Search Documents

By P. B. Demarsh

"Location: - Mine village of Perron, 11 miles east of Val d’Or in northwestern Quebec.Life; - Started production 1932, ceased 1951.Ore: - Flat lying quartz tourmaline veins within granodiorite. Gold values related to coarse segregations of pyrite. Specific gravity 2. 80.Capacity: - 30 tons 1932-35; 125 tons 1935-37; 350 tons 1937-51.Assay: - Heads 0.21 to 0.34 oz. per ton. Grade obtained by mining 600 tons daily, sorting belt reject 250 tons, balance to milling; tailings loss 0.003 to 0.005 oz. per ton; extraction 9 8. 5%.Grind: - 70% minus 200 mesh. Detention time 26 hours.Treatment: - Cyanidation process.Reagents: - Per ton, aero cyanide (NaCn) 0.36; unslaked lump lime 1.50; zinc 0. 03; lead acetate 0. 006; steel consumption 2. 50.Water: - Equal mixture of swamp creek water and underground seepage.Cost: - Per ton, sorting and crushing 0.21; grinding 0.31; cyanidation 0.11; filtration 0.05; precipitation 0.02; miscellaneous 0.22; total 0.92.Power: - Hydro-electric, 25 cycle, 12, 000 volts reduced to 550 volts.Labour: - 95% Maritime and European, balance Quebec and Ontario.Tailings: - Absorbed over large swampy area on barren mining claims.Personnel: - 1 7 men including supervision.Flow sheet: - Canadian Mining Manual 1947"

Jan 1, 1966

By Trygve Høy

"Important stratabound lead-zinc deposits in southeastern B. C. occur in rocks that range in age from Proterozoic Helikian to Middle Cambrian. The Sullivan deposit, and similar but smaller deposits in the Sullivan area are the only important deposits that occur in clastic rocks with little carbonate content. The highly deformed and metamorphosed Shuswap deposits, of probable Hadrynian to Helikian age, are in mixed marble, calc-silicate gneiss and pelitic schist assemblages, rocks transitional between clastics and carbonates. Deposits in younger rocks, such as the Kootenay Arc deposits in the Lower Cambrian Badshot-Reeves Formation and the Monarch -Kicking Horse deposits in Middle Cambrian dolomite, are hosted by platformal carbonate rocks.An important regional control for the distribution of deposits appears to be a northeast-trending tectonic zone that crosses the Rocky Mountains and the Purcell Mountains just south of the Sullivan area, and projects southwestward toward the Salmo camp at the southern end of the Kootenay Arc. Pronounced northeast-trending gravity and magnetic anomalies, basic volcanism of Hadrynian age (the Irene volcanics west of Creston) and a preferred alignment of Mesozoic granitic rocks indicates that the zone coincides with deep crustal structures. Within the zone are dramatic and abrupt thickness and facies changes in Hadrynian Windermere rocks and lower Paleozoic rocks, and on the east side of the Rocky Mountain Trench in Helikian Purcell Supergroup rocks, indicating that block-faulting was active intermittently within the zone from Helikian through to lower Paleozoic time. Right-lateral and reverse movements occurred on northeast-trending tear faults within the zone in Mesozoic time."

Jan 1, 1982

By K. Lambrych

Hydrometallurgical equipment used to extract and refine copper and other metals is exposed to extremely corrosive chemical environments. These systems must be fabricated from materials that are durable against corrosion, meet exacting mechanical requirements, and perform economically over the life of the mineral processing plant. In several recent large hydromet projects, fiber reinforced plastic (FRP) has been shown to provide equal if not superior durability relative to alternative materials of construction. This paper will compare corrosion performance and cost of plant equipment fabricated with corrosion resistant alloys, rubber lined steel, and FRP made with Epoxy Vinyl Ester thermoset resins. Case histories for FRP piping, storage tanks, extraction vessels, and electrowinning cells combined with laboratory-based corrosion studies will be reviewed to demonstrate how FRP materials are selected for hydrometallurgical equipment. Specific examples from projects such as El Boleo, Long Harbour and others will be used to demonstrate how the versatility of FRP allows for remote fabrication of durable corrosion-resistant large-scale equipment for hydrometallurgical refinement of copper and other metals. INTRODUCTION Fiber reinforced plastic (FRP) began to emerge as a material of construction for corrosion service in many industrial processes in the late 1950s because of its ease of use and overall performance. Corrosion resistant (CR) FRP, as an alternative construction material to alloys, rubber and tile linings, grew steadily in following decades. The aggressive operating conditions associated with hydrometallurgical processes typically require materials of construction that can withstand acids and acid chlorides at temperatures up to 90°C, sometimes higher. Common metallic materials of construction, such as carbon steel, are not compatible with these conditions. High nickel alloys are capable of meeting performance requirements, but often at a high cost. In many cases FRP mining equipment based on epoxy vinyl ester resin (EVER) offers durability, long service life and lower maintenance costs. Through demonstrated performance and decades of case histories, more and more design engineers are confidently specifying FRP as the material of construction for new mineral processing equipment.

Jan 1, 2019

By G. Stafford Whitby

N ATURAL gas is found in several provinces of Canada, particularly Ontario, New Brunswick, and Alberta. The largest producer is Alberta, and there the most important field is the Turner Valley, where some low-gravity crude oil and naphtha are associated with the gas. Last year there was produced from the Turner Valley field an average of 3,462 barrels, or about 450 tons, of oil a day. The gas flow from the wells in this field bears such a high ratio to the oil which comes from them that, despite the enforcement of a measure of conservation, it amounted to the vast quantity of 6,000 tons a day, or more than 2,000,000 tons a year. Prior to the application of any conservation measures, the gas flow was at one time of the order of 12,000 tons a day. The heat content of one ton of the gas is almost equal to that of two tons of coal. A certain amount, say, 10 per cent," of the gas is used in Calgary and surrounding towns and in re-pressuring the Bow Island gas field, but the greater part of it goes to waste. What are the possibilities of making use of this waste gas, in whole or part? The possibilities of using it profitably as fuel for domestic and industrial purposes have undoubtedly been carefully considered by the Company which now distributes a part of the gas to cities and towns in Alberta. But the relative sparness of the population and the cost of pipe lines makes such possibilities strictly limited. There are, however, distinct possibilities of making use of at !east a part of the gas for the production of a variety of chemical products and of liquid motor fuel. The present paper is devoted to outlining some of these possibilities. About three-quarters (by weight) of the Turner Valley waste gas consists of methane, the lightest and, chemically speaking, the simplest of hydrocarbon gases. The remaining quarter consists of heavier hydrocarbon gases-ethane, propane, and butane. Formerly, naphtha was separated from the well gas by a simple process of self-refrigeration. The gas coming from the wells at a pressure of, say, 1,200 to 1,800 lb., was passed through simple cylindrical vessels fitted with baffles and known as 'separators'. The pressure was allowed to drop to, say, 300 lb. in the separators, and the cooling effect secured by this expansion brought about separation of the naphtha. The naphtha thus obtained was 'wild', that is, it had a high vapour pressure owing to the presence in it of dissolved and liquefied gas. In order to reduce the vapour pressure to a level at which the naphtha could be shipped, this gas was removed either by distilling it out through a 'stabilizing' column or, according to the practice at many wells, merely by allowing the naphtha to 'weather' in open tanks (heated by coils if necessary) until the gas had been driven off in to the air.

Jan 1, 1936

By Maureen Jensen

For mining companies looking to establish a strong North American presence, raise their profile or finance and position themselves for future growth, there is no other destination in the world that can offer a mining company the same opportunities as Canada whether you are an established blue chip or promising junior. Despite historically poor world commodity markets and shaky investor sentiment towards junior explorers caused in part by fallout from the high profile Bre-X fraud, Canada continues to shine as the undisputed mining finance capital of the world. Our natural riches and mining history go a long way to explain Canada's international prominence in mining finance. Canada has actively created and maintained one of the most integrated national frameworks to support mining ventures of all kinds. Our diverse industry, from one-person grass-roots explorers to mining industry giants, is one of our main strengths whether your company is Canada-focused or internationally active. The mining industry continues to be a vital contributor to the Canadian economy, contributing $26.2 billion in 1997 or 3.8% of national GDP, and is the second largest earner of foreign exchange. Industrial mineral companies are a very important part of this strength. These companies require a continuing access to capital to ensure that they can continue to compete and the globalisation of the Canadian mining industry has affected this industry just as much as it has affected every other industry in Canada.

Jan 1, 2001

By Alan Bauer

IN RECENT PAST YEARS, the mining industry has expanded rapidly and mining engineers have not been generated in sufficient numbers to sustain this growth. Canada has not been alone with this problem, which has resulted in considerable soul-searching as to what the solution might be. Because of the unfavourable economics of running small departments such as mining, metallurgy, ceramic engineering, etc., one approach in some cases has been to put these departments together to form a department of mineral science which now has a broader base structure. Another solution has been the "conversion kit" program which has been conducted both at universities and in industry. At universities, such programs have consisted of converting graduates of other engineering disciplines into mining engineers. In some of the large mining corporations, extensive training programs have been used with the same aim.

Jan 1, 1972

By Jean-Luc Collins

"This new tool can be used as a quick guide f or the assessment of the potential economic wealth of any risky capital project. It does provide an unambiguous recommendation of the type ""go or no go"" to the decision-maker simply by comparing two different ratios profit/investment. One ratio determines the minimum value required to at least break even while the other measures a probable value based on the asymptotic theory of statistical extremes.Its application is briefly illustrated by means of an underground gold mine extension project, an oil sands mine project and a polymetallic open pit project.Once a favourable recommendation has been obtained then a detailed ""cash flow after taxes"" analysis can be carried out for the project.IntroductionMany tools are used in financial decision-making such as the payback period, the discounted cash flow, the internal rate of return and the wealth growth rate (Berry , 1971).These tools are useful and meaningful in evaluating normal projects closely related to regular business where the number of assumptions made is usually very small and where the cost of capita! is usually selected as a discount rate or a hurdle value. In situations where a significant number of assumptions have to be made,two problems can emerge, namely:I. the risk involved is underestimated leading to a potential financial disaster; or2. a good opportunity is lost because the approach used in evaluating the project is too conservative.Each assumption has its own degree of uncertainty and it is well known that combining uncertainties together can lead to a total uncertainty of critical proportion. The easiest way to account for risk is to increase the discount rate or the hurdle value, but this approach alone is quite subjective and can easily lead to the problems described above."

Jan 1, 1993

By J. Zollinger, J. R. Kennedy, J. H. Park, D. Daloz

"In order to improve the properties of cast Ti-Al alloys to replace Ni-based superalloys past the low pressure stages of aircraft engines investigations into inoculation for grain refinement were carried out. Previous work showed isomorphic self-inoculation using Ti-Al-Nb particles was effective for grain refinement, however the relatively fast diffusion of Nb in Ti-Al make it difficult to observe the mechanism of nucleation. An alternative alloy was developed in the Ti-Ta system for isomorphic self-inoculation, maximizing the Ta content to improve the particles survivability in the melt. The powder processing produced comparatively small inoculant particles which dissolved, however larger particles were seen to survive solidification. The density difference between the inoculant particles and melt resulted in an inhomogeneous mixing of the particles and the melt with larger particles found near the outer edges of the ingots. Variations on particle size and interaction time between the inoculants and the melt resulted in the Ti-Ta inoculant reducing the as-cast equiaxed grain size by a factor of two compared to non-inoculated samples as well as increasing the equiaxed fraction in the ingot.INTRODUCTION Lightweight metals are of particular interest in aerospace applications. The hot sections of turbines are dominated by blades made of nickel based superalloys. Recently the GEnx turbine introduced TiAl blades in the last low pressure stage of the turbine to reduce weight and improve fuel efficiency (Kim & Dimiduk, 1991). In order to carry these benefits deeper into the turbine the high temperature (>800oC) properties of the alloys must be improved. Current grain refinement methods to improve properties rely on boron additions which may not be applicable for all blades as brittle precipitates may be formed during processing (McCullough, Levi, Mehrabian, & Hyman, 1991). A novel grain refinement process was previously introduced called “isomorphic self-inoculation” using Ti-Al-Nb particles to successfully grain refine TiAl (Kennedy, Zollinger, Bouzy, & Daloz, 2016). In order to better understand the mechanism of this process an investigation was carried out using the same process but with a Ti-Ta alloy which is more stable in the TiAl melt than the Ti-Al-Nb."

Jan 1, 2017

By Moatassem Abdallah

Buildings in the United States account for 72% of electricity consumption, 40% of energy consumption, 13% of water consumption, 39% of carbon footprint, and 30% of waste output. In order to minimize these negative environmental impacts, many public and private owners are requesting that their buildings be more sustainable and certified under the widely known programs such as leadership in energy and environmental design for existing buildings (LEED-EB). To accomplish this, buildings are increasingly integrating green building measures including energy efficient lighting, motion sensors, thermal pane glass, geothermal heat pumps, EnergyStar rated HVAC systems, photovoltaic systems, and wind turbines. This research paper presents the development of an automated decision support system (DSS) that is designed to optimize the selection of green building measures which can be used to upgrade existing buildings. The developed DSS incorporates two optimization models that are capable of (i) minimizing the total upgrade costs required to accomplish a specified LEED-EB certification level such as silver or gold; and (ii) maximizing the number of accredited LEED-EB points within a specified budget of upgrade costs. The DSS is designed to identify a set of optimal upgrade decisions that accomplishes these two optimization objectives. An application example is used to illustrate the capabilities of the DSS and to validate its result.

Aug 1, 2013

By S. H. Logan

Mr. B. Neilly: A week or so ago the Secretary was good enough to forward me an advance copy of this paper by Mr. Logan and it was suggested that I comment on it at this meeting. At that time I was not very certain that I would be here, so I committed my thoughts to paper. As a matter of courtesy to Mr. Logan, I sent him a copy of my proposed remarks and I would like to give you just what I sent to him. Appreciating fully Mr. Logan's ability and many sources of information, one naturally hesitates to question anything seriously set forth as his considered opinion. Neither does one of my political stripe like to accuse him of being too 'conservative.? However, in places his paper reminds me of another general manager of a Canadian bank. While I was still Secretary of the Ontario Mining Association, this general manager wrote asking for our forecast on the current year's mineral production, stating that he proposed to refer to such production figures in his annual address to his shareholders. The request was considered very complimentary to the Ontario Mining Association and, in my opinion, justified a great deal of serious study and effort. Finally, the estimate was prepared and forwarded, showing a modest increase over the previous year's total. Picture our surprise and chagrin on reading his address to find that he predicted not an increase but, if you please, a decline of over $10,000,000. Before I cooled off I wrote asking the basis of such a prediction and got a reply to the effect that men in his position had to be ultra conservative in picturing the future.

Jan 1, 1931

By Qingxia Liu, Mingbo Zhang, Hongbo Zeng

The shortage of freshwater has been a major challenge for mineral flotation in arid areas. When using high salinity water, certain electrolytes are detrimental to flotation while others can improve the flotability of minerals. In this paper, the flotation behaviors and contact angles of pyrite in both Milli-Q water and high salinity water were investigated using different collectors at various pH levels. Results show that the thionocarbamate has a less affinity to pyrite in different solutions under mildly alkaline conditions as compared with potassium amyl xanthate (PAX) and N-isopropoxypropyl-N’-ethoxycarbonyl thiourea (iPOPECTU). At high pH levels, the slime coating on pyrite surfaces, which is caused by colloidal precipitates of magnesium and calcium ions in seawater, was confirmed by SEM, EDX and in-situ zeta potential measurement. The slime coating of colloidal precipitates on mineral surfaces led to low recovery of pyrite at high pH levels. The study of flotation behavior of pyrite in high salinity water improves our fundamental understanding of mineral flotation in seawater.

Jan 1, 2015

By Ian Hattie, Mark R. Wilson, T. Kurtis Kyser, Brian W. Janser

Petrographic, chemical and isotopic compo itions of auriferous and non-auriferous quartz vei ns from the Sta r Lake and Flin Flin-Amisk Lake areas of northern Saskatchewan indicate diver e origins fo r the fluids associated with gold mineralization. In the Sta r Lake area, the metavolcanic , Star Lake pl uton, and heared mafic dikes have retained their original igneous 81 80 values. The 81 80 value of quartz from mi neralized veins vary by I per mi! and range from+I0 to+IJ. The only quartz ample having a 81 80 value outside th is range came from a vein not associated wi th a dike or gold mineralization . Quartz from the Star Lake pluton has identical 8180 value to the qua rtz from mi neralized vei ns which suggests that the vei ns and the pluton are related to imilar proces es. The diffe rence in 81 80 values between mi neralized and barren vein may erve a a potential exploration tool in this area. Because o34S val ues of a limi ted number of amples of pyrite from gold-bearing quartz vei ns at Star Lake correlate directly with gold content. the gold may have been syngenetic with the su lphur and the 834 value may be useful for exploration . 8180 values of co-existing quartz, calcite, and amphibole in the veins from Star Lake indicate that isotopic disequilibrium among the minerals is common, but the val ues also record a high temperature of formation (ea . 500°C) involvi ng a component of magmatic fl uid. TheoD value of hydrou mineral from Star Lake retain their original igneous values but whole rock values are generally much lower, an effect attributed to interaction of the minerals with a late meteoric water. In the Fl in Flin-Amisk Lake area, auriferou and barren quartz veins formed from a mixture of hydrothermal and metamorph ic flu id at lower temperatures (ea . 350°C) than those at Sta r Lake. Becau e there i no apparent correlation between 8180 values of the quartz with gold content or relative age of the vein , nor between the 834S val ues of pyrite and gold content, table isotopes appear limited as an exploration tool in the Fl in FlonAmisk Lake areas.

Jan 1, 1986

By P. Condori

Palabora Mining Copper (PMC) has two autogenous mills that have been in operation since 1976. The mills were originally designed to treat 30 000 t/d of open cast copper ore in a closed circuit with cyclones. As the ore body went deeper the open cast method of mining was changed to block caving, a consequence of this was the dolerite content (hardest barren material) increased significantly, increasing the production rate of pebbles and thus reducing the milling capacity. In order to cope with the increased ore hardness and to increase mill capacity, a second ball milling stage and pebble crushing were incorporated to the circuit. The above actions created new challenges to the circuit operation and bottlenecks in different areas of the milling circuit. This paper reports the holistic work performed on the Palabora autogenous milling circuit including the implementation of a mill constraint control scheme, the implementation of a pebble removal system from the circuit and a new circuit configuration. The achieved plant stability and increment of ore throughput are also reported in this paper.

Jan 1, 2012

By R. Hendricks

"IT IS a pleasure for me to appear before yon today and to have this opportunity of reviewing with you recent developments in the world lead and zinc industry. To provide essential background material, I propose reviewing the period from 1950 to the present, a period which has undoubtedly been the most hectic in the long history of the industry.In capsule form, the pattern for this period is one of repeating cycles of boom and recession, of failure through research to develop adequately new markets and new uses for lead and zinc, of surplus production and growing inventories, of price instability, and lastly, of an abdication in some sections of the industry of responsibility for control of its own destiny by turning to governments for support in time of stress. This is not a pretty picture but, as the 1950 decade ends, there are signs of a new maturity and of a growing determination on the part of the industry to put its own house in order.The difficulty suffered by the world's lead and zinc industry in the current decade originated with the support extended to it in 1950 by the U.S. Government at the time of the Korean conflict. Recalling the shortage of base metals in World War II and fearing that the Korean conflict might develop into World War III, the U.S. Government in 1950 adopted a policy to encourage the production of lead and zinc, both domestically and abroad by means of development loans and long-term floor priced purclu.se contracts."

Jan 1, 1960

By B. C. Legg, G. L. Tiley

"Many of the ore bodies presently being developed are in remote locations and are, or will be, served by electrical power supply systems of limited capacity.The largest single components of the electrical systems of an underground mine are usually the production hoist drives; the power demands of these drives vary continuously throughout each hoisting cycle.Before 1970mine hoists were driven by either wound rotor induction motors or DC motors in conjunction with motor generator sets.Static Power conversion equipment now costs less to purchase and install and is claimed to be more efficient than motor generator sets. On the debit side, however, it can adversely affect the hoist motors, it operates at relatively low power factors, and it produces harmonic currents.This pa per discusses the effects of static equipment on both DC motors and AC power systems, and evaluates the relative consumption of the three classes of drives."

Jan 1, 1993

By M. Bryson, A. E. Brady, W. Dawes, G. Beer, N. Sehlotho

Mkango Resources Limited is developing the Songwe Hill Rare Earth Element Project in southeast Malawi. Since being awarded the exclusive exploration licence for the project in January 2010, Mkango has completed an extensive work programme including detailed mineralogical studies, geological mapping, geochemical sampling and trenching, environmental and social studies, two phases of diamond drilling, and extensive metallurgical test work. In October 2012, the company announced a NI 43-101 compliant mineral resource estimate comprising an Indicated resource of 13.2 million tonnes grading 1.62% total rare earth oxides (TREO) and an Inferred resource of 18.6 million tonnes grading 1.38% TREO. The Indicated mineral resource estimate formed the basis for commencement of the Preliminary Feasibility Study (PFS). The mineralogical program identified the fluorocarbonate mineral, synchysite, and the phosphate mineral, apatite, as the primary rare earth element (REE) bearing minerals. Extensive flotation testwork conducted at Mintek in South Africa has resulted in an effective regime to increase the REO grade 2.6 times. Initial leaching testwork by Mintek identified that a selective hydrochloric acid (HCl) leach can target the gangue minerals with minimal REE dissolution. Recent testwork undertaken at Nagrom in Western Australia has expanded on this work to develop a two stage HCl leach process incorporating HCl recycling. A downstream processing route of purification and cerium rejection to produce a cerium depleted high grade REE concentrate suitable as feed to a separation facility is proposed.

Jan 1, 2014

By M. J. deBastiani

The uranium producing division of Denison Mines Limited operates a 6,000-ton-per-day integrated mining unit in the Algoma area of Ontario. The property is located approximately one and one-half miles from Highway I 08, eight miles north of the town of Elliot Lake. The property was staked in 1953, diamond-drilled in ?late 1954 and 1955, and put into production in 1957. Since that date, the operation has produced $250,000,000 worth of uranium oxide from approximately 11,000,000 tons of ore milled, and paid $18,000,000 in dividends to its shareholders. The operation employs about I000 people, and monthly operating costs are approximately one million dollars. From these figures alone, it is obvious that it was necessary to develop and institute an adequate set ?of controls for effective management at all levels of supervision over a period of four years, a system of production and cost control was developed that enables us to effectively measure the pulse of the various phases of the operation at any given time.

Jan 1, 1963

By Rakesh Kumar, Rajabrahma K., A. K. Verma, V. Mukesh

"In this study, laboratory investigation as well as numerical investigation is carried out to ascertain the transition from one mode to another for Semi-circular bend setup. Laboratory investigation is carried by varying the span length (s/2R); crack length (a/R); notch angle (a); and notch thickness (t). The specimen consists of cement, sand and water mixture in a ratio of 1:1:0.5 by weight and are prepared as per the ISRM standards (2014). Tests are conducted by a servo controlled universal testing machine at a strain rate of 0.2 mm/ min. The results are collected in terms of failure load, crack mouth opening displacement (CMOD) and images of crack initiation and propagation.Image analysis of laboratory tested samples shows that crack initiates at the notch tip when the notch inclination angle is 0°. As the notch angle increases (i.e. 30° and 60°) the fracture begins to initiate behind the notch tip. The direction of crack propagation in front and back side of the sample is same for notch inclination angle is 0° whereas it differs more and more as crack inclination increases. The transition represents the change in mode of failure from mode I (0°), mode II (30°) and mixed mode I/II fracture (60°).Finite element method used to find the transition based on MTS failure criterion. The inclination of notch is varied like 40, 42, 44, 45, and 50 deg and FEM analysis shows that the transition from mode-I to Mode-II take place at 49 deg. The same procedure can be extended to find the transition from mode-II to mode-III."

Jan 1, 2015

By J. P. Jylhä, A. Jokilaakso

The Outotec Flash Smelting process is widely used in primary copper production. A layer of slag on top of matte (copper–iron sulphide melt) creates a barrier through which matte droplets descend. Droplets of different sizes settle through the layer at different rates, which increases possibility of copper losses as smaller matte droplets may be removed with the slag. In this work CFD-DEM (computational fluid dynamics – discrete element method) coupling was used to simulate matte droplets settling through the slag during slag tapping. Discrete droplets and slag flow were simulated with DEM and CFD, respectively. This new approach enables tracking and solving movement and interactions of individual droplets. User-defined models were created to take coalescence and reaction kinetics into account. Coalescence created larger droplets, while the reactions decreased droplet size and increased its density. Drag caused funnelling effect, which pulled droplets towards the centre line of the descending cluster. This research is the only study known by the present authors in modelling liquid-liquid systems with the CFD-DEM coupling. Simulating coalescence and chemical reactions for discrete droplets enables more realistic simulations. However, CFD- DEM simulations are computationally resource intensive already without additional models, so a full scale industrial settler modelling still waits for further increase in computer performance. INTRODUCTION Flash smelting is a method used in copper and nickel production. In the flash smelting process, oxidation of sulphides in a concentrate is used to release energy needed to smelt the feed. In the process, copper matte is formed. Matte has copper content in the range of 55 – 70% (Sridhar, Toguri, & Simeonov, 1997), the rest is mainly sulphur and iron but has still many other impurities (Taskinen, Seppälä, Laulumaa, & Poijärvi, 2001). Oxidized iron forms iron-silicate slag while SO2 is collected for acid production (Davenport & Partelpoeg, 2015). The Outotec flash smelting furnace (FSF) can be divided in four major component: concentrate burner, reaction shaft, settler and uptake. Concentrate, flux and oxygen enriched air are injected into the reactor through the concentrate burner. The mixture then reacts in the reaction shaft forming matte and slag, which are collected in the settler, while off-gases flow out of the reactor through uptake for heat and dust recovery, and SO2 collection for H2SO4 production. The matte and slag form separate layers due to immiscibility and density difference. Raw material feed is continuous, but the matte and the slag are tapped periodically. A flash smelting furnace is depicted in Figure 1.

Jan 1, 2019

By H. S. Wilson

"The property owned by the Lamaque Mining Company comprises a group of forty-four claims and fractions occupying an area of about 2,458 acres, in west-central Bourlamaque township, Abitibi county, Quebec. It is on ,the outskirts of the towns of Bourlamaque and Val d'Or, about 70 miles east of Noranda, near the eastern end of the belt of greenstones of Keewatin and Timiskaming age that extends eastward through Kirkland Lake into northwestern Quebec, terminating in Haig and Jurie townships 40 miles to the east.The claims on which the orebodies occur were first staked in 1923; No. 3 vein was discovered the following year. The original discovery was made by R. Clark in 1923. This was a small quartz vein containing a pocket of coarse gold on the north side of a hill near the northwestern corner of block 3. It is said that all the gold was removed in one shot in blasting into the vein; elsewhere it was barren. A picket line was then run west along the strike of the vein, which occupied a narrow shear zone, and about 2,000 feet west, in prospecting on either side of the picket line, a large boulder of quartz and tourmaline containing visible gold was found. This led to more intensive prospecting by trenching in the vicinity with the result that the No. 3, or 'float' vein, about 250 feet north of the boulder, was found. Due to low ground this vein was exposed in only one trench. The only other important vein found on the surface was the No. 1, or H, vein, which was exposed in several places by stripping and trenching, but it did not carry appreciable amounts of gold."

Jan 1, 1954