Search Documents

By Shun Myung Shin, Dong Hyo Yang

Cobalt is recovered from square type of spent lithium ion batteries (LIBs) containing 5~20 % Co, 5~7 % Li, 5~10 % Ni, 15% organic chemicals, and 7% plastics together with Cu, Al, Fe, and Mn. The waste LIB was prepared by physical treatment. After screening, the crushed LIBs were separated to +8 mesh, -8/+16 mesh, and -16 mesh powder. Among these, -16 mesh powder was selected for leaching. The leaching test was investigated at 2 M H2SO4, 6 vol.% H2O2, reaction temperature 60 ?, agitation speed 300 rpm, solid/liquid ratio 50 g/ 500 ml, reaction time 1 h. The leaching efficiency of cobalt was more than 99 % and its concentration was 24.9 g/L. For removing of impurities such as copper, iron, and aluminum in the leaching solution before cobalt solvent extraction, the impurities were eliminated by pH control with alkali solution. For selective extraction of cobalt, the aqueous phase removed impurities was equilibrated with different volumes of 0.4 M Cyanex 272 saponified of 50 %. Extraction efficiency of cobalt was about 80 % at first step. Separation coefficient (ßCo/Li) of cobalt and lithium extractions was 206.5. Over 9.0 % of pure cobalt sulfate solution was obtained after stripping with H2SO4 solution.

Jan 1, 2008

By R J. Singh, E. Z. Chacko, Devilal, S. K. Jha, Rina Sahu, Sheshank Shekhar

"Breakouts are one of the biggest problems encountered during continuous casting of steel billets. Billets get cracked locally or break completely in two parts during solidification causing the liquid part of the partially solidified billet to empty inside the cooling chamber. Proper control of important parameters is necessary to avoid break outs during continuous casting. In the present work, the nature of the break outs at a billet caster at Tata Steel was studied. Data analysis was also done for certain casting parameters and the Sulphur tracer test was conducted to understand solidification in the mould. It was found that to reduce the occurrence of break outs, it was necessary to tune the operations based on the grade being cast and the design of the mould tube being used.IntroductionA break out during the continuous casting process is a rupture of the partially solidified shell inside the secondary cooling chamber, causing the contained liquid steel to spill out. In the mid 1970s while continuous casting technology was still in early stage of development, causes of breakouts was not well understood. Today, with technological development much has been understood about breakouts but, most of the understanding has been in the slab casting process wherein due to the higher level of instrumentation, a lot of information has been gained. In billet casting however, due to the geometry of the mould housing with the tube mould, multiplied by the complexity of the multiple strands, instrumentation has not been used and obtaining data for analysis has been difficult.Breakouts at billet casters are still the main hindrances to production. A break out results in a loss in production since the strand which has had a break out is now not available to produce and thus a six strand caster would be reduced to a five strand caster, increasing the time for casting the same tonnage. Additionally extra set up time is required as more often than not a mould change is required in order to have the strand casting again."

Jan 1, 2014

By M. D. Crites

As part of a multi-year program for assessing the viability of chrome-free refractories in copper smelting, converting and refining furnaces, dynamic corrosion tests have been conducted on a series of refractories from the magnesia-alumina system, using a ferrous silicate slag. The corrosion rates of the test refractories are compared with those of a reference mag-chrome brick, and recommendations are made for more in-depth evaluations of the more corrosion-resistant materials.

Jan 1, 1999

By Guillermo A. Vidal

With the introduction of monitoring technologies, process computers and Web services on Industrial Facilities the need for electrolytic processes automation has been set. Recently designed facilities have substantially improved plant layouts, automated cathode processing and copper harvesting. Despite these advancements only limited progress has been accomplished on the electric current distribution of the process. Lately a number of proposals focused on preventing short circuits and balancing cathode currents have emerged. Among these are the AZSA intercell, the Outokumpu double contact, and the Optibar InterCell Plus. Although these intercell bars are clearly superior to the conventional bar, little or conflicting data is available about their merits relative to each other. Consequently, selection of the best intercell bar for most applications is accompanied by uncertainty, which can lead to less than optimum results. A critical evaluation of the performance of the aforementioned bars on the basis of the application is provided, thereby giving the framework and guidelines for the selection of the best bar for each application.

Jan 1, 2003

By Erik Olsson, Gunilla Hyllander, Stefan Schuster, Lena Sundqvist Ökvist, Maria Lundgren, Michael Hensmann, Olavi Antila

"Residual materials from the integrated steel plant itself or other sources often contain valuable compounds of e.g. C and Fe. Dust and sludge have to be agglomerated to be able to recycle to the blast furnace (BF) via top-charging. By injection of the materials, preparation methods in terms of e.g. drying and/or screening only, can be used. Alternative carbon materials (ACM) in terms of BF dust and sludge have been successfully injected up to levels of 60 kg/tHM in the LK.AB Experimental Blast Furnace (LKAB EBF®). Efficiency in recovery of valuable compounds as well as the behavior of undesired elements have been evaluated and are discussed.IntroductionTraditionally, recycling of steel in-plant fines is made via the sinter plant and blast furnace route. Steel plants operating with 100% pellet as ferrous burden and have no sinter plant. There are limited areas for land fill and costs are caused for preparation of landfills and deposit fees. Very fine paniculate dusts or sludges cause decreased productivity and increased coke rate in the sinter plant, and therefore other ways for recycling must be considered. Injecting them into the BF could be an economically and technically feasible alternative. Additionally, as the materials contain valuable compounds of e.g. C and Fe."

Jan 1, 2012

By K. Suseelan Nair

Magnesium alloys containing rare earths are finding increasing applications in space programmes. A number of alloys have been developed and e good data base an the mechanical properties of these alloys is available. However details on metallurgical aspects are found to be sparse in, literature. This paper, at first, briefly reviews the available data on these alloys and subsequently presents the microstructural investigations conducted on quatenary fig-4.9% Zn-1% Rare earth-0.5% Zr cast alley, using optical metallic-graphy, electron probe micro-analysis and X-ray diffraction techniques.

Jan 1, 1989

By Luciano B. Oliveira, Angela O. Costa, Sergio N. Monteiro, Luis Guilherme C. Marques

"Biofuels are gaining a relevant role in today’s world not only as a solution for the decreasing petroleum reserves but mainly as a positive contribution to the efforts in global warming mitigation. In Brazil, since 1975, the replacement of gasoline by ethanol started a so-called PROALCHOOOL program, which is now being complemented with the replacement of petroleum diesel by biodiesel. This biodiesel program was officially created in 2005 with mandatory goals, supported by legislation, of 2% addition in 2008 and 5% addition in 2013 into all commercialized regular diesel. In this work, a critical analysis of the Brazilian biodiesel program is presented. The technical aspects related to the different raw materials, including wastes, available for biodiesel conversion as well as the economical conditions associated with production costs and market logistic are discussed. The environmental benefits associated with the retention of greenhouse gases are also discussed.IntroductionToday the commonly accepted fact that the petroleum world reserves are probably passing through a maximum and start declining in terms of the total amount that can be extracted by existing technologies is motivating significant changes in our society. The continuous increase in the price of gasoline and other liquid fuels is an immediate worrisome and visible consequence. However, more than an economical problem, our civilization is already facing the effects of global warming, due to CO2 emission from burning fossil fuels, mainly from coal and petroleum. It is now realized that a large scale solution for these problems demands the prompt substitution of non-renewable fossil fuels by others that, in addition of being renewable, have a relatively lower contribution to the greenhouse gases."

Jan 1, 2008

By Samuel Senanu, Benjamin Agyei-Tuffour, Lifeng Zhang, Eivind Øvrelid, Adegboyega Nathaniel Femi

"The solar grade silicon ingot produced from directional solidification process usually pushes the impurities to the top and finally cut off and discarded, which leads to material loss. The hard inclusions lead to wire breakages during the cutting of the ingot in wafers. The main kinds of inclusions found in solar grade silicon have been investigated using vacuum filtration: needle-like Si3N4 and lumpy SiC inclusions. Clusters of SiC inclusions and Si3N4 are also found. Surface observations of the scraps before polishing reveals that Si3N4 inclusions are usually bigger and in some cases can be about a few millimeters. SiC inclusions are usually smaller, ~200µm but can be ~500µm in some cases. Inclusions observed after filtration are mainly SiC with diameters ~10µm. Through the vacuum filtration, 99% inclusions can be removed 99%. The possible mechanisms of filtration are cake filtration for the larger sized Si3N4 and SiC inclusions and deep-bed filtration the SiC inclusions. For the directional solidified silicon ingot, an approximate distance of ~10mm gave an encouraging cutoff thickness. The inclusions sizes were below 10µm. Introduction The search for an alternative source of energy to fossil fuel has led to a dramatic increase in the demand for solar energy due to its high dependability (abundant in nature) and environmental friendliness 1). During the last 5 to 10 years, the annual worldwide production of solar cell by the photovoltaic industry has increased to an annual rate of 30 to 40 percent 2). A necessary condition for the maintenance and even an increase of this growth rate is a decrease in the cost of feedstock for the solar cell production 1). The total international production in 1997 was 130 MW worth more than $500 million. In 2004 the consolidated world total production of PV cells increased to 1146 MW or around. $7 billion (Figure 1) 3). Silicon is currently the most dominant semiconductor material used in the PV industry. As shown in Figure 2 3), solar cells consist of two types of material, often the p-type and n-type silicon. Light of certain wavelengths are able to ionize the atoms in the silicon (causing atoms to either gain or lose electrons) and the internal field produced by the junction separates some of the positive charges (“holes”) from the negative charges (electrons) within the photovoltaic device. The holes are swept into the positive or p-layer and the electrons are swept into the negative or n-layer. Although these opposite charges are attracted to each other, most of them can only recombine by passing through an external circuit outside the material because of the internal potential energy barrier. Therefore if a circuit is made, power can be produced from the cells under light because the free electrons pass through the load to recombine with the positive holes."

Jan 1, 2008

By T. T. Chen

Kidd Creek continuously-cast copper anodes are characterized by high levels of Se, Pb and Ag; the anode slimes constituents and their morphologies are controlled by both the anode composition and the casting process. Hollow Cu2Se spheroids and tube-like structures, enveloping Cu-Pb-As oxide and/or Cu2O, are present in the as-cast copper. During electrolysis, the selenides are liberated from the copper and accumulate in the slimes layer; the Cu2O and Cu-Pb-As oxide react rapidly with the electrolyte to form soluble species and PbSO4. Silver, which is present mostly as a solid solution in the anode copper, is also liberated during electrolysis and reacts with the Cu2Se to form (Cu,Ag)2Se. The ultimate composition of the selenides in the slimes layer depends mostly on the Ag and Se contents, but various other elements, including Au and Te, are also structurally incorporated. Although the selenides are the major Ag carrier, metallic silver also is present. A thin layer of Cu2O crystals sometimes forms at the copper surface, and may affect anode passivation. Copper sulphate is a common constituent and serves to agglomerate the slimes. Copper sulphate is present on both passivated and non-passivated anodes, but that observed on the passivated metal is present as a thick compact layer. Copper powder is associated with CuSO4.5H2O only on passivated surfaces.

Jan 1, 1987

By T. L. Baum

External oxidation during in-line heat treatment of TRIP steels can cause problems for the subsequent coating process. This research aims to elucidate the kinetic rates of internal oxidation, external oxidation and decarburization and their interdependence under different gas atmospheres and temperatures. A rolled steel sample chemistry of 0.14 wt.% C, 1.8 wt% Mn, 0.6 wt.% Si and 1 wt.% Al is used as a case study. Thermogravimetric techniques are used to examine the net mass change in a sample during heat treatment and the results show an initial mass decrease and later an increase for particular partial pressures of H2O. SEM-EDS, optical microscopy and glancing-angle x-ray are used to quantify the microstructure. The cross-section of the samples have 4 distinct zones: (i) an external scale, rich in fayalite, (ii) an internally oxidized region with Al, Si and Mn oxides in an Fe matrix, (iii) a decarburized steel region, characterized by large ferrite grains and low carbon content, and (iv) a relatively unaffected steel core with a structure similar to the starting material.

Jan 1, 2006

By Ian M. Ritchie

Cementation or metal displacement reactions such as Cu2+ + Fe Cu + Fe2+ are among the oldest known hydrometallurgical reactions. They are still used in the recovery of some metals and in the purification of process liquors and waste water streams. However, they are often more complex than the stoichiometric reaction would suggest because they involve the simultaneous deposition of one metal onto a second which is dissolving. For example, sometimes a cementation will not take place, even though it is thermodynamically favoured. On other occasions, a cementation reaction will start but come to a halt as the depositing metal blankets the reacting surface. On yet other occasions, side reactions, catalyzed by the deposit, can be important. In this paper, the electrochemical basis of cementation reactions is described. The conditions for each of the complications encountered in these reactions are described and illustrated by examples drawn from a number of hydrometallurgical processes. The cementation reaction between activated carbon and gold thiosulfate is also briefly described, this reaction being unusual in that no dissolution of the carbon occurs.

Jan 1, 2003

By Ana E. Bohé, Georgina De Micco, Gastón G. Fouga

"In this work the reaction between several manganese oxides and chlorine is investigated in the range of temperatures between 650 and 950ºC. The reaction path for the chlorination of MnO is established, which involves recrystallization of high valence manganese oxides (Mn3O4 and Mn2O3) followed by its chlorination. For this reason, to understand the reaction of MnO, the chlorination of Mn3O4 and Mn2O3 has also been studied. The starting temperature for the reaction of these oxides is determined by non isothermal thermogravimetric measurements. The effect of temperature is analyzed, under our experimental conditions the rate of reaction is mass transfer controlled. The activation energy for the volatilization of manganese chloride is obtained which is in good agreement with volatilization enthalpy of MnCl2.IntroductionMany oxide ores which have manganese in their composition undergo chlorination processes during the extraction of refractory metals such as Ti, Hf and Nb. Although several works related with chlorination of manganese oxides were reported, there is no information about the kinetics or mechanism of the manganese oxide chlorination reactions. Okahara et al. studied the chlorination of manganese oxides and established that they react easily above 250ºC. Furthermore, they observed that chlorination of high order oxides is more difficult when there is not a reducing agent [1]. Ivashentsev studied the chlorination of manganese oxides using Cl2(g), CO(g) + Cl2(g) and COCl2(g). He established that the reaction of MnO started at 130ºC with formation of MnCl2(s), he also observed recrystallization of manganese sexquioxide [2]. Finally, the chlorination of manganese nodules from the ocean was studied by Murthy and Reddy [3] with the aim of obtaining valuable metals such as Mn, Co, Ni and Cu. They studied the influence of several parameters like temperature, carbon percentage, particle size and chlorine flow rate in the extraction process."

Jan 1, 2008

By Daniel A. Norrgran

Grinding ball fragments discharging from SAG mills and ball mills causes extreme wear to downstream processing equipment. These ball fragments, recirculating in a milling circuit, will cause excessive wear to sumps, pumps, hydrocyclones, and interconnecting piping. A magnetic separation system to remove grinding ball fragments from the mill discharge has been developed and successfully applied in the milling circuit. This magnetic separation system - termed Trammel Magnet - was first applied at the Escondida copper concentrator in Chile. The Trommel Magnet consists of an arc of permanent magnets mounted at the discharge end' of the tommel screen. The magnetic arc attracts the ball fragments and removes them from the process stream. This retrofitted magnetic separation system removed 126 metric tons of ball fragments from the circulating load of a. single ball mill in the initial 24 hour period. The mill has since stabilized and the magnetic separator is currently removing 7 metric tons per day of ball fragments. The retrofit of the Trommel Magnet has: 1. Extended the pumpp life and the hydrocyclone life approximately 300 percent. 2. Provided a 5 percent increase in the throughput of the mills by removing grinding ball fragments that contribute very little to the grinding process. Variations of the Trommel Magnet have also been developed for removing grinding ball fragments directly from the mill discharge without the use of a trommel screen. In each case, permanent magnets are used to collect the ball fragments from the mill discharge stream prior to reporting to the sump. These other systems have been designed and fabricated for in-plant test work.

Jan 1, 1999

By J. M. Zhuang

Lignosulfonates, by-products of the sulfite pulping process, have been utilized in a process [1, 2] to treat acidic rock drainage (ARD). This process is referred to as the LignorTM process. In the present study, lignosulfonates were found to protect lime from developing an external surface coating, and hence to favor its dissociation. Further, the addition of lignosulfonates to ARD solutions increased the clotting and settling rate of the formed sludge. The capability of lignosulfonates to form stable metal-lignin complexes makes them very useful in retaining metal ions and thus improving the long term stability of the sludge against leaching. The LignorTM process involves metal chelation with lignosulfonates, ARD neutralization by lime to about pH 7, pH adjustment with caustic soda to 9.4 ? 9.6, air oxidation to lower the pH to a desired level, and addition of a minimum amount of FeCl3 for further removal of dissolved metals. The LignorTM process removes all concerned metals (especially Al and Mn) from the ARD of the Britannia Mine (located at Britannia Beach, British Columbia, Canada) to a level lower than the limits of the BC Regulations. Compared with the high density sludge (HDS) process, the LignorTM process has many advantages, such as considerable savings in lime consumption, greatly reduced sludge volume, and improved sludge stability.

Jan 1, 2003

By Arthur G. Hunt

Smelting using the direct-to-blister process commenced at Olympic Dam on 31 July 1988. The unique nature of the Olympic Dam ore body led to the selection of the direct to blister smelting process. Significant improvement in the design of the furnace and the understanding of the fundamentals of the process and its operation has occurred in the 10 years of operation. The paper will discuss the operation of the #1 Smelter and the design, preparation for start up and early operating experience of the #2 Smelter.

Jan 1, 1999

By G. G. Barbante

Copper anode slimes are a valuable source of the precious metals, and selenium and tellurium. They are mineralogically complex and this has led to a great variety of process flowsheets for treating them. The traditional pyrometallurgical method utilises oxidation in a reverberatory furnace, but has numerous shortcomings. Recently deep-bath intensive smelting methods have been developed for use in the larger refineries. Despite these process advances, the thermodynamics of the reactions involved remains poorly understood. An initial description of the thermodynamics of slimes smelting is presented, but is severely limited by a lack of basic data. It is shown that slimes smelting is superficially similar to copper converting, but has many unique features. More basic thermodynamic data on selenium-based systems are needed before the process model presented can be further refined, and work in this direction has already commenced.

Jan 1, 1994

By R. Parada

A real-time dynamic simulation model has been developed to characterise the flash furnace operation at the Chagres smelter. This model permits the operators to plan the process to meet the Peirce Smith converters' schedules and feed the acid plant with gases that satisfy its best operating efficiency range. Essential control parameters for the furnace (process air enrichment, oxygen coefficient and supplementary heat) are calculated to satisfy process targets such as matte grade, slag silica and matte/slag temperatures. These calculations are carried out with a real-time simulation. Flash furnace control and operational stability permits setting up control strategies that streamline the flow of copper to converters and of sulphur to the acid plant.

Jan 1, 1999

By S. J. Macnaughton

The Olympic Dam deposit in South Australia contains 2% copper and 0.06% uranium, which are present as bomite, chalcocite, chalcopyrite, uraninite, coffinite and brannerite. The copper is principally recovered using flotation. The flotation tailings, which contain the bulk of the uranium, and typically 0.3% copper, are leached using sulfuric acid and an oxidant at atmospheric pressure. This paper describes the results from a detailed investigation of the leaching behaviour of this ore. The influence of acid strength, Fe3+ concentration, redox potential and temperature on the dissolution of uranium and copper minerals was studied. Experimental data were obtained from extensive batch leach tests. Mineralogical studies, including SEM analysis of individual mineral grains, were also carried out. The maximum extraction of uranium determined experimentally was in good agreement with that predicted from SEM determination of the proportion of refractory brannerite in the ore. The leaching rate of copper was found to be independent of acidity over the range 20 g L-' to pH 2.0, but was strongly dependent on temperature and Fe3+ concentration. Uranium extraction showed a weak de endence on acidity, Arrhenius temperature dependence and a complex co-dependence on F>+ concentration and redox potential. A kinetic model has been developed, which predicts copper and uranium dissolution. This model will be incorporated into a more comprehensive model that can be used to predict leach performance and reagent consumption for specific ore samples.

Jan 1, 1999

By Wang Yun-yan

In order to examine the adaptability and the kinetics of leaching different gold ores in alkaline thiourea system, six kinds of gold concentrate and/or calcine with different physical and chemical properties were chosen as objects. The leaching behaviors in alkaline thiourea system with high stability, acidic thiourea system and alkaline cyanide system were compared. Changes of phase, surface appearance, particle distribution and specific surface area of six kinds of gold ores before and after leaching were studied in virtue of modern analytic techniques, e.g., XRD, SEM, and so on. The results indicate that alkaline thiourea solution can be used to leach gold ore, for oxidized gold concentrate removed arsenic by microbe pretreatment(4#) the leaching rate of gold is up to 82.68%, such conclusion overthrows the parlance reported that pH value must be less than 1.78, or gold can not dissolve in thiourea solution. Chemical components and phase are related to gold leaching rate, different gold ores are fit for different leaching system, and alkaline thiourea solution is suitable for the pretreated oxidized gold ores with low content of sulfur and in which the main phase was SiO2, phase almost does not change after leaching basically. Generally speaking, when leaching in alkaline thiourea solution, surfaces of gold ores with glaze change greatly to ones with coarseness, distinct trace and holes of corrosion. Particle size decrease and specific surface area increase of gold ores after leaching in alkaline thiourea solution with high stability except gold concentrate of Zhongyuan gold smelter(5#).

Jan 1, 2006

By Xiaodi Huang, Matthew Andriese, Zheng Zhang, Jiann-Yang Hwang, Zhiwei Peng

"The thermal decomposition and regeneration behaviors of wüstite were investigated by in situ high temperature X-ray diffraction (HT-XRD) under non-isothermal condition at heating rate of 4 K min-1 in vacuum ranging from 294 K to 973 K. Wüstite on heating decomposes to magnetite and iron up to 823 K, above which it exhibits marked tendency to regenerate. Investigation of thermal stability of the reaction system shows that the decomposition proceeds under kinetic reaction control while the regeneration is under thermodynamic control. Kinetics study based on the Coats-Redfern integral approximation method indicates that the decomposition reaction follows a Komatsu-Uemura model-based diffusion-controlled kinetics with activation energy of 32.860 kJ mol-1. The thermodynamics analysis of regeneration reaction demonstrates that wüstite regenerates at lower temperature than stoichiometric ferrous oxide.IntroductionOwing to its importance in preparing various magnetic ceramic/metal nanocompostites or nanocrystals with high values of coercivity for the application as recording media, wüstite (non-stoichiometric ferrous oxide) has been attracting the attention of scientists over a long period [1-6]. The thermal behavior of wüstite was investigated by several researchers and phase transformations due to thermal decomposition and regeneration of wüstite during the heating in a specific temperature range was observed [7-9]. In spite of wüstite being found to dissociate to magnetite and iron at temperatures lower than 848 K and then regenerates at higher temperature, a clear understanding of the reaction mechanisms is clearly lacking [9]."

Jan 1, 2012