% REEs). A major challenge faced in general in chemical leaching processes (Chi, R., 1988) is the loss of REEs in the phosphate/gypsum precipitates/crystals, which are overcome in a step-by-step manner by sequentially removing impurities such as fluorine and calcium, including steps carried out at elevated temperatures. On the other hand, bio-leaching approaches provide environmentally benign and economical alternatives. Acidophilic bacteria are currently being used for industrial scale bio-leaching of Au/Cu/Ni from low grade ores. Studies on bioleaching of REEs from red mud (Al2O3) using Penicillium tricolor and Aspergilus niger (An), and, of bio-leaching (lab-scale) of phosphate rocks using Acidithiobacillus ferrooxidans (Af) have been reported (Boon, M., Heijnen, J.J., 1993; Qu, Y. and Lian, B., 2013). We conducted bacterial (Af) bio-leaching of REEs from a phosphate ore in shake flasks and columns, while examining the key factors that govern leaching kinetics."

Jan 1, 2016

By G. T. Lapidus, A. Garcés, O. J. Restrepo

"Colombian nickel laterites have historically been processed by pyrometallurgy. However, due to the depletion in ore grades, alternative processes are required. Hydrometallurgical processes, such as pressure acid leaching, have been proposed as alternatives to extract nickel from deposits with suitable characteristics. Such a leaching process requires high concentrations of acid to achieve acceptable extractions, and is not selective. In this study, an alternative aqueous alkaline glycine system has been employed to evaluate the leaching behaviour of a Colombian nickel laterite which contains 1.15% Ni, 0.12% Co and 41.1% Fe. Additionally, the effect of the addition of chloride ions, the use of a reducing agent and the application of a pre-treatment to improve the extraction of nickel were evaluated. Extractions of 4.63% Ni, 42.16% Co and 0.33% Fe were obtained using a 1M solution of glycine at pH 9. In addition, an increase in nickel extraction from 4.63% to 25.68% was achieved by applying a pre-treatment to the sample. The results show that even though nickel dissolution was much slower than in acid leaching, it was selective over other metals such as iron, proving the proposed method to have potential as a process for the extraction of nickel from Colombian laterites.INTRODUCTION Before 2010, most of the industrial operations used pyrometallurgical processes for the extraction of nickel, mainly in saprolitic regions of deposits, with greater contents of the metal. Nevertheless, due to the gradual depletion of such deposits, different hydrometallurgical processes have been studied as alternatives to process those nickel laterites with low grade and those which present problems of refractoriness due to the presence of acid consuming materials (McDonald & Whittington, 2008; Oxley & Barcza, 2013; Wang et al., 2012). However, such leaching processes require high concentrations of acid to achieve acceptable extractions and they are not selective. Facing lateritic nickel ore deposits containing high levels of acid consuming materials, an alkaline leaching medium becomes an advantageous alternative over acidic media, due to the increase in selectivity and decreased corrosiveness and reagent consumption (Tanda, Eksteen, & Oraby, 2017). Unlike conventional acidic reagents used for metal recovery, alkaline reagents can selectively dissolve the desired metal, leaving in the solid residue other elements such as iron, magnesium and aluminum, which are problematic in subsequent stages of metals separation and recovery. Furthermore, there are no serious corrosion problems associated with alkaline leaching, even at higher reagent concentrations, or at elevated temperature and pressure (Ntumba Malenga, Mulaba-Bafubiandi, & Nheta, 2015)."

Jan 1, 2017

By Farzad Khodabakhshi, Adrian P. Gerlich

"Multi-pass friction stir processing (FSP) was performed to fabricate a new Al-Mg-Graphene nanocomposite. Microstructural developments and distribution of graphene were studied by using electron backscattering diffraction (EBSD) and transmission electron microscopy (TEM) analysis. In the stirred zone (SZ), grain structure was refined down to about 2 µm attributing to the operative dynamic restoration mechanisms and the locking effect of graphene phase. As a result, the yield strength of Al-Mg alloy was improved more than two times due to incorporation of graphene nano-sheets. Also, the indentation hardness resistance of nanocomposite was increased up to ~60%.INTRODUCTION Aluminum-matrix nanocomposites have garnered significant in recent years due to their superior performance and potential advantages for several industrial applications including the automotive and aerospace sectors. Among various reinforcing nano-materials, carbon-based structures featuring sp2 or sp3 hybridization bonds have been found to offer considerably improved physical and mechanical properties. Such carbon allotropes form at micro- and nano-scales including; graphite, carbon nano-tube (CNT), nano-fiber, and graphene. The potential of two-dimensional (2D) carbon materials was introduced in 2004, with the development of graphene as an alternate 2D allotropic form of the carbon structure with a honey-comb lattice at the atomic-scale. It has been shown that it is currently among the strongest materials ever tested with an intrinsic tensile strength of 130 GPa and Young’s modulus of 1000 GPa, and also offers unique thermal and electrical properties.To fabricate metal-matrix nanocomposites reinforced by graphene nano-sheets with typical metallurgical processing techniques, some attempts have been reported in the literature for various solid-state techniques including; hot rolling, mechanical alloying, and friction stir processing (FSP) of pre-cast plates or surface dispersed graphene oxides. The main challenge in those methods was to facilitate the considerable high temperature and pressure for attaining a uniform dispersion of the nano-sheets during the consolidation process. In most cases, significant difficulties have been reported in obtaining a uniform dispersion of graphene within the metal matrix. Among various techniques for production of metal-matrix nanocomposites, FSP has attracted significant attention as a method of surface modification since it was first reported by Mishra et al. In this process, a non-consumable rotating tool is plunged into the surface of material for the aim of microstructure modification. Extreme material plasticity is induced without melting as a result of friction between the tool and workpiece. Frictional heating and severe plastic deformation induced by the FSP process enables metal matrix nanocomposite fabrication by softening the base material and mechanical stirring to disperse the reinforcing nano-materials into the matrix."

Jan 1, 2017

By W. G. Scott

IT IS APPROPRIATE that your Institute should have chosen, for its 1956 Annual General Meeting, the Capital City of a province which is making such rapid advances in mining. The railway industry is proud to be playing an active role in this development, expenditures on equipment and railway construction in the Province of Quebec alone in recent years being in ?excess of a quarter of a billion dollars. In looking up some background material for this address I ran across a definition of a mine by Mark Twain, the great American humorist, which I thought might amuse you. He said that a mine was "a hole in the ground owned by a liar". I am sure that if he were alive to witness the enormous value attached to Canada&apos;s mineral resources today he would quickly change his definition. Canada&apos;s postwar record of mining development has been staggering in its variety and enormity. Historically, only the ?construction of our transcontinental rail ways outranks the largest of three of these development projects - the aluminum undertaking at Kitimat; the Quebec-Labrador iron ore deposits ; and the petroleum and natural gas developments in Wes tern Canada.

Jan 1, 1956

By H. Craig Boyle, Craig H. B. Leitch

"The Trout Lake stockwork molybdenum deposit is located in the Selkirk Mountains of British Columbia, 50 km southeast of Revelstoke. The property is being explored by a joint venture between Newmont Exploration of Canada and Esso Minerals Canada.The deposit is associated with a small granodiorite stock of Upper Cretaceous age (76 Ma) which has variably altered the surrounding schists, argillites and marbles of the lower Paleozoic Lardeau Group to hornjelsic biotite schists and skarn. The intrusive is composed of a small stock and an intersecting network of northeast- and northwest-trending dykes at surface that coalesce downward into a larger stock. There are two main phases of intrusion, with an earlier quartz porphyritic granodiorite cut by an intra-mineral ""quartz diorite"" porphyry. A strong sub-vertical north-trending fault controls the distribution of the mineralized stock work and displays post-mineral movement.Molybdenite, accompanied by pyrite and pyrrhotite, is mainly present along the margins of veins in a well-developed quartz stock work, but occasionally is strongly disseminated in microfractured intrusives. The stock work is strongest in and around the contacts of the intrusive and its apophyses, and occurs over a vertical range of more than 1,000 m. As defined by the 0.10% MoS] contour, the main mineralized zone is up to 300 m long by 200m wide. Preliminary drill-indicated reserves, currently being revised, are approximately 50 million tonnes of 0.23% MoS2, within which are several zones of higher-grade material. Hydrothermal alteration, as defined by quantitative X-ray diffraction studies on composite core sections, is composed of a central quartz/K-feldspar/albite/minor biotite zone coincident with molybdenum mineralization, which is overlapped by a slightly later, antipathetic quartz/ sericite/pyrite zone. Ankeritic carbonate is also a common alteration mineral, but only traces of fluorite, and no topaz or sulfosalts, have been observed. Analysis for trace elements such as Sn, W, Bi, Sb, As, Hg, U, Ag, Au, Mn, Cu, Pb, Zn and F has been limited except for Sn and W, which appear to be zoned inside and outside the Mo zone respectively; the other elements do not show detectable patterns thus far."

Jan 1, 1983

By Robert B. Parsons

"With several hoots of the whistle, Canada&apos;s fiscal engineers are once again cranking up the income tax locomotive, in an effort to inject new stimulus into a stubborn economy. And once again, additional gears, wheels, levers, and other mysterious part s are being added to the already complex machinery in order to accommodate the new push.This time, a significant new mechanism involves a major overhaul and expansion of the investment tax credit system.Although the shiny new devices have considerable appeal to a certain group of potential passengers, one wonders if all of the renewed chugging and huffing is on the right track.IntroductionAs indicated in Tax Notes in the July 1983 issue of CIM Bulletin , the April 19, 1983 federal bud get introduced a number of new measures which would permit investment tax credits and research and development deductions to "" flow through "" from a corporation to another taxpayer."

Jan 1, 1984

By A. G. Darnley

"IntroductionTHE PURPOSE of this paper is twofold. Firstly, to drawn attention to recommendations which have been accepted by the International Atomic Energy Agency concerning radiometric reporting methods and calibration in uranium exploration, and secondly to emphasize the benefits that- will stem from adopting them. These recommendations are contained in an IAEA Technical Report, No. 174, which has been prepared with the intention of serving as a general guide to the subject. The existence of this specialized report is likely to be unknown to most of those who can benefit unless it is given some publicity by an organization such as the CIM. The recommendations were prepared by a small international committee consisting of Dr, P. H. Dodd , U.S .A. , Dr. R. L. Grasty. Canada, Dr. L. Levborg, Denmark, Dr. M. Matolin, Czechoslovakia , Dr. S. D. Simov, Bulgaria, and the writer.The fact that there are standard scientific units of mass, distance and time is taken for granted, It is also accepted that the type of instrumentation used to measure one of these parameters is irrelevant to the way the measurement is reported. Geophysical parameters such as magnetic field strength and gravity have generally accepted units, the gamma and milligal, which are defined in SI terms. These units are employed irrespective of the operating principle, or manufacturer or organization involved in the measurement."

Jan 1, 1977