Search Documents

By Josef Martinsen

This paper describes two-lane dual motorway tunnels under construction in Bergen. The tunnels are part of a by-pass motorway system throuth the most congested area of the city of Bergen. The tunnels are unique due to their length, heavy traffic, longitudinal ventilation system and the use of a tunnel boring machine, or "TBM", to excavate through hard rock. The tunnels are being built by The Norwegian Public Road Administration and the TBM was delivered by the Robbins Company. The diameter of the TBM is 7.8 m and the tunnel profile is cut by conventional drill and blasting methods in the tunnel's lower half to attain a two lane motorway tunnel. This paper also describes proposed fjord crossings along the Norwegian west coast where the TBM may be used due to its great advantages in comparison to conventional drill and blasting methods.

Jan 1, 1987

By James N. L. Lukanuski

Three porphyry copper districts in southern Arizona are partly overlain by post-ore fanglomerates which share certain physical and petrologic characteris¬tics and which may comprise a distinct and significant class of rock. These units are the Locomotive fanglomerate of Ajo, the Helmet fanglomerate of Twin Buttes-Mission-Pima, and the Cloudburst formation of San Manuel-Kalamazoo, termed "Locomotive-type fanglomerates" herein. Post-ore units at Poston Butte and Lakeshore, Arizona, and Sar Chesmeh, Iran, also appear to fit this class. "Locomotive-type fanglomerates" are composed of poorly sorted conglomerates, lenticular sandstone beds, andesitic to rhyolitic flows and tuffs, and unique monothologic landslide breccias. They contain fragments of holyokeite - - a rare oligoclase lava of porcellaneous appearance. Their basal contacts are considered to be depositional and overlapping, sometimes complicated by later low-angle faulting. They arc quite different than the younger Cila, Pantano, and most "Whitetail" alluvial beds, and the older Amole, Recreation, Claflin Ranch, etc. elastics; in particular they are thinner and less widespread. Their ages are Eocene to late Oligocene. "Locomotive-type fanglomerates" may be genetically related to porphyry coppers as products of subsequent differentiation and volcanism, and sedimentation in short-lived basins of restricted area and extreme relief. They might be utilized as reconnaissance guides to target areas and as structural guides within target areas in the southwestern U.S., Northern Mexico, and elsewhere.

Jan 1, 1975

By Richard Klimpel

1. Introduction Laboratory and industrial grinding tests have shown that the process of size reduction can be significantly influenced by chemicals added to the powder or slurry being ground. The terms grinding aid or grinding additive refers to a substance which when mixed into the mill contents causes an increase in the rate of size reduction. The increased rate can be used to grind a higher feed rate to the desired product size or it can be used to produce a finer product size at a fixed feed rate. Whether the use of a grinding aid is justified in any given situation depends on the cost of the substance versus the improvement of output or product quality obtained with its use. Obviously, an expensive chemical must be effective in very small concentrations if it is to be economically justifiable; the cost criteria is calculated on the basis of the cost of the grinding additive per ton of material ground. Although there is direct experimental verification of the advantageous effect of grinding additives, no sound scientific explanation has yet been offered which explains or predicts the general behavior of additives. Rose and Sullivan have summarized most of the work undertaken prior to 1950 and Hartley, Prisbrey, and Wick have recently prepared an updated synopsis of the grinding additive literature. Many of the studies reported consist of subjecting materials with simple geometric shapes to some type of hardness or controlled single fracture test. On the other hand, a number of the studies were carried out on operating industrial scale mills, with little control or precise monitoring of the effect of the additives.

Jan 1, 1977

By J. A. Farinelli

In the Appalachian region of the United States, approximately 40% of the underground coal reserve base exists in seams 0.7 - 1.1m thick. These seams are, in general, often of premium quality and are frequently accessible through above-drainage drift-type openings. Unfortunately, there are no apparent advantages to mining thin seams, if quality is disregarded. The thin-seam mine is faced with the same legal and economic pressures as any other underground coal mine. But in addition to these common problems, thin-seam operations must also deal with the unique problems associated with mining at such a restrictive height. Small-scale, short-lived operations appear to be the most feasible means of mining these reserves. The purpose of this paper is to evaluate the production and safety potential of various thin-seam mining systems. Recommendations will be made regarding present and future thin-seam operations.

Jan 1, 1987

By S. B. Leonov, K. I. Popov, S. B. Polonsky

The offered technological line includes a flotation pulp air conditioner operating on the impact-mechanical effect and two column apparatuses with a descending pulp-air flow mounted in series. The technology developed makes it possible to increase considerably the valuable component in the concentrate simultaneously with a reduction in energy consumption for the flotation process. The experience achieved with the technology showed the possibility for obtaining sulphide silver-bearing ore superconcentrates with the noble metal content 2-10 times higher than that in the concentrates obtained by the conventional technology. The same results were obtained in the process of calcium-bearing boron-silicate ore-dressing.

Jan 1, 1995

The ventilation of a mine is one of the key elements to a successful mining operation. It is, or should be, one of the primary concerns of the mining engineer at an underground mine. Too frequently, however, insufficient thought is given to future requirements. As a result, the mines suddenly find themselves with ventilation problems that cannot be corrected economically, or in short order, and have to suffer the consequences of being on the verge of having units shut down from time to time until the venlilaltion system can be improved. Insufficient ventilation in capital-intensive mining can cause production losses, the values of which far outweigh the significant costs of providing and operating an adequate ventilation plan. Many theories, and techniques in planning and control of underground ventilation systems have been developed over the years . It is the intent of this paper to point out some of the fundamental concepts, from the practical point of view, in the design and operation of a ventilation system, with special reference to underground mines using a room-and-pillar method.

Jan 1, 1986

By Haydn H. Murray

Kaolins and bentonites of economic importance in Australia and New Zealand are described. Clays that are used for structural clay products are not discussed. Residual, hydrothermal, and sedimentary kaolins are utilized including clays associated with coal measures. Bentonites are sedimentary and residual. Very little kaolin and no bentonite is exported presently, but this will change in the near future as transportation costs continue to escalate. Many areas of Australia, in particular, where kaolins are known to occur have not been investigated to determine the quality and quantity of the deposit.

Jan 1, 1982

By Howard C. Homeyer

Coal and water are the two basic external feedstocks required for a coal gasification project. The WESCO project in northwest New Mexico, a joint undertaking of Texas Eastern Transmission Corporation and Pacific Lighting Corporation, will require about 25,000 tons of coal and approximately 7.5 million gallons of water each day to produce 250 million cubic feet per day (MMCFD) of pipeline quality substitute natural gas (SNG). The coal and water supply arrangement with Utah International, Inc. assures the project of an adequate supply of these two vital feedstocks.

Jan 1, 1974

By D. T. Iseley, A. L. Atta-alla

INTRODUCTION The extension project of the East Line Subway of Atlanta's subway network includes the construction of two single track transit tunnels under Interstate Highway 285. The project will be in DeKalb County, Georgia. The length, width, and height of each tunnel are 54.25, 6.3, and 7.2 m (178, 21, and 23 ft) respectively. The ground cover above the tunnel crown ranges from 1.5 to 3.25 m (5 to 11 ft). A soil pillar about 5.5 m (18 ft) wide will remain between the tunnels. The construction of each tunnel includes (i) installation of 21 steel soil support pipes of 75 cm (30 in) diameter, (ii) jet grouting 15 soil cement shafts of 60 cm (24 in) diameter in the soil under the pipes, (iii) contact grouting behind the tunnel lining and between soil support pipes and pavement, (iv) excavation of soil inside the soil support arch, and (v) installation of steel pile foundation, steel sets, and permanent tunnel lining of cast-in-place concrete, all as shown on the cross section in Fig. 1. The soil profile can be described from top to bottom as cement/asphalt concrete pavement, a fill layer consisting mostly of stiff sandy silt/firm silty sand, a residual soil layer consisting mostly of silty sand/sandy silt, partially weathered rock, and solid rock.

Jan 1, 1991

By T. M. Yegulalp

One of the important factors affecting the determination of the minimum number of increments in a gross sample of coal is the variance component due to segregation. The segregation variance may be estimated by following the ASTM standard procedures. Since the estimate itself is a random variable, it is important to test if the value obtained is due to chance causes. This paper introduces a statistical test, based on the procedures published by ASTM, to test if the segregation variance is significantly greater than zero.

Jan 1, 1986

By M. C. Roberts

The success of any industrial mineral project requires an accurate forecast of the demand for the material. This paper develops a general method of evaluating these needs and applies it to the case of graphite. The basic method is to explain graphite consumption in each of its major uses by the output and manufacturing technology of the using industry. Once these underlying factors are determined, they can be projected to establish future requirements. This demand forecast is critical to the evaluation of a new source of supply, such as the graphite resources of upper Michigan.

Jan 1, 1989

By John Todhunter

Longwall mining is certainly not new in the United States, having first been used in the late 1800's in Illinois, but the surging acceptance of the method is relatively new. The number of longwall installations in this country are nearly doubling annually as this method continues to prove itself as a coal producer's delight terms of operating cost, performance and safety. Since 1951, several longwall installations have been tried in Barnes and Tucker Company operations. Although all efforts actually proved that the system itself could be used in prevailing conditions, it was not until 1967 that a unit was put in use that proved competitive with regular mining equipment, both conventional and Continuous.

Jan 1, 1968

By D. Watson

The Henderson mine has more than 20 years experience and has placed a combined total of more than 400,000 m3 (520,000 cy) of shotcrete and concrete. Over the last 20 years the mine has used a variety of equipment for placing concrete, wet shotcrete and dry shotcrete and is constantly trying to cut costs and increase efficiencies. Henderson has recently received a state of the art wet shotcrete placer, automated its batch plant, fabricated a mobile concrete form jumbo and is soon to receive a new concrete transport truck.

Jan 1, 1992

By Duk-Won Park

Since geologic anomalies are one of the governing factors of instability of underground openings, it is extremely important to know in advance the locations and extent of these anomalies such as faults and weak zones. At an underground coal mine in the Black Warrior Basin, core drilling was conducted to find a fault in an area where they were planning to locate longwall panels and possibly a shaft. Core logging did not provide sufficient information to delineate the exact location, strike, and dip of the fault. However, a high resolution reflection seismic study successfully solved this problem. This experience proved the seismic exploration technique could be used for premining coal exploration by reducing drilling costs and providing more accurate and detailed information about geologic anomalies.

Jan 1, 1988

By A. D. Wunderlich

Providing a safe & secure environment for your employees and other company assets is absolutely necessary in our litigeous society. Security hardware is no different than computers or other technical equipment, in that new equipment is developed each year that makes older equipment obsolete. This presentation will help to explain how your existing security system and security procedures can be updated to meet industry standards without the expenditure of a great deal of money. If you are concerned about potential security problems and how to address these problems, this presentation is a must.

Jan 1, 1995

By Kostas Fytas, Sebastien Perreault

This paper presents EOLAVAL, an integrated mine ventilation design software. In its new expanded version it is a user friendly and fully interactive computer package. The features of the new version are a graphics interface fully compatible with Autocad files, an integrated database of fan characteristics and the optional use of the thermodynamic approach in carrying out network simulations. This software can be used in underground mine ventilation planning: mine ventilation network analysis and simulation, economic design of airways, auxiliary ventilation design, calculation of a mine air heating plant, and evaluation of the natural ventilation and pressure losses in a mine shaft. This paper presents a case study illustrating the use of the computer package in mine ventilation design.

Jan 1, 2002

By G. M. Bernard

An overview presentation of the fast-track start up of Cerro Colorado, a new copper heap leach project in Chile's Atacama' desert. A brief explanation 'of location of the property, exploration history, geol-ogy, reserves and development are presented. The overview includes mining, crushing, agglomeration, and the solvent extraction-electrowinning recovery process. Challenges and requirements specific to heap leach systems will be addressed and analyzed. A detailed description will be given of the mobile heap leach conveying and stacking systems used in the building of heaps for on-and off-pad operations.

Jan 1, 1995

By George A. Lawrence

A new super-large 100 m3 (3500 A3) pneumatic mechanical flotation cell is now available to meet future mineral processing challenges. Several innovative design concepts represent a marked departure from conventional flotation cell designs. The radial discharge from the pump action rotor and the overhung vane type stator is contained in a conical bottom cylindrical tank with no dead comers. Peripheral launders collect froth overflowing the entire circumference of the tank and these launders are of a hexagonal design permitting cells to be nested together in a honeycomb fashion. This new flotation cell is powered by a custom designed hydraulic motor package that provides infinite speed control in individual cells and a soft start under load

Jan 1, 1993

By T. J. van der Walt

This paper proposes a new methodology to model ill- defined processing operations using neural nets (NN's). A process with many variables (large dimensionality) cannot be modelled adequately if limited process data are available. This problem of multi-dimensionality is addressed and an approach suggested to reduce the dimensionality using NN's. The result of this modelling methodology is a combined model of phenomenological expressions and NN's. The model can successfully be incorporated in a dynamic simulator of the process. A new approach to conduct modelling on the basis of continuous data collected directly from an industrial processing unit, is also proposed. The modelling methodology is applied to a typical processing operation, the resin-in-pulp (RIP) process.

Jan 1, 1992

By Jr. Neudecker

Rock melting technology can provide in-situ glass liners in nuclear waste package emplacement holes to reduce permeability and increase borehole stability. Reduction of permeability would reduce the time and probability of groundwater contacting the waste packages. In-creasing the stability of the storage boreholes would enhance the retrievability of the nuclear waste packages. The rock melting hole forming technology has already been tested in volcanic tuff similar to the geology at the proposed nuclear waste repository at Yucca Mountain, Nevada.

Jan 1, 1989