Search Documents

By Harold J. Schock

The cases of no auxiliary ventilation and ventilation with tubing were mathematically modeled, using a turbulent dispersion model. The scooptram that is used to load is modeled as a variable-speed, variable-strength source of pollutants moving in and out of the dead-ended drift. Model predictions are compared to experimental measurements. A parametric analysis was performed to determine the effect of exhaust pipe location and time spent out of the drift, as well as to determine if a relationship existed between CO2 and NO levels. It was concluded from this analysis that when modeling a load-haul-dump cycle, it is necessary to use a model that has the capability of predicting changes in source strength as well as source location. It was also determined that four relevant factors include effective heading height, apparent longitudinal diffusion coefficient, transverse concentration gradient at the face, and average dispersion width of the exhaust jet. As these factors change with heading geometry and ventilation configuration, they were determined experimentally, Carbon dioxide was used as a tracer to calibrate the model; since, knowing the fuel flow rate, it is possible to calculate CO2 production. The above four factors in the computer model were calculated using a regression analysis, comparing predicted local concentrations to measured local concentrations. The model was then verified after this calibration process using additional experimental results. With the calibrated model, it is possible to predict pollutant concentrations at any location in the heading using an engine map and the previously calculated flow field. A parametric analysis shows that the exhaust pipe location can have a significant impact on operator exposure to exhaust gases. It was also shown that NO concentration varies directly with C02 levels. Predictions using the dynamic model are contrasted with constant source strength (pollutant flow rate) results. An analysis of these predictions for computing time-weighted average NO shows the dynamic model predictions of operator exposure to this pollutant to be less than one-half of the value predicted using a constant source model.

Jan 1, 1981

By Yucheng Li, De Huang, Yonghong Liu

Mine frictional resistance is one of the essential parameters of mine ventilation systems, and it is of considerable significance for the prevention and control of mine risks and accident hazards. Frictional resistance requires a lot of resources and time and has errors. To reduce the errors of frictional resistance, a regression model of frictional resistance is proposed based on the correlation analysis of the affecting factors. Through the comparative test analysis of seven regression methods, it is found that the classification and regression tree method for solving the proposed regression model has better performance than other methods. The least square error criterion is used to calculate and rank the importance of the factors affecting frictional resistance. The results show that the cross-sectional area of the tunnel, the support method, and the presence or absence of devices or pedestrian ladders have the most considerable influence on the prediction accuracy of frictional resistance. The support methods and cross-sectional areas are essential input variables. Through the combination test analysis of the influencing factors, the results show that the regression model does not have predictive ability when the number of input variables is less than 3 and the best predictive performance cannot be obtained using all the influencing factors. The best prediction model of resistance is to combine the shape of the tunnel, the support method, the presence or absence of devices or pedestrian ladders, and the cross-sectional area. The method proposed in this paper does not require a lot of resources and time investment, and the frictional resistance error is small. At the same time, it solves the problem of resistance prediction with incomplete data of influencing factors and provides a compelling new method for obtaining frictional resistance parameters.

Jan 28, 2022

By S. K. Kawatra, J. A. Halt

"Low-grade iron ores are finely ground and processed to recover iron-bearing minerals. However, the iron-rich powder is too fine to be used directly in blast furnaces and most direct reduction furnaces, and must be agglomerated or pelletized into a usable product called “pellets.” Bentonite clay has traditionally been used as a binder to make iron ore concentrate pellets, but it is expensive and contaminates the pellets. Organic binders may be a viable alternative to bentonite clay. This manuscript reviews organic materials that have been used to make iron ore concentrate pellets. Included are discussions on the development of organic binders, common pros and cons to organic binder use, organic binder structure and its effects on agglomeration, and additives to organic binders.IntroductionIron ore agglomeration turns finely disseminated, low-grade iron ores into a usable product, called pellets. During pellet production, fine-grained, iron-rich minerals are liberated from low-grade ores, concentrated, and agglomerated into round balls that are thermally hardened or cold-bonded to form pellets. Pellets are then transported to blast furnaces or direct reduction operations where they are used to produce iron; iron is further refined and shaped into the wide variety of steel-based industrial and consumer products in use today.Over the years, pellet production has become increasingly more prevalent with the increased exploitation of low-grade iron ores and increased iron and steel consumption around the world. In 2010, world iron ore pellet production was 388 Mt. It could be argued that the current pellet production process has been enabled by the use of binders – practical experience has shown that it would be nearly impossible to agglomerate iron ore concentrates using rotary drums and discs without using a binder."

Jan 1, 2015

By Oluwasegun Samuel Odebiyi, Shaona Wang, Feng Gao, Biao Liu, Hao Du

Recovering vanadium from vanadium titanium-magnetite (VTM) ore using ( NH4)2C2O4 is a clean hydrometallurgical process, but the drawback is the low recovery and slow kinetics due to the formation of inhibitor. A novel energy-efficient mathematical model was derived for green leaching of VTM in which the mechanical activation (MA) removed the inhibitor “δ” (formation of impermeable product layer of CaC2O4) covering the reacting core of the CaV2O6 leaching process in ( NH4)2C2O4 solution. Before the MA processing, the formation of the CaC2O4 layer affects the kinetics (slow) and NH4VO3 leachability (low recovery). The dissolution rate enhancement and economic importance (in terms of leaching kinetic/recovery) of mechanical activation (MA) pretreatment in hydrometallurgical processing cannot be overemphasized. It is shown from the experimental and developed mathematical model results that the rotating speed of the ball mill (ωb) has a significant effect on the NH4VO3 recovery. At 360 rpm, the experimental result gave an 82% optimum recovery rate and a reaction rate constant of 0.01889s−1 with close correlation with the present models at 82.8% and 81% for liquid-to-solid layer diffusion and chemical reaction controls, respectively, with a reaction rate constant of 0.018883s−1. The close correlation between the experimental recovery rate results and the diffusion recovery rate model result justifies that the leaching process is diffusion control shrinking core kinetic with experimentally measured activation energy (Ea) value of 19.502 kJ/mol . This present model proved that MA enhances the dissolution rate regardless of the formation of a passivation layer on the material and best describes the kinetics of the MA hydrometallurgical processes compared to the shrinking core model.

Nov 3, 2023

By Liangguo Kang

Coal, as one of the vital sources of energy in China, has raised widespread concerns regarding its safety issues amidst the country’s economic growth driven by coal. To address this concern, this study employed the Kuznets curve, multiple linear regression, and data envelopment analysis models to investigate the impact of Chinese coal economic development on coal mine deaths from 1992 to 2021. The findings revealed a clear correlation between the Chinese coal economy and coal mine deaths. Specifically, per capita coal output, the death rate per million coal tons, and the death rate per hundred thousand persons exhibited positive, negative, and negative correlations, respectively, with the growth of coal income over the past three decades. Moreover, when the coal workers and coal output factors remained unchanged, the income of coal demonstrated a negative correlation with future changes in coal mine deaths. Notably, with three decades of coal economy development, substantial improvements in coal mine safety have been observed in China. Consequently, this research provides valuable insights for formulating safety measures and policies in coal mines across different economic levels, as well as a useful framework for assessing safety development in the coal industry.

Jan 20, 2024

By James M. Barker

No commodity agreements now exist for sulfur and a lack of reference to sulfur commodity agreements exists in the literature. Law (1975) made a passing reference to sulfur as one of a group of commodities where "there have been additional control efforts of various types." Clearly, sulfur was a candidate, at least conceptually in the past, for some form of commodity agreement and the following discussion centers on the world sulfur market of the early 1980's in this context. GENERAL THEORY OF COMMODITY AGREEMENTS The upsurge in demands for commodity agreements seen in the last decade or so stems largely from agitation by the less developed countries (LDC) for better economic treatment by more developed countries (MDC). Several economic factors, real or imagined, adversely affect the LDC's as follows (MacAvoy, 1977): 1) variable demand in MDC's causes wide fluctuations in commodity prices which hurt the economies of commodity producers, who are often LDC's although consumer economies may also benefit from more predictable prices; 2) a general decline of commodity prices relative to the price of manufactured goods which hurts commodity producers in their balance of trade while their stocks and overcapacity rise; 3) instability of LDC economies enhanced by the above factors lowers internal stability, inhibits foreign investment, and retards economic growth; and 4) a lack of self respect when dealing with developed countries o, following the OPEC lead, LDC producers want the stature related to cartel market power.

Jan 1, 1985

By Mohammed Sakr

The empirical relationship between torque measured during installation and pile capacity has gained a wide acceptance in the helical pile industry in the last few decades. This paper presents a theoretical model developed to estimate torsional resistance of cohesive soils to helical pile installation. The proposed torsional resistance model was then used to establish torque factor, Kt, a factor that is widely used in the industry. The results of the study indicated that the Kt factor is a function of the load path (i.e. tension or compression), pile geometry and soil properties. The assessed Kt factors in tension and compression were validated by the results of 74 installation records and full-scale helical pile load tests. A parametric study was also performed to qualitatively assess the relative importance of different parameters that affect the Kt factors.

Aug 1, 2013

By William Gleason

"There are few people more qualified to speak of the tumultuous times in the global mining industry during the past four years than Newmont Mining Corp. president and chief executive officer Gary Goldberg.Goldberg stepped into his current position in 2012, just before MINExpo 2012. Gold prices had hit record highs not long before that ($54.15/g or $1,856.40/oz on Sept. 8, 2011), expansions were happening around the world and the gold mining sector was still living in the glow of one of its longest upswings in history.That all changed between April 8 and April 15, 2013 when the price of gold dropped by nearly $200/oz ($46.27/g or $1,586.20/oz on April 8 to $40.45/g or $1,386.80/oz on April 15), putting an end to the decade-long mining boom and forcing mining companies like Newmont to re-evaluateeverything.Three years later, with the gold sector recovering, Newmont Mining is not only surviving but is thriving with a pair of mines coming online, Long Canyon in Nevada and Merian in Suriname. On Oct. 1, the Merian Mine went into production on time and more than $150 million under the initial development capital budget.Goldberg, who was one of the featured speakers at the opening session of MINExpo International 2016 on Sept. 26, also spoke with Mining Engineering about the previous four years and the future of the industry.“Mining goes through cycles all the time and gold is no different,” Goldberg told Mining Engineering when asked about surviving the downturn since 2012. “I thought it was important that we take a good methodical and steady approach across the business to determine what was the right thing to do and to set the business up to improve performance. Anyone can cut costs for the short term, but we set out to do it in a sustainable and reliable way. We created a program we call Full Potential to look for sustainable ways to reduce costs and improve productivity. That program has taken more than a billion dollars out of our costs since we implemented it 2013 and that shows up in our results. Our all in sustaining costs are down 28 percent and our productivity is up 39 percent.”During the downturn, Newmont restructured its business model, sold off some assets and created a leaner, more nimble operation. It has paid off with the addition of two new mines and the acquisition of another, the Cripple Creek & Victor Mine in Cripple Creek, CO.“The gold industry had not seen a downturn in 12 years. We had half a generation that had not experienced a downturn, so helping them through that in an organized way and keeping a view toward the long term throughout the downturn was important. We were one of the few companies that continued to invest in assets,” he said."

Nov 1, 2016

By G. W. McMahon

Following the Sago Mine accident, the U.S. Mine Safety and Health Administration (MSHA) asked the U.S. Army Engineer Research and Development Center to study several possible methane explosion scenarios in the Sago coal mine. The study used a 0.3-m (1-ft) resolution map of the mine to produce a 3-dimensional (3 D) model of a portion of the mine, including the sealed area where the explosion occurred. An advanced 3 D computational fluid dynamics (CFD) code was used to calculate the explosion pressures within the sealed area, on the mine seals and in nearby regions of the mine. Based on the best available information on methane concentrations and assumptions on homogeneity and on layering and mix composition, three separate initial conditions of methane-air concentrations and location were studied. This paper discusses the CFD modeling technique, the results of the calculations, the challenges of conducting this type of modeling and the advantages and limitations of CFD modeling of accident investigations of mine explosions.

Jul 1, 2010

By G. ALBORNOZ, S. Utili, A. AGOSTI, C. VALDERRAMA, R. PELL, N. Morales

The steepness of the slopes of an open pit mine has a substantial influence on the financial return of the mine. The paper proposes a novel design methodology where overall steeper pitwalls are employed without compromising the safety of the mine. In current design practice pitwall profiles are often planar in crosssection and the profile in between ramps especially tend to be planar and defined by a constant inter-ramp angle. Sometimes rock layers exhibiting different strengths require the inclination of the profile to vary with depth, but the inclination across each layer is usually constant. Here instead, a new geotechnical software, OptimalSlope, is employed to determine optimal pitwall profiles of depth varying inclination. OptimalSlope seeks the solution of a mathematical optimization problem where the overall steepness of the pitwall, from crest to toe, is maximized for an assigned lithology, geotechnical properties and Factor of Safety (FoS). Bench geometries (bench height, face inclination, minimum berm width) are imposed in the optimization as constraints which bind the maximum local inclination of the sought optimal profile together with any other constraints such as geological discontinuities that may influence slope failure. The obtained optimal profiles are always steeper than their planar counterparts (i.e. the planar profiles exhibiting the same FoS) up to 8 degrees depending on rock type and severity of constraints on local inclinations. The design of a copper mine is first carried out employing planar pitwalls, secondly adopting the optimal pitwall profiles determined by OptimalSlope. The adoption of optimal slope profiles leads to a 34% higher net present value and reductions of carbon footprint and energy consumption of 0.17 Mt CO2 eq and 82.5 million MJ respectively due to a 15% reduction of rockwaste volume.

Mar 2, 2022

By Wolfgang Güter, Paolo Romualdi

Current extensions of the European railway network require long TBM drives in the diameter range of 10 m under critical and varying rock conditions. In view of that and in particular for a 7 km long high-speed railway tunnel in Spain to be started in mid-2003 a new design for a hard rock Double Shield TBM has been developed by SELI (Italy) and Jäger (Austria) in collaboration with Mitsubishi (Japan)and Robbins (USA). Due to the new design and operational features that new type of TBM has been named Universal Double Shield TBM with a further extended area of application. Special attention has been given to outstanding torque and thrust capacities combined with the shortest possible length of an innovative shield arrangement, different advance modes in various ground conditions and further developed exploration and treatment facilities.

Jan 1, 2003

When the Middle Ages were drawing to an end and Rotterdam, then still a small fishing port, began to extend its trade relations to continental ports handling general cargo, a development was initiated which was to give Rotterdam a predominant position in maritime traffic in Europe 300 years later. Despite many setbacks and the silting up of the mouths of the Rhine and Meuse rivers, the port experienced a new rise towards the end of the previous century after the dunes at Hook of Holland had been cut through as planned by Dutch engineer Caland. With its favourable location in the mouth area of the Rhine and a hinterland opened up by waterways it was merely a matter of the city council pursuing a far-sighted policy to make the best of these natural advantages. Thus new port installations were erected on the southern bank of the Meuse in the first quarter of this century, which were expanded in the course of the subsequent decades. The New Waterway became the main artery for industrial enterprises, in particular oil industries, which sprang up along its banks (picture 1). Whereas 30 years ago Rotterdam's Waalhaven, with its new jettees for general cargo and mainly bulk goods, was still one of the most modern terminals, the growing size of ships, which increased by leaps and bounds for tankers, in particular towards the end of the 'fifties, necessitated much larger harbour facilities built further and further towards deep water.

Jan 1, 1972

By M. N. Nabighian

Utilization of x-ray diffraction data for mineral identification has been well documented and accepted as an analytical tool in industrial and research organizations. However, the search for new methods to minimize errors affecting measured reflection intensities is being carried out by all concerned. Recent application of computer capability has greatly reduced the time required in handling data for mineral analysis and has increased the capability of accepting more data for greater precision. The purpose of this communication is (1) to describe the concept of cross-power in XRD analysis, and (2) to show that direct comparison analysis for multiphase systems has improved analytical accuracy when all available x-ray diffraction data are used in conjunction with high speed data processing by computer.

Jan 1, 1972

By I. Duckworth

P.T. Freeport Indonesia operates a mining complex located in the highlands of Papua, Indonesia. This district consists of underground and surface operations. The East Ertsberg skarn system (EESS) is one of the major orebodies in this district. Subsurface caving of the EESS has been carried out in a systematic series of mining lifts dating back almost 30 years. Present production from the third lift deep ore zone (DOZ), has reached 80 kt/d (88,000 stpd) during 2010, with this rate sustained through 2015. The orebody was proven below the existing caving level, with the next vertical block called the deep mill level zone (DMLZ).

Jan 1, 2010

By William J. Almas

Operating uranium mill tailings containment and mill decommissioning activities are regulated by the Nuclear Regulatory Commission (NRC) and the Environmental Protection Agency (EPA) through numerous regulatory mechanisms. Reduction of radon emissions from tailings disposal areas, remedial actions to return groundwater to baseline constituent concentrations, and 200-to 1,000-year stabilization of tailings are major focus areas of regulation. The cumulative economic impact and uncertainty associated with regulation are very significant and will hinder future development of uranium milling facilities.

Jan 1, 1991

By James Charles McHardy

During 1980-2000, the Florida Phosphate industry will deplete its Central Florida Polk County reserves. As a result, new mines will be built in the ?so-called? Southern Florida Reserve areas. These new mines will require new mining, beneficiation and tailings disposal technologies in that the southern reserves have different characteristics than have been encountered in the Central Florida deposits furthermore, government regulations will necessitate the development of new tailings and clay disposal methods. This paper reviews these challenges for the phosphate industry and how these opportunities can be expected to effect plant design and plant operating practices.

Jan 1, 1981

By Xiaozhen Song, Ashish Ranjan Kumar, Shimin Liu

To investigate the influence of boreholes, fans, and curtains for large opening underground mines (LOUM), we conducted a field survey for LOUM with the survey data serving as the numerical modeling inputs using computational fluid dynamics (CFD) models. Five different CFD modeling results were obtained with different borehole, box fan, and curtain setting conditions. The results indicate that most air quantity directly escapes through outlet 1 after coming into the inlet, causing a huge loss of airflow; volumetric air exchange index (VAEI) and minimum hours of fully exchanging the air (MHFEA) measure air exchange efficiency, with zone 2 of case 5 having the highest VAEI; The borehole minimally affects zones 2, 3, and 4, but drastically alters airflow direction in zone 1; The box fan enhances airflow to zone 2, improving ventilation efficiency and increasing VAEI; Curtains have little effect on distant working faces but influence airflow near inlets and outlets. This study provides a foundation for future research on the influence of boreholes, fans, and curtains, as well as optimizing their placement and effectiveness in face ventilation.

Feb 22, 2026

By Hasan Ali Taner, Vildan Onen

One of the problems in flotation is mechanical entrainment and the other is the presence of complex gangues (especially clay minerals). In the present study, it was aimed to determine the effects of clay types (kaolinite, illite, and montmorillonite) on mechanical entrainment parameters (total flotation recovery, real recovery, mechanical entrainment recovery, and water recovery). Effects of clay types and clay amount on chalcopyrite flotation were investigated by flotation experiments. Interaction mechanisms between the clay minerals and ore were characterized using SEM–EDS analyses. Experiments were carried out with and without a collector using the mixture of clay minerals and ore under certain experimental conditions. While the clay mineral most affecting the chalcopyrite grade was montmorillonite, the highest mechanical entrainment recovery and the lowest real recovery values were obtained in the presence of illite. While illite is stated as the least problematic clay mineral in the literature, it was determined that illite among three clay minerals used in this study caused significant mechanical entrainment. In contrast, it was determined that increasing the amount of kaolinite did not have a significant effect on mechanical entrainment. This study’s findings will guide in determining of clay minerals’ effect on gangue entrainment in flotation.

Dec 29, 2023

By Samir Kumar Pal, Rajasekar Rathanasamy, Gobinath Velu Kaliyannan, Moganapriya Chinnasamy, Sathish Kumar Palaniappan

The research examines the performance of uncoated and coated tungsten carbide-cobalt rock cutting bits. It aims to optimize process variables (cutting speed, depth, coating material) considering multiple output responses (cutting forces, specific energy, wear rate, material removed, angle of reaction forces). The study uses a hybrid optimization technique combining Taguchi design, grey relational analysis, and fuzzy logic. The optimal parameter combination was found to be cutting speed: 200 mm/s, cutting depth: 6 mm, and titanium aluminum silicon nitride coating.

Apr 24, 2022

By SONGHE WANG, YI XUE, PENG HOU, CAIHUI ZHU, XUANYE JIAO, Feng Gao

The abstract discusses the challenges of coalbed methane development in China due to low coal seam permeability. It highlights protective layer mining as a method to reduce in-situ stress and enhance permeability for improved gas drainage and disaster prevention. The study involves experimental and numerical simulations to analyze gas migration and permeability changes during stress release. It includes a stress-strain-seepage coupled test on coal, development of a mathematical model for coal seepage under mining unloading, and a numerical model based on the Wulan coal mine to explore in-situ stress release, permeability evolution, and gas drainage in an unloaded coal seam. The aim is to demonstrate the effectiveness of combining protective layer mining and gas drainage technology for gas outburst risk elimination.

Mar 14, 2022