Search Documents

By K L. Avarmaa, M A. Rhamdhani, A D. P Putera, H T. B M Petrus, G A. Brooks

Multistage slag treatment was carried out to investigate boron removal from metallurgical grade silicon. Boron is known to be one of the most difficult elements to remove from silicon. Depending on boron initial concentration, boron can be removed from silicon into certain level; most previous studies have attained final 50–100 ppmw (parts per million weight) boron in the silicon using slag treatment. The term ‘multistage’ refers to a process where the resulting silicon from the initial slag treatment is further refined multiple times using a new slag. In this study, an initial slag composition of 45CaO-45SiO2-10Al2O3 (wt per cent) was utilised. Using this technique, boron level in the silicon was expected to be gradually lowered because the new slag will always have more capacity to reach the equilibrium distribution coefficient (LB = (ppmwB)slag/(ppmwB)Si). The current study was carried out through combined thermodynamic calculations (using FactSage™ ver 8.2, by Thermfact Ltd, thermochemical package) and high-temperature experimentation. The thermodynamic calculations were carried out for reactions at 1500, 1550, and 1600°C for three different scenarios: 1. Single stage refining with varied slag to Si ratio. 2. Multistage refining with slag to Si ratio of 1:1. 3. Multistage refining with slag to Si ratio of 2:1. The multistage experimental work was carried out at 1550°C under inert gas atmosphere each time for 2 hrs, with slag to Si ratio of 2:1. The simulation results indicate that the boron distribution coefficient stay essentially constant with varying slag to Si ratio and temperature, around 1.8 to 2, and the experimental results measured LB in the same range, between 1.5 and 2.5. By harnessing this feature, the simulation showed that boron can be removed by approximately 78 per cent in each stage. The experimental result confirmed that the boron concentration in the silicon was reduced by a total of 97.8 per cent from its initial value using four stages of slag treatment, from initial 270 ppmw down to 6 ppmw.

Aug 21, 2024

By Muller GP, van Deventer JSJ

A mineralogical analysis has shown that in the Hartebeesfontein ore studied, uranium is associated mainly with uraninite, sulphides such as pyrite and to a lesser degree carbonaceous material such as thucolite. Little could be learned from the literature regarding the mechanism of flotation of these uranium-bearing minerals. A wide variety of reagents were used so that conditions enhancing the flotation of either the sulphides, carbonaceous material, oxides like uraninite, or combinations thereof, were created. As could be expected, the xanthate based floats gave-better selective recovery of sulphides than oleic acid. A substantial fraction of the uranium is associated with pyrite, so that addition of oleic acid to a xanthate float did not enhance the recovery or grade of uranium. After a pre-leach with sulphuric acid in which the pH and Eh were controlled so as to destroy the uraninite, higher uranium recoveries were obtained for the combined float (xanthate, DTP and oleic) and the DTP float. This was most evident when iron was added before flotation. Roasting, which destroyed the sulphides and thucolite, caused a significant decrease in uranium recoveries. The uranium liberated in this way was obviously not flotable in the same way as the uranium liberated from uraninite. A small amount of iron (2 kg/t) added before milling resulted in slightly higher grades and recoveries of sulphur for xanthate based floats. Higher iron additions had a detrimental effect on sulphur recoveries. Even in the case of oleic acid the addition of small amounts of iron had a positive effect on the recovery of sulphur and uranium.

Jan 1, 1993

By Rabie A. S, Fouad K. M, Ammar A. A

The existence of Gabal El Kahfa ring complex, located in the Eastern Desert of Egypt, has been ascertained from aeromagnetic and aeroradiometric survey data as well as by aerial photography. Two maps for -the net aerial radiometric measurements reduced to ground level and aerial magnetic data corrected for the regional normal gradient of the earth's magnetic field have been constructed. The aeroradioactivity data have been interpreted geologically and analyzed statistically to outline various radiometric units and compute their charac- teristic statistics. The ring complex showed a circular radiometric feature and yielded a radiometric mean background and a standard deviation of 6.48 and 0.89 pR/h respectively. Besides, the observations showed a normal distribution. The aeromagnetic data have been reduced to the north magnetic pole, then filtered to produce the regional-and residual-component maps. Statistical trend analysis was conducted for the tectonic linea- ments resulting from the three magnetic maps, to define the structural framework of the area under study. This statistical study proved the exis- tence of trends in the east-west, northwest-south- east, northeast-southwest and north-south directions. The ring complex is characterized by a circular magnetic feature, whose average relief is 2150 nT. It is included within a high east-west trending magnetic zone. The latter represents a deep-seated uplift or anticline which is bordered from all sides by some faults of different trends.

Jan 1, 1988

By Thirumalai K, Peluso R. G

The United States has more than 45 billion tons of economic coal reserves in seams above 10 feet thick and current underground production from thick seams represent less than three per cent of the total production. A tripling of underground production from thick seams is necessary within the next 10 years to meet U.S. coal production demands. An analysis of underground accident and production data is presented in the paper. A study of accident and injury distribution in different coal seam heights in the eastern and western part of the United States in seams ranging in thicknesses from 5 to 15 feet indicates that the seam thicknesses do not produce adverse impact on underground injury incidence. Accidents associated with roof falls and haulage account for about 70 per cent of underground mining injuries.

Jan 1, 1976

There exist many formulae for designing coal pillars. However, when applied to a given set of mining parameters, they lead to different pillar sizes and factors of safety. From the subsidence point of view, the pillars designed as protection pillars not only have to be stable, but also have to limit subsidence over them to a level acceptable to the structure being protected. The subsidence over a pillar of given width to height ratio depends upon the mining depth. A pillar may be stable, but the subsidence over it may be quite large and unacceptable for the structure. In many cases even though pillars may yield, they support the undermined strata and reduce surface subsidence. In addition, the yielding pillars eliminate peaks and troughs in the surface subsidence profile and reduce ground strains. In a given situation, whether a pillar yields or not depends primarily upon its width in relation to mining depth.

Jan 1, 1992

By C M. Stewart, P Bowen

McArthur River Mine, in the Gulf Country of the Northern Territory, exploits one of worldÆs largest deposits of zinc, lead and silver. It was officially opened in September 1995, 40 years after its discovery in 1955. This paper describes the geological, engineering and metallurgical assessments which made up the feasibility study. It then relates how these study components compare with the first two years of operation. The challenges that had to be overcome before the McArthur River Mine became economically viable included the metallurgical problems associated with extremely fine grained ore and the development of an effective mining process.

Jan 1, 1998

By Donald D

A number of standard tests are conventionally carried out to characterise strength properties of rock. The values of the parameters obtained are often affected by planes of weakness or defects in rock structure. For the purpose of mine design, the range in values or the class of the strength (obtained from a number of tests) is generally more important than a precise value (obtained from a single or limited number of tests). Research has been conducted to establish a relationship between an indentation index and the strength of the intact rock material from the Eastern Goldfields of Western Australia. The Tamrock Raise Boring Index (RB-i) test, which is quick and easy to perform, was selected as the indentation test. The results show that, for heterogeneous, strong to very strong rock, there is a good correlation between the indentation index and the uniaxial compressive strength and tensile strength.

Jan 1, 1996

By Chend J

Research conducted into backfill drainage at Mount Isa Mines since 1992 is described. Piping in draining backfilled scopes has been the primary cause of bulkhead failures and emphasis is placed on research into the piping mechanism. Laboratory and in situ tests aimed at understanding the piping mechanism have been conducted and the results are presented. A case history of piping in a draining bench scope fill mass is described and a technique for reducing the potential for bulkhead failures in hench stopes is presented. Hydraulic fill is produced by standard cycloning of tailings and the overflow (reject material) is sent to thickeners prior to placement in the tailings dams. Research into the partial introduction of thickener underflow into the backfill system and its influence on backfill drainage is also descrihed.

Jan 1, 1998

Using Dynamic Simulation Throughout a Process Plant's Life Cycle

Sep 13, 2010

Traditional vat leaching has been done on a batch basis, which involves loading the vats, leaching, drainage, washing, draining again, and unloading. As a result of these many steps and the attendent cost of labor, vat leaching is generally not an economic proposition. Also, like heap leaching, there is a tendency for channeling to occur within the bed, whether the leach solution flow is by percolation upwards or downwards. No doubt experimenters over the decades have been enticed by the idea of fluidization induced by upward flow through the ore bed. If the bed could be fluidized, then a continuous flow of material could be set up, dispensing with the high cost of loading and unloading the vat. A quick calculation of solution flow requirements, however, soon reveals that the volume of constant liquid movement necessary to sustain fluidization is prohibitive from a power and cost standpoint. The premise of the Mackie Vat Leaching Jig (MVLT) concept was that the large volume of liquid flow required for fluidization could be achieved instantaneously, and that during this small element of time, the solids would flow under the influence of the hydraulic gradient in the vat. If this procedure could be repeated in a cyclic manner, then a steady-state condition could be set up. Experiments in the laboratory demonstrated that solids flow could be achieved in this manner.

Jan 1, 1991

In order to understand the technique, basic theoretical principles of radiation emission and in- strumentation theory are reviewed. Methods of surveying, reduction of data and interpretation are outlined. Other applications of the technique (e.g. in airborne geological mapping), as well as its specific use in uranium exploration, are discussed. By means of case history-type examples the successful applicant of gamma-ray spectrometry, as a tool in Australian mineral search, is demonstrated.

Jan 1, 1969

By A J. Morrison, M Yahyaei, J S. Siong, J Wang, K Runge

The flotation cells used to upgrade ultrafine metallurgical coal (-250 µm) are usually poorly controlled leading to unnecessary loss of combustibles from the flotation system. This is mainly because coal flotation cells are typically controlled for process stability rather than optimisation of flotation performance. This is especially true for a flotation device commonly used in coal applications in Australia – the Jameson Cell. This then provides an opportunity to improve the flotation performance by shifting from a stabilising control strategy to a proactive optimising control strategy. For an optimising control strategy, the control system will require a means of relating and then measuring in real-time, the effect of changing operating conditions on the coal flotation performance. Hence, the major aim of this work is to propose a possible model-informed process control strategy that could be used for real-time performance optimisation. In this study, industrial site work was conducted on an industrial-scaled Jameson Cell at a Coal Handling and Preparation Plant (CHPP) in Central Queensland, Australia where superficial gas velocity was controlled to six different levels. At the same time, other process variables such as froth depth and flotation feed properties were measured. The empirical models developed from this study suggested that combustible recovery is a function of superficial gas velocity, froth depth, feed solid content and feed ash content and that a peak in combustible recovery existed as a function of superficial gas velocity. This led to the development of a model-informed control strategy that aimed to maximise the combustible recovery by determining and then operating the cell at the superficial gas velocity at which the peak occurs. This peak superficial gas velocity was found to be only a function of feed solid content. Based on these findings it would seem possible to operate a Jameson cell at peak performance by online measurement of feed solid content, prediction of the optimum superficial gas velocity and stabilising control to maintain operation at that superficial gas velocity set point. The development of this modelinformed control strategy can serve as a basis for the development of a more sophisticated modelpredictive control (MPC) system. However, more work will need to be done to improve the predictivity of the combustible recovery model by measuring and modelling performance over a wider range of operating conditions.

Aug 24, 2022

By Sen A. K

The Chiria Iron Ore deposit falls within the well-known Horse-shoe-shaped Singhbhum-Bonai-Keonjhar belt in India, where most of the deposits supplying ore to various steel works of Steel Authority of India Limited (SAIL) and Tata Iron and Steel Company (TISCO) are located. With an estimated reserve of about 2000 million tonnes of ore (at 55 per cent Fe cut-off) spread over four contiguous blocks, it is the largest iron ore deposit in India and one of the largest in world. The present study is confined to only one of the four blocks of Chiria viz North Block, comprising an area of 2.11 km2. `Corporate Plan 2005' of SAIL envisages development of a large open cast mine at Chiria to meet its enhanced requirement of iron ore by 2001-02 AD.

Jan 1, 1995

The Kunwarara magnesite deposit is the largest known magnesite (MgCO3) deposit in Australia. It is located under black soil plains to the north of Rockhampton in Queensland. The deposit consists of magnesite nodules set in a fine-grained sandstone, siltstone and mudstone matrix. The magnesite is derived from weathering of serpentinite in adjacent hills and transport of magnesium in solution to a Tertiary/Quaternary river system. The magnesium has come out of solution in the active river system, and combined with atmospheric and biogenic CO2 to form magnesite nodules. The magnesite can be very pure with certain varieties up to 98 per cent MgO (LOI free). The deposit has been mined since 1991 and processed into magnesia (MgO) which is sold into refractory, agricultural and other markets. The geologist is an integral part of the small mine technical team. The role of the geologist includes characterisation of the ore through drilling and bulk sampling, supervision of geological aspects of mining and assistance in the optimisation of ore processing.

Jan 1, 2000

By Burgess JM

Research on gas distribution in the iron- making blast furnace has been conducted in three separate areas. Firstly, experimental work has been conducted to determine the important parameters which dictate the pressure losses in homogeneous and heterogen- eous packed beds. Secondly, a theoretical analysis of gas flow through the furnace softening-melting zone has been undertaken to determine the effect of the shape of the zone on the distribution of gas flow towards the furnace walls. Thirdly, a theoretical programme has been undertaken to develop methods for the prediction of furnace soften- ing-melting zone shape from furnace tempera- ture and gas composition measurements.

Jan 1, 1980

By Clements R. J, Davey J. M

Development of the process from the pilot stage to the current operation of the Capel, W.A. plant is briefly described. The design criteria for a larger sized plant are discussed together with factors that relate suitable feedstocks and coal types to the capital cost, capacity and product grade of future plants at locations other than Capel. The application of the process to the direct reduction of iron ores is briefly discussed including its commercial application at Rockwood, Tennessee.

Jan 1, 1979

The need to schedule ore production to make maximum use of the strength gained by cem- ented fill during curing is discussed, to show how cement content and hence fill cost can be kept down for any particular operation. Results from laboratory testwork on Isa Mine fill conducted by the author while employed by Mount Isa Mines Limited form the basis of the Discussion

Jan 1, 1973

By Doyle P, Mulroney D

The Cassidy Shaft was sunk to access the Mount Charlotte and Reward Orebodies below the Flanagan Fault. The 1,184m deep shaft is concrete lined to 6.5m diameter for its full depth. The initial 590m was excavated by stripping into a 1.8m diameter borehole and hoisting the broken material through the existing mine. The remaining 594m was excavated by conventional shaft sinking methods. The shaft was sunk through 3 existing plats and an additional 8 plats cut. 1,800 tonnes of steel and 8 cables were installed during the furnishing of the 4 compartments.

Jan 1, 1985

HISTORIC SIGNIFICANCE OF EXPLOSIVES TO MINERAL PRODUCTION The ancient method of breaking rock was to build a wood fire against the face, heat the rock through and then pour water on the heated ore-bearing rock to cause it to break by tension. It was too slow and costly as the forests around the mines were cleared and transport of wood became difficult. Black powder had been used for 300 years as a gun propel- lant. ('Black' after Berthold Schwartz, a German monk, Figure 1, and the inventor of the gun who was given the epitaph `Here lies Berthold the Black, the most abominable of inhumans who by his invention has brought misery to the rest of humanity'). Only at the beginning of the 17th Century, black powder was introduced for loosening rock in European mines. In 1802 Dupont started black powder manufacture on the Brandywine Creek. The ignition train of powder was enclosed in goose quills, straws, rushes, paper or wooden tubes. The time interval between igni- tion and blast was pure speculation.

Jan 1, 1988

By Wright G. A

The objective of refining in steelmaking is to reduce the concentration of impurity atoms, e.g. sulphur, phosphorus, from an initially high level to a specified low concentration. A two-film theory of refining is presented in which the rate of

Jan 1, 1980