Search Documents

By Timothy G. Shuttleworth

In the late1970s, mineral processing plants producing copper sulfide concentrates and oxide leaching feedstocks went online with operating tonnages that exceeded traditional installations. This created a need for larger capacity belt conveyors and apron feeders. Apron feeders are slow moving, heavily loaded conveyors that feed a deep bed of ore from a bulk holding location (a bunker) as a controlled stream, often into a large capacity crusher. Apron feeders use sprockets and caterpillars, while belt feeders use rubber belts with motorized head pulleys to convey the material. The damaging of belts and clogging of transfer points from tramp iron required larger magnetic separators and the removal of tramp metal cannot prevent these serious problems. Corrective action at this location is important for two reasons: Removing tramp iron early in the ore stream protects downstream equipment from potential costly damage. Installing apron feeder magnets before the primary large capacity crusher means that secondary and tertiary crushing steps (made up of multiple parallel units) operate more efficiently, since tramp metal is removed at the onset.

Jan 1, 2011

By I. E. Lewis, W. R. Hopkins

Flowsheet improvements, such as series/parallel SX plant configurations, discontinuation of plant sumps and improved filter pumping concepts, the use of in-settler baffle systems, and the Krebs and combined mixer-settler designs offer opportunities to reduce SX plant cost. Today's plants employ permanent cathodes and mechanical stripping, and the increased capital cost can be offset by labor savings and higher current densities. The wider use of HDPE and new cell construction materials also reduce capital cost. The "Portelex" type of relocatable design embodies such new, cost-saving measures in a simple basic plant. Organic inventory and losses are reduced by new, fast-settling, hybrid organic reagents with improved kinetics and selectivity.

Jan 1, 1991

By C. Salcedo, J. Vallance, J. Sáez, M. Robles, J. Spangenberg, S. Rosas, L. Fontboté

The Tambomachay ore deposit (13°28'36.78"S, 71°57'35.98"W, about 6 km north of the town of Cuzco, Peru) consists of Cu hosted in arkosic red beds of the Kayra Formation (Lower Eocene). Bornite, chalcopyrite, chalcocite, covelite, digenite, malachite, and chrysocolla occur disseminated in thin layers and in veinlets. The occurrence of the copper ores in a part of the red bed sequence containing green reducing layers, the presence of organic matter in interstices between the hypogene sulfides, and the sulfur composition of the copper sulfides (δ34S values between -16.9 and -12.4‰ vs VCDT) pointing to bacterial sulfate reduction, are strong arguments to propose that mineralization was caused by copper-bearing oxidizing saline basinal fluids that precipitate copper sulfides when they meet reduced sulfur in an organic matter-rich horizon. Faults parallel to the regional Tambomachay Fault could have acted as feeders for oxidizing basinal copper-bearing fluids. Fluid migration was probably driven by tectonically-induced topography gradient. INTRODUCTION A number of red bed Cu occurrences are known in the Cuzco region in the early Eocene – early Oligocene San Jerónimo Group (Gregory, 1916; Carlotto et al., 1996, 2011; Loza et al., 2004). In the past, copper ores were extracted in several small-scale mines in the surroundings of Cuzco, including Tambomachay, Tipón, and Zurite in the Cusco province and Ushpa, Guilda, Giovanna, and Langui in the Sicuani Province. The abandoned Tambomachay Mine (13°28'36.78"S, 71°57'35.98"W), about 6 km to the north of the town of Cuzco (Romero et al., 2015; Salcedo et al., 2017, Fig. 1) was chosen as the main site for the present research aimed to better study the genesis of these copper occurrences. Results deriving from fieldwork, microscopic characterization of ore and host rock, and sulfur isotope determination suggest that the key factor for the genesis of the copper ores is that copper transported by oxidizing basinal fluids is trapped by reduced sulfur of bacteriogenic origin located in a part of the red bed sequence that shows intercalatins of green reduced horizons.

Jan 1, 2019

By L. Alan Weakly

At a time when the US mining industry is struggling to emerge from a lengthy recession, the burden of new, unnecessary regulations could shorten the life of, or be fatal to many domestic mining companies. The possibility of new restrictions on the use of diesel equipment operating in underground mines is one example of unnecessary regulations. These could cause serious harm to the economic health of many mining companies. Whether future health-related Mine Safety and Health Administration (MSHA) regulations restricting the use of diesel equipment are unnecessary, depends on whether these restrictions are supported by fact or created in a political environment. The mining industry has benefited from the use of diesel equipment in underground metal-non-metal and coal mines for more than 50 years. Since first introduce to underground mines in the early 1940s, the use of diesel equipment has grown in numbers and size. During this time, the mining industry in America has achieved much higher productivity rates and improved safety. Although all these gains cannot be attributed to the greater use of diesel equipment, a high percentage can be. I began my professional mining ca¬reer in 1970 working in the Missouri lead mines. At that time, the use of diesel equipment was well established in metal-non-metal mines throughout the United States and many parts of the world. As director of mining research for St. Joe Minerals Corp. (now The Doe Run Co.), I was involved in research to improve mining productivity and safety. This involved investigating the better and safer use of existing or new mining methods, products, equipment and people. Within this group, diesel equipment had the single largest positive impact.

Jan 1, 1993

The concept of "classification is expanded beyond the performance of the classifying equipment to include all aspects of the fines removal system of the grinding circuit. Design and operating parameters which affect fines removal are identified and discussed, and a quantitative index for circuit fines removal effectiveness is defined. This approach lends new interpretation to certain observed phenomena, and suggests useful guidelines for circuit design and operation.

Jan 1, 1985

By Ernest A. Draeger, James W. Collins

Water only cyclones, sometimes referred to as hydrocyclones, are one of the newest types of coal processing equipment. These devices have achieved wide acceptance as fine coal cleaners in the past decade. Many metallurgical coal plants employ water only cyclones to process 0.5 mm x 0 size coal. Some of these plants have as many as 40 to 50 305-mm-diam units with each unit receiving as much as 9 t/h of raw feed. The growth in the utilization of hydrocyclones is due partly to the energy shortage, partly to the general increase in over-all coal preparation, and also because of a need for a simplified fine coal (0.5 mm x 0 size) gravimetric separator. Large diameter water only cyclones are also available and in use to process feed sizes up to 32 mm in size. However, the size normally employed for cleaning 0.5 mm x 0 coal are 356 mm or 305-mm-diam for single-stage circuits. In two-stage circuits, the secondary units are normally the same diameter as the primary units or smaller, such as 203-mm-diam. By using the small diameter cyclones and treating a closely sized feed, 0.5 mm x 0 only, it has been found that the probable error or imperfection of the water only cyclones is comparable to that obtained on the same size fraction treated in a large 610-mm-diam heavy media cyclone washing 38 mm x 0. The water only cyclone can approach the efficiency of a heavy media cyclone when cleaning fine solids because it creates its own dense media by accumulating high specific gravity particles in the wide angle conical section of the cyclone. A cut-away cross sectional view of a water only cyclone is shown in Fig. 1. It is also true that when treating a wide range of sizes (38 mm x 0) in heavy media cyclones, the smaller size particles (0.5 mm x 0) separate in proportion to the split of the media through the cyclone rather than by particle density.

Jan 8, 1980

By Ying Lu, Jeffrey C. Johnson, Chen-Luh Lin, Jan D. Miller, Sindhoora Puvvada

The amount of energy used to break rock is of interest in mine-to-mill operations to minimize energy consumption during blasting at the mine site and comminution at the processing plant. In this research, a direct energy measurement was made using high-velocity impact to cause breakage of long granite cores, and to study the energy dissipation along the entire bar length. The results show the formation of three zones of damage — fragmentation, fracture and elastic — that have been characterized in 3D using X-ray tomography. The fragmentation zone of the granite bars was studied in detail to describe the particle size distribution and the particle shape characteristics. The experimental energy dissipation in the fragmentation zone was found to be in close agreement with the expected energy calculated from the Bond work index (BWI) equation [1] when the anisotropic granite particles in the fragmentation zone are defined by length rather than by sieve size. The results increase our understanding of rock breakage and energy consumption and may find future applications in mine-to-mill operations.

By LUKAS FAHLE, JURGEN F. BRUNE, ANDREW J. PETRUSKA, ELIZABETH A. HOLLEY, Gabriel Walton

Adverse ground behavior events, such as convergence and ground falls, pose critical risks to underground mine safety and productivity. Today, monitoring of such failures is primarily conducted using legacy techniques with low spatial and temporal resolution while exposing workers to hazardous environments. This study assesses the potential of novel simultaneous localization and mapping (SLAM)-based light detection and ranging (lidar) data quality for rapid, digital and, eventually, autonomous minewide underground geotechnical monitoring. We derive a comprehensive suite of quality metrics based on tests in two underground mines for two state-of-the-art mobile laser scanning (MLS) systems. Our results provide evidence that SLAM-based MLS systems provide data of the quality required to detect geotechnically relevant changes while being significantly more efficient for large mine layouts when compared to traditional static systems. Additionally, we show that SLAM-specific processing can achieve an order of magnitude better relative accuracy relevant for change detection than quality metrics derived from traditionally deployed tests would suggest, while reducing SLAM-drift error by up to 90 percent. In collaboration with an operating block-caving mine, we confirm these capabilities in field tests on a minewide scale and, for the first time, demonstrate methods of rockfall detection using MLS data. While more work is required to investigate optimal collection, processing and utilization of MLS data, we demonstrate its potential to become an effective and widely applicable data source for rapid, accurate and comprehensive geotechnical inspections.

Jan 1, 2023

By Y. Nan

A new computer simulation model for the analysis of underground coal mine production systems in the Peoples Republic of China is presented. As a case study the model was used to analyse the railway system of an existing underground coal mine. Some results of this first application are given in this paper and some conclusions of common interest for underground rail haulage systems are discussed.

Jan 1, 1986

By Chaoxun Zhao, TAIYOU LI, JIAQI JIN, Chen-Luh Lin, Jan D. Miller

A large portion of the energy consumed in copper concentrators is used to reduce the particle size of the feed by crushing and grinding. The cost of metal production could be reduced if low-grade particles of centimeter size were removed prior to further processing. Two copper sulfide ore samples (3 × 1 cm) from Arizona were analyzed by micro X-ray computed tomography (Micro-XCT) to determine the grade of copper sulfide in each particle. For copper ore sample A, a significant number of particles contained very low amounts of copper, while some particles had copper sulfide grains of millimeter size. Based on Micro-XCT, it was expected that 85 percent of copper for sample A could be recovered at 65 percent of mass rejection during preconcentration by sorting. However, in sample B (a different copper ore), distribution of copper sulfide was dispersed primarily in each ore particle, so for the particle size class of 3 × 1 cm, liberation of copper sulfide and gangue minerals was not significant. In view of the XCT results, dual-energy X-ray radiography was used as a basis for sorting. Pilot-scale X-ray sorting of sample A (10 × 1 cm) showed 31 percent rejection of a 0.08 percent Cu gangue product with a corresponding recovery of 90 percent copper.

By Lihong Zhou, DAVOOD BAHRAMI

A reliable and stable ventilation system is essential to the safe operation of underground mines. The stability of a mine ventilation system becomes extremely critical when responding to a fire incident, as an unstable ventilation system will pose a risk of airflow reversal. The reversed airflow could bring fire contaminants, such as toxic gases and smoke, unexpectedly to working areas. In the past few years, there has been a growing interest in the study of ventilation network stability using the concept of resistance sensitivity, which is described as an indicator of how the airflow in an airway is reacting to a resistance change of other airways. Several methods of calculating the resistance sensitivity in a mine ventilation network have been developed by researchers and scholars around the world. However, those proposed methods rely heavily on a vast number of mine ventilation simulations, which is time-consuming and computer-resource intensive, especially for a large-scale mine ventilation network. In this study, a derivative method calculating the resistance sensitivities with a single mine ventilation simulation is developed and implemented into the MFIRE mine fire simulation software. The results from the derivative method were verified against the results from a traditional method. The derivative method is proved to be reliable and accurate.

Dec 1, 2022

By DEBASHISH MISHRA, SOMU MANDAL, ASFAR MOBIN KHAN, JAI KRISHNA PANDEY, NIROJ KUMAR MOHALIK, SANTOSH KUMAR RAY

Coal is a low-cost fuel with high calorific value. Statistically, the global coal mining industry suffered 12,489 fatalities in 104 reported mining accidents from coal dust explosions during 1900 to 2020. This review article discusses the occurrence, mechanism and explosibility parameters of coal dust explosions and presents a literature survey of the laboratory and computational fluid dynamics (CFD) simulation methods of studying them, as well as a comparison of the two methods.

Feb 1, 2023

By G. L. Dollinger, W. H. Hamilton

INTRODUCTION Design and development of new products generally proceeds through a phase of initial development and discovery based on the evolution of existing arts, followed by technical innovation and development based on both pure and applied research. The development of the mechanical tunnel boring machine (TBM) has followed a similar pattern, with the first machines closely resembling continuous coal miners. In general, however, the design of TBM's to date has been more a result of evolution and discovery than of new technical innovation, even though large sums of money have been spent on research and development. In particular, the results of experimental laboratory and field investigations have had little effect on tunnel boring machine design, and the better performance of TBM's today over those of 10 or 15 years ago, is due more to increased mechanical reliability and greater operating experience, than to improvements in penetration rates and rock fracture capability. The improvements made, have been mainly by the machine and cutter manufacturers who recognize the greater efficiency and economic advantage of utilizing large single row cutters with high load capacity along with large edge spacing. Are there any improvements to be made, therefore, in TBM performance without new and dramatic technological breakthroughs? Can TBM manufacturers design greater performance into their machines by a logical extension of the present art, and by applying what has been learned in the laboratory and field? Some, for example, believe that the kerf cutting system of boring rock is at, or close to, its opti¬mum and little improvement can be made in the present TBM concept.

Jan 1, 1979

By R. Todd Swinderman

Impact cradles are installed below the belt in conveyor loading zones to cushion the forces from material loading. In this paper, the author will discuss the need for and then explain the new CEMA standard for engineering of impact cradles. He will review the engineering theory and work through an example to demonstrate the assumptions used in the standard do not inappropriately affect the CEMA rating system.

Jan 1, 2002

By Tim McMahon

"A slurry is any combination of liquids and solids where solids make up more than 10 percent of the mixture. Mining operations create various types of slurries from processes such as dewatering, bitumen extraction in oil sands, concentrator plants, milling operations, tailings, lime addition and so on. The mines then transport these slurries through pipelines (Fig. 1).Slurry valves are used when the mine needs to transport ore a long distance and there are no other viable transportation methods, such as roads or railroads.Severe service valves must be used in slurry applications and they must be tested to ensure reliability. This article describes how Emerson designs and tests its Fisher valves for use in mining slurry applications.Slurry pipeline valvesWithin a slurry pipeline system, valves are required as part of the pumping stations, choking stations and isolation stations. There may be multiple pumping stations depending on the length of the pipeline or the terrain it crosses. Choking stations are used to reduce the velocity and the pressure in the pipeline, either before a pumping station or at the end of the pipeline, and to ensure the pipeline does not slack (remains full and pressurized). Isolation stations exist so that a pig (a device sent through a pipeline to clean or inspect the pipe) can be inserted or removed from the pipeline.Typical valves used in a slurry pipeline are severe service ball valves. The valves use floating balls that are held between the seats and are not pinned or permanently attached to the shaft that rotates the ball. The inside diameter of the ball typically matches the pipeline inside diameter, enabling the pipeline to be cleaned or inspected with a pig.They can be built to accommodate the high pressures required for the typical slurry pipeline. These pressures can require up to ASME Class 2500 valves and flanges. The valves can get qlarge, up to NPS 36 inches.Specialized segmented ball valves and slurry knife gate valves are also used in some slurry applications when pressures are lower, in the ASME Class 150-300 range."

Sep 1, 2019

By Stanislaw Nawrat, Waclaw Dziurzynski

An increasing concentration of coal production, especially in the circumstances of intensive methane inflow makes the coal mine managing staff apply new techniques of safe mining. It paves also the way for scientists to develop new directions of investigations and implementation of state-of -the- art technical solutions. Simultaneously, it could be noticed that the funds assigned for expansive 'En situ ' investigation are continuously decreasing. Better and better results are reached when applying computer technique in calculations of the parameters of ventilation process. Recent theoretical and experimental investigations of air and gas (methane) flow in longwall areas with caving, combined with the implementation of methane drainage system allowed to create, a mathematical model and consequently to elaborate a computer supported numerical simulation of discussed phenomena. The mathematical model has been modified and the simulation program was prepared in such a way that the software is convenient for a user looking for an optimal solution. The paper presented the methodology of optimal choice of following parameters: - ventilation system - rate of flow through the wall. The procedure takes into consideration keeping a safe level of concentration methane in air flowing through the longwall as well as the criterion of maximum methane concentration within the methane drainage pipe line. Results of variant computer simulation regarding the longwall with caving are shown in graphs and tables.

Jan 1, 1995

By William Wargo

The basic reason for lining underground cavities is to keep the cavity open during its useful life by providing adequately for the support of the surrounding rock and for the necessary degree of water tightness. This covers the entire field of support methods from the simpliest timber support to reinforced concrete in all its variations as applied to tunnels, galleries or shafts. The problem involved in the design of more efficient and economical lining systems for even bigger cavities has been magnified by increased speed of advance made possible by better blasting tecniques, improved tunneling machines and more efficient material handling. Tunnel lining today requires a disproportionate amount of time and money compared to other operations mostly due to the manuel labor involved in its installation. One solution to this problem is the developement of an entirely new concept in tunnel lining designed notoonly to overcome this bottleneck but also to open up the field for further increases in speed of advance. This new lining system acts first as a fast protective armour then becomes the concrete metal form and ends up as reinforcement sheet inside the concrete lining. This system developed and manufactured by Bernold A. G. of Switzerland since October 1968 has been installed in 25 applications in Europe under all ground conditions from stable rock to unconsolidated ground.

Jan 1, 1970

By K. Anim, C. Calderon-Arteaga

Located in Mojave, CA, The Soledad Mountain mine is an Open pit Heap-Leach gold Mine, which is operated by Golden Queen Mining Company LLC. under private capital. Open pit mining began in 2015 while full production was reached in 2016. The open pit mine feed a processing plant that can process more than 13K tons per day of ore which is sent to a heap leach pad. The Soledad Mountain project is a poly metallic deposit with Au and AG being recovered as payable metals. As the mine became bigger after moving to the east pit phases, Golden Queen was facing new challenges to control the production and accurately determine KPIs to improve/increase the production. To maximize returns and asset value, a new fleet management system (FMS) was adopted and implemented. The new FMS has enabled the mine to interconnect the different stages of the mining, as well as to recognize issues and implement the necessary corrections. With the associated increase in complexity in the process, the requirement of the ore control system to accurately predict ore feed characteristics is critical to maximizing metal recovery. Implementation of new daily and weekly plans were needed to ensure the ore delivery and meeting the tonnage goals, while allowed the equipment operators to better geolocate and to maximize the equipment production. These conditions alongside with Golden Queen’s drive to increase profitability and maximize net asset value has created challenges. These challenges are numerous and multifaceted. However, the ability to accurately route the material from the mine, is critical to site success and some of these challenges have been overcome by the adoption of the new FMS, the implementation of daily and weekly plans and upgrades in the ore control workflow. Examples of how the integration of the new systems allowed golden Queen to improve production strategy, are discussed in this article.

Mar 2, 2022

By J. D. Decker, T. E. Norman

Introduction Grinding is the reduction of ore and similar raw materials to particle sizes below the practical limits of commercial crushing ma¬chines. This size is about 36 in. (1 cm), in most cases, although some finer crushing machines are in regular use. The feed size to grinding machines may range upward to S in. in rod mills, and 12 in. or more in autogenous mills. The finest particle sizes produced in mineral processing operations result from grinding. Ordinary grinding of brittle materials is the result of impacting, rolling, and abrasion of heavy bodies, moving freely under the influ¬ence of gravity. These falling and rolling grinding bodies, which are usually of metal, must be much heavier and larger than the ore parti¬cles they break. This weight relationship is usually in excess of 100: 1. The sustained fall of the grinding bodies is obtained by placing them, together with the rock particles they grind, in a rotating drum or cylinder with horizontal axis, called a tumbling mill. The mill is nearly half full of grinding bodies and ore particles, which may be fed into one end and exit from the other through hollow trunnions which usually serve as the mill bearings. The mill lining must be thick to absorb wear and rough to prevent excessive slippage of the charge. The breakage of brittle rock or ore is accomplished by compression. The compression may be a rapid impact, from the fall and roll of a grinding ball, or it may result from the relatively slow and constrained motion as in a jaw crusher. Breakage by shear is a secondary result of the compressive motion. Ordinary rock has an extremely heterogenous structure with innumerable zones of weakness in which cracks, fractures, and breakages can form. When a rock is subjected to com¬pression it deforms. If the compressive force exceeds a certain critical value an incipient crack appears in the most fragile zones of weakness. This crack tip may first form on the particle surface or in its interior. When the first crack tip forms the compressive stresses immediately surrounding it flow to it, and this concentration of forces extends the crack and splits the rock. Other adjacent cracks may form during this extremely rapid process. Because of the nature of brittle particles, the work done in breaking them consists essentially of the work input required to compress them to the point at which the first crack tip forms. Breakage requires no appreciable additional energy input be¬yond that required for the deformation, since the stress energy already imported to the rock flows to the crack tip and extends it to breakage. Types of Tumbling Mills The general term tumbling mill includes the rod mill, ball mill, pebble mill, autogenous mill, and tube mill. It is of cylindrical or cylindro-conical shape and rotates about its horizontal axis. Rotational speed, liner type, and size and shape of tumbling media are selected to provide the desired operating conditions for the specific grinding application. Openings are provided through the mill ends for feed and discharge of the material being ground. A common feature of tumbling mills is the use of tumbling media

Jan 1, 1985

By Malcolm D. Flavel

As indicated in the introduction to this paper, it is a sequel to that which I gave to the last annual meeting in Atlanta in march. This paper goes further into aspects of crushing and screening, primarily from the standpoint of circuit control. There has been little published by equipment manufacturers on this subject and this is the first paper on crushing circuit control to be sponsored by Allis-Chalmers corporation. By proper control over the use of crushing energy, we will be able to produce finished products from feed materials uti¬lizing minimum capital for the lowest cost of production. The subject will be discussed as follows. Firstly, we will look briefly at what we are trying to accomplish; Secondly, what is presently available in the way of technology; Thirdly, we will look at a suggested new system of control which will best fit the parameters of the normal crushing and screening operation; As a conclusion, I will summarize the advantages of the new system.

Jan 1, 1977