Search Documents

By Ruschitzka C

The productivity and economic success of a German hard coal mine is attributed to the high productivity of a small number of operation points; however high rates of production are associated with increased gas emission at the working sites. Therefore modem high technology is required in order to reach the planned production rate, since high methane concentrations often cause unplanned breakdowns in operation. The optimised simulation of gas emission is a fundamental planning tool for mine design as well as for determining the potential of a coal deposit and has increased in significance over the last years. Methane-INFO enables the three-dimensional, graphical simulation of a working site taking account of different aspects such as the mine design, ventilation, production rate, geology, seam quality, gas exhaustion, etc. The following paper gives a short overview over the benefits of the discussed system.

Jan 1, 1995

By M Wen, J Gerit, C A. Pelletier, D Muggli

On-land waste rock dumps at BHP Billiton Base MetalsÆ Island Copper Mine (ICM) near the northern end of Vancouver Island, B.C. continue to discharge ARD. These waters, which amount to approximately five million cubic metres each year, are injected into a three-layer, meromictic pit lake for treatment. The top layer is brackish water, replenished by each yearÆs rainfall (amounting to nearly 2 m/year). This top layer of water must meet effluent permit limits for heavy metals. This water eventually exfiltrates through a æbeachÆ waste rock dump, which is 93 per cent submerged along the north shore of Rupert Inlet. The middle and bottom layers of the Pit Lake are saline and currently oxic (2 mg/L dissolved oxygen) and anoxic (0.03 mg/L dissolved oxygen), respectively. Spreading of a liquid fertilizer every ten days throughout the top layer results in plankton and bacterial blooms that scavenge zinc, copper and cadmium out of this layer eventually to become mineral sediment in the bottom of the pit lake. Adsorption on planktonic skeletons and mineral precipitates also scavenges these dissolved metals from the middle and bottom layers to form bottom sediment. Sulfate reduction has recently begun in the bottom sediments. Diagenetic processes in the bottom sediments will eventually transform most of the dissolved heavy metals into insoluble sulfides. Cycling of ferric iron between the sediment and the water column and back seems to contribute dramatically to the biogeochemical metal removal processes. This biogeochemical system serves to maintain the top-layer water well within permit limits for discharge to the environment.

Jan 1, 2003

IT is very difficult for a founder engaged in jobbing work, comprising all sizes and classes of castings, to appreciate that the analysis of the iron he is using cannot entirely fill the situation he desires for his varied classes of work. Neither is there any panacea in the shape of an iron mixture that will suit the whole of his floor for the day.From his own experience he generally alters his cupola charges during the cast, endeavouring to meet at the same time the requisite metal composition for the castings he is about to pour.The founder on repetition work is in a much better position to stabilise his methods, arrive at a certain pig-iron' analysis, regulate...

Jan 1, 1926

By Amusin BZ

The concept of rigid or yielding bolts is discussed based upon support requirements for excavations of equivalent geomechanical behaviour. The concept of equivalent geomechanical behaviour is introduced for comparison purpose where the rock mass properties are varied for a given depth (stress) so that the deformation of the roof without any support remains constant = 300mm. A simple experimental theoretical analysis for a uniform stress field acting on an axi-symmetric excavation is conducted to establish roof bolt requirements under different conditions such as width of a given excavation, time of setting of support etc. Results are presented in graphical forms.

Jan 1, 1992

By B Roache

Ground support installation into the face of development headings has become an accepted practice at many Australian hard rock mines. Ground support is installed in the development face to reduce personnel exposure to rockfall while conducting work tasks such as marking up, installing lifter tubes, charging, and face sampling. The ground support system installed in the face is typically friction bolts and mesh. This support system can be effective at reducing rockfall occurrence, but it also increases the cost of development per metre, in terms of capital for the ground support, jumbo and operator capital allocation and the installation time slowing each drill and blast cycle. Other issues associated with meshing and bolting the development face include management of rock bolts and mesh sheets in the fired dirt of every cut, damage to services such as vent duct, geometry issues when installing ground support onto irregular development profiles and operator error. Fibrecrete installation onto the development face for support is an option considered by many mines, but it can be difficult to manage due to the removal of visual indications of misfires and slowing the mining cycle due to the wait time for fibrecrete curing. The use of Thin Spray Liner (TSL) products in underground hard rock mines has been relatively infrequent in the past, mainly due to issues with cost, health and safety, and liner strength. Kanmantoo Mine investigated the use of TSLs for the purpose of development face support, while collecting data on the costs and practicalities associated with their use. Several TSL products were trialled and a preferred TSL product was selected for use as face support. Cost savings, drill and blast cycle timing improvements and other benefits were achieved while meeting the requirement to reduce rockfall risk.

Mar 29, 2023

By Mathew P. J

The CSIRO Division of Mineral and Process Engineering in Melbourne has been developing on-stream analysis sensors based on neutron and gamma radiation for better control of quality and process operations. This has resulted in the development of Ironscan, an on-stream analyser that measures the iron content of both lump and fine iron ore on conveyor belts. It can be mounted under existing conveyors with minimal modifications to the conveyor structure and can cope with steel cables in the belt. An interface gauge and an on-stream coal ash analyser have also been developed, both based on measurement of natural radioactivity. The interface gauge monitors the interface between liquor and mud in thickeners and washers, provided the natural radioactivity of the mud is sufficiently high to detect it above background. The natural-gamma ash gauge is a valuable addition to the Coalscan range of ash gauges. It is applicable to heavily laden coal conveyors or bins where the coal bed thickness exceeds 30 cm, and also to lightly laden conveyors, provided the coal is profiled on the conveyor.

Jan 1, 1991

By T M. Nester, D J. Reardon, A N. Page, B J. Barsanti

The load capacity of a friction bolt has long been regarded as 4 t/m of embedment for ground support design analysis and supported by in situ pull test results. In recent years, the authors have observed lower pull test results or inconsistent results which were rarely sighted in the early 2000s. The lower pull test results indicated in some cases that reliable friction bolt capacity (≥90 per cent of results) is closer to 3 t/m of embedment with some geotechnical engineers adjusting the ground support parameters in the design work accordingly. This can be in contrast with other mines which reliably obtain 4 t/m (or greater) using the same suppliers bolt in similar ground conditions. This raised several questions: • What is the effect of poor installation (bolt twist or bolt hole deviation)? • Does the performance of friction bolts vary in different rock masses? • Does bolt performance vary between suppliers? • What effect does increased jumbo feed/percussion/rotation settings have? • Have the bolt dimensions or steel strip width changed? • Have the physical bolt properties changed? • Have the steel properties changed? This paper was aimed to answer as many of these questions as possible and discuss each variable in detail. This project included friction bolt trials at various mine sites across Australia, multiple friction bolt manufacturers, steel manufacturers and laboratory analysis. The paper also includes discussion on what the authors consider best practice for pull testing. It should be noted, the terms ‘friction stabiliser’ and ‘split set’ used in this paper are used in a generic manner and is not linked to any specific ground support supplier. Whilst its acknowledged within the industry the term split set and friction stabiliser is used interchangeably, the authors acknowledge that the term split set is a trademark of Split Set Mining Systems and has been used in context in this paper.

Nov 29, 2022

By Van Heuzen JA

The extensive deposits of brown coal in the Latrobe Valley form the major solid fuel resource in Victoria and are the energy source for most of the State's power generation. This paper describes the coalfield resources allocated for electricity generation and a potential sequential develop- ment of these areas in future years to supply future power stations.

Jan 1, 1982

By N Setoudeh, A Nosrati, N J. Welham

The current surge of interest in lithium (Li) is due to the anticipated demand for electric vehicles and small scale power storage. Brine deposits contain most of the global Li resource, however hard rock deposits can be more readily and rapidly developed and comprise the majority of proposed projects. These projects plan to use the conventional processing routes of dense medium separation and / or flotation to produce a spodumene concentrate for sale. The standard route for subsequent processing of spodumene concentrate is thermal decrepitation, acid leaching, solution purification and precipitation of lithium carbonate. This is typically followed by further purification. A number of projects have ores which contain other lithium minerals, principally micas, lepidolite and zinnwaldite, necessitating an alternative treatment route. Several different routes for spodumene processing are under development to reduce costs to compete with brine projects. This paper will give an overview of the strengths and weaknesses of the current and alternative processes.CITATION:Welham, N J, Nosrati, A and Setoudeh, N, 2017. Lithium ore processing – an overview of the current and new processes, in Proceedings MetPlant 2017, pp 185–194 (The Australasian Institute of Mining and Metallurgy: Melbourne).

Sep 11, 2017

An on-stream iron ore analyser has been developed in collaborationwith Hamersley Iron Pty. Limited for determining the iron content ofboth lump (- 30+ 6 mm particle size) and fines ( - 6 mm particle size)on conveyor belts. The analyser, which is called IRONSCAN, is basedon pair production, and is now commercially available from Mineral ControllnstrumentationLimited (MC!) in Adelaide. It can be mounted underexisting conveyor belts with minimal modifications to the conveyor structure,and the presence of steel cables in the belt does not interfere oncethe analyser has been correctly calibrated. The analyser has been extensivelytested on both lump and fines on the shiploading conveyor at Dampier,and typically the root mean square (Lm.s.) deviation between singleIRONSCAN measurements and conventional chemical analyses is betterthan 0.5070 Fe. It is currently being evaluated on - 150 mm ore from theprimary crusher at Mount Tom Price, and initial result are encouraging.The principal advantage of IRONSCAN is that it provides rapid informationon ore grades. But perhaps its greatest potential is at the primarycrusher where conventional sampling and analysis is very expensive toimplement.

Jan 1, 1988

This paper explores options worthy of consideration in the management of S02 produced from the gold roasting operations at Kalgoorlie. Some of the options have relevance to other sources of SO2 in the region, eminating from nickel smelting operations. The paper considers the following options: 1. Capture of SO2 within the roaster where sulphur-containing reaction products are mixed with the calcine. 2. Processes in which the sulphur-containing products are bled separately from the stack for further treatment or for dumping as a waste. These include: Seawater-based scrubbing of SO2; Sulphuric acid manufacture as a feedstock for fertiliser production or for leaching of bauxite; its use as Caro's acid: and the production of value-added sulphur-containing reagents eg liquid S02 and sulphonic acid.

Jan 1, 1992

By Moore A. J

This paper describes the use of a wavefront reinforcement model which has been developed to supplement established charge mass scaling methods. The model allows for the time taken for blast vibration wavefronts to travel from each blasthole, and has been successfully used to explain the reason for directional increases in both air and ground vibration in certain situations. The model has been used to identify wavefront reinforcement due to the propagation of air vibration and ground vibrations in certain situations. The paper includes a throw (or cast) blasting case history which provides multi-station evidence of the strong directional nature of wavefront reinforcement.

Jan 1, 1995

By Mosusu N

Geothermal anomalies of different types occur within distinct geological/structural settings in Papua New Guinea. According to R.F. Herring, geothermal occurrences in Papua New Guinea can be classified into two types, those related to vulcanism (Lihir, Rabaul and other series of islands along the volcanic arc) and those resulting from a regional heat flow probably caused by radiogenic sources, for instance those in the Wau/Bulolo area. The manifestation of this potential source of energy generally coincides with either converging or diverging tectonic plate boundaries. Previous inventories on thermal waters were carried out by vulcanologists from the Rabaul Observatory in the early 1960s. However, these studies rarely included chemical analyses of water and gas emissions and the investigations were carried out in an ad hoc manner, generally as a secondary activity. The most recent investigation on thermal waters was conducted on Lihir Island in connection with the development of the open pit gold mine. These studies included detailed exploratory drilling to a maximum depth of 730 m, and a water chemistry isotopic sampling and analysis programme. The hydrothermal waters were not considered as an energy source but as a hazard during the development stage of the mine. Nevertheless, the geothermal anomaly observed at Lihir includes hot springs emerging along the coastal zones with temperatures that approach 100¦C, steam, and thermal borehole waters with temperatures that exceed 200¦C. Chemical analysis results of thermal fluids from Rabaul, Talasea and other areas in Papua New Guinea generally show high total dissolved solids and low pH. In contrast, recent results from the deepest and hottest thermal source at Lihir shows a neutral pH, a Na-CI-SO4 composition and temperatures above 200¦C. Despite the concentration of chloride being similar to that of sea water, other chemical results and stable hydrogen and oxygen isotopic compositions of thermal fluids imply the source to be mixture of local meteoric water and deep thermal water rather than sea water. Results of geothermal modelling suggests that the total geothermal uptlow is equivalent to 54 MW.

Jan 1, 1997

By O Dominguez

Mine value chain reconciliation (MVC) is a necessary procedure to evaluate a mine’s performance against the assumptions and models used to plan mining and processing operations. Using nomenclature from Parker (2012), F2 reconciliation is the ratio between material received at the mill, compared with material sent to the mill, commonly reported in terms of tonnes, grade and metal. Measurements of material sent to the mill can be estimated in many ways, including: fleet management system (FMS) records, truck counts, or volume reduction. Most time-based reconciliations (for example, month-end reconciliation) use short-term model depletions of in situ rock measured by periodic topographic scans or surveys.

Mar 22, 2022

With mining development on hold and other underground works in a slowdown, the develop- ment of nuclear waste repositories takes center stage on the American rock engineering scene. Three repositories for commercial spent fuel -- in salt, tuff, and basalt -- are in the phase of site characterization and conceptual design, and one pilot project for defense high-level waste in salt is under construction. A repository design for crystal line rock has recently been postponed. Because of strict quality assurance requirements throughout design and construc- tion, and because of the need to predict and ascertain in advance the satisfactory perfor- mance of the underground openings, much intellectual energy has been expended to analyze underground openings in the unusual circumstances of the repository environment. In the long term, these efforts will lead to an improved understanding of rock behavior and improved methods of underground analysis and design. For the shorter term, a formalized ground control plan was developed, the princi- ples of which may be applied to other types of projects. This paper summarizes the status of underground design and construction for nuclear waste repositories and presents some details of the ground control plan and its individual elements.

Jan 1, 1987

By Myers I. A, Peters S. G, Bultitude R. J, Dowling K

Gold-quartz and antimony-gold-quartz veins in the Hodgkinson Province are hosted by subgreenschist to greenschist facies metasediments and show no spatial association with granitic rocks. They commonly parallel axial plane foliations or occur in brittle to brittle-ductile shear zones. Detailed mapping in the Hodgkinson goldfield indicates that vein systems are isolated in distinct structural and lithologic domains by post-mineralization faulting. Gold-quartz and antimony-gold-quartz veins have distinctive mesoscopic textures characteristic of the mesothermal vein environment. Some of the antimony-gold-quartz veins are located on domain boundaries which truncate the gold mineralization. In. some areas, tin and tungsten-tin mineralization which are spatially related to Late Palaeozoic granitoids appear to postdate the gold-quartz and antimony-gold-quartz mineralization.Oxygen and hydrogen isotopic studies of vein and alteration assemblages associated with these diverse ores provide constraints on fluid sources and have implications for the origin of mesothermal gold mineralization. The available isotopic data are consistent with a dominantly magmatic source for tin and tungsten-tin mineralization although there is evidence of a late-stage meteoric component in some tin-mineralizing systems. Although a distal magmatic contribution cannot be entirely discounted, the gold-quartz and antimony-gold-quartz veins were probably deposited from deeply

Jan 1, 1990

By Garland W

Access to geoscience reference informa- tion including mining and mineral processing has increased considerably in the last five years in Australia. This has been due principally to the use of computer-based information storage and retrieval systems. The main reference data base for the mineral and petroleum industries and disciplines in Australia is the Australian Earth Sciences Information System (AESIS), cooperatively developed and coordinated by the Australian Mineral Foundation (AMF). AESIS is created on the CSIRO computing network (CSIRONET) which has a CYBER 76 host computer located at the CSIRO Division of Computing Research (DCR) at Canberra. Data entry was until recently carried out by AMF using a dedicated line through the Adelaide CSIRONET node to the CYBER 76 interactive system. Data entry is now done directly at the AMF on a DEC PDP 11/44 mini computer that is also a host work station on CSIRONET. Data collection via magnetic tape media input from other computer-based systems is under development. The software used for data entry and management of the data base was developed by CSIRO CILES Systems Development Group. For public interactive online use the AESIS data base is transferred by tape to AUSINET - the Australian information net- work run by ACI Computer Services, Melbourne, where the data base is converted to a form suitable for the IBM STAIRS software. CSIRO facilities at DCR Canberra are used to produce computer type-set camera ready products and output in microform, on magnetic tape or as graphic display. Keywords: Earth sciences information, Computer applications, Information storage and retrieval, AESIS, Data bases, Australia.

Jan 1, 1983

By D R. Andrew, K T. Morrison, J F. Tiedgen

Waste blasting in iron ore operations can pose a number of technical challenges, including blasting through variable geology and blasting soft ground in wet conditions. Blast patterns are designed to be loaded with a specific range of explosives with unique characteristics and properties. Each explosive product will produce an optimal blast outcome for a given set of blast parameters and ground conditions. Sites characterised by softer rock typically require low-density, low-energy explosives. Historically, these products have contained a high ratio of porous ammonium nitrate prill and are only suitable for dry blastholes. When blastholes within a pattern are found to be unsuitable for such explosives due to wet, damp or muddy blasthole conditions, a new product is selected. While it is easy to switch products to match blasthole conditions, the different properties of the new non-ideal product can impact blast performance and increase loading times and costs.Flexigel™ is a solids-sensitised emulsion blend suitable for loading at variable densities and energies in dry, damp, muddy or wet blastholes. It is a universal product that can be loaded to match ground and blasthole conditions or complement other explosive products.At Fortescue Metals Group’s Cloudbreak site, Flexigel™ was trialled through a series of matched pair blasts in order to optimise blast outcomes in conditions that were non-ideal for existing explosive products and to reduce the overall cost of drill and blast operations. Flexigel™ yielded improved instantaneous dig rates and improved loading efficiency when compared to a traditional emulsion blend. The results also indicated that variable-density and variable-energy products afford greater flexibility for optimising blast outcomes across all ground and blasthole conditions trialled.Trials of Flexigel™ at Cloudbreak have shown that a variable-density solution is available for conditions where traditional explosive products are non-ideal. As such, Flexigel™ is able to fill a major void at any operation where the desired low-density, low-energy explosive product must be substituted for a more expensive traditional emulsion blend or heavy ammonium nitrate/fuel oil.CITATION:Andrew, D R, Morrison, K T and Tiedgen, J F, 2015. Flexigel™ – a variable-density solution, in Proceedings Iron Ore 2015, pp 413–418 (The Australasian Institute of Mining and Metallurgy: Melbourne).

Jul 13, 2015

The design of mine ventilation systems for the BHP Steel Division Collieries is based on the acquisition of ventilation survey data for the establishment of a realistic computer net- work model. The branches which form the net- work for the computer models are calculated from a range of resistance factors incorporat- ing both a frictional and shock loss component. Since shock losses can account for up to 30 per cent of the total energy losses in mine airways the use of friction factors alone without accounting for shock losses will result in the choosing of an insufficiently performing fan. Published tables of friction factors have in- variably been taken from metalliferous or single entry studies and consequently are not reliable for Australia's mining conditions where multiple entries with regularly spaced cut-throughs are the normal practice. Typical resistance factors for roadways of rectangular cross-section 5.5 m x 2.0 m, with coal sides, have been found to vary from 0.11 Ns2/m8/km where no timber supports are used, to 0.98 Ns2/m8/km where double centre legging together with wooden chocks is used. In addition to the range of resistance factors due to varying support methods, the nature of use for a roadway is very significant because of the condition of repair and upkeep maintained.

Jan 1, 1983

The Canada Centre for Mineral and Energy Technology (CANMET) /Calgary Coal Research Laboratory and the National Research Council in Ottawa established a joint working research group with industry to develop and test various computer models for application in surface coal mining operations in western Canada.The first part of the paper deals with the problems the group experienced during the past two years especially having model specification and requirements defined and understand site management practices.The second part of the paper deals with site specific development of general mine model for TransAlta Utilities' Highvale Mine in Alberta. Described here are the development of an interactive truck/shovel model for their three pit operation, selection and application of dragline model for tandem operation with the extended bench method, criteria for operational model of the five seams operation with selec-tive mining approach.

Jan 1, 1985